Construction Of Room-Cum-Shed And Toe Wall Of Retractable Poly House And Shade Net House At Regional Research Centre, Raiya Jhajjar Re-Invited 2Nd Time
Tender Value
12.72 Lakhs
Estimated cost
Bid Submission
01 Mar 2022
0 days left
EMD
25440
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
jhajjar → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Room-Cum-Shed And Toe Wall Of Retractable Poly House And Shade Net House At Regional Research Centre, Raiya Jhajjar Re-Invited 2Nd Time
BOQ
| Sl. No. | Item Description |
| 1 | Description and details |
| 2 | HSR ITEM NO. 4.12 Earth work in excavation by mechanical means(Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge.4.12.1 All kinds of soil |
| 3 | HSR ITEM NO. 4.32Filling available excavated earth (excluding rock) in trenches, cum plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 4 | HSR ITEM NO. 6.1.71:5:10 (1 cement : 5 coarse sand (zone-Ill): 10 graded stone aggregate 40 mm nominal size) |
| 5 | HSR ITEM NO. 6.8 Providing and laying damp-proof course with cement concrete 1 :2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size)6.8.2 40mm thick |
| 6 | HSR ITEM NO. 6.13Making plinth protection 50mm thick of cement concrete 1 :3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth |
| 7 | HSR ITEM NO. 6.14 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level.6.14.1 1:1.5:3 ( 1 cement : 1. 5 coarse sand (zone-Ill): 3 cum graded stone aggregate 20 mm nominal size) |
| 8 | HSR ITEM NO. 6.15Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement :6.15.1 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 cum graded stone aggregate 20 mm nominal size) |
| 9 | HSR ITEM NO. 6.16Reinforced cement concrete work in beams, suspended floors,roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). |
| 10 | HSR ITEM NO. 6.29Centering and shuttering including strutting, propping etc. and removal of form work for :6.29.1 Foundations, footings, bases for columns |
| 11 | 6.29.3 Columns, piers, abutments, pillars, posts and struts |
| 12 | HSR ITEM NO. 6.30 Centering and shuttering including strutting, propping etc. and removal of form for : 6.30.3 Suspended floors, roofs, landings, balconies |
| 13 | 6.30.5Lintels, beams, plinth beams, girders, bressumers sqm and cantilever |
| 14 | HSR ITEM NO. 6.34Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level.Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, over1aps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to beincluded in the rates for reinforcement. 6.34.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 15 | HSR ITEM NO. 7.21Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in:7.21.2 Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 16 | HSR ITEM NO. 7.22 Brick work with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes. 7.22.2 Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 17 | HSR ITEM NO. 7.28 Half brick masonry with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level. 7 .28.2 Cement mortar 1 :4 ( 1 cement :4 coarse sand) |
| 18 | HSR ITEM NO. 9.14Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1 :3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1 :3 (1 cement : 3 fine sand) and finished neat:9.14.1 With common burnt clay non-modular brick tiles of classdesignation 10 |
| 19 | HSR ITEM NO. 9.18 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete |
| 20 | HSR ITEM NO. 9.17Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design :9.17.1 In 75x75 mm deep chase |
| 21 | HSR ITEM NO. 9.57 Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.9.57.2110 mm diametre |
| 22 | HSR ITEM NO. 10.1 Providing and laying of base course of floors consisting of 100 mm thick sqm cement 1 :8: 16 and 100 mm sand or stone filling. |
| 23 | HSR ITEM NO. 10.7 Providing and laying of conglomerate floor 50mm thick cement concrete topping 1 :2:4 |
| 24 | HSR ITEM NO. 10.58 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 25 | HSR ITEM NO.10.63 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.10.63.2 Size of Tile 600x600 mm |
| 26 | HSR ITEM NO. 10.67 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. 10.67.2 Size of Tile 600x600 mm |
| 27 | HSR ITEM NO. 11.5 12 mm cement plaster of mix :11.5.41 :6 (1 cement: 6 fine sand) |
| 28 | HSR ITEM NO. 11.615 mm cement plaster on the rough side of single or half brick wall of mix : 11.6.2 1 :6 (1 cement: 6 fine sand) |
| 29 | HSR ITEM NO. 11.58Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete |
| 30 | HSR ITEM NO. 11.71Wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade :11. 71.1 Two or more coats on new work |
| 31 | HSR ITEM NO. 11.93.1 Finishing walls with water proofing cement paint of required shade :11.93.1 New work (Two or more coats applied@ 3.84 kg/10 sqm) |
| 32 | HSR ITEM NO. 11.95Finishing walls with Acrylic Smooth exterior paint of required shade : 11.95.1 New work (Two or more coat applied @ 1.67 litre/1 O sqm overand including priming coat of exterior primer applied @ 2.20 kg/10 sqm |
| 33 | HSR ITEM NO. 12.157 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 12.157.1 For fixed portion 12.157.1.2Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 34 | HSR ITEM NO. 12.157.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 12.157.2.2Powder coated aluminium (minimum thickness of kgpowder coating 50 micron) |
| 35 | HSR ITEM NO.12.158 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge 12.158.2 Pre-laminated particle board with decorative lamination on both sides |
| 36 | HSR ITEM NO. 12.159 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): 12.159.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm |
| 37 | HSR ITEM NO. 22.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 22.1.4 White vitreous chinaware Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 38 | HSR ITEM NO. 22.5 Providing and fixing white vitreous chinaware pedestal for wash basincompletely recessed at the back for the reception of pipes and fittings |
| 39 | HSR ITEM NO. 22.23 Providing and fixing white vitreous chinaware pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. 22.23.1 W.C. pan with ISi marked white solid plastic seat and lid |
| 40 | HSR ITEM NO. 22.26 Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :22.26.2 Single half stall urinal with manually operated5 litre P.V.C.flushing cistern and manually operated stop cock/ angle valve |
| 41 | HSR ITEM NO. 22.38 Providing and fixing 8 mm dia C.P. I S.S. Jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge |
| 42 | HSR ITEM NO. 22.86 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 22.86.2 20 mm nominal outer dia Pipes |
| 43 | 22.86.3 25 mm nominal outer dia Pipes |
| 44 | HSR ITEM NO. 22.104 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 22.104.1 15 mm nominal bore |
| 45 | HSR ITEM NO. 22.106 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 22.106.1 15 mm nominal bore |
| 46 | HSR ITEM NO. 22.107 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 22.107.1 15 mm nominal bore |
| 47 | HSR ITEM NO.22.127 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms |
| 48 | HSR ITEM NO. 20.71 Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge.20.71.1 48\" (1200mm) |
| 49 | HSR ITEM NO. 23.3 COPPER WIRING IN PVC CONDUIT (SURFACE/RECESS)23.3.1 Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. 23.3.1.1 Group A |
| 50 | 23.3.1.2 Group B |
| 51 | 23.3.1.3 Group C |
| 52 | HSR ITEM NO. 23.3.4 Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin socket and 1 no 5/6 Amp switch required MS Box etc complete as required.23.3.4.1 Group A |
| 53 | 23.3.4.3 Group C |
| 54 | HSR ITEM NO. 23.3.5 Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin socket and 1 no 15/16 Amp switch required MS Box etc complete as required.23.3.5.3 Group C |
| 55 | HSR ITEM NO. 23.3.6 Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 23.3.6.7 2 run of Size 2.50 Sqmm(1.1.80mm) |
| 56 | 23.3.6.8 2 run of Size 4 Sqmm(1/2.24mm) |
| 57 | HSR ITEM NO. 23.7 PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL23.7.6 Supply and erection of PVC CONDUIT ISi marked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, ironhooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work.23.7.6.1 PVC pipe of 20 mm dia. |
| 58 | 23.7.6.2 PVC pipe of 25 mm dia. |
| 59 | 23.7.6.4 PVC pipe of 40 mm dia |
| 60 | HSR ITEM NO.23.8.10 Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cmlong M.S. Road made into suitable suspension hook and erected in R.C.C. slab for the erection of fan complete with all labour and material required to complete the job. |
| 61 | HSR ITEM NO. 23.8.10 Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects.23.8.10.2 3 Modules |
| 62 | 23.8.10.3 4 Modules |
| 63 | 23.8.10.4 6 Modules |
| 64 | HSR ITEM NO. 23.8.11Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect.23.8.11.1 5 amp 1 way switch |
| 65 | 23.8.11.3 15 amp 1 way switch |
| 66 | 23.8.11 4 5 amp Socket |
| 67 | 23.8.11.515 amp 6 pin Socket |
| 68 | 23.8.11.7 step type Fan Regulator 2 modules 300 watt |
| 69 | HSR ITEM NO. 23.9 Erection of exhaust fan in existing opening ,complete with necessary earthling of fan including carriage from PWD store to the site of work. |
| 70 | HSR ITEM NO. 23.11 Making suitable hole in the wall suitable for exhaust fan up to 450 mm sweep including finishing the same and fixing of Stainless steel wire mesh 2 mm thick having about 50 meshes per inch at exhaust side complete as required |
| 71 | HSRB ITEM NO. 23.22 MCCB ,DISTRIBUTION BOARDS, MCB\"s, RCCB\"s, CHANGE OVER etc. 23.22.4 Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work.23.22.4.5 TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing) |
| 72 | HSR ITEM NO. 23.22.5 Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:-23.22.5.1 6 amp. to 32 amp Single Pole |
| 73 | 23.22.5.7 6 amp. to 32 amp MCB\"s FOUR POLE |
| 74 | HSR ITEM NO. 24.1 EARTHING AND LIGHTENING ARRESTOR 24.1.1 Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. |
| 75 | 24.1.11 Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required. |
| 76 | NS S/E Surface wall mounted 20 watt integrated LED 4 feet fitting completed in all respect. Make Philips, Havells,Wipro,Bajaj etc. |
| 77 | NS S/E of LED surface type Down lighter 15 watt/18 watt |
AI Tender Summary
Tender Timeline
Feb 09, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedMar 01, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 02, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender