|
| 1 | Providing and fixingG.I. pipes of medium class as per IS:1239 with latest amendment complete with G.I. fittings and clamps, including ctting and making good the walls etc. complete as per CPWD specification and direction of the Engineer-in-Charge. Internal work - Exposed on wall. |
| 2 | a) 15 mm dia. nominal bore |
| 3 | b) 20 mm dia. nominal bore |
| 4 | C)25 mm dia. nominal bore |
| 5 | d) 40 mm dia. nominal bore |
| 6 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :i)25 to 40 mm nominal bore |
| 7 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : |
| 8 | a) 15 mm nominal bore |
| 9 | b)20 mm nominal bore |
| 10 | C) 25 mm nominal bore |
| 11 | d) 40 mm nominal bore |
| 12 | Providing and fixing G.I. pipe fittings of approved quality (1st Marked) as per direction of the Engineer-in-Charge. |
| 13 | A) G.I. Nipple (G.I.) |
| 14 | i) 15mm dia 75mm long |
| 15 | ii15mm dia 150mm long |
| 16 | iii) 20mm dia 75mm long |
| 17 | iv) 20mm dia 150mm long |
| 18 | v) 25mm dia 75mm long |
| 19 | vi) 25mm dia 150mm long |
| 20 | B) G.I. Socket |
| 21 | i) 15mm dia |
| 22 | ii)) 25mm dia |
| 23 | C) Elbow |
| 24 | i) 15mm dia |
| 25 | ii)25mm dia |
| 26 | D) G.I. Tee |
| 27 | i) 25x25x25 mm dia |
| 28 | Cleaning and washing of G.I. pipe line 15-50mm nominal bore (internal )using pump machine G.I. wire or bamboo etc. after cleaning the pipe line from the work & taking out union joint socket , elbow etc. and refitting the same including trial runper direction of Engineer-in-Charge. |
| 29 | Providing and fixing brass fullway with wheel valve of approved quality.a) 40mm nominal bore (TSR-02) |
| 30 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 i)15 mm nominal bore |
| 31 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.i)15 mm nominal bore. |
| 32 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931i)15 mm nominal bore |
| 33 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. )15mm nominal bore. |
| 34 | Providing and fixing C.P. brass pillar cock of approved quality ( ESSCO /ROYAL/PUSHP or Equirement)i) 15 mm nominal bore. |
| 35 | Providing and fixing uplasticised PVC connection pipe with brass unions :A)30 cm lengthi)15 mm nominal bore |
| 36 | ProvidingandfixingonwallfaceunplasticisedRigidPVCrainwater pipes (working pressure 4 kg / cm2)conformingto IS : 13592 Type Aincludingjointingwith sealring conformingtoIS:5382leaving10mmgapforthermalexpansion: |
| 37 | i)Single socketed pipe - 75 mm OD |
| 38 | ii)Single socketed pipe - 110 mm OD |
| 39 | Providingandfixing on wallface unplasticised - PVCmouldedfittings/ accessoriesfor unplasticised Rigid PVC rain water pipes conforming to IS:13592TypeAincludingjointingwith sealringconformingtoIS: 5382 leaving 10 mm gap forthermalexpansion: |
| 40 | A) Coupler |
| 41 | i) 75 mm |
| 42 | i) 100 mm |
| 43 | B) Single equal tee with door |
| 44 | i) 75x75x75mm |
| 45 | ii) 110x110x110mm |
| 46 | C)Bend 87.5° |
| 47 | i) 75 mm |
| 48 | i) 110mm |
| 49 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVCrainwater pipesbymeansof50x50x50mmhard woodplugs,screwedwithM.S.screwsofrequiredlengthincluding cutting brick work andfixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. |
| 50 | i) 75mm |
| 51 | ii) 110mm |
| 52 | Washing and clearing white vitreous china Orissa Pattern W.C.pan ,Padestal type water closet( European type W.C.Pan ) ,urinal basin , Wash basin & laboratory Sink etc. at any floor using Acid , Harpic & brushes etc. as per direction of the Engineer-in-Charge. |
| 53 | Clearing & washing of blockage W.C.Pan including line, wash basin line, urinal line and sink line etc. (Using G.I. wire & bamboo ,Acid & Harpic etc.) as per direction of the Engineer-in-Charge. |
| 54 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings: i) Flat back wash basin of size 630x450mm. |
| 55 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipei)32 mm dia |
| 56 | Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required :i)White glazed fire clay kitchen sink of size 600x450x250 mm. |
| 57 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. i)10 litre capacity-White |
| 58 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 59 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 60 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : i) Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 61 | Providing and fixing ball valve (brass) of approved qualityHigh or Low pressure, with plastic floats complete:- |
| 62 | i)15 mm nominal bore |
| 63 | ii)20 mm nominal bore |
| 64 | iii) 25 mm nominal bore |
| 65 | Renewing glass panes and refixing existing wooden fillets:i) Floatglass panes of thickness 4 mm . |
| 66 | Providing and fixing PTMT Waste Coupling for washbasin and sink, of approved quality and colour. |
| 67 | a) Waste coupling 3.1 mm of 79mm length and 62mm breadth weighing not less than 45 gms. |
| 68 | b) Waste coupling 38mm of 83mm length and 77mm breadth, weighing not less than 60gms. |
| 69 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved 450mm long towel rail with total length of 495mm, 78mm wide and effective height quality and colour.a) 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. |
| 70 | Providing and fixing PVC bib cock of approved quality (PVC) i) 15mm nominal bore |
| 71 | Labour charge for repairing of PVC cistern as directed by the Engineer-in-Charge. |
| 72 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge. |
| 73 | 12 mm cement plaster of mixi)In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 74 | 15 mm cement plaster of mixi) In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 75 | First class brick work in foundation and plinth including cost of all materials as required complete:- i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 76 | Half brick masonry work with first class bricks in foundation upto floor five level including cost of all materials as required complete:- i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 77 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :i) 300x16 mm |
| 78 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 79 | i)250x10 mm |
| 80 | ii) 150x10 mm |
| 81 | iii) 100x10 mm |
| 82 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :i)125 mm |
| 83 | Providing & fixing of surgical tap of approved quality as per direction of Engineer-in-Chargei) 15 mm nominal bore. |
| 84 | Providing & fixing C.P. brass waste as per clause of chapter 19 of CPWD specification. i) 32mm dia |
| 85 | Providing & fixing C.P. brass 32 mm bottle toap of approved quality (ISI marked) as per direction of the Engineer-in-Charge.a) 15mm nominal bore |
| 86 | Providing & fixing C.P. brass three-in-one wall mixer of approved quality (ISI marked) as per direction of the Engineerin-Charge.a) 15mm nominal bore |
| 87 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :White solid plastic seat with lid |
| 88 | Internal wearing for panel board of pump house including fitting fixing wooden board switch, holder, bulb & wire etc. |
| 89 | Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc complete (New Work) |
| 90 | i) 15mm nominal bore |
| 91 | ii) 20mm nominal bore |
| 92 | iii) 25mm nominal bore |
| 93 | iv) 40mm nominal bore |
| 94 | Providing and fixing PTMT grating of approved quality and colour. i) 125mm nominal dia with 25mm waste hole. |
| 95 | Cutting holes upto 30x30cm in walls including making good the samei) With 1st Class bricks. |
| 96 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shutteringAll work upto plinth level |
| 97 | I) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burntbrick aggregate 40 mm nominal size) |
| 98 | II) 1:4:8 ( 1 Cement: 4 fine sand : 8 graded well burnt brick aggregate 40 mm nominal size) |
| 99 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- I) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 100 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:-I) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 101 | Neat cement punning. |
| 102 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture, of required shade and colour complete, as per manufacurer\"s specification. [Payment shall be made after submission of Test Certificate issued by the Manufacturer] |
| 103 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 104 | Providingandfixingaluminiumworkfordoors,windows,ventilators, Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :-A. For fixed portion of approved quality:- |
| 105 | i) Anodisedaluminium(anodisedtransparentordyedto requiredshadeaccordingtoIS:1868,Minimumanodic coating of grade AC 15). |
| 106 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- |
| 107 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 108 | Supplying and installation of Kiriliskar make 2HP monobloc (2\"x1½\" suction and delivery) pump set with necessary fittings complete as per direction of the Engineer-in-Charge |
