|
| 1 | Micro processor and Micro controller lab |
| 2 | Arduino Trainer Kit -Arduino trainer kit within-built micro controller with on chip bootloader,16x2 alphanumeric LCD Interface,4x4 keypad interface,RS232 UART, I2C EEPROM, I2C RTC, ADC, DAC, Driver for Motors Relays, Motor Driver,4 digit Seven Segment Display interface,8 LEDs for logic verification, LM35 Temperature Sensor , IR Photo Sensor, Pull Up/Pull Down Push to On Switches , Based Object Sensor, Buzzer Interface, 433 MHz RF Module with Encoder-Decoder |
| 3 | 8085 MICROPROCESSOR TRAINING KIT:Based on 8085 CPU operating at 6.144 MHz, 8K bytes of Powerful Monitor Program using 27512 EPROM, 8K bytes of RAM using 6264 with Battery Backup using NICD Battery, On-board one memory expansion up to 56KB, Three Channel Timer/Counter using 8253 brought out at 10 Pins FRC Connector, 48 I/O lines provided through 8255 brought out at 26 Pins FRC Connector to interface with IC-XX Series, RS-232C interface through SID/SOD lines, Two mode of commands: ASCII Key pad Mode and Serial Mode, 20x2 Alphanumeric LCD Display with Backlite, 101 ASCII Keyboard interface using 89C2051 operating @ 12MHz, Powerful Commands like Examine/Edit Memory, Examine/Edit Register, Single stepping, Execution, Block Move, Insert Data, Delete Data can be used through ASCII keyboard or PC serial mode, On board Single Line Assembler / Disassembler, Facility for Downloading/Uploading files from/to PC, All address, data & control lines are available on KXT Bus 50 pin FRC Connector to interface with SC-XX Series, All ICS are mounted on IC Sockets, Bare board Tested Glass Epoxy SMOBC PCB is used, In-Built Power Supply of +5V/1.5A, ±12V/250mA, Attractive Plastic Enclosures, User’s Manual with sample programs. |
| 4 | 8051 Microcontroller Trainer kit -• 8051/89C52 CPU operating @ 11.0592 MHz, 32K user RAM using 62256 with Battery Backup using NICD Battery, 16K bytes of powerful monitor EPROM using 27512, One memory socket is provided for expansion up to 64kB, 48 I/O lines using 2 Nos. of 8255 brought at 26 Pins FRC Connector to interface with IC-XX Series, Three Channel Timer/Counter using 8253 brought out at 10 Pins FRC Connector, 20x2 Alphanumeric LCD Display with Backlite, 101 ASCII Keyboard interface using 89C2051 operating @ 12MHz, Two External interrupts INT0 & INT1 are available at 40 pin FRC connector, RS-232C using RX/TX of 8051 terminated on 9 Pins D-Type Connector, Onboard Single Line Assembler / Disassembler, Two modes of operation: ASCII Keyboard Mode and Serial Mode, Powerful Commands like Examine/Edit Memory, Examine/Edit Register, Single stepping, Execution, Break Point can be used through ASCII keyboard or PC serial mode, Facility for Downloading/Uploading files from/to PC, All Address, Data, Control & Port lines are available on 40 Pins & 10 Pins FRC Connector, All ICS are mounted on IC Sockets, Bare board Tested Glass Epoxy SMOBC PCB is used, In-Built Power Supply of +5V/1.5A, ±12V/250mA, Attractive Plastic Enclosures, User’s Manual with sample programs. |
| 5 | 89MCU51 EMBEDDED TRAINER KIT:Microcontroller• CPU: Philips/Atmel 89Cxx Microcontroller• ISP Programming facilityOnboard Application 8 LEDs to display Digital Output, 8 Switches to give Digital Input each indicated by LED, 16*2 Alphanumeric LCD, 4 digit seven segment displays, I2C compatible, 24C512 EEPROM (64KB), DS1307 RTC with suitable battery, 4 Channel 8bit ADC & 8 bit DAC using PCF8591, Temperature sensor interface Lm35, Temperature sensor interface DS18B20, 24 I/O Lines Provided on a 26 pin FRC Connector for external interface, On board supply +/- 12V, 5V is provided, Supply Input Voltage: 230V AC, User\"s Manual with sample programs for all on board features. |
| 6 | ADC-0809 Interfacing ModuleADC module using ADC-0809, 8 bit accuracy ADC chip, Eight Channel on-chip multiplexed ADC, A/D Conversion time 100 micro sec, SOC, EOC, O/P enable can be accessed by user, Provision of 0 to 5V variable source using Potentiometer for One channel, Eight channel analog inputs are to be provided on Screw Terminals, Connect to 8255 using 26 pin FRC Connector, User\"s Manual with Sample Programs. |
| 7 | DAC-0800 Interfacing ModuleDAC Module using DAC-0800, 8 bit accuracy DAC chip, Dual Channel DAC using 2 Nos. of DAC-0800, DAC Settling time is 100 ns, DAC Output is provided at Two Test Points, Connect to 8255 using 26 pin FRC Connector, User\"s Manual with Sample Programs |
| 8 | Stepper Motor Controller Card with MotorThis Card can Control a Two/Four phase motor, Half Step, Full Step can be controlled using this card, Clock Wise & Anti Clock wise rotations can be controlled, Speed can be controlled by this controller, Facility to control maximum 2Kg cm Motor is provided, 0.25Kg cm Stepper Motor is supplied along with this module, Provision for connecting external 5V/12V supply to drive the motor, Connect to 8255 using 26 pin FRC Connector, User\"s Manual with Sample Programs. |
| 9 | DC Motor Controller Card with MotorDAC-0800 is used for Digital to Analog Conversion, 8 bit accuracy DAC chip, SPDT Relay is provided for direction control, Clock Wise & Anti Clock wise rotation can be controlled, Speed can be controlled by this controller, 9 Volt DC Motor is supplied with this card, 9 Volt AC Adaptor is supplied with this card, Connect to 8255 using 26 pin FRC Connector, User\"s Manual with Sample Programs. |
