|
| 1 | Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in hard/ dence soil all as specified. |
| 2 | M&L for 75 mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in subbase all as specified. |
| 3 | M&L for 80 mm thick factory made chemferd edge cement concrete paver block of M-30 grade with approved colour design & pattern as in footpath park,low,drive ways of right traffic parking etc of required strength thikness of size / shape made by table vibratory method using PU mould laid in required colour & pattern over and including 50 mm thick compected bed course sand compecting and proper embeding / laying bedding layer paver block in to the sand bedding layer through vibratory compection by using plate vibrator filling the joint with fine sand and cutting of paver block as per required size and pattern finishing and sweeping extra sand complete all as specified. |
| 4 | M&Lfor providing precast kerb stone of size 0.45 x 0.33 x 0.12m in plain cement concrete 1:2:4 type B1 using 20 mm graded stone aggegate set in cement mortar 1:4 all as specified and directed. |
| 5 | Excavation in trenches, n.exc 1.50m wide and n.exc 1.50m in depth for fondation, etc or for shaft, wells, cesspits, man hole, pier holes etc. n.exc 10sqm on plan and n.exc 1.50m in depth and getting out in hard/dense soil |
| 6 | M&L for plain cement concrete 1:4:8 typeD-2 using 40 mm graded stone aggrigate in foundation and mass concrete all as specified. |
| 7 | M&L for Brick work withfly ash old size bricksstraight or curved on plan exc. 6m mean radiusetc. built in CM 1:6 complete all as specified and as directed |
| 8 | M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter all as specified. |
| 9 | M&L RCC M-30 design mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete all as specified. |
| 10 | M & L for use & waste Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all asspecified and as directed |
| 11 | M&L RCC M-30 design mix as in Columns, pillars, piers, posts and struts all as specified. |
| 12 | S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 13 | Ditto but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders |
| 14 | Returning filling with in hard/dense soil, including spreading, levelling, watering and well ramming in layer n.exc. 25 cm thick all as specified. |
| 15 | .Removal excavated surplus soil to a distance n.exc. 50 m and depositing where directed at level n.exc. 1.5 m above the starting point all as directed. |
| 16 | M&L forseprading and leveling in excavated materialfilling in floors or pavings,laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering etc., complete all as specified and as directed |
| 17 | S&F reinforced concerete pipes class NP-2laid and jointed with complete with collors of 450 mm dia all as specified. |
| 18 | M & L for concerete bed to drain pipes in plain cement concrte 1:4:8, type D2 using 40mm graded stone aggregate including packing under and completely surrounding pipes with concerete after they are laid and tested in 450mm dia pipe all as specified. |
| 19 | M & L 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified. |
| 20 | M&L for applyingthree coats of white wash incl preparation of newly plastered wall surfaces etc all as specified. |
| 21 | M & L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in coping including form work all as specified and directed. |
| 22 | M&L 20 mm thick Granite(of any type) work(polished for wall lining)12 mm thick cement motar 1:3 and pointing with white cement (1:2) using marble dust with admixyure of pigment with shade of granite all as specified. |
| 23 | S & F frame work such as grills , gratings etc with ends of bars shoulderd and / or rivetted or forged into spikes framed guard bars barred iron doors landing railings frame works of ways railing framework of door and includig plain sheetetc confirming to FE 290 GDE E-165 all as specified. |
| 24 | M&L for two coat of synthetic enamel paint over one coat ofprimer on newly prepared steel surfaces over 10cm in width or girth not otherwise described all as specified. |
| 25 | Material and labour for 150 mm thich concrete floring with RMC M-25 Grade concrete using vaccume dewatering method laid in alternate bays including steel formwork of MS channel section and depth equal to thikness of concrete floor with vaccum flot to obtain level joint filled with sealing compound including prepring of old surface applying cement sulay 3kg /10 sqm all as specified and as directed all as specified. |
| 26 | supply only metallic floor hardner for wearproof tooping @ 1.00kg/ Sqm |
| 27 | M&L for forming 12 mm thick expansion joints filled with pre formed bituminous filler 100mm depth and top 30mm shall be applied with primer and sealed with sealing compound Grade \"B\" all as specified all as specified. |
| 28 | M&L treatinmg the bottom and sides of excavation at the rate of 5 litrs of emulsion per sqaure meter of surfaces area all as specified. |
| 29 | M&L treating the backfill in contact with foundadtion at the rate of 7.5 litres of emulsion per sqaure meter of vertical surfaces (area of the sub structure in contact with backfill to be measured) all as specified. |
| 30 | M&L for fire brickwork in lining to fire place , fluse etc ( other than in chimeny ) set, jointed and pointed in firecaly etc all as specified. |
| 31 | M&L Sand filling under floor or in foundations including levelling watering and consolidation all as specified. |
| 32 | M&L treating the top surfaces of fillied earth at the rate of 5 litres of emulsion per square meter of surfaces all as specified. |
| 33 | M&Lfor 100 mm Plain Cement concrete 1:5:10 type E2 using 40mm graded stone aggregate as in subbase complete all as specified and as directed |
| 34 | M&L for 40 mm Plain Cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in flooring finish even and smooth without using extra cement complete all as specified and as directed. |
| 35 | M&L for 100 mm Plain Cement concrete 1:2:4 type B -1 using 20mm graded stone aggregateas in flooring even and smooth without using extra cement complete all as specified and as directed. |
| 36 | Laying only 15 mm thick wearproof toping as specified(incorporating an approved metallic floor hardner) laid on concrete floors and pavings, and finished even and smooth (except metallic hardner) |
| 37 | supply only metallic floor hardner for wearproof topingall as specified. |
| 38 | Supply only for Bitumen for waterproof and damproof treatments any grade |
| 39 | M&L rendering 15 mm thick on other than fair faces of brick surfaces or concrete surfaces in CM 1:4 and finished surfaces even & fair all as specified |
| 40 | M&L for 5 mm thick cement plaster in CM 1:4 with WPC over 10 mm thick on fair face of brick or concrete surface in CM 1:6 finished even and smooth without using extra cement Note:- Water proofing compound measuredand paid seperately. |
| 41 | Supply only intergral waterproffing compound |
| 42 | M&L Preparing newly plastered wall surfaces and applying three coats of white washing complete all as specified and as directed |
| 43 | S&F 20 mm Wire netting of galvanised steel wire 1.40mm dia fixed with tinned tacks of wire staples fixed with tinned tacks of wire staples complete all as specified and as directed. |
| 44 | S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 45 | S & F Joist, channel, angle, or tee sections, fixed independently, without connection plate, etc. confirming to Fe -410-W (Gde E-250 Quality A) all as specified. |
| 46 | S&F flue pipes of dia 200mm pipe of mild steel sheet, black in suitable lengths as aproved by the E-in Charge fixed in wall |
| 47 | S&F flue pipes of dia 150 mm pipe of mild steel sheet, black in suitable lengths as aproved by the E-in Charge fixed in wall |
| 48 | S&F Cowls (with 3 stays) of dia 200mm, riveted to and inckuding 15cm length of Flue pipes. |
| 49 | S&F Cowls (with 3 stays) of dia 150mm, riveted to and inckuding 15cm length of Flue pipes. |
| 50 | S&F Mild steel palin black sheet in hearths, covering to doors shuuters covering to doors chowkats(Frames) chullah hoods, water tanks, watre troughs, ducts, urinal trough, and funnes etc,, cut to size edges beads if directed, holes, punched, including round headed screws, clouts nail or rivets and fixed to wod or steel members etc,, with plain 40 mm lap joint or welded / riveted including bending turning up, mitred angles, stopped bends outlets etc,, as required |
| 51 | M&L prepared of newly prepared steel surfaces of any descrption over 10 cm in width or grith, not otherwise described with one coat of red oxide primer overtwo coats of synthetic enamel paint complete all as specified and as directed |
| 52 | M&L Mild steel sliding steel bolt, plates type stove enamelled black with bolt not less than mm dia with and including a minimum ofblots and nuts four on blot plates and two on staples platre and fixed |
| 53 | Supply, install, testing and commissioning of Small Arms Ammunition Burning Unit (SAABU) incinerator suitable for Small Arms Ammunition disposal having three parts vis-à-vis Burning chamber 60cmx60cmx45cm made up of 10mm thick SS310 Grade sheet with a cover made of same material and having 8mm dia multiple holes for escape of gas while burning and galvanized MS tray of size 90cm x 90cm x 2.5cm for ash collection, Fuel unit to be connected via a GI pipe and control unit consists of a long handle arranged out side of the room for tilt the chamber for emptying content into ash tray all as specified and directed. Note:- (a) SAABU incinarator of above specification may not be available in open market as such the same is to be used for defence purpose only.(b)Tenderer may approach the vendor through dept/ AF authority for procurement of the SAABU incinerator. |
| 54 | Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded copper conductor drawn through and including non-matallic rigid PVC conduit PVC conduit fittings and conduit asccessorries concealed in walls, roofs and floors etc., including suitable boxesswitches concealed in walls, roof and socket / electronics fan regulator / telphone socket,including provision of 1.5 sqmm PVC insulated unsheathed cable with multi stranded copper conductor as earth continmuity conductor and connecting to common earth dolly all as specified for:- |
| 55 | One light point controlled by oneswitch |
| 56 | One Exhaust fan point controlled by one switch |
| 57 | One switch socket outlet 3 pin 5 Amps on independent board |
| 58 | S&F Switch piano flush type, single pole,5 Amps, 240 volts |
| 59 | S&F Switch socket 3 pin 5 amps , multi pin , flush type, |
| 60 | S&F ceiling rose 65 X 50 mm , three terminals ,bakelite ,surface. |
| 61 | Supply and fixSurface and wall mounted LED tube light fitting 20W,decorative ultra slim polycarbonate housing LED lightning fixture with high lumen output,environmental friendly energy efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories, suitable for operation on AC, single phase 220 / 230 Volts , 50 Hz supply including taking down old fittings complete all as specified.Make :- Havells:- LHEXACP7IN1W020 / Crompton :- LDL-20-CDL /Bajaj :-BCLSB 20 WH |
| 62 | S&F MCB DB SPN 4 way, doubledoor, powder coated, 240 volts, AC, 50Hz, IP 43 protected, with provision for MCBdouble pole as incomer andSP MCBs as outgoing with tinned copper bus bar, neutral link, earth linkand connecting up complete all as specified and as directed. Note : Incomingand Outgoing MCB measured separately relevent items. |
| 63 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified. Make: Crompton, Havells, Usha |
| 64 | S&F 240V,10KA,\"C\" curve MCB 5 to 32A Single Pole |
| 65 | S&F 240V,10KA,\"C\" curve MCB32A Single Pole Neutral |
| 66 | Supply and fix air circulator fans 230 volts single phase oscilating 450mm sweep suitable for wallmounting all as specified.Make: Usha, Crompton, Havells. |
| 67 | M&L for wiring for circuit / power/sub main with two runs of single core 6 Sqmm size and one run of single core 6.00 Sqmm (green colour as earth continuity conductor) PVC insulated, unsheathed, muilti stranded copper conductor FRLSH cable drawn through and including PVC conduit suitabledia for6.00 sqmm submain wiringwith complete fixing accessories complete all as specified. |
