Supplying And Fixing Of Workstation Tables For Various Office Sections In Old Administration Block At Main Campus. Supplying And Fixing Of Workstation Tables For Various Office Sections In Old Administration Block At Main Campus. , Workstations Table Top, Srinagar-Jammu And Kashmir

Supplying And Fixing Of Workstation Tables For Various Office Sections In Old Administration Block At Main Campus. Supplying And Fixing Of Workstation Tables For Various Office Sections In Old Administration Block At Main Campus. , Workstations Table Top: The Workstationtop Shall Be Made Of 25Mm Thick Prelaminated Particle Board Of Size 1200X600x750mm ( As Per Is: 12823 ) . Bottom Of The Worktop Shall Have A Backing Laminate Of Minimum 0.6Mm Thickness. All The Edges Of Work Surface Shall Be Provided With Machine Pressed 2 Mm Thick Pvc Edge Band Glued With Hotmelt Eva Glueto Maintain Softness And Flexibility, Clarity And Gloss, Barrier Properties, Low-Temperature Toughness, And Resistance To Uv Radiation. The Worktop Should Be Supported By A Worksurface Bracket Made Up Of 2.0 Mm Thick Crca Grade D Steel As Per Is : 513-19 Partition Systems:- Providing And Fixing Of Panel Based System Of 50-60 Mm Thick Of 1200Mm Height. The Panel Should Comprise Of Vertical And Horizontal Extrusions Of Aluminumhaving Material Al96063-T6 And Shouldhave Average Wall Thickness Of 1.2 Mm & Powder Coated With Epoxy-Polyester Powder With Average 50 To 60 Micron Thickness. Bottom Frame For Panel Should Comprise Of L- Channels Made Of 2Mm Thick Crca Steel ( Is:513 ) , Formed Plates Of 3Mm Thick Hr Steel ( Is:2062 ) & Erw Steel Tube Of Size 35X15x1.6Mm In Oval Cross Section ( Is:7138 ) Welded Together. The Same Shall Have Tobe Bolted To The Uprights With Suitable Screws.The Panel Should Be Supported On Legs 120-130Mm High Fabricated Out Of Ms Tube Of Section Of Size Between 30 To 40Mm Of Minimum Thickness Of 1.5Mm ( Is: 7138 Erw Tube ) With The Base Plate Of The Ms Plate As Per Tube Size Over Which A Leveler Shall Be Fitted, Which Allows For Adjustment Of The Height Upto 50Mm. The Top And End Trims Should Be Powder Coated Aluminium Slide Fitted With The Help Of End Trim Connectors. All 2 Way, 3 Way And 4 Ways Junction To Be Covered With Die Cast Aluminum Caps Having Material Al96063-T6 And Shouldhave Average Wall Thickness Of 1.2 Mm. Wire Management : The Cables Shall Come From Ground In A Concealed Conduit / Raceway . System Offered Should Have Provision To Provide The Switch Cut Outs On The Top Tile Above The Worktop Or On The Bottom Tile Of The Panel. 8 Module ( Including 2 Plug ) And 6 Module With Lan To Be Fitted Either Above Worktop Or Below.The Product Quoted Should Be Bifma Level 3 Certified. , Blocks : Theblock For Panel’Sshall Comprise Of 35-40 Mm Thick Paper Honeycomb Or Any Other Filler For Compressed Strength With 3-6Mm Mdf On Each Sides And 0.6Mm Decorative Laminate Or Fabric On Both Sides. Particle Board Framing Shall Be Used On Outer Boundary Of These Blocks As Well As Intermediately At Certain Locations Forming Conduit For Passing Cables. The Blocks Should Be Fixed Into The Supporting Frame Befor Fixing Of The Horizontal And Vertical Trims Which Should Not Be Used As Structural Members.The Top Panels Should Be Offered In Fabric , Fabric Tackable , Metal, White Board . Fabric Shall Be Upholtered With Zero Voc Content Glue As Per Drawing With Fabric Of Approved Quality. White Board Tiles Shall Be Made Of 8.0 Mm Thick Particle Board Conforming To Is: 12823 Laminated With 0.6Mm Thick White Glossy High Pressure Laminate On Outer Side With 0.6Mm Backing Laminate On Inner Surface And Will Behaving All Its Edges With Minimum 0.5 Mm Thick Pvc Edging.The Panel Between 2 Adjacent Seats Shall Be Made Up Of 20-30Mm Thickness. These Intermediate Panels Shall Be Offered In Fabric , Fabric Tackable , Metal Or As Desired By Engineer - In - Charge.The Bottom Panel Shall Be Metal With Provision Of Passing Cables And Cutouts For Switch Boxes At Suitable Locations To The Satisfaction Of The Engineer - In - Charge. The Product Quoted Should Be Bifma Level 3 Certified. Pedestal : The Pedestal Should Be Fixed With Screws To The Worktop Bottom Through Top Stiffners.The Leg Assembly Should Be Fabricated By Co2 Welding Vertical Ms Tubes Of Section 38Mm X 25Mm ( Is 7138 Erw Tube, 38 Mm X 25 Mm X 16 Bg ) Inside Which Leveler Holder Plates Of Size 34 X 21 X 5 Mm ( Is :2062, 5 Mm Hr ) Are Welded With Horizontal Bottom Channel Made Of 2.0 Mm Thick M.S Crca Grade D As Per Is 513. The Height Of The Pedestal Should Be600mm Without Leg Assembly And 720 Mm Including Leg Assembly.Cpu Trolley : Metal Cpu Trolley To Be Provided For Each User Made Of 0.7Mm Crca Sheet Duly Powdercoated With 50Mm Microns Having Adjustable Sides And Nylon Lockable Castors. Key Board Tray : Metal Powder Coated Key Board Tray To Be Provided For Each User Made Of 0.7Mm Crca Sheet Duly Powdercoated With 50Mm Microns With Telescopic Channels. The Product Quoted Should Be Bifma Level 3 Certified. , Manager Table With Side Credenza Main Table Of Size 1500W X 750D X 750H Shall Be Made Of 25Mm Thick Laminated Particle Board Having Pvc Edge Banding On The Edges .Table Top Shall Be Supported Over Powder Coated Aluminium Legs And 18Mm Modesty Panel Made Of Laminated Particle Board With Pvc Edge Band.Wire Management :Ms-Powder Coatedwire Tray With 16 Amp Switch Plate 150D / 300D*120H Below The Table Top On Table Top Is Considered. Side Unit Of Size 900D X 450D X 750H Shall Be Low Height Storage Consisting Of Sliding Shutter And Single Shelf At Middle. Shutters Shall Be Made Up Of 18Mm Laminated Particle Board With Pvc Edge Banding. Shelves Are To Be Made Of 18Mm Prelaminated Particle Board With Pvc Edge Band. Handles Shall Be Stainless Steel Finish In C Shape. Shutters Is To Be Provided With Quality Locks. Pedestal : Free Standing Pedestal Of Size 400 ( L ) X 450 ( D ) X 680 ( H ) Mm With 3 Drawer ( 2 File + 1 Box ) Configration In 18Mm Laminated Particle Board Body And Facia, Including Central Locking, As Per Approved Shades. All The Exposed Edges Shall Be Sealed With Hot Melted Pvc Edge Band Tape. All 3 Drawers Shall Be Fitted With Telescopic Channels, Inside Of Drawer Shall Be Metal Powder Coated . Handles Of The Pedastals Shall Be In Stainless Steel Finish. Levellors Shall Be Provided Having Adjustment Up To 15Mm.The Above Mentionedfurniture Should Be As Per Specification And Sample Approved By Client.Godrej, Wipro, Monarch Or Equivelent , Supplying And Placing Of High Back Chairs. Seat / Back Assembly: The Seat / Back Are To Be Made Up Of 1.2 Cm Thick Hot Pressed Plywood, Upholstered With Leatherite And Moulded Polyurethane Foam Together. The Back Foam Shall Be Designed With Contoured Lumbar Support For Extra Comfort. ( High Back ) Size: 500Mm. ( W ) X 700Mm. ( H ) . Seat Size: 500Mm. ( W ) X 480Mm. ( D ) . Polyurethane Foam: The Polyurethane Foam Shall Be Moulded With Density = 45 + / -2 Kg / M3 And Hardness = 20 + / - 2 On Hampden Machine At 25% Compression. Armrests: The One-Piece Armrests Shall Be Soft Pu Arms In Leatherite Finish. The Armrests Are To Be Scratch And Weather Resistant.The Chair Shall Be Provided With Synchro Knee Tilt With Multi Angle Locking Mechanism Having 360°- Swivel Mechanism. The Pneumatic Height Adjustment Shall Have An Adjustment Stroke Of 90 Mm. The Bellow Shall Be 3-Piece Telescopic Type And Shall Be Injection Moulded In Black Polypropylene.The Pedestal Shall Be Five Prong Metallic Silver Finish Fitted With 5 Nos Twin Wheel Castors. The Pedestal Shall Be 660Mm. Pitch Center Dia. ( 770 Mm With Castors ) .The Twin Wheel Castors Are Nylon. The Above Mentionedfurniture Should Be As Per Specification And Sample Approved By Client. , Furniture Senior Manager Table With Side Credenza Main Table Of Size 2400W X 900D X 750H Shall Be Made Of 25Mm Thick Laminated Particle Board Having Pvc Edge Banding On The Edges .Table Top Shall Be Supported Over Powder Coated Aluminium Legs And 18Mm Modesty Panel Made Of Laminated Particle Board With Pvc Edge Band. Side Unit Of Size 900D X 450D X 750H Shall Be Low Height Storage Consisting Of Sliding Shutter And Single Shelf At Middle. Shutters Shall Be Made Up Of 18Mm Laminated Particle Board With Pvc Edge Banding. Shelves Are To Be Made Of 18Mm Prelaminated Particle Board With Pvc Edge Band. Handles Shall Be Stainless Steel Finish In C Shape. Shutters Is To Be Provided With Quality Locks. Pedestal : Free Standing Pedestal Of Size 400 ( L ) X 450 ( D ) X 680 ( H ) Mm With 3 Drawer ( 2 File + 1 Box ) Configration In 18Mm Laminated Particle Board Body And Facia, Including Central Locking, As Per Approved Shades. All The Exposed Edges Shall Be Sealed With Hot Melted Pvc Edge Band Tape. All 3 Drawers Shall Be Fitted With Telescopic Channels, Inside Of Drawer Shall Be Metal Powder Coated . Handles Of The Pedastals Shall Be In Stainless Steel Finish. Levellors Shall Be Provided Having Adjustment Up To 15Mm.The Above Mentionedfurniture Should Be As Per Specification And Sample Approved By Client.

INR 1100 /-

Refer document

INR 45.39 Lakhs /-

Name of Work: Supplying and fixing of Workstation Tables for Various Office Sections in Old Administration Block (Advertised cost Rs. 45.39 Lacs)

Sl. No.	Item Description
1	WORKSTATIONS TABLE TOP: The workstationtop shall be made of 25mm thick prelaminated particle board of size 1200x600x750mm (As per IS: 12823). Bottom of the worktop shall have a backing laminate of minimum 0.6mm thickness. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC Edge band glued with hotmelt EVA glueto maintain softness and flexibility, clarity and gloss, barrier properties, low-temperature toughness, and resistance to UV radiation. The worktop should be supported by a worksurface bracket made up of 2.0 mm thick CRCA grade D steel as per IS : 513-19 Partition Systems:- Providing and fixing of panel based System of 50-60 mm thick of 1200mm height. The panel should comprise of vertical and horizontal extrusions of aluminumhaving material AL96063-T6 and shouldhave average wall thickness of 1.2 mm & powder coated with epoxy-polyester powder with average 50 to 60 micron thickness. Bottom frame for panel should comprise of L- Channels made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together. The same shall have tobe bolted to the uprights with suitable screws.The panel should be supported on legs 120-130mm high fabricated out of MS Tube of section of size between 30 to 40mm of minimum thickness of 1.5mm(IS: 7138 ERW Tube) with the base plate of the MS plate as per tube size over which a Leveler shall be fitted, which allows for adjustment of the height upto 50mm. The top and end trims should be powder coated aluminium slide fitted with the help of end trim connectors. All 2 way, 3 way and 4 ways junction to be covered with die cast aluminum caps having material AL96063-T6 and shouldhave average wall thickness of 1.2 mm. Wire Management : The cables shall come from Ground in a concealed conduit / raceway . System offered should have provision to provide the switch cut outs on the top tile above the worktop or on the bottom tile of the panel. 8 module (including 2 plug) and 6 module with lan to be fitted either above worktop or below.The product quoted should be BIFMA level 3 certified.
2	BLOCKS : Theblock for panel’sshall comprise of 35-40 mm thick paper honeycomb or any other filler for compressed strength with 3-6mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Particle board framing shall be used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. The blocks should be fixed into the supporting frame befor fixing of the horizontal and vertical trims which should not be used as structural members.The top panels should be offered in fabric , fabric tackable , metal, white board . Fabric shall be upholtered with zero VOC content glue as per drawing with fabric of approved quality. White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.6mm thick white glossy high pressure laminate on outer side with 0.6mm backing laminate on inner surface and will behaving all its edges with minimum 0.5 mm thick PVC edging.The Panel between 2 adjacent seats shall be made up of 20-30mm thickness. These intermediate panels shall be offered in fabric , fabric tackable ,metal or as desired by Engineer - in - charge.The bottom panel shall be metal with provision of passing cables and cutouts for switch boxes at suitable locations to the satisfaction of the Engineer - in - charge. The product quoted should be BIFMA level 3 certified. PEDESTAL : The Pedestal should be fixed with Screws to the worktop bottom through top stiffners.The leg assembly should be fabricated by CO2 welding vertical MS tubes of section 38mm X 25mm ( IS 7138 ERW Tube, 38 mm X 25 mm X 16 bg) inside which leveler holder plates of size 34 X 21 X 5 mm ( IS :2062, 5 mm HR) are welded with horizontal bottom channel made of 2.0 mm thick M.S CRCA grade D as per IS 513. The Height of the pedestal should be600mm without leg assembly and 720 mm including leg assembly.CPU Trolley : Metal CPU trolley to be provided for each user made of 0.7mm CRCA sheet duly powdercoated with 50mm microns having adjustable sides and nylon lockable castors. KEY BOARD TRAY : Metal Powder Coated Key Board Tray to be provided for each user made of 0.7mm CRCA sheet duly powdercoated with 50mm microns with telescopic channels. The product quoted should be BIFMA level 3 certified.
3	MANAGER TABLE WITH SIDE CREDENZA Main Table of size 1500W X 750D X 750H shall be made of 25mm thick laminated particle board having PVC edge banding on the edges .Table top shall be supported over powder coated aluminium legs and 18mm modesty panel made of laminated particle board with pvc edge band.WIRE MANAGEMENT :MS-POWDER COATEDwire tray WITH 16 amp switch plate 150D/300D*120H below the table top on table top is considered. Side unit of size 900D X 450D X 750H shall be low height storage consisting of Sliding Shutter and single shelf at middle. Shutters shall be made up of 18mm laminated particle board with pvc edge banding. Shelves are to be made of 18mm prelaminated particle board with pvc edge band. Handles shall be Stainless Steel finish in C Shape. Shutters is to be provided with quality locks. Pedestal : Free standing pedestal of size 400(L) x 450(D) x 680(H)mm with 3 drawer (2 file + 1 box ) configration in 18mm laminated particle board body and facia, including central locking, as per approved shades. All the exposed edges shall be sealed with hot melted PVC edge band tape. All 3 drawers shall be fitted with telescopic channels, Inside of drawer shall be metal powder coated . Handles of the pedastals shall be in stainless steel finish. Levellors shall be provided having adjustment up to 15mm.The above mentionedfurniture should be as per specification and sample approved by client.Godrej,wipro,monarch or equivelent
4	Supplying and placing of High Back Chairs. SEAT/BACK ASSEMBLY: The seat / back are to be made up of 1.2 cm thick hot pressed plywood, upholstered with Leatherite and moulded Polyurethane foam together. The back foam shall be designed with contoured lumbar support for extra comfort. (HIGH BACK) SIZE: 500mm. (W) X 700mm. (H). SEAT SIZE: 500mm. (W) X 480mm. (D). POLYURETHANE FOAM: The Polyurethane foam shall be moulded with density = 45 +/-2 kg/m3 and Hardness = 20 +/- 2 on Hampden machine at 25% compression. ARMRESTS: The one-piece armrests shall be soft PU arms in leatherite finish. The armrests are to be scratch and weather resistant.The chair shall be provided with Synchro knee tilt with multi angle Locking Mechanism having 360°- swivel mechanism. The pneumatic height adjustment shall have an adjustment stroke of 90 mm. The bellow shall be 3-piece telescopic type and shall be injection moulded in black Polypropylene.The pedestal shall be five prong metallic silver finish fitted with 5 nos twin wheel castors. The pedestal shall be 660mm. Pitch center dia. (770 mm with castors).The twin wheel castors are Nylon. The above mentionedfurniture should be as per specification and sample approved by client.
5	FURNITURE SENIOR MANAGER TABLE WITH SIDE CREDENZA Main Table of size 2400W X 900D X 750H shall be made of 25mm thick laminated particle board having PVC edge banding on the edges .Table top shall be supported over powder coated aluminium legs and 18mm modesty panel made of laminated particle board with pvc edge band. Side unit of size 900D X 450D X 750H shall be low height storage consisting of Sliding Shutter and single shelf at middle. Shutters shall be made up of 18mm laminated particle board with pvc edge banding. Shelves are to be made of 18mm prelaminated particle board with pvc edge band. Handles shall be Stainless Steel finish in C Shape. Shutters is to be provided with quality locks. Pedestal : Free standing pedestal of size 400(L) x 450(D) x 680(H)mm with 3 drawer (2 file + 1 box ) configration in 18mm laminated particle board body and facia, including central locking, as per approved shades. All the exposed edges shall be sealed with hot melted PVC edge band tape. All 3 drawers shall be fitted with telescopic channels, Inside of drawer shall be metal powder coated . Handles of the pedastals shall be in stainless steel finish. Levellors shall be provided having adjustment up to 15mm.The above mentionedfurniture should be as per specification and sample approved by client.