Pending / Additional Civil, Repair And Renovation Work Rmrc Murthal Reinvited 1St Time Pending / Additional Civil, Repair And Renovation Work Rmrc Murthal Re-Invited 1St Time
Tender Value
18.29 Lakhs
Estimated cost
Bid Submission
01 Mar 2022
0 days left
EMD
36580
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
sonipat → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Pending / Additional Civil, Repair And Renovation Work Rmrc Murthal Reinvited 1St Time Pending / Additional Civil, Repair And Renovation Work Rmrc Murthal Re-Invited 1St Time
BOQ
| Sl. No. | Item Description |
| 1 | Description and details |
| 2 | HSR ITEM NO. 4.4Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. 4.4.1 All kinds of soil |
| 3 | HSR ITEM NO. 4.12 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge.4.12.1 All kinds of soil |
| 4 | HSR ITEM NO. 5.11Demolishing mud phaska in terracing and disposal of material cum within 50 metres lead. |
| 5 | HSR ITEM NO. 6.1Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level:HSR ITEM NO. 6.1.2 1:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded cum stone aggregate 20 mm nominal size |
| 6 | HSR ITEM NO. 6.1.61 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size) |
| 7 | HSR ITEM NO. 6.1.8 1:5:10 (1 cement : 5 fine sand : 10 graded stone cum aggregate 40 mm nominal size) |
| 8 | HSR ITEM NO. 6.16 Reinforced cement concrete work in beams, suspended floors, cum roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). |
| 9 | HSR ITEM NO. 6.14.1 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level:6.14.1 1:1.5: 3 ( 1 cement : 1. 5 coarse sand (zone-Ill): 3 cumgraded stone aggregate 20 mm nominal size) |
| 10 | HSR ITEM NO. 6.13 Making plinth protection 50mm thick of cement concrete 1 :3:6 (1 sqm cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth |
| 11 | HSR ITEM NO.6.30 Centering and shuttering including strutting, propping etc. andremoval of form HSR ITEM NO.6.30.3Suspended floors, roofs, landings, balconies |
| 12 | HSR ITEM NO.6.30.4 Shelves (Cast in situ) |
| 13 | HSR ITEM NO. 6.34Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level.Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, over1aps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. 6.34.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 14 | HSR ITEM NO. 7.21.2Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: |
| 15 | HSR ITEM NO. 7.22.2 Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in |
| 16 | HSR ITEM NO. 9.17Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design :9.17.1 In 75x75 mm deep chase |
| 17 | HSR ITEM NO. 9.18 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete |
| 18 | HSR ITEM NO. 9.57 Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed 9.57.3150 mm diameter |
| 19 | HSR ITEM NO. 9.14 Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1 :3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1 :3 (1 cement : 3 fine sand) and finished neat: 9.14.1 With common burnt clay non-modular brick tiles of class designation 1 O |
| 20 | HSR ITEM NO. 9.14 Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1 :3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1 :3 (1 cement : 3 fine sand) and finished neat: 9.14.1 With common burnt clay non-modular brick tiles of class designation 1 O(Labour Rate) |
| 21 | HSR ITEM NO. 10.58 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS :(thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 22 | HSR ITEM NO. 10.59 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1 :4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 23 | HSR ITEM NO.11.5.4 12 mm cement plaster of mix : 11.5.21 :3 (1 cement: 3 fine sand) |
| 24 | HSR ITEM NO. 11.6.2 15 mm cement plaster on the rough side of single or half brick wall of mix .11.6.11 :4 (1 cement: 4 fine sand) |
| 25 | HSR ITEM NO. 11.25 Pointing on brick work or brick flooring with cement mortar 1 :3 (1 cement : 3 fine sand): 11.25.1 Flush / Ruled/ Struck or weathered pointing |
| 26 | HSR ITEM NO.11.83 Painting over the wooden surface with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade 11.83.1 Two or more coats on new work over an under coat of suitableshade with ordinary paint of approved brand and manufacture |
| 27 | HSR ITEM NO. 11.93 Finishing walls with water proofing cement paint of required shade :11.93.1 New work (Two or more coats applied@ 3.84 kg/10 sqm) |
| 28 | HSR ITEM NO. 11.64 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade:11.64.1 New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 29 | HSR ITEM NO. 12.9.7 Float glass panes12.9.7.1 4 mm thick glass pane (weight not less than 10kg/sqm). |
| 30 | HSR ITEM NO.12.157 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 12.157.1 For fixed portion 12.157.1.2 Powder coated aluminium (minimum thickness of kgpowder coating 50 micron) |
| 31 | HSR ITEM NO.12.157.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 32 | HSR ITEM NO.12.159 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 12.159.1 With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 33 | HSR ITEM NO. 13.29 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required: 13.29.2 In grating, frames, guard bar, ladder, railing, brackets, gates and similar works |
| 34 | HSR ITEM NO. 17.69.2 Providing and Laying 80 mm thick ISi marked lntertocking Paver Blocks conforming to IS 15658:2006/IRC SP 63: 2004 of all shapes and colours in design mix cement M 40 over the bed of 30 mm thick fine sand complete in all respect. |
| 35 | HSR ITEM NO. 17.69.2 Providing and Laying 80 mm thick ISi marked lntertocking Paver Blocks conforming to IS 15658:2006/IRC SP 63: 2004 of all shapes and colours in design mix cement M 40 over the bed of 30 mm thick fine sand complete in all respect. (Labour Rate) |
| 36 | HSR ITEM NO. 21.95 Providing lowering cutting jointing and testing RCC pipe class NP 3 as per 18-458-2003 with spigot & socketed joints manufactured with ISi marked sulphate resistance cement as per ISi 12330 with rubber rings ISi marked antiternmite as required at site in to trenches for all depths and laying out the same to correct alignment gradients and levels including dressing and trimming and cutting of concrete beds and side of trenches, if required jointing with rubber rings in trenches and jointing with 1 :3/2 cement sand mortar and with end dowels filled with 1 :3/2. cement sand mortar and finishing the joints at an angle of 45 degree with faces of spigot of socket joints cutting and finishing the cut surface to a uniform finish etc. as fully described in item No . 21.38, item 21.44, item 21.45, & item 21.46 including cartage loading and unloading complete in all respects. the internal diametric of the sewer being:(Labour Rate) 21.95.7 800mm |
| 37 | HSR ITEM NO. 30.20 Flush pointing with cement mortar 1 :3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for prefixed flat tile bricks on top of mud phaska: HSR ITEM NO.30.20.1 With F.P.S. brick tiles With F.P.S. brick tiles |
| 38 | NS Items:- Supply and filling of Local Earth at site brought from outside the campus with irrespective of lead, including loading & unloading, carriage,royalty/compensation etc. The earth will be laid in 25 cm layers & will be compacted with 8-10 Ton Road Roller i/c ramming, watering and consolidation complete in all respects to the entire satisfaction of the Engineer-in-charge. (NS) |
| 39 | Providing of JCB including the cost of Driver, fuel etc. for leveling of land, removal of grass and trees. (NS) |
| 40 | SUPPLY INSTALLATION TESTING & COMMISSIONING OF SLIDING GATE MOTOR MAKE NICE ITALY, MODEL ROBUS 1000 KIT. IRREVERSIBLE, 24V VDc, WITH BUILT IN CONTROL CIRCUIT WITH ELECTROMECHANICAL LIMIT SWITCH FOR SLIDING GATES WEIGHING UP TO 1000 KG AND PUSH BUTTON. INCLUDING PHOTOCELL (1 Pair), RACK SAW TEETHED WITH STURD (as per site requirement), MS WHEEL WITH DOUBLE BEARING (2 Nos.), NYLON ROLLER WITH DOUBLE BEARING (6 Nos.) COMPLETE IN ALL RESPECT AS PER THE SATISFACTION OF ENGINEER INCHARGE. (NS) |
AI Tender Summary
Tender Timeline
Feb 09, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedMar 01, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 02, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender