|
| 1 | Extension in first floor |
| 2 | 5.2.2 : Reinforced cement concrete works in walls (any thickness), including attached pilasrers, buttresses, plinth and string courses, fillets, coloumns, pillars, piers,abutments, posts and struts etc.up to floor five level excluding cost of centering, shuttering, finishing and reinforcement: 1:1.5:3(1 Cement : 1.5 coarse sand:3 graded stone aggregate 20mm nominal size)Des.No.LBDColoumn20.6000.2303.000Coloumn120.6000.2303.000 |
| 3 | 6.4.2 : Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in superstructure above plinth level uo to floor V level in all shapes and sizes in : Cement mortar 1:6(1 Cement : 6 Coarse Sand) Des. No.LB D First floor 2 17.540 0.2303.200 First floor 2 9.460 0.2303.200 For lift2 1.500 0.2307.000For lift1 1.800 0.2307.000W 8 1.500 1.5000.200 Ramp door 1 2.400 1.5000.200d 11.0002.1000.200 |
| 4 | 13.1.212mm cement plaster of mix 1:6 (1 Cement : 6 fine sand)Des.No.LBDFirst Floor 2*2 17.540 3.000 First Floor 2*2 9.460 3.000lift14.800 7.000lift15.260 7.000 W 8*2 1.500 1.500ramp door1*2 1.500 2.200d 1*2 1.0002.100 |
| 5 | 13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @2.20 kg/10 sqm)Des.No.LBDramp16.000 2.200 ramp2*2 6.0000.450 First floor 2*2 17.540 3.000 Firstfloor 2*29.460 3.000 Lift14.8007.000 Lift15.2607.000w8*2 1.500 1.500 ramp door1*21.5002.200d 1*21.0002.100 |
| 6 | 5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work p to plinth level : 1:1.5:3 (1 Cement 1.5 coarse sand: 3 graded stone aggregrate 20 mm nominal size)Des.No.L BD ramp 1 6.000 2.2000.150 beam2 6.000 0.2000.450Lintel2 9.900 0.2000.150 Lintel1 18.500 0.2000.150Shade2 10.500(0.1+0.75/2)0.600 Shade1 18.500(0.1+0.75/2) 0.600 Lift beam14.800 0.230 0.550Roof 12.000 2.200 0.120 |
| 7 | 5.9.5 Centering and shuttering including strutting,etc. and removal of form for Lintels, beams, Plinth beams, gridders bressumers and cantilevers Des. No.LBRamp16.000 2.200 Beam 2*26.000 0.450 |
| 8 | 5.9.6 Centering and shuttering including struttering, etc. and removal of form for : Coloumns, Pillars, Piers, Abutments, Posts and Struts Des.No. LDColoumn 2 1.6603.000 |
| 9 | 5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete u to plinth level thermo- Mechanically treated bars of grade Fe-500 D or more Des. No. CF item no: 11*5.796150.0 item no:51*7.42 100.0 |
| 10 | 13.16.1: 6 mm Cement plaster of mix : 1:3 (1 Cement : 3 Fine Sand) Des. No. LBRamp1 6.0002.200Ramp 2*2 6.0000.450Shade 2 10.5000.600Shade 1 18.5000.600 |
| 11 | 50.10.1 : Steel work in built up GI tubular (Round, Square, Rectangular hollow tubes etc) trusses etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Des No.LCF 80 x 40 9*2 4.500 5.34 Struss 95.000 5.34Struss 92.500 5.34 |
| 12 | 50.10.2 : Steel work for purlin/ single section with GI pipes including cutting , hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. Complete. DesNo.LCF Purlin50x 25 1018.5002.23 |
| 13 | 13.99.1 : Painting with synthetic enamal paint of approvedbrand and manufacture of required colour to give an even shade: One or more coats on old work. DesNo.LCF80 x 40 9*24.5000.24Struss95.0000.24Struss92.5000.24 Purlin-50x2510 18.500 0.15 |
| 14 | 51.20 : Providing and fixing precoated galvanised iro profile sheets (size, shape and pitch of corrugation as approved by Engineer in charge) 0.35 mm (+0.05 %), total thiickness with zinc coating 120 g/sqm as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and Polyster top coat 15-18 microns. Sheets should have protective gauard film of 25 microns minimum to avoide scratches during transportation and should be supplied in single length up to 20 m or as desired by Engineer in charge. The sheet shall be fixed using self drilling/ self tapping screws of size(5.5 x 55mm) with EPDM seal, complete up to any pitch in horizondel/ vertical on curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape where ever required. DesNo.L BCF............. 1 19.50010.900 1.2 |
| 15 | 21.1.1.2 : Providing and fixing aluminium works for doors, windows, ventilators and partitiions with extruted built up standard tubular sections/appropriate Z sections and other sections of approved may confirming to IS: 733 and IS: 1285, fixing with a dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e., at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smmoth, rust free, straight, mitred and jointed mechanicaly where ever required including cleat angle, aluminium snap bending for glazing/ panaling, CP brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer in-charge( Glazing, Panaling and dash fasteners to be paid for seperately): for fixed portion powder coated aluminium (Minimum thickness of powder coating 50 micron) DesNo. L CF W150*1508*21.500 0.85 W150*1508*21.500 0.85Door 1.5*2.4 1*2 2.400 0.85 Door 1.5*2.411.500 0.85 Door 1.2*2.1 1*2 2.100 0.85Door 1.2*2.111.200 0.85 |
| 16 | 21.1.2.2 : for shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings whereever required including the cost of EPDM rubber/ neoprene gasket required. (Fittings shall be paid for seperately). Powder coated aluminium(Minimum thickness of powder coating 50 micron)DesNo.LCFw150*1503*2 1.5000.55 w150*1503*20.500 0.55 door1.5*2.4 1*2 2.400 0.55 door1.5*2.4 2*2 0.750 0.55door1.2*2.1 1*2 2.100 0.55 door1.2*2.12 1.200 0.55 |
| 17 | 21.2.2: Providing and fixing 12mm thick pre- laminatted particle board flat pressed 3 layer or graded wood particle board confirming to IS:12823 Grade I Type II, in panaling fixed in aluminium doors, windows shutters and partition frames with C.P.brass/stainless steel screws etc.Complete as per architectural drawing and directions of Engineer in charge. Pre- laminatted particle board with decorative lamination on both sides.Des. No. LBDoor 11.2000.800 |
| 18 | 21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. withEPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer in cahrge. (Cost of aluminium snap beading shall be paid in basic item): with float glass panes of 4.0 mm thickness. Des. No.L BW 3*8 1.4500.450 |
| 19 | 21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. withEPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer in cahrge. (Cost of aluminium snap beading shall be paid in basic item): with float glass panes of 5.50 mm thickness. Des.No.LB Door1 1.200 1.300 |
| 20 | 21.18 Providing and fixing 12 mm thick frameless toughended glass door shutter of approved brand and manufacture, including providing and fixing top and bottom pivot & spring type fixing arrangement and making necessory holes etc. for fixing required door fittings , all complete as per direction of Engineer in- charge (Door handle, lock & stopper etc to be paid seperately)Des.No.LB Ramp Door20.750 2.400 |
| 21 | 10.6.1: Supplying and fixing rolling shutters of approved make, made for required size MS laths, interlocked together through their entire length and pointed together at the end by end locks, mounded on specialy designed pipe shaft with brackets, side guides and arragements inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessory 27.5 cm long wire springs manufactured from hidh tensile steel wire of adequate strength confirming to IS:4454-Part I & M.S.top cover of required thickness for rolling shutters.80 x 1.25mm M.S laths with 1.25mm thick top cover. Des.No. L B RampD1 1.5002.400 |
| 22 | 9.117.1 : Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm) with wall thickness 2.0mm ( ±0.2mm),corners of the door frame to be joinded with galvanised brackets and stainless steel screws, joins mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanised M.S. tube of size 19 x19mm and 1mm (±0.1mm)wall thickness and 3 Nos. stainless steel hinges fixed to the frame complete as per manufactures specification ad direction of Engineer in - charge extruded section profile size 48 x40mmDes.No. Lggggggggggggggggg1 5.000 |
| 23 | 9.118.1 Providing and fixing to exiting door frames 24mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x 24 mm and wall thickness of 2mm(± 0.2mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S galvanised/ plastic brackets of size75 x 220mm having wall thickness 1.0mm and stainless steel screws. The Styles of the shutter reinforced by inserting galvanised M.S tube of size 20 x20mm and 1mm (±0.1mm) wall thickness. The lock rail made up of \"H\" section , a uPVChollow section of size 100 x 24mm and 2mm(±0.2mm) wall thickness, Fixed to the shutter style by means of plastic/ galvanised M.S.\"U\" cleats. The shutterframe filled with a uPVC multi - chambered single panel of size not less than 620mm, having overall thickness of 20mm and 1mm (±0.1mm) wall thickness. The panals filled vertically and tie bar at to placeses by inserting horizondely 6mm galvanised M.S Rod and fastended with nuts and washers. Complete as per manufactures specifications and direction of Engineer in- charge for WC and bathroom door shutter). Des. No. LB Door1 0.800 2.100 |
| 24 | 11.41.2 Providing and laying vitrified forr tiles in different sizes (thickness to be specified by the manufacturer) with absorption less than 0.08% and confirming ti IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 Cement:4 Pore sand), including grouting the joins with white cement and matching pigments etc. Complte. size of tile 600 x 600 mm Des No.LBRampDo118.000 9.400 |
| 25 | 50.12.5.1 Providing and fixing false selling with e board classic tile or equivalent make of size 610 x610 x4mm ceiling of approved quality in aluminium frame work with necessory screws etc. Complete. (Aluminium frame work shall be paid seperately). Des. No.L B RampDoor118.000 9.400 |
| 26 | 16.89 Providing and laying mat finished rectified tile of size 300 x 300x 9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved mske in all colours and shades in for outdoor floors such as footpath, court yard, multi models location etc., laid on 20mm thick base of cement mortar 1:4 ( 1 Cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer- in- charge. Des. No.LB RampDoor15.800 1.800 |
| 27 | 11.48.2 Grouting the jointts of flooring tiles having joints of 3mm width, using epoxy grout mixx 0.70 kg of organic coated filler of desired shade (0.10 Kg of hardener and 0.20 Kg of resin per kg) including filling/grouting and finishing complete as per direction of Engineer- in- charge. Size of tile 600 x 600 mm. Des.No. LB RampDoor1 18.000 9.400 |
| 28 | 50.9.11.1: Providing and fixing Thomson Multi wood board or equivalent make paneling 12 mm thick, to frame, backing or studding with screws etc. complete (Frames, Backing or studding to be paid seperately) as per the direction of site Engineer- in- charge. Des.No. LB Rack work 153.000 0.500Rack work 2*2 3.000 0.500Rack work12 3.0000.500 |
| 29 | 50.9.11.2: Providing and fixing Thomson Multi wood board or equivalent make paneling 18 mm thick, to frame, backing or studding with screws etc. complete (Frames, Backing or studding to be paid seperately) as per the direction of site Engineer- in- charge. Des.No. LB Rack work 123.000 0.500 |
| 30 | 13.114 : Melamine polishing on wood work (One or more coat). Des.No. LB Rack work 15*2 3.000 0.500 Rack work 12*2*23.000 0.500 Rack work 12*2 3.000 0.500 Rack work 123.000 0.500 |
| 31 | 50.18.8.2.2: Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & firrings with one step PVC solvent cement and testing of joints complete as per direction of Engineer - in- charge. Concealed work, including cutting chases and making good the wall etc.20 mm pipe 10kgf/cm2Des.No.L Rack work 150.000 |
| 32 | 50.18.8.3.1: Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & firrings with one step PVC solvent cement and testing of joints complete as per direction of Engineer - in- charge. Concealed work, including cutting chases and making good the wall etc.25 mm pipe 12kgf/cm2Des.No.L Rack work 125.000 |
| 33 | 50.18.8.4.1: Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & firrings with one step PVC solvent cement and testing of joints complete as per direction of Engineer - in- charge. Concealed work, including cutting chases and making good the wall etc.32 mm pipe 10kgf/cm2Des.No. L Rack work130.000 |
| 34 | 50.18.8.5.1: Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & firrings with one step PVC solvent cement and testing of joints complete as per direction of Engineer - in- charge. Concealed work, including cutting chases and making good the wall etc.40 mm pipe 10kgf/cm2Des.No. L Rack work 110.000 |
| 35 | 50.18.8.7.1: Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & firrings with one step PVC solvent cement and testing of joints complete as per direction of Engineer - in- charge. Concealed work, including cutting chases and making good the wall etc.63 mm pipe 6kgf/cm2Des.No. L Rack work 1 3.000 |
| 36 | 50.18.8.8.1: Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & firrings with one step PVC solvent cement and testing of joints complete as per direction of Engineer - in- charge. Concealed work, including cutting chases and making good the wall etc.75 mm pipe 6kgf/cm2Des.No. L Rack work 1 10.000 |
| 37 | 50.18.8.9.1: Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & firrings with one step PVC solvent cement and testing of joints complete as per direction of Engineer - in- charge. Concealed work, including cutting chases and making good the wall etc.110 mm pipe 6kgf/cm2Des.No. L Rack work 1 15.000 |
| 38 | 51.19.ST4 : Supplying and installing ready made PVC Septic tanks including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid seperately)4.35 to 50 flush capacity. Des.No. Rack work 1 |
