Reconstruction Of Damaged Canal Of Payode Anorth Li Scheme In Edavaka Panchayath Urgent Restoration Work Of Electrical Installation And Motor Pump Set
Tender Value
6.07 Lakhs
Estimated cost
Bid Submission
25 Jan 2022
0 days left
EMD
15200
Bank guarantee accepted
Document Fee
1350
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
edavaka → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Reconstruction Of Damaged Canal Of Payode Anorth Li Scheme In Edavaka Panchayath Urgent Restoration Work Of Electrical Installation And Motor Pump Set
BOQ
| Sl. No. | Item Description |
| 1 | Urgent electrical maintenance |
| 2 | od97075/2018_2019 : Charges for removing the mud, sand and other particles deposited due to the natural calamity(flood) from motors, pump, starter ,motor basement etc using suitable tools and water |
| 3 | od97076/2018_2019 : Charges for disconnecting the electric supply, dismantling the Incomer, Bus bar, outgoing swtches, meters etc from the existing main panel board cleaning thoroughly, heating to get the required IR value, scraping,cleaning and painting the whole board with two coats of sinthetic enamel paint over a coat of red oxide primer and refitting the dismantled switches and accessories in position including checking and taping the wires, checking and tightening all connections etc and giving connection.(data) |
| 4 | od97133/2018_2019 : 75HP slip ring motor leading to nearest road side, loading into the vehicle and convey to the workshop including leading, loading and unloading. at work shop , separating the motor, in to stator & rotor,reassembling and convey to pump house and refitting , test run etc as required. |
| 5 | od97080/2018_2019 : Dismantling the 75 HP motorinto stator and rotor, cleaning the the stator and rotor thoroughly usingfresh waterremoving the sand and mud particles from core, coil etc and removing the water and moisture content usingand heating the samefor 6 daysto get required IR value.cleaning the windings, cleaning with petrol, attending minor repairs, retaping the coils if necessary, varnishing the coils with best quality insulation varnish, cleaning and greasing the bearings with Lithium base grease, heating and baking the windings, reassembling, test running including scrapping, cleaning and painting with 2 coats of Grey enamel paint. |
| 6 | od97082/2018_2019 : Dismantling the 75HP oil immersed motor starter, drain out existing transformer oil, cleaning the contacts, attending minor repairs, and refilling the required quantity of best quality transformer oil and replacing the 600v, 50Hz no volt coil and reassembling the same including giving connection, test running etc as required |
| 7 | od97139/2018_2019 : Supply and renewal of Gasket set for pump set in place of damaged one |
| 8 | od97141/2018_2019 : Supply and renewal of Gland packing for pump set in place of damaged one |
| 9 | 1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch |
| 10 | 1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet |
| 11 | 13.10 : Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required |
| 12 | 13.11 : Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required. |
| 13 | 13.13 : Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire. 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KSA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required. |
| 14 | od97083/2018_2019 : Supplying and erection of 11 KV, 400A GO AB Switch suitable for 3 wire. 11 KV overhead lines and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required. |
| 15 | od97084/2018_2019 : Supplying and erection of 11 KV, DO Fuse suitable for 3 wire. 11 KV overhead lines and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required. |
| 16 | od97085/2018_2019 : Painting with synthetic enamel paint over a coat of red oxide primer of approved brand in the existing HT Structure and existing HT fencing etc as required |
| 17 | od97086/2018_2019 : Removing the rusted and corroded portion in the existing HT structure by scrapping and sand papering and preparing the surface smooth including necessary repairs in the structure etc complete |
| 18 | 90.14.10.4 : Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 25/35 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL |
| 19 | 2.2.14 : Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required125 Amp, 36 KA |
| 20 | 90.14.10.6 : Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.125A, 35/36 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based releasewith overload setting of 50 - 100% having adjustable OL & SC |
| 21 | 90.14.10.17 : Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.320A/400A, 50/55 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with microprocessor based releasewith overload setting of 50 - 100% having adjustable OL & SC |
| 22 | 90.14.11.6 : MCCB AccessoriesSupply and fixing 250 - 400Aearth fault module of MCCB with builtin CBCT. |
| 23 | 90.14.11.12 : MCCB AccessoriesSupply and fixing shunt release for all voltage range up to 630A. |
| 24 | 90.14.11.16 : MCCB AccessoriesSupply and fixing rotary handle, Directtype(including BUC handle with door interlock ) in the existing MCCB of rating up to 630A. |
| 25 | 90.14.11.13 : MCCB AccessoriesSupply and fixing rotary handle, External type(including BUC handle with door interlock ) in the existing MCCB of rating up to 250 A |
| 26 | od97088/2018_2019 : Supply, Erection, Testing and Commissioing of outdoor oil filld CTPT unit with bushing as per KSEB standard consist of following: CT Ratio - -/5A 15 VA Class - 0.2 S CTs 3 Nos 11KV/110V 100VA 0.2 S CLASS PT: 1 Nos.CTPT unit as per KSEB standards and including testing at KSEB TMR unit |
| 27 | od97089/2018_2019 : Supply, Erection, Testing and Commissioing of -/5A, class 0.2 S, 4 wire HT TOD meter with terminal block and 20A fuse with HRC Link including testing TOD meter. |
| 28 | od97090/2018_2019 : Supply and fixing 75/5A CL-5P10 neutral CT in existing enclosure |
| 29 | od97091/2018_2019 : Supply and installation of dust and vermin proof outdoor Hensel Mi Boxes with lids IP65 to fix neutral CTas required including fixing it on transformer plinth making good the damages etc as required |
| 30 | od97143/2018_2019 : Supply and installation of dust and vermin proof outdoor Hensel Mi Boxes with hinged lids IP65 to fix TOD meters,terminal block etc as required including fixing it on existing angle iron frame,making good the damages etc as required |
| 31 | 90.12.1.36 : Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium powercable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 300 sq mm |
| 32 | od97093/2018_2019 : Supply & laying of one number PVC insulated and PVC sheathed armoured copper Control cable of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required 4 sqmm 2 core |
| 33 | od97094/2018_2019 : Supply & laying of one number PVC insulated and PVC sheathed armoured copper Control cable of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required. 12 core 2.5 sq mm |
| 34 | od97095/2018_2019 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured copper Control cable, of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 50cms, making good the damages , colour washing etc. as required. 2 core 4 sq mm with factory made clamp |
| 35 | od97096/2018_2019 : Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured copper Control cable, of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 12 core 2.5 sq mm with factory made clamp |
| 36 | od97097/2018_2019 : Supply and drawing 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface / recess conduit as required including giving necessary connections of the following sizes. 50.00 sq.mm 6 Run |
| 37 | od97098/2018_2019 : Supplying and making end termination with brass compression glandfor12Core 2.5Sqmm of PVC insulated and PVC sheathed copper conductor control cable as required. |
| 38 | 9.1.30 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm) |
| 39 | 9.3.27 : Supplying and making straight through joint with cast resin compound including ferrules and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 300 sq. mm |
| 40 | 90.12.10.2 : Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation50/38 mm or nearest size |
| 41 | 90.12.9.13 : Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench200/174 mm or nearest size |
| 42 | 90.14.1.1 : Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 2.00mm CRCA sheet, powder coated (excluding base frame) |
| 43 | 90.14.6 : Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required. |
| 44 | 90.14.2.1 : Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc. |
| 45 | od97099/2018_2019 : supply and fixing Red, Green, blue, Yellow, Orange colours LED indicator, AC/DC, as required |
| 46 | od97100/2018_2019 : Supply and fixing 400/5 A, 5 VA, accuracy class 1, Tape wound Metering CT |
| 47 | od97101/2018_2019 : Supply and fixingDigital Multifunction meter to read: V, A, F, PF-3 phase accuracy class 1 LED |
| 48 | od97102/2018_2019 : Supply and wiring with PVC insulated stranded single core copper conductor cablesfor interconnecting the control devices/ equipments including the wiring firm by suitable tie/ tie mounts/ PVC duct etc as required. 1.5Sqmm single run |
| 49 | od97103/2018_2019 : Supply and wiring with PVC insulated stranded single core copper conductor cablesfor interconnecting the control devices/ equipments including the wiring firm by suitable tie/ tie mounts/ PVC duct etc as required. 4.00Sqmm single run |
| 50 | 90.14.3.2 : Supply and providing heavy duty \"A\" section neoprene gasket in the panel boardU\" section rubber beeding suitable for 1.60/ 2.00 mm sheet |
| 51 | 90.14.5 : Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board |
| 52 | 90.14.7 : Supply and providing copper earth bus in the panel board |
| 53 | od97104/2018_2019 : Providing and fixing earth bus of 25mm X 3 mm copper strip on surface for connections etc. as required. |
| 54 | od97105/2018_2019 : Supplying and laying 32 mm X 6 mm G.Istrip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 55 | od97106/2018_2019 : Providing and fixing 32 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required. |
| 56 | od97107/2018_2019 : Dismantling the existing 200 KVA transformer from plinth and transporting to work shop, opening the top after draining the complete transformer oil from the transformer tank, putting the core-coil assembly in oven (nearly 3-4 days), re tanking the core coil in the tank, filling the oil, filtering the oil, repainting the transformer, including supply and filling the best quality transformer oil and testing the transformer etc. |
| 57 | 14.7 : Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required. |
| 58 | 14.11 : Providing brick work (in width 225 mm or more) with F.P.S. bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) at all levels. |
| 59 | od97108/2018_2019 : Providing and laying in position graded stone aggregate 40 mm nominal size intransformer yard etc as required. |
| 60 | od97110/2018_2019 : Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc,as required, In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, for HT fencing |
| 61 | 2.21 : Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 62 | 2.22 : Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 63 | od97131/2018_2019 : Dismantling the existing wiring with fitting, transporting the same to the section store, including making good the damages on surface colour washing etc. complete as required. |
AI Tender Summary
Tender Timeline
Jan 18, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedJan 25, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJan 29, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender