Special Repair To Bldg No. P-328, Addition / Alteration And Upgradation Of Corridor And Dressing At Single Offrs Living Accn And Provision Of Toilet For Guards At Aagosh At Cme Pune Special Repair To Bldg No. P-328, Addition / Alteration And Upgradation
Tender Value
49.45 Lakhs
Estimated cost
Bid Submission
09 Apr 2022
0 days left
EMD
98900
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kirkee → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Special Repair To Bldg No. P-328, Addition / Alteration And Upgradation Of Corridor And Dressing At Single Offrs Living Accn And Provision Of Toilet For Guards At Aagosh At Cme Pune Special Repair To Bldg No. P-328, Addition / Alteration And Upgradation Of Corridor And Dressing At Single Offrs Living Accn And Provision Of Toilet For Guards At Aagosh At Cme Pune
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of single layer Mangalore Pattern roof tile laid dry complete all as specified and directed |
| 2 | All as per item No. 1 above, but bedded in lime or cement mortar complete all as specified and directed. |
| 3 | Dismantling battens for tiles, shingles etc, of any size including tilting fillets spacing exc 15 cm complete all as specified and directed. |
| 4 | Dismantling timber scantlings 40 sq. cm and over in section, in any position all as specified and directed. |
| 5 | S&F Framed work such as roof trusses(framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410-W (Gde E-250) Quality A complete all as specified and directed., |
| 6 | S&F rolled sections as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W (Gde E-250) Quality A complete all as specified and directed. |
| 7 | M & L for preparationof new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed |
| 8 | S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc. complete all as specified and directed. |
| 9 | S & F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley, gutters etc. complete all as specified and directed. |
| 10 | Dismantling water tanks and removing capacity exc. 500 & n.exc. 1000 ltrs complete all as specified and directed. |
| 11 | S&F 1000 ltr. capacity rotational moulded polyethylene water storage tanks cylindrical vertical with closed top hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed. |
| 12 | M&L 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and directed. |
| 13 | Demolition of cement concrete (un-reinforced)in roof/floors other than ground level beam, stair case, landing, chajjas and similar items includingwater proofing treatment in any layers and removal of debris to distance exceeding 250m and not exceeding 500m from the site complete all as specified and directed. |
| 14 | M&L PCC 1:2:4 (Type B1 using 20mm graded stone aggregate) as in levelling course to match the undulations of roof and in in coping, roof kerbs, fins including benching etc complete all as specified and directed |
| 15 | M&L 10 mm thick cement screed in CM 1:3 mixed with water proofing compound of approved make over RCC roof slab and vertical surface, finished even and smooth by using steel trowel complete all as specified and directed. |
| 16 | M&L for APP based polymeric membrane minimum weighing 3.50 kg/Sqm and minimum 3mmthick reinforced with polyster non wovenfabric (wt not less than 160 gm/sqm) laidoverprimed surface including bituminous primer conforming to IS-3384-1965 applied @ 0.3 ltr/ Sqm by torch application complete all as speficied. |
| 17 | Three course roof treatment consists of as under :- |
| 18 | Applying one coat of bituminous primer conforming to IS-3384-1965@ 0.30 ltr/Sqm |
| 19 | laying APP based membrane as specififed. |
| 20 | Applying a layer of blown gradebitumen85/25 @ 1.2 Kg/Sqm conforming to IS : 702 |
| 21 | Supply laying of Geo textile fibre over & above membrane as per manufacturers instruction all as specified and directed. Geo TextileMake : Garware Ropes Ltd. |
| 22 | M&L for 15 mm thick screed bed in cement mortar 1:6mixed with water proofing liquid for receiving cement tiles complete all as specified and directed.(WPL Shall be measured and paid separately) |
| 23 | Supply only liquid water proofing liquid complete all as specified and directed. |
| 24 | M&L forcement concrete tiles 25 cm x 25 cm x 22 mm thick, machine pressed set jointed with CM 1:3 mixed with 5% crude oil by weight of cementcomplete all as specified and directed. |
| 25 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and directed. |
| 26 | Demolition of cement concrete (unreinforced ) in ground floors and pavings not exceedidng 15cm thickness (below or above ground level) all as specified and directed. |
| 27 | M&L for 75mm thick PCC type D-2 (1:4:8) using 20mm graded stone aggregate as in sub base etc complete all as specified and directed |
| 28 | M&L For 25 mm thick,type B-0, 1:2:4 (12.5mm graded stone aggregate) as in floor etc complete all as specified and as directed. |
| 29 | M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wallfinishes in CM 1:6 complete all as specified and as directed. |
| 30 | M & L vitrified ceramic tiles 10 mm thick (square/ rectangular) light shade, polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed, |
| 31 | M & L non- skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. complete all as specified and directed, |
| 32 | M & L vitrified ceramic tiles 10 mm thick (square/ rectangular) light shade, polished, area of each tiles not exceeding 0.36 sqm, inskirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed. |
| 33 | M& L For rendering 10mm thick cement mortar 1:4 as inbacking coat for fixing tiles complete all as specified and directed |
| 34 | M&L for glazed ceramic coloured tiles in vertical surface 350mmx250mmx7mm /450mmx350mmx7mmthick set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and directed |
| 35 | Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premises complete all as specified and directed. |
| 36 | M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 37 | All as per item No. 33 above, but in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement to match complete over and including 10mm thick cement mortar in CM 1:4 as backing coat for fixing tiles complete all as specified and directed. |
| 38 | M& L for 20 mm thick, granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cementmortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and as directed.. |
| 39 | M&L machine cut cuddappah stone slab 20-25mmthick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 40 | Roundidng to edges of stone slabs, such as insteps, cooking platform and other similar situation complete all as specified and directed. |
| 41 | Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit all as directed. |
| 42 | All as per item No. 38 above, herein before but 20mm bore |
| 43 | S&F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specified and directed. |
| 44 | S&F 20mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specified and directed. |
| 45 | Refixing 15mm bore old serviceable steel water tubing obtained from sl item No. 38 & connection in new or old position of wall, ceiling, floor etc all as specified and directed |
| 46 | All as per item No. 42 above, but 20mm bore old serviceable tubing obtained from sl item No.39 |
| 47 | S&F in repair vitreous china wash basin, white, flat back, size 630x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, waste coupling complete all as specified and directed. |
| 48 | S & F under counter wash hand basin vitreous china coloured including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste fitting union and32mm dia PVC waste pipe 90cm long, all necessary inlet outlet connections complete all as specified and directed.Make : Hindware Cat No. 10065 or equivalent model in Cera /Parryware/ Neycer as approved by GE. |
| 49 | M & L for coupled closet (Clover) snow white make Cera including P or S trap alongwith cistern dual flush complete set and soft close plastic seat cover complete all as specified and directed including taking down old wash down water closet pan of any description complete all as specified and directed. Make- CERA Cat. No. S1013115 S Trap / P Trap or equivalent model in Parry ware (Super fine), Hindware as approved by GE. |
| 50 | S&FVitreous China wash down water closet pan (pedestalpattern), white (excluding fixing bolts, flushing cisternand flush pipe) including seat cover complete all as specified and directed |
| 51 | S&F in repair 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed. |
| 52 | S&F For in repair brass chromimum plated two way bib cock fancy type, 15mm bore (min Wt. 550 grams) of approved make by EIC/ GE etc.complete all as specifed and as directed. |
| 53 | S & F brass chromium plated, 15 mm bore health faucet, ( flexy type) 1.00 mtr. long of approved make by EIC/GE etc. complete all as specified and as directed. |
| 54 | S&F in repair 15 mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long shanks and flynuts, screwed for iron pipe complete all as specified and directed. |
| 55 | S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed, |
| 56 | S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed |
| 57 | S&F in repair 15mm dia stop valve chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and directed. |
| 58 | M&L cement concrete type E-2, 1:5:10 (40 mm graded stone aggregate) lean concreteas in sunkun floor for filling etc.complete all as specified and directed. |
| 59 | M&L 40mm thick cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in sunkun floor complete all as specified and directed. |
| 60 | M&L 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed. |
| 61 | Supply only integral WPC all as specified and directed. |
| 62 | M&L bitumen blown any grade applied hot, two coats to concrete surfaces at the rate of 1.5 kg per sqm per coat complete all as specified and directed. |
| 63 | M&L Polythene film black 50 micron laid in floor complete all as specified and directed. |
| 64 | S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 65 | All as per item No. 61 above, but 110mm complete all as specified and directed. |
| 66 | S&F in repair 75mm PVC (SWR) bend any radius complete all as specified and directed |
| 67 | All as per item No 63 above, but 110mm dia complete all as specified and directed. |
| 68 | S&F in repair 75mm PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed. |
| 69 | All as per item No. 65 above, but 110mm bore of pipe complete all as specified and directed. |
| 70 | M&L in repair 75mmPVC (SWR) floor trap with grating including jointing with solvent cementcomplete all as specified and directed. |
| 71 | All as per item No.67 above, but 110mm complete all as specified and directed. |
| 72 | S&F in repair 75mm PVC (SWR) vent cowl complete all as specified and directed. |
| 73 | All as per item No.69 above, but 110mm complete all as specified and directed. |
| 74 | S&F in repair stainless steel sink, made out of 1.00 mm thick sheet for kitchen with plug, washer pipe cast iron cantilever brackets, connecting union overall size 495x420mmbowl size 410mm x 330mm x160mm all as specified and directed. Make: Nirali/Diamond/Blue King/Kingston/ |
| 75 | S&F decorative designer looking mirror of selected quality 5.50 mm thick mounted on 2mm thick laminated PVC sheet with necessary fixing arrangement complete as specified and directed. |
| 76 | S&F in repair brass chromium plated tubular towel rail, 20mm dia , D type 60cm long between flanges complete all as specified and directed. |
| 77 | M&L for stainless steel 202 material staircase railing of ht 1.00 m with Top rail pipe 50mm bore (16 gauge), vertical pipe 40mm bore (16 gauge) @ not exc 1.00 m c/c and at turning and corners with 10 mm thick toughened glass of height 0.75 m and necessary fitting for fixing of glass,including Tee, cross, bend, base coupling, fixed in floors with necessary fastner complete glossy finish complete all as specified and directed. |
| 78 | S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stain steelbracket guard and railing 60 cm long etc. complete all as specified and as directed. |
| 79 | S& F in repair Soap dish holdercomplete as specified and directed. Make : Jaquar |
| 80 | S&F Toilet paper holder, vitreous China, box type complete all as specified and directed. |
| 81 | S& F Brass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed complete all as specified and directed. |
| 82 | Taking down chowkats or frames with shutter (without taking off shutters from the frames) not exc 1.5 sqm each and removing from site complete all as sepcified and directed. |
| 83 | All as per item No. 79 above, but exc 1.5 sqm and n.exc 4 sqm complete all as specified and directed. |
| 84 | S&F 2nd class hard woodplain solid straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed |
| 85 | S& fix 2nd class hard wood 35 mm thick factory made glazed and skeleton shuttersopen rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and directed. |
| 86 | S& fix factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered particle board with commercial face veneers fixed to chowkhat. The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified and directed |
| 87 | M&L for preparing new surface of wood of any decription , not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 88 | S & F mild Steel works as in bands straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminous paint and sanded, complete all as specified and directed |
| 89 | M & L for preparing surface of iron and treating small articles such as stop, covers, gully grating, holdfasts, end of posts area exc 0.1 Sqm each treated with tar or coal tar black paint complete all as specified and directed. |
| 90 | M & L for cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, step, seismic and other similar bands, plith courses, string courses, lacing courses, parapets, railing upto 60cm height, kneelers, apex stone, copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directted. |
| 91 | S & F powder coated Aluminium sliding windows three track with two glass shutters using 5 mm thick glass tinted and one shutter with stainless steel wire gauge wire cloth 0.31mm nominal dia of wire and width of aperture 1.61mm, using aluminium powder coated sect, aluminium cleat, PVC track, bearing, handle lock rubber beading, etc complete including taking down old window of any size. Note:Size of aluminum sections are as under :-(i) Three track top & vertical – Jindal main – 2010 Section No 20621.(ii) Three track bottom - Jindal main – 2010 Section No 20620.(iii) Shutter vertical section - Jindal main – 2010 Section No 20606.(iv) Shutter top & bottom - Jindal main – 2010 Section No 20604(v) Shutter vertical middle (interlock) - Jindal main – 2010 Section No 20605. |
| 92 | S & F aluminium powder coated ventilators partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr)frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick)(wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc including taking down old ventilator etc. complete all as specified and directed. |
| 93 | S & F solid PVC doorframe of size 50mm x 47mm made out of5 mm plain colour PVC sheet reinforced with M.S. square tubeetc all as specified and as directed. |
| 94 | S & Ffactory made solid PVC moulded door shutter, 30 mm thick 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and as directed. |
| 95 | M&L 18/19mm thickPre-laminated board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw to timber frame including taking down existing board of any description complete all as specified and directed. |
| 96 | Extra over rates of block board or veneered particle board for external teak wood 18/19mmlipping 6mm thick fixed with nails complete all as specified and directed. |
| 97 | M&L 18/19mm thick particle board, medium density, flat pressed single line layer type or three layer type with BWR type adhesive fixed with screws to timber frame including dismantling existing board complete all as specified and directed. |
| 98 | S&F 150mm hasp and staple, mild steel, wire type stove enamelled black, including bolt to hinge plate and fixed with screw complete all as specified and directed. |
| 99 | S & F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as specified and directed |
| 100 | M&L barrel tower bolts stove enamelled black of size 200 mm complete all as specified and directed, |
| 101 | M&L barrel tower bolts stove enamelled black of size 150 mm complete all as specified and directed |
| 102 | S&F 125mm long aluminium anodised handles or extruded section complete all as specified and directed. |
| 103 | S&F 150 mm long aluminium anodised handles or extruded section complete all as specified and directed. |
| 104 | S&F 300mm long Aluninium alloy, anodised , sliding door bolt with hasp , staple, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. |
| 105 | S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 106 | S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staples complete all as specified and directed. |
| 107 | Demolition of brick or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed. |
| 108 | M&L precast solid block masonry of block 1:3:6 type C-1 using 20mm graded stone aggregate, wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed. |
| 109 | M&L 15mm thick plastering on concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed. |
| 110 | Raking out joints/pointing to random rubble masonry, polygonal rubble uncoursed or brought upto course complete all as specified and directed. |
| 111 | M&L raised pointing in CM 1:4 to random or polygonal rubble, uncoursed or brought upto complete all as specified and directed |
| 112 | Taking down cement plaster on brick or stone walls or concrete surface etc including raking out joints, hacking for key scrubbing down with water complete all as specified and directed. |
| 113 | M&L rendering 15mm thick on stone masonry surfaces in CM 1:6 finished even and smooth with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed. |
| 114 | M&L rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth with sagol all as specified and directed. |
| 115 | M&L 15mm thick cement plastering on concrete surfacesin CM (1:4) finishing surfaces even and smooth without using extra cementcomplete all as specified and as directed. |
| 116 | M&L preparing newly plastered surfaces of wall and applying complete wall with3 mm POP/Birla putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed. |
| 117 | M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling all as specified and directed. |
| 118 | M & L for complete removal of existing treatment from walls, filling the holes/cavities and platering the surface required, cleaning and preparation of the surfaces and applying complete wall with 3mm POP/Birla putty and making smooth surfaces and applying two coats of exterior emulsion paint 100% acrylic over a coat of primer as per manufacturers instruction complete all specified and directed.Note : The rate quoted by the contractor shall include for scaffolding to carry out the work for height more than 10.00 mtrs. |
| 119 | M&L complete removal of existing treatment and applying 3mm thick Birla wall care putty and applying two coats of Oil bound distemper white or tinned over one coat of primer on walls, etc all as specified and directed. |
| 120 | All as per item No. 116 above, but two coats of cement base paintwithout wall care putty complete all as specified and directed. |
| 121 | All as per item No. 116 above, but two coats of white wash on ceiling complete all as sepcified and directed. |
| 122 | S&F in repairs 19/20mmdia MS pipe powder coated of approvedcolour as in decorative type curtain rods including brackets for fixing curtain rod all as specified and as directed. |
| 123 | S&F in repairs brackets powder coated of approved decorative type suitable for fixing curtain rods of 19/20mm dia pipe incl fixing screws, drilling etc as per sample approved by Engr-in-charge all as specified and as directed. |
| 124 | M&L cement concrete 1:3:6 type C-2 (40mm graded stone aggregate) as in floors, plinth protection, path etc 75mm thick smooth finished surface without using extra cement complete all as specified and directed. |
| 125 | Chipping off loose concrete/plaster upto sound stratum of RCC members such as slab, chajjas, columns, beams and clean the surface with wire brush, washing down with water using water jet including necessary scaffolding & propping to support the structural members where work is to be executed and removing debris to a distance exc 250 metre but n. exc. 500 metre. |
| 126 | Dismantlingwall and ceiling boards (fibre, pulp, insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 127 | M & L for false ceiling with 4mm thick designer\"E\" board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size24mm x38mm x 0.7mm cross tee of size24mm x 28mm x 0.7 mm using purpose made members interlocking to each other and with 40mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wireand making holes etc all as directedincluding two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction make of GI Grid work : Armstrong/Swastik/Techno Grid and MakeE boardGypsum or equivalent approved . |
| 128 | M & L for provinding and applying rust inhibition coat system (in two coats) as per manufacturer\"s instructions to exposed reinforcement after cleaning and removing scales and rust complete all as specified and directed. |
| 129 | M & L for provinding and applying a bond coat (epoxy based bonding materials) to all exposed concrete surfaces all as per manufacturer\"s instructions complete all as specified and directed |
| 130 | Supply and fixkitchen cupboard of size7\" x2.6\"using HDHMR Board 18mm thick bothside laminated any colour ,18mm thick shutter ,8mm thick back board and18mm thick vertical support &horizontal shelfs including necessary fittings of SS hinges with soft close ,Gunmetal handle,complete all as shown on line Drgspecified and as directed. Make : (i) HDHMR board : ACTION TESA (or) Equivalent (ii)HARDWARE :EBCO (or) Equivalent (III) HANDLE : RICH(or) Equivalent |
| 131 | M & L for providing & applying latex polymer modified cement mortar in specified composition of system [i.e. cement 400 parts by weight, quartz sand 1600 parts by weight, polymer 60 parts by weight, water 120 parts by weight ] to RCC surfaces all as per manufacturer\"s instructions and as directed. [ Note : Thickness of plaster/filling varies from 15mm to 25mm] |
| 132 | M&L treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apartincluding drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and directed. |
| 133 | Cutting chases, pinning in, makinggood to facings where required andpointing in cement mortar 1:3 toends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduitwiring, etc. and making good, cutting exceeding 20cm girth |
| 134 | S & F in repair 15mm dia bore copper alloy chromium plated kitchen sink mixer with regular swinging casted round shape spout swan necked. Make : Prayag Cat No: 8560 or equivalent |
| 135 | Excavating in trenches, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc. 10 sq m on plan and n. exc. 1.5 m in depth and getting out in hard/ dense soil |
| 136 | Excavating in trenches, n. exc. 1.5 m wide and n exc 1.5 m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc. 10 sq m on plan and n. exc. 1.5 m in depth and getting out in soft/disintegrated rock |
| 137 | M&L for cement concrete 1:4:8 type D-2, (using 40 mm graded stone aggregate)as in foundations, filling and mass concrete etc. complete all as specified and directed. |
| 138 | Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar, complete, in walls |
| 139 | M&L for RCC 1:2:4 type B-1, (using 20 mm graded stone aggregate) as inbeams, cantilevers, bed block, bressummers, lintels over 1.5m span, including necessary form work etc . complete all as specified and as directed. |
| 140 | S&F For 5mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane |
| 141 | S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) |
| 142 | S&F 600mm x 450mm bevelled edge mirror or selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chroimium plated brass screws and cup washers complete all as specified and directed. |
| 143 | S&F Shower rosearm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour. (Minimum weight 40gms) |
| 144 | S&F F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290. Gde-E-165 etc complete all as specified and as directed |
| 145 | S&F For vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including spreader etc. complete all as specified and directed. |
| 146 | M&L preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over one coat primer on walls complete all as specified and directed. |
| 147 | M&L Preparation of newly plastered or unplastered surfaces on wall surfaces and applying two coats of cement base paint complete all as specified and directed. |
| 148 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point |
| 149 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. |
| 150 | Taking down carefully copper/aluminium point wiring (light, fan,bell, socket or power) complete, including fixture and fittings such as switches, Ceiling rose,pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking creditand making good disturbed surfaces of walls, floors, etc . credit for above items should be made as per conditions separately. |
| 151 | Taking down ceiling fans any type/sweep 230 V AC and deposited to E/M store yard for disposal action. |
| 152 | M&L for point wiring for light/fan/Bell with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing/capingwith all accessories and 1.50 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly inclPVC box surface type with PVC modular white cover plate for mounting fittings such as switches, sockets, fan regulatorsetc complete all as specified and directed for one light/fan /bell point controlled by one switch & making goodto disturbed surface of wall etc |
| 153 | All as per item No.149 above, but for one multipin 5 amps socket outlet on same board.with other switch complete all as specified and directed. |
| 154 | All as per item No.149 above, but for one multipin 5 amps socket outlet on independent board with other switch complete all as specified and directed. |
| 155 | All as per item No.149 above, but for one light point controlled by 2, 2 way switch complete all as specified and directed. |
| 156 | All as per item No. 149 above, but with 2.5 sqmm cable and 2.5 sqmm for earth continuityfor multipin 15 amps socket outlet flush type on independent board complete all as specified and directed. |
| 157 | S & Fceiling rose, 3 phase PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal incl PVC square block complete all as specified and directed. |
| 158 | S & F lamp holder, PVC/polycarbonate type with back plate suitable for batten fitting incl PVC square block complete all as specified and directed. |
| 159 | S & F call bell ding dong AC, 230 Volts, single pole complete all as specified and directed. |
| 160 | S&F switch modular, one way 6 amps, 1 module with suitable plate and cover complete as per existing make and model all as specified and directed. |
| 161 | S&F switch modular, two way 6 amps, 1 module with suitable plate and cover complete as per existing make and model all as specified and directed. |
| 162 | S&F switch modular one way 16 amps, 1 module with suitable plate and cover complete as per existing make and model complete all as specified and directed. |
| 163 | S&Fsocket modular 6A, 2/3 pin combined 2 module with suitable plate and cover complete as per existing make and model complete all as specified and directed. |
| 164 | S&F socket modular 6A/16A, 2/3 pin combined 2 module with suitable plate and cover complete as per existing make and model complete all as specified and directed. |
| 165 | S&F modular fan regulator step type 120W, 2 module with suitable plate and cover complete as per existing make and model all as specified and directed. |
| 166 | S&F modular bell push 6 Amps 1 module with suitable plate and cover completeas per existing make and model all as specified and directed. |
| 167 | S&F surface and wall mounted LED batten(LED tube light fitting 20W) with polycarbonate housing & integrated electronic driver alongwith LED tube 20 watt and 02 Nos PVC square blocks incl taking down old UNSV fitting.Make:- Havells cat No LUMILINEBS20WLED830SPCWH or equivalent of Philips/Bajaj |
| 168 | S&F surface and wall mounted LED batten (LED tube light fitting 10W), extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver alongwith LED tube 10 watt and 02 Nos PVC square blocks incl taking down old UNSV fitting. Make- Havells cat No ENDURALINEARNEOBS10WLED830SPCWH or equivalent of Philips/Bajaj |
| 169 | S&Fendura gugby NEON- IP 65 environmental friendly, ultra modern energy saving surface mounted decorative oval bulk head edge lit LED luminaire comprising of high brightness LED 10 Watt incl taking down old UNSV fitting. Make- Havells cat No RUGBYNEONFT10WLED860SSYMTOPC or equivalent of Philips/Bajaj |
| 170 | S&F building securityLED light fitting 25 Watt, energy saving and environmental friendly long life LED fitting made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 incl taking down old UNSV one.Make - Havells cat No ENDURAPEARLSL25WLED757SASYTOPC or equivalent of Philips/Bajaj |
| 171 | S&F decorative wall light fittings(bracket light), CITY 3 made up of polycarbonate suitable for 10 watt LED lamp incl LED lamp incl taking down old UNSV one. Make:- Havells cat No LHDL06160099 or equivalent of Philips/Bajaj |
| 172 | M&L for sub main wiring with two run of6 sqmm single core multi stranded PVC insulated and unsheathed copper conductor(red for phase and black for neutral) of grade 1100 volt FRLSH cable in and including 1100 volt electrical grade PVC casing capingof desired colour not less than1.2 mm thick and 25 mm wide& 6 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and as directed incl taking down old unserviceable one. |
| 173 | All as per item No 169 above, but size 4 Sqmm two runs andwith one run 4.0 sqmm FRLSH copper wire for earth continuity. Make of wire-- Finolex/Havells/Polycab/Plaza.. |
| 174 | S&F in replacement enclosure, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps, 240 volt complete all as specified and directed. |
| 175 | S&F in replacementMCB distribution board Double door SPN 240 volts 8 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc complete all as specified and directed. |
| 176 | S&F in replacementMCB distribution board double door240volts 4 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls complete all as specified and directed. |
| 177 | S & F in replacementMCB SP 5 to 32 Amps, 230 V AC complete all as specified and directed. |
| 178 | S & Fin replacement MCB SPN 40 Amps, 230 V, AC complete all as specified and directed. |
| 179 | S & Fin replacement MCB SPN 20 Amps, 230 V, AC complete all as specified and directed. |
| 180 | Taking down old unsv earthing and M&L for earthing complete with 600x600x60mm GI earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5m below ground level, connected to and including GI strip of size 25x4 mm by means of bolts, nuts and check nuts and washers to the extent of 7.5 metres as earthing lead and connecting to the eqpt/machinery etc. incl charcoal dust and common salt packed all around the earth plate in alternate layer in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including chamber made up of PCC 1:2:4 type B1 with M.S. angle iron frame, C.I. Cover,20mm dia light grade G.I pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement incl excavation and earth work in any type of soil and testing complete all as specified and directed. Note :- GI Strip more than 7.5 mtr will be measured and paid separately. |
| 181 | M&L in replacement of LED lamp 9 watt complete all as specified and directed. |
| 182 | Supply, install in replacement LT panel board wall mounted self supporting compartmentalised design of suitable size to accommodate the LT switch gears & other accessories suitable for 440 volt 3 phase 4 wire made out of 2.0mm CRCA sheet powder coated having gasketed front two hinged doors with locking arrangement including bottom and top detachable gland plate complete with suitable size of rust proof nuts bolts and washers etc comple with mounting accessories including the following :- (a) Four copper bus bar 200A mounted on epoxy insulators provided with rust proof nuts bolts and washer (b)MCCB 4 pole 160 amps 25 KA-1 Nos (c) MCB SPN 63 amps -04 Nos (d) Temperproof electric meter 0-60 amps -04 Nos (e) LED indicating lamp-3 Nos(RYB) (f) Ammeter 0-200 amps with CT coil and selector switch -01 set (g) Voltmeter 0-500volt with selector swtich-01 No(h) MCB SP 6- 32 Amps-04 Nos |
| 183 | Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc including taking down old existing one and deposited to AGE E/M store yard. Note: - type of geyser i.e vertical/horizontal type shall be decided by Engr-in-Charge as per site requirement. |
| 184 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC). |
| 185 | Taking down old unsv exhaust fan and deposited to AGE E/M store yard complete all as specified and directed. |
| 186 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm complete all as specified and directed. |
| 187 | Material & labour point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable in and including PVC concealed conduit of 25mm dia or higher medium grade complete with and including all PVC conduit accessories/fittings, brass crews, washer etc. sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated solid copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for the followings:- |
| 188 | One light point controlled by one switch 5 Amps |
| 189 | One exhaust fan point controlled by one switch |
| 190 | Socket outlet, three pin, 5 Amps, independent |
| 191 | Socket outlet, three pin, 5 Amps on the same board |
| 192 | S & F switch piano, flush type, single pole, one way and 6 Amp, 230 Volt complete all as specified and directed. |
| 193 | S & F socket outlet 2 in 1, 5 pin, 5 Amps flush type complete all as specified and directed. |
| 194 | Supply & fix surface wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonated diffuser and integrated electronic driver for LED tube complete with retrofit LED energy saving ecess/surface mounted luminaries, high efficiency diffuser for soft glare fee light of capacity 20 watt suitable of operation on 230 Volt 50 Hz AC supply complete all as specified and directed. Make: Cat PAt No. ENDURALINEAREOBS20W LED865SPCWH of Havells or equivalent model in Wipro/CGS/Bajaj |
| 195 | Supply & fix exhaust fan made of strudy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300mm incluyding all fixing arrangement all as specified anddirected. |
| 196 | Supplying & fixing 1100 Volts grade heavy duty cable PVC insulated aluminium multistranded conductor of size 6 Sqmm, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm suspension wire, one twin core cable flat or circular |
| 197 | Supply & fixing of MCB single pole rated capacity 5 to 32A, 240 V breaking capacity 10 KA C series. |
| 198 | Supply & fixing of MCB single pole and neutral rating capacity 40 to 63 Amp, 240 V breaking capacity 9KA C series. |
| 199 | M & L for earthing complete with GI earth plate electrode 60x60cmx6mm thick burried directly in ground in earth pit not less than 2.25 mtr depth below normal ground level with top edge of the plate vertically to depth of not less than 1.5 mtr below ground level connected to & including GI lead 4 mm dia as earthing lead connecting to equipment by means of GI bolts & nuts etc with provision of charcoal and salt etc all as per elect6rical plate No.3 of SSR part-I 2009 including RCC cover and MS angle iron frame, watering with GI pipe 20 mm dia (medium grade) & MS funnel, concrete pit including excavation and earthwork in any strata and testing on completion etc. complete all as specified and directed. |
AI Tender Summary
Tender Timeline
Mar 22, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedApr 09, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 11, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender