Bids Are Invited For 1 CONSTR 1 ISMB 150 RSJ 150 x 75mm 3.75mtr long conforming to relevant IS make TATA Sail Jindal 2 CONSTR 2 ISMB 150 RSJ 150 x 75mm 3.90 mtr long conforming to relevant IS make TATA Sail Jindal 3 CONSTR 3 ISMB 150 RSJ 150 x 75mm 0., Kupwara-Jammu And Kashmir

Bids Are Invited For 1 CONSTR 1 ISMB 150 RSJ 150 x 75mm 3.75mtr long conforming to relevant IS make TATA Sail Jindal 2 CONSTR 2 ISMB 150 RSJ 150 x 75mm 3.90 mtr long conforming to relevant IS make TATA Sail Jindal 3 CONSTR 3 ISMB 150 RSJ 150 x 75mm 0.90 mtr long conforming to relevant IS make TATA Sail Jinda 4 CONSTR 4 ISMB 150 x 75 mm 3.96 mtr long conforming to relevant IS 5 CONSTR 5 Steel beam ISMB 125mm RSJ 125 X 70mm 2840 mm long conforming to IS 808 1973 6 CONSTR 6 ISMB 150 RSJ 150 x 75mm 4.90mtr long conforming to relevant IS 7 CONSTR 7 ISMB 150 RSJ 150x75mm 5.80 mtr long 15 kg per RM conforming to relevant IS 8 CONSTR 8 ISMB 150 x75mm 3 mtr long conforming to IS 808 7973 9 CONSTR 9 Steel roofing trough SRT of size 2000 mm x 613 mm x 180 mm made out of 2 mm thick hot rolled carbon steel sheet conforming to relevant IS complete with set of a spanner OJDE of size 20 to 22 per 10 Nos of SRT SRTs shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer. 10 CONSTR 10 Steel roofing trough SRT of size 1630 mm x 613 mm x 180 mm made out of 2 mm thick hot rolled carbon steel sheet conforming to relevant IS complete with set of a spanner OJDE of size 20-22 per 10 Nos of SRT SRTs shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer 11 CONSTR 11 HDPE sand bag of size 75x40 cm Sand colour and each bag having weight not less than 60 gms 12 CONSTR 12 LDPE sheet 5.49 Mtr wide weighing 1.00 Kg per RM black in color and shall contain not less than 2.0 percent of carbon black of and avereage particle size 0.01 to 0.02 micron well dispersed in mass 13 CONSTR 13 LDPE sheet for PCC construction150 micron thick best quality 14 CONSTR 14 LDPE sheet having weight 0.26 kg Sqm BLACK Conforming to relevant IS of width 5.5 Mtr 15 CONSTR 15 Low density polyethylene sheet 5.49 m wide weighing 1.00 Kg mtr black in colour and shall contain not less than 2.0 percent of carbon black of average particle size 0.01 to 0.02 micron well dispersed in mass sample to be approved before supply 16 CONSTR 16 MS hexagonal nuts bolts and washers 12 mm dia 40 mm long 17 CONSTR 17 Pre fabricated steel ventilator loop hole of size 1.20m x 0.30m shall be provided the main frame work shall be MS channel U section 12mm grove x 6mm thick MS sheet 2 mm thick of size 0.60 x 0.30m 02 nos for shutter will be fixed in MS U channel for smoothly sliding two nos bow handles are also provided for easy opening and sliding the shutters and for external side acrylic sheet bottom hung shutters including all required iron mongery will be provided ventilators shall be shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer all materials shall conform to relevant IS make TATA or SAIL or Jindal sample to be app roved before supply 18 CONSTR 18 Pre fabricated steel door of size 0.90m x 1.80m made out of 2mm thick MS black carbon sheet welded to 30x30x6mm ISA door shutter frame fitted to 50x50x6mm ISA door frame including 06 Nos hold fast 03 Nos 125mm long MS butt hinges 02 nos MS tower bolt 200mm long 02 nos MS bow handle 125mm long one nos MS sliding bolt 250mm long and door shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer all materials shall conform to relevant IS 19 CONSTR 19 Pre-fabricated steel loop holes of size 0.60M x 0.40M made out of MS flat iron of size 20 x 4mm and MS round bar 16mm dia with 6mm thick MS plate shutter including 03 nos MS pintle hinges made of FI 35 x 4 mm thick and MS tower bolt complete as per drawing loop holes shall be painted with two coats OG colour of synthetic enamel paint over a coat of red oxide primer 20 CONSTR 20 Pre-fabricated storage rack made out of angle iron 50mm x 50mm x 4mm thick 6 nos of length 0.65 mtr angle iron 50mm x 50 mm x 4 mm thick 2 nos of length 1.80 mtr angle iron 50mm x 50 mm x 4 mm thick 6 Nos of length 0.45 mtr and MS sheet 2mm thick of size 1m x0.45m 02 Nos make as per the mild steel racks will be provided with two coats of green paint over one coat of red oxide sample to be approved before supply 21 CONSTR 21 Prefabricated steel door of size 1.50 x1.80Mtr made out of 2 mm thick MS Plate two nos of shutters welded or riveted on 50x50x6mm ISA shutter frame frame fitted fitted on door column 2.1 Mtr long made up of equal angle 65 x 65 x 6 mm with 03 nos hinges and 03 nos holdfasts incl all requisite iron mongery door shall be painted with two coat of OG synthetic enamel paint over onecoat of red oxide primer 22 CONSTR 22 MS TMT bars 10 mm dia conforming to relevant IS make Kamdhenu or Tata or Sail 23 CONSTR 23 MS TMTbars 8 mm dia conforming to relevant IS make Kamdhenu or Tata or Sail 24 CONSTR 24 MS TMT bars 16mm dia conforming to relevant IS make TATA or SAIL or RINL 25 CONSTR 25 MS TMT bars 12mm dia conforming to IS 1786 1985 make TATA SAIL RINL 26 CONSTR 26 MS TMT bars 8mm dia conforming to relevant IS make TATA or SAIL or RINL 27 CONSTR 27 MS TMT bars 10 mm dia conforming to relevant IS 28 CONSTR 28 Mild steel TMT bars 25mm dia 29 CONSTR 29 MS binding wire 0.9 mm dia annealed conforming to relevant IS 30 CONSTR 30 CGI Sheet of size 8 feet x 3 feet x 0.63mm thick conforming to relevant IS make TATA SAIL RINL 31 CONSTR 31 CGI Sheet of size 2500 x 885 x 0.63mm thick conforming to IS 277 1985 make TATA SAIL RINL 32 CONSTR 32 CGI sheet 810 x 2440mm long, 0.63mm thick with galvanized of 375 GSM galvanisation as per IS 429 33 CONSTR 33 Paint Synthetic Enamel 1st quality OG Make Asian Apcolite/ Berger Luxol or Shalimar Superlac or Nerolac 34 CONSTR 34 Synthetic enamel paint colour olive green in 20 Ltr container Ist quality conforming to relevant IS of make nerolac berger or Asian paint 35 CONSTR 35 Red oxide primer conforming to relevant IS 36 CONSTR 36 PBS roll self finished tarfelt grade I conforming to relevant IS of size 1.00 mtr width and 20.00 Mtr long wt not less than 42.50 2.50 Kgs sample to be approved before supply 37 CONSTR 37 Thinner sample to be approved before supply 38 CONSTR 38 Dry distemper sample to be approved before supply 39 CONSTR 39 Dry distemper sample to be approved before supply 40 CONSTR 40 Paint Brush 4 inch make Amar or Lucky sample to be approved before supply 41 CONSTR 41 Paint brush 3 inch make Amar or Lucky sample to be approved before supply 42 CONSTR 42 Nails all type 43 CONSTR 43 Ply wood 2.00m x 0.30m and 12mm thick 44 CONSTR 44 Ply wood 2.00m x 0.60m and 12mm thick 45 CONSTR 45 Water proof Ply wood 8 feet x 4 feet x 12mm make National 46 CONSTR 46 Water Proofing Compound conforming to relevant IS make JK or Birla 47 CONSTR 47 ISA 65x65x6 mm 2mtr long conforming to relevant IS 48 CONSTR 48 CI Grating of size 300x 300mm with frame weight not less than 4 kg sample to be approved before supply 49 CONSTR 49 Chalk whiting Sample to be approved before supply 50 CONSTR 50 MS plate form work of columns footing of 1.2 x 1.2 x 0.6 m made of 1.20mm thick MS sheet using MS angle iron 40 x 40 x4 mm to all four sides and with one No cross bracing set on all sides with holes pre drilled for fixing with 12mm dia nuts and bolts MS plate and angles shall ne applied two coats of red oxide primer 51 CONSTR 51 MS plate form work of columns footing of 0.45 x 0.45 x 0.9 m made of 1.20mm thick MS sheet using MS angle iron 40 x 40 x4 mm to all four sides and with one no cross bracing set on all sides with holes pre drilled for fixing with 12mm dia nuts and bolts MS plate and angles shall ne applied two coats of red oxide primer 52 CONSTR 52 Glass dividing strip 48mm x 3mm thick for flooring Sample to be approved before supply 53 CONSTR 53 Two tier sleeping bunks MS pipe two tier sleeping bunks as per CE 15 Corps Drawing No 3534/ OW/15 Corps / Two tier sleeping bunk per sheet 1 per 1 dated 10 Apr 218 attached with this TS a detachable ladder made up with 20 mm MS pipe with four steps to be provided in each bunk male and female MS rectangular box of size 50 mm x 25 mm x 75 mm long to be welded two side protector bars of 15 mm dia MS pipe on top bunk to be welded as per details shown in drawing the outer size of the bunk will be 1970 mm x 950 mm horizontally and 1950 mm x 950 mm vertically the bunk should have provision to place a removable type matress of size 1830 mm x 910 mm to angle iron frame with adequate holes pre drilled in the frame all MS pipes shall be medium grade ISI mark and provided with two coats of superior quality black spray paint over a coat of red oxide primer two nos single piece cushion made of 100 mm thick PUF foam of density 40 Kg per cum as applicable for sleeping cushions to be provided with each bunk removable type of standard make sleepwell per kurlon of size 1830 mm x 910 mm the puf foam pasted on the plywood shall be enclosed vinyl coated laminated upholtery cloth Rexene of specification as mentioned 54 CONSTR 54 Precast cement concrete lintel in window and door of length 1.80 m, width 450 mm and 200 mm thick Type B 1 to 1 to 2 to 4 and 20 mm graded aggregate set in cement mortar 1 to 4 including necessary form work and the reinforcement with TMT bars should be of Main bars with 12 mm dia bars, 04 Nos and Stirrups with 8 mm dia bars,13 Nos including fabrication with binding wire etc 55 CONSTR 55 Precast cement concrete lintel in Door of length 1.20 m width 450 mm and 200 mm thick Type B 1 1 to 2 to 4 20 mm graded aggregate set in cement mortar 1 to 4 including necessary form work and the reinforcement with TMT bars should be of Main bars with 12 mm dia bars 04 Nos and Stirrups with 8 mm dia bars,09 Nos including fabrication with binding wire etc 56 CONSTR 56 Steel window 1500x600mm shall be provided. The main frame work shall be MS channel U sec 25x25x5mm 12mm grove x 6mm thick shulters of size 0.06x0.30m and 6mm thick will be fixed for smoothly sliding within MS U channel Two bow handles are also provided for easy opening and shifting the shulters Externally Acrylic sheet bottom hung shutters will be provided incl iron mongery etc completed incl painting 57 CONSTR 57 Steel window 1200x600mm shall be provided. The main frame work shall be MS channel U sec 25x25x5mm 12mm grove x 6mm thick shulters of size 0.06x0.30m and 6mm thick will be fixed for smoothly sliding within MS U channel Two bow handles are also provided for easy opening and shifting the shulters Externally Acrylic sheet bottom hung shutters will be provided incl iron mongery etc completed incl painting 58 CONSTR 58 GI Wire mesh crate box type size of mesh box 2000 x1000x1000mm and size of mesh 100 x 100mm and dia of GI wire 3.40mm for outer support and 2.70mm for mesh with tolerance of 5 percent and confirming to relavant IS Make TATA/SAIL/Jindal sample to be approved before supply 59 CONSTR 59 Galvanised J hooks with bitumen cup washer including nuts 8 mm dia 150 mm long conforming to relevant IS sample to be approved before supply 60 CONSTR 60 Scantling timber 3 inch x 2 inch and 5 feet long 2nd class hard wood sample to be approved before supply 61 CONSTR 61 Wooden ballies of size 10 feet long and 6 inch dia at bottom Sample to be approved before supply 62 CONSTR 62 03 Nos MS rack of size 1.22m x 0.61m x 1.65m.Vertical legs and frame of the racks shall be fabricated out of MS slotted angle iron 65 x 35 x 3mm thick with 2 middle supports of FI 40x 6mm 1.88Kg/RM in horizontal frame of racks The rack will have 2 shelves with 12mm thick ply wood Make Kitply/ Green Ply The plywood will be fixed with frame with the use of nuts and bolts of 12mm dia The horizontal frame and vertical legs of the racks will be jointed with 12mm dia nut and bolt and angle iron cleats as required all as per drawings attached 63 CONSTR 63 Fire extingusher Fire extingusher 06 Kgs capacity ABC powder MAP 90 alongwith its accessories confirming to relevant IS 64 CONSTR 64 PVC SWR pipe 110 mm dia single socketed 3 mtr long Make Supreme Polycab Finolex Anchor 65 CONSTR 65 Steel loop hole 610 mm x 330 mm fabricated with U channel frame work of size 25x25mm and 5mm thick and necessary FI to be fixed for sliding arregement with 6mm thick MS plate sliding shutter with necessary iron mongries including applying two coats of synthitic enamel paint over one coat of red oxide primer internally and acrelic sheet shutter externally bottom hined 66 CONSTR 66 Steel door confirming to IS 1038 1938 of size1800mm x 650mm, 3 Nos 125mm butt hinges 2 Nos MS tower bolt 200mm long 2 Nos MS bow handle 125mm long two No MS sliding bolt 250mm long all fittings fabricated with steel door and angle iron 40 x 40 x 6mm chowkat frame and shutter frame 35 x 35 x 5 mm including two coat of synthetic enemal paint over one coat of red oxide primer complete all are shown on drg All materials shall conforming to relevant IS 67 CONSTR 67 Steel lintel for door and Loop holes made out of ISA 35x35x5mm 910 mm long complete all as per brief specification and drawing 68 CONSTR 68 Prefab steel Jally made up of ISA 30x30x3mm frame and 25x25x3mm 90mm center to center both ways welded to frame of size 900x900mm complete all as per specification 69 CONSTR 69 Mild steel angle double shelf made out of MS Angle 35x35x5mm hold fast 130mm long and MS Sheet welded with the MS angle 1.6mm complete all as per specification and drawing 70 CONSTR 70 Bitumen 80 per 20 grade Make SHALIMAR or equivelent make 71 CONSTR 71 APP membrane for water proofin conforming to IS 1322 198 of size 20m x 0.90m weight of each roll shall not be less than 42.50 Kgs 2.5 Kgs in dry conditions the finished mtrl shall be free from visible external defect such as holes oil patches ragged or untrue edges brakes cracks tears protuberances and indentations 72 CONSTR 72 Oil bound distemper of IVORY shade make Asian/Berger/Shalimar 73 CONSTR 73 110mm dia UPVC SWR pipe single socketed pipe Type A in any length with rubber joint 74 CONSTR 74 Heating device kerosene based heating device of following specifications will be provided with each shelter Make Paseco PSG-22G per Kero Heat CV-2230 Toyotomi (i) Type of Heater Convection(ii) Heat Output Max. 23000 BTU per hr(iii) Fuel Tank Integral(iv) Tank Capacity 1.9.U.S.gallons 7.1915 Ltrs(v) Continuous Combustion Time Approx. 8 12 hr(vi) Max.Fuel Consumption 0.167 U.S. gallons/hr 0.6321 Ltrs/hr (vii) Ignition Method Battery C Cell x 2 Igniter Type B (viii) Weight (empty) Approx 23 Ibs 10.4328 Kgs (ix) Dimensions.(a) Height 26.8 inches (b) Width 17.5 inches(c) Depth 17.5 inches(x) Wick Height 25/64 IN 10mm 75 CONSTR 75 Freshly burnt fat lime class C white in clour conforming to relevant IS 76 CONSTR 76 Wooden ballies 10 feet long and not less than 4 inch dia Sample to be approved before supply 77 CONSTR 77 Wooden scantling 50 x 75mm size 2100 mm long of 2nd class hard wood 78 CONSTR 78 Wooden planks 2nd class hard wood 20mm thick 300mm wide 1800 mm long 79 CONSTR 79 Provn of solar lanterm provn of solar lantern comprising of 3 LED bulbs of power consumption 3 Watts each bulb each bulb combination of 3 or 4 LEDs with Built in chargeable battery 12 Volts 7.20 AH SMF lead acid battery and solar panel 12 V 10W polycrystalline with charging cable complete including all required accessories make ANDSLITE or TATA BP or equivalent 80 CONSTR 80 PVC sheets 1.5 mm thick laminated plain coloured marbled mosaic or mottled finish laid with approved rubber based adhesive in floors sample to be approved before supply 81 CONSTR 81 Approved adhesive for setting of rubber tiles/linoleum sheets 82 CONSTR 82 Wooden wall panelling of size 4 6 mm thick and scantling of size 11 by 2 inch x 2 inch for frame work including supply of sufficient qty of nails 83 CONSTR 83 Wood varnish ISI marked 84 CONSTR 84 Steel door of size 1.8M x 1.85 M confirming to IS 1038 1983 shall be provided for entrance as per drg sheet No 6/8 The main frame shall be of angle iron 50 x50x6mm and shutters frame work shall be of MS angle 40 x40x6mm MS sheet 2mm shall be provided as cladding of shutters door shutters shall be tied with pintel hinges in such a way so that it can open on both sides and fixed on either side of entranc diagonal bracing of MS flat iron 30 x 5mm and intermediate support of MS tee 40 x40 x6mm as shown in drg sheet No 6/8 shall be provided to shutter Door shall be provided with iron mongories as shown on drg and shall be painted with twocoats of synthetic enamel paint over a coat of red oxide primer 85 CONSTR 85 Quarry stone for random rubble masonry of grading between 150mm to 250mm Note stone may be of any shape but shall be not less than 15 cm in any direction sample to be approved before supply 86 CONSTR 86 Loop holes will be of size 2.00m x 0.90 m as shown in the drg loop holes will be made of angle iron frame of size 50 x 50 x6mm shall be used for mainframe MS sheet 6mm thick shall be used as bottom hung shutters 3 shutters of size 0.66 x 0.90 mtr shall be used with 2 nos MS pintel hinges loop holes will be provided with two hold fasts on each side and four holdfasts on bottom five bolts shall be welded at top of loophole to fix window in lintel band each shutter shall be provided with two nos fabricated tower bolts and two MS handle of 100mm made out of flat iron 25 x 4mm 02 Nos of flat iron 40 x5mm shall be welded to one shutter in each loop hole to close gap between shutters five nos MS flat iron 50 x6mm with predrilled holes at free end of 45 cm length shall be welded on top loop hole shall be painted with twio coats of synthetic enamel paint over a coat of red oxide primer 87 CONSTR 87 Anti Missile screen anti missile screen of size 2.00 x 0.90m made of frame of MS angle iron 50 x50x 6mm frame to be provided with two hold fasts on each side and four hold fasts on bottom of 300mm length MS flat iron 40 x 6 mm five bolts shall be welded at top of frame to fix windows in lintel band each nut to be welded with 2 nos 75mm long 12mm dia round bars made to shape as shown in drawing shuters frame of 1.98 x 0.88 mtr with ISA 40 x40x 6mm used as bottom hung shutters with 03 x MS pintel hinges each shutters shall be provided with two nos fabricated tower bolts wire fabric of 3.50 mm dia wire with 50 x50mm mesh size shall be fitted to angle iron shutter with help of MS flat iron 40 x5mm and nut and bolts of size 12mm dia x 40mm long at C/C distance not more than 30cm each shutters shall be provided with 02 x 12mm dia PP nylon rope of 3 mtr length for operation of shutters each shutter shall be provided with02 x MS stands provided at top of shutter so that shutters can rest on wall having 45 degree angle with ground anti missile screen shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer 88 CONSTR 88 Bricks sub class B old size conforming to IS 1077 1986 89 CONSTR 89 Primer for water proofing treatment conforming to IS 3386 1986 90 CONSTR 90 Bitumen 85 25 conforming to IS 702 1988 91 CONSTR 91 3mm thick polymeric water proofing membrane not less than 3 kg per sqmtr with HDPE core of 200micron thickness make IWL or equivalent 92 CONSTR 92 Second class hard wood planks 20 mm thick 300 mm wide and 1800 mm long sample to be approved before supply 93 CONSTR 93 PCC hollow blocks 400 mm x 200 mm x 200 mm using cement concrete type 1 to 3 to 6 16mm graded aggregate Hollow blocks shall be sound free from cracks broken edges honey combing and other defects that would interfere with the proper placing of blocks or impair the strength or performance of construction 94 CONSTR 94 Rapidite quick setting liquid 95 CONSTR 95 Integrated water proofing compound 96 CONSTR 96 PCC Solid blocks 400 mm x 200 mm x 200 mm minimum strength 50kg/sqcm PCC shall conform to relevant IS solid block made out PCC 1:3:6 having the compressive strength 5 KN/Sqmm 97 CONSTR 97 Quick setting compound confirming to relevant IS make Dr Fixit or equivelent make 98 CONSTR 98 RCC Beams 110x110x1420mm minimum M 25 grade Four nos 8mm dia TMT bars two each on top and bottom with 6mm dia MS bar stirrups spaced at 200mm c c will be provided as reinforcement steel bar make to be used ISI marked only complete all as per drg incl 2 nos MS flat for size 40 mm x 50 mm and 150 mm long nut bolt arrangement 99 CONSTR 99 60MM thick PCC inter locking coloured tiles machine pressed of M 35 grade each tile covering as area 0.0444 m2 conform to relevant IS 100 CONSTR 100 Burnt Clay bricks of standard size confirming to relevant IS minimum crushing strength should not be less then 75 Kg Sqcm sample to be approved before supply 101 CONSTR 101 Dressed stone ready to use for random rubble stone masonary of height varrying from 150mm to 250mm and length not exceeding 3 times height or width 102 CONSTR 102 Load bearing concrete hollow blocks of size 400mm x 200 mm x 200 mm casted in design mix 1 to 2 to 4 to have a strength of M10 to M15 103 ELECT 1 MCB distribution board two way single door 104 ELECT 2 MCB 16 AMPs SP 240V 50Hz 10KA C series confirming to IS 8828 2001 105 ELECT 3 MCB single pole 230V AC 50 Hz 6 Amps 10KA Conforming to relevent IS suitable for lighting & other domestic loads 106 ELECT 4 MCB single pole 230V AC 50 Hz 16 Amps 10KA Conforming to relevent IS, suitable for lighting & other domestic loads 107 ELECT 5 MCB 6 AMPs single pole 240V 50Hz confirming to IS 8828 2001 IEC 60898 2002 make L and T HAVELLS SIEMENS LEGRAND SCHNEIDER Merlin and Gerin 108 ELECT 6 MCB 16 AMP double pole 240V 50Hz 20KA C series confirming to IS 8828 1978 make L and T HAVELLS SIEMENS LEGRAND/ SCHNEIDER Merlin and Gerin 109 ELECT 7 LED Tube light fitting 1 x 18W 4 feet long complete with all accessories including LED tube rod 110 ELECT 8 LED Bulb 7 Watt make Havells Bajaj Philips Syska 111 ELECT 9 Modular socket 6A 2/3 pin combined 2 module 112 ELECT 10 Modular Switch one way 6 AMPs one module confirming to relevant IS 113 ELECT 11 Modular socket 16A 2/3 pin combined 2 module 114 ELECT 12 Modular socket 6A/16A 2/3 pin combined 2 module make Havells Anchor Legrand 115 ELECT 13 Modular switch one way 16 AMP 1 module make Havells/ Anchor/Legrand 116 ELECT 14 PVC Insulated wire 1.5 Sq mm copper conductor single core unsheathed conforming to relevant IS 117 ELECT 15 PVC ceiling rose 2 to 3 terminal confirming relevant IS 118 ELECT 16 PVC casing capping 25 mm x 16mm 119 ELECT 17 PVC L bend 25 mm dia conforming to relevant IS 120 ELECT 18 PVC elbow 25 mm dia conforming to relevant IS 121 ELECT 19 PVC casing capping T 25mm 122 ELECT 20 PVC casing capping square box 4 inch x 4 inch 25mm 123 ELECT 21 PVC rawal plug 124 ELECT 22 PVC body exhaust fan 150mm sweep with lowers 125 ELECT 23 PVC insulated aluminium cable 6 Sqmm 2 core conforming to IS 694 2005 make Havells/ Polycab/Finolex 126 ELECT 24 PVC insulated aluminium cable 2.5 sqmm Twin core conforming to IS 694 2005 make Havells/Polycab/Finolex 127 ELECT 25 PVC insulated aluminium cable 4 sqmm twin core conforming to relevant IS make Havells Polycab/ finolex 128 ELECT 26 PVC saddle clip 20 mm as per approved sample 129 ELECT 27 PVC junction box 2 to 3 way for 20 mm conduit pipe conforming to IS 3419 2001 sample to be approved before supply 130 ELECT 28 PVC body exhaust fan 300mm sweep with louwers make Crompton Khaitan Bajaj Usha 131 ELECT 29 PVC cable insulated 6 sq mm two core with copper conductor suitable up to 1100V conforming to IS 694 2005 make Havells Polycab Finolex 132 ELECT 30 PVC insulated and PVC sheathed wire 1.5 sq mm multistrand Copper conductor suitable up to 1100V conforming to IS 694 2005 make Havells Polycab Finolex 133 ELECT 31 PVC Round block as per approved sample 134 ELECT 32 Rigid PVC conduit pipe dia 25 mm medium grade conforming to relevant IS make Havels PolycabFinolex Anchor 135 ELECT 33 Cable PVC insulated and unsheathed single core with stranded copper conductor suitable up to 1100V conforming to relevent IS of size 2.5 sqmm 136 ELECT 34 Cable PVC insulated and PVC sheathed 1100V grade twin core with stranded aluminium conductor conforming to conforming to relevent IS of size 10 sq mm 137 ELECT 35 Cable PVC insulated and unsheathed single core with stranded copper conductor suitable up to 1100V conforming to relevant IS of size 4.00 sqmm 138 ELECT 36 Flexible wire PVC insulated twin core twisted of size 22/0.0076 with copper conductor 139 ELECT 37 Flexible wire PVC insulated twin core of size 23/0.0076 with copper conductor confirming to relevant IS make Finolex Polycab Havells 140 ELECT 38 Flexible wire PVC insulated twin core twisted of size 22/0.0076 with copper conductor 141 ELECT 39 Tape insulation in 2 cm width 10 mtr long confirming to ISI 12714 142 ELECT 40 Main switch 16 Amp 2 pole 240 volt 50Hz conforming to IS 4064 Pt I and II 2005 make Havells Anchor Legrand 143 ELECT 41 Main switch 32 Amps double conforming to relevant IS 144 ELECT 42 White cover plate with frame 2 module 145 ELECT 43 White cover plate with frame 3 module 146 ELECT 44 White cover plate with frame 4 modulemake Havells Anchor Legrand 147 ELECT 45 Metal flush box 2 Module 148 ELECT 46 Metal flush box 3 Module 149 ELECT 47 Metal flush box 4 Module 150 ELECT 48 MS screw 20 mm confirming to relevant IS pkt of 100 Nos 151 ELECT 49 MS screw 25 mm confirming to relevant IS pkt of 100 Nos 152 ELECT 50 MS screw 15 mm confirming to relevant IS pkt of 100 Nos sample to be approved before supply 153 ELECT 51 CP Screw 20mm 100 Nos Pkt 154 ELECT 52 CP Screw 35mm 100 Nos Pkt 155 ELECT 53 1.5 Sqmm multi strand copper conductor PVC cable conforming to IS make Paragon Kinjal Finolex 156 ELECT 54 Junction box 4 way 20mm PVC conforming to relevant IS sample to be approved before supply 157 ELECT 55 Junction box 4 way 25mm PVC conforming to IS 3419 1976 sample to be approved before supply as per Std 158 ELECT 56 Angle holder with skirt 159 ELECT 57 Change over switch 16 Amps two pole 240 Volts

Refer document

Refer document

INR 1.76 Crore /-