Installation Of K.Jamankira-Vii Rl Project Under Kuchinda Block In Sambalpur District Installation Of K.Jamankira-Vii Rl Project Under Kuchinda Block In Sambalpur District
Tender Value
73.78 Lakhs
Estimated cost
Bid Submission
16 Mar 2022
0 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kuchinda → Odisha
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Installation Of K.Jamankira-Vii Rl Project Under Kuchinda Block In Sambalpur District Installation Of K.Jamankira-Vii Rl Project Under Kuchinda Block In Sambalpur District
BOQ
| Sl. No. | Item Description |
| 1 | Part-A |
| 2 | Earthwork in excavation of foundation in hard soil including dressing & levelling of bed within initial lead of 50mt. & lift of 1.5mtr etc complete as per the direction of the Engineer-incharge. |
| 3 | Filling in foundation & plinth with sand including watering & ramming etc complete as per the direction of the Engineer-incharge. |
| 4 | Cement concrete (1:4:8) with 4cm size h.g.b. crusher broken metal of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc. complete as per the direction of the Engineer-incharge. |
| 5 | Brick work with K.B. Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6)in foundation & plinth complete as per the Engineer-incharge |
| 6 | Brick work with K.B. Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6) insuper structure etc. complete as per the Engineer-incharge |
| 7 | Cement concrete (1:2:4) with 12mm size black h.g.b. crusher broken chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc complete as per the direction of the Engineer-incharge. |
| 8 | Rigid smooth centering & shuttering for R.C.C. works including false work & dismateling then after including cost of materials in ground floor complete an directed by the Engineer-incharge.(a) Roof slab, chajja, carnice etc |
| 9 | (b) Lintel |
| 10 | © Plinth band, foundation, footing base of column etc |
| 11 | (d) Beams & Columns |
| 12 | (e) Walls & fins |
| 13 | Labour charges for MS reinforcement for RCC work including cutting, bending & tying the grills and placing in position including cost of binding wire 18 to 20 gauge & HYSD steel bar ( FE 415/ FE 500 ) |
| 14 | R.C.C. work in C.C. (1:2:4) including hoisting & laying & curring for 28days using 12mm. Size clean black hard granite crusher broken chips of approve quality and from approve quarry including cost taxes conveyance charges of all materials to the worksite with supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 15 | 12mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 16 | Cement punning over plastering including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 17 | 25mm thick AS flooring with CC (1:2:4) using 12mm sizeblack h.g.c.b chips of approved quality from approved quarry including watering and curing with cost, taxes, royality and conveyance charges of all materials to the work site and supply of all labour, T & P required for the work etc. complete |
| 18 | 2.5 cm thick grading concrete (1:2:2) with 6 cm size h.g chips |
| 19 | Cement washing two coats over plastering |
| 20 | Finishing walls with plastic emulsion paint of approved shade on new work two coat to give an even shade excluding cost of paint. |
| 21 | Wall painting two coats with weather coat paint of approved shade excluding cost of paint. |
| 22 | Cost of plastic emulsion paint |
| 23 | Cost of weather coat cement paint |
| 24 | Painting of red oxide primer of approved quality for priming over iron work including cost, taxes etc. complete |
| 25 | Painting of enamel paint of approved quality and colour for painting over iron work including cost, taxes etc. complete |
| 26 | MS panel door double leafed with MS frame overall size of 1.20x1.98 mtr for door and 0.90x0.90 mtr for window, shutter of 20 gauge CR sheet panel as per approved size and specification etc. includingfitting & fixing the door etc. complete |
| 27 | Cost of electrification of the pump chamber. |
| 28 | Writing charge of required information and data on both side of the transperancy pillar including supplying of approved paints and required material for writing etc. complete as per the direction of the Engineer-incharge. |
| 29 | Fitting of un plasticised 200 mm dia meter diaPVC Pipe for all classes including jointing the pipe with solvent cement by non-head application method including fitting and fixing of required no. of PVC Tee for outlet and PVC Shaddle and PVC Riser nipple for fitting air valve, equal Tee etc. including cost of PVC Pipe, cost of Solvent Cement, transportation of Pipe complete including conveyance pipe from village to worksite and testing of pipe line etc. complete as per the direction of the Engineer-incharge. |
| 30 | Fitting of un plasticised 250 mm dia meter diaPVC Pipe for all classes including jointing the pipe with solvent cement by non-head application method including fitting and fixing of required no. of PVC Tee for outlet and PVC Shaddle and PVC Riser nipple for fitting air valve, equal Tee etc. including cost of PVC Pipe, cost of Solvent Cement, transportation of Pipe complete including conveyance pipe from village to worksite and testing of pipe line etc. complete as per the direction of the Engineer-incharge. |
| 31 | Supplying of 200 mm dia unplasticised rigid UPVC pipe ivory grey in colour having specific gravity of 1.40 to 1.46 gms/ cc of straight length of 6 (six) meter for potable water supplies conforming to IS - 4985/ 2000 of BIS - Ammendment - 2 read with Table - 1 of IS - specification bearing ISI marks for working pressure Cl - IUPVC pipe to withstand pressure of 2.5 kgf/cm² respectively & the specification and manufacturer\"s name should be prominently marked on body of each pipe as per the latest Ammendment of IS - 4985. It includes the cost of sockets in case of plain ended pipe. PDI test are to be conducted and should be marked on body of each pipe and report is to be obtained from CIPET, Bhubanweswar, necessary approval of authority including transportation towork site in complete shape |
| 32 | Supplying of 250 mm dia unplasticised rigid UPVC pipe ivory grey in colour having specific gravity of 1.40 to 1.46 gms/ cc of straight length of 6 (six) meter for potable water supplies conforming to IS - 4985/ 2000 of BIS - Ammendment - 2 read with Table - 1 of IS - specification bearing ISI marks for working pressure Cl - IIUPVC pipe to withstand pressure of 4.0kgf/cm² respectively & the specification and manufacturer\"s name should be prominently marked on body of each pipe as per the latest Ammendment of IS - 4985. It includes the cost of sockets in case of plain ended pipe. PDI test are to be conducted and should be marked on body of each pipe and report is to be obtained from CIPET, Bhubanweswar, necessary approval of authority including transportation towork site in complete shape |
| 33 | Filling the foundation and plinth with excavated material as directed by the Engineer-incharge. A) Hard Soil |
| 34 | Supplying & fitting of RCC ventilators |
| 35 | Monoblock pumpset total head of 24 mtr capable to discharge 1700 LPM with 20 HP/15 KW squirrel cage induction motor fitted with bronze impeller TB-2 of iS 318/1981, companion flanges & class \"F\" insulation suitable for operation 415 volt + 6% - 15%, 3 phasde, 50 Hz aC power supply, suction/delivery = 100x100 mm with BEE star rated energy efficiency pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership network for easy availibility of spares |
| 36 | Control panel with automatic star delta starter sheet steel enclosure vsuitable for operation of squirrel cage induction motor up to 20 HP with 16 Amp.(AC-3) duty contractor at 415 volt+6%-15%, 3 phase, 50 Hz AC supply with over load relay range 8.9 to 13.5 Amp & No volt coil with electronic timer suitable for operation at voltage range of 300 to 440 V. The starter should provide dependable protection against over load and single phasing fitted with Volt meter, Ammeter, MCB in complete shape including indicator lamp |
| 37 | Motor Hood (size 0.45x0.45x0.60 mtr ) made with 18 SWG cold rolled mS sheet with one coat of red oxide primer and two coats of smoke gray / navy blue enamel paint both side (inside & outside) suitable to cover centrifugal monoblock Pump set from 10 to 15 HP and having provision for attachment with the groves on rear side of the panel board |
| 38 | Base frame for panel ( size 0.40x0.20 m )and for Motor ( size 0.50x0.27 m ) made with 3\" size MS channel having suitable holes for fitting of Panel board and different size & make 3 phase centrifugal monoblock pumpset from 10 to 15 HP, coloured with one coat of red oxide primer and two coats of smoke gray enamel paint |
| 39 | 3 x 16 mm² Tarpedore cable XLPE ( cross link polyethylin ) confirming to IS: 7098 (Part-II) including laying below 0.90 mtr of the ground and filling the excavated materials including watering and ramming |
| 40 | 100 mm dia nominal bore GI pipe having wall thickness 4.5 mm electrical resistance welded of medium class confirming to IS - 1239 (pt - 1 of 2004) with socketed at one end and the other end protected with plastic thread protector. The socket confirming to IS - 1239 (pt - II / 1992) with latest amendments in random length of 4 to 7 mtrs. Each pipe should bear ISI certification& manufacturer\"s name/ trademark |
| 41 | 100 mm dia GI Bend IS No. 1239(pt-II/1992) |
| 42 | 100 mm dia GI flange IS No. 6392 / 1971 |
| 43 | 100x100x25 mm GI Tee with plug for priming |
| 44 | 100 mm Ø Sluice Valve Flanged type of Manufacturing Standard - BS 5163 / IS14846 Pressure Ratings PN10. |
| 45 | 100mm C.I. Foot Valve should be of swing type friction less with single disc confirming to iS - 4038/1979 of reputed brand |
| 46 | 100mm C.I. N.R. Valve double flanged swing type PN - 1.0 as per IS:5312 part - I with by-pass arrangement |
| 47 | 250mm C.I. N.R. Valve double flanged swing type PN - 1.0 as per IS:5312 part - I with by-pass arrangement |
| 48 | 200 mm dia Butterfly valve as per IS - specification |
| 49 | 50 mm dia CI AR valve with saddle and riser pipe confirming to IS 14845 with ISI mark |
| 50 | 100 mm dia CI AR valve with saddle and riser pipe confirming to IS 14845 with ISI mark |
| 51 | 200 mm dia PVC Equal tee ( 4 kgf/cm²) confirming to IS - 4995 / 1988 with latest ammendment |
| 52 | 250X250X200 mm dia PVC Equal tee ( 4 kgf/cm²) confirming to IS - 4995 / 1988 with latest ammendment |
| 53 | 250 mm dia PVC Bend ( 135?/90?) ( 4 kgf/cm²) agricultiral PVC fittings confirming to IS - 4995/1988 with latest ammendment |
| 54 | 200 mm dia PVC end cap ( 10 kgf/cm²) confirming to IS - 4995/1988 with latest ammendment |
| 55 | 250 mm dia PVC end cap ( 10 kgf/cm²) confirming to IS - 4995/1988 with latest ammendment |
| 56 | 250x250x110 mm PVC/GI Raiser tee set with bend closing and opening arrangement |
| 57 | 200x200x110 mm PVC/GI Raiser tee set with bend closing and opening arrangement |
| 58 | 250 mm dia PVC coupler ( 4 kgf/cm²) agricultiral PVC fittings confirming to IS - 4995/1988 with latest ammendment |
| 59 | 200 mm dia PVC coupler ( 4 kgf/cm²) agricultiral PVC fittings confirming to IS - 4995/1988 with latest ammendment |
| 60 | 250 mm dis MS pipe (Medium Duty ) 5.4 mm thick with plain ends in random length of 4 to 7 mtr confirming to bIS 3589 with minimum wall thickness of pipes should be 5.5 mm, each pipe should bear ISI specification and manufacturers name / Trade mark, steel grade of the pipe should be Fe330 |
| 61 | Labour charges for cutting, welding and fitting of 250mm dia MS pipe |
| 62 | 250 mm dia MS slippon flange medium duty as per IS specification |
| 63 | 250 mm dia MS Tail piece |
| 64 | Labour charges for cutting, welding & jointing of 250 x100x100 mm M.S. Y Joint |
| 65 | Construction of out let for Tee Tank |
| 66 | Supply of small T & P Kit comprising of hand gloves - 1 pair, tester - 1 no, 8\" cutting plier - 1 no, 12\" sly wrench - 1 no, 12\" screw driver - 1 no, 24/27 & 21/23 DE spanner - 2 nos, 24/27 & 21/23 Ring spanner - 2 nos of Taparia make |
| 67 | Labour charges for installation of 20 HP MB Motorsincluding transportation from village to work site, fitting & fixing of base frame, fitting & fixing suction and delivery pipe to motor, other fitting materials including cutting, welding etc. complete as per the direction of the Engineer-incharge. |
| 68 | Cost of river embankment cutting, cleaning & fitting of suction & delivery fitting with flanges, bend, foot valve, sluice valve, NR valve etc including cost 1/8\" rubber insertion, Nut nolt, white lead paint etc vomplete |
| 69 | Part-B |
| 70 | Construction of 3 phase 11 KV Line as per REC standard confirming to RE Rules 1956 with 300Kg. 9 mtrs.long PSC Pole ( cost excluded ) support in 80Mtrs. Span 55 sqm. AAA Conductor, 11 KV \"V\" cross arm with required nos.of 11KV T &C disc.Insulators and 11KV Pin insulator,carping & padding of poles, danger board at each pole,anticlimbing devices. Stay set at each bending Point and double stay at end point with 18mm G.I. H.T. Stay, concreting of stay with anchor plate,guarding at road crossing etc. including cost of materials,labours, transportation, inspection and commissionng etc. complete. |
| 71 | Cost of LT line with 35 mm² AB Cable 3 phase 4 wire on 8 mtr x 200 kg PSC pole ( 30 mtr span ) including distribution box and pearsing connector ( excluding pole cost ) |
| 72 | Construction and errection of 11/0.4KV , D.P. mounted substation of different capacity confirming to RE Rules 1956 mounted on 2.44mtr. Long structure , supported in 300 Kg 9mtrs. Long PSC Poles, Transformer hard channel and top channel made of 2.8mtrs. long 100X50X6 mm M.S. Channel, Transformer belting on 2.8 mtrs. long 50X50X5 mm M.S. angle (all REC.SPN.Std F-3) with all accessories like3 poles 11 K.V. HG Fuse (F-5) & AB Switches (F-9) both mounted on 2.5 mtrs. long 75X40X6 mm M.S. Channel and supported by 1mtr. long 50X50X5 mm M.S. angle with 3nos. 11 KV lightening Arrestors and distribution box, Pipe earthing(F-2), including cost of 50 sqmm. 3.5 core PVC Cable carping and padding of poles, danger board at each poles, Anti climbing Devices & all other necessary fitting i.e. required size nuts & bolts, brackets Cable sockets etc., construction of barbed wire fencing with double leaf MS Gate with metal spreading, including cost of all materials , labour transportation complete with liasoning for testing inspection & commissioning( excluding cost of PSC pole & Transformer ) 100 KVA Sub-station |
| 73 | Cost of Transformer 100 KVA Transformer (11/0.4 KV ) |
| 74 | Material for 11 KV Line DP WITH ab SWITCH without pole |
| 75 | Plint for 100 KVA Sub-Station |
| 76 | 9 mtr 300 kg PSC pole |
| 77 | 8 mtr 200 kg PSC pole |
| 78 | Barbed wire fencing with metal spreading |
| 79 | Spike provisin |
| 80 | Electrical Earthing |
AI Tender Summary
Tender Timeline
Mar 08, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedMar 16, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 17, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender