Construction Of Town Hall ( Netajibhavan ) Under Bhadreswar Municipality ( Civil Part )
Tender Value
5.22 Crore
Estimated cost
Bid Submission
07 Feb 2022
0 days left
EMD
10.45 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
BHADRESWAR → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Town Hall ( Netajibhavan ) Under Bhadreswar Municipality ( Civil Part )
BOQ
| Sl. No. | Item Description |
| 1 | Earthwork in excavation of foundation trenches or drain, in all sorts of soil (including mixed soil but excluding literate or sand stone) including removing spreading or stacking the spoils within a lead of 75m.As directed. The item includes necessary trimming the sides of trenches, leveling and dressing and ramming the bottom, baling out water etc. as required complete.Depth of excavation for additional depth beyond 1,500mm.& 3,000mm but not requiring shoring |
| 2 | Earthwork in filling in foundation trenches or plinth with good earth, in layers not exceeding 150mm. Including watering & ramming etc. layer by layer complete. With earth obtained from excavation of foundation |
| 3 | Filling in foundation or plinth by silver sand in layers not exceeding 150mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. |
| 4 | Pre Construction Anti termite measure Treatment to the back filling of R.C.C. foundation with chemical emulsion by admixing chloropyrofos emulsifiable concentrate (1% concentration) with water by weight at the rate of 7.5 ltr. per sq.m. of the vertical surface of the substructure of each side of the foundation. The work shall be carried out as per specification as described in para 6.3.1 of code IS- 6313 (part-II) 1981 (Mode of measurement will be per sq.m. of vertical area of foundation treated). |
| 5 | Post Construction Anti termite measure Anti-termite treatment to the outside of foundation with chemical emulsion by admixing chloropyrofos emulsifiable concentrate (1% concentration) with water by weight, drilling 12mm. dia holes in concrete or masonry apron at an interval of 300mm. to a depth, of 300mm or more as close to the plinth wall as possible and the chemical emulsion pumped into those holes to soak the soil below at a rate of 2.25 litres per linear metre complete as per specification laid down in para 4.3.1.1 of Code I.S.-6313 (Part-III)-1981. |
| 6 | Brickworks Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 7 | Brick work with 1st class bricks in cement mortar (1:6) In foundation and plinth. 36.4X2+19.12X11.85X2+7.35X1 21.12X5 Staircase |
| 8 | In superstructure, ground floor upto first floor level 36.4X2+19.12X1+8.3+12.3X22.25X2+11.35X18.3X12.3X2 |
| 9 | In first floor upto roof 33.4X2+19.12X11.79X2+7.35X119.12X1 |
| 10 | 125mm thick brick work with first class brick in cement mortar (1:4) in ground floor. |
| 11 | In first floor upto roof |
| 12 | Concrete works Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. |
| 13 | Supplying ready mixed concrete of M 25 Grade with well graded stone chips of 20 mm nominal size containing designed quantity of cement per Cu.m of wet concrete produced in computerised batching plant under controlled condition using approved super plastisizer, designing concrete mix following I.S. 10262 and I.S. 456, transporting the mix with agitation in transit mixer to work site depositing the mix on a platform erected for the purpose at required levels of concreting and then placing the mix in its final location of form work compacting and curing the same complete as per specification & direction of the Engineer-in-charge including computerised batching plant transit mixer with all accessories vibrators etc. inclusive of all other incidental charges in this connection complete but excluding cost of hire charge of platform and its supporting staging which would be paid through separate item. [cement to be supplied by the Manufacturer/ supplier] In Ground Floor and Foundation 41 nos col 2 IsolatedCP1 & CPWith approved concrete pump |
| 14 | In superstructure above tie beam upto first floor incl. slab & beam Col - 41Beam Slab+Stair+ Porch Screen wall 8.3X2X2 Lift well With approved concrete pump |
| 15 | In superstructure above first floor incl. slab & beam Col - 25 Slab - 5.8+5.5+4.075 Staircase - 6.6X3X2 Lintel - Lift well With approved concrete pump |
| 16 | Driven Cast-in-place M25 grade vertical R.C.C. pile of required diameter and required length (length to be measured from the bottom of raft / Pile Cap to the bottom of shoe) including cost of all materials and labour for casting, hoisting, driving etc. and also including cost of dummy lengths of pile and of hire charges of all instruments as necessary but excluding reinforcement complete as per drawing and & Technical Specification. Pile Diameter 500mm - 230 piles |
| 17 | Removal of mud/sludge/slurry/liquid earth obtained during piling work from the working site and disposal of the same beyond the KMC/Municipal or any suitable area with conformity of Municipal Corporation Rules using tanker including loading and unloading the same with pump, clearing the site complete in all respect as per direction of the Engineer-in-charge. Pile Diameter 500mm |
| 18 | Supplying,hoisting,fitting and fixing R.C.C. precast thin lintels, 125 mm. thick (1:1.5:3) conforming to the specification laid down in C.B.R.I. data sheet No.1 with stone chips, sand, cement and reinforcement (both main and distribution) bars upto 1.00 percent as per drawing and specification including placing in situ and supporting arrangement for taking the load of super-imposed brick work and striking of the same when directed. LintelII. Other than SAIL/ TATA/RINL |
| 19 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(When the height of a particular floor is more than 4 m the equivalent floor height shall be taken as 4 m and extra for works beyond the initial 4 m ht. shall be allowed under 12 (e) for every 4 m or part thereof)Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work |
| 20 | Extra for staging beyond 4 m in any floor (Mode of measurement: area in plan X mean height of staging upto soffit of shuttering above initial 4 m) |
| 21 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation and upto roof of ground floor/upto 4 m Ribbed Steel Other than SAIL/ TATA/RINL |
| 22 | For works in first floor Other than SAIL/ TATA/RINL |
| 23 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] With 1:6 cement mortar 20 mm th external plaster |
| 24 | 15 mm th internal plaster |
| 25 | Supplying & laying 3mm thick pre-fabricated plastomeric water proofing membrane conforming to EN 12311-1 & ASTMD 5147, manufactured with atactic poly propylene (APP) modified premium grade asphalt , specially reinforced with non-woven polyester core with polyester reinforcement @160 gms per sqm & both faces covered with thermo-fusible polyethylene film /MineraL on top face over a coat of primer @ 0.40 lit/sqm of manufacturer\"s specification on smooth,clean dry surface prepared wherever required.Lap joint shall be provided of 75 mm in longitudinal & 100 mm in transverse direction and fused using LPG/ Propane torch employing extra care ensuring full bondage, complete removal of entrapped air and sealing edges into grooves in appropriate manner as per direction of Engineer -in-charge all complete including materials,labour and applicable taxes. (Payment shall be made on the basis of finished surface area.). Membrane Property: Softening Point > 150 deg C, Cold Flexibility < -6 deg C, Tensile Strength, N/cm : 600 (longitudinal), 450 (transverse), Tearing Strength, N: 300 (longitudinal), 200 (transverse)3.95X19.125+4.3X7.35+11*3.4 |
| 26 | Flooring 18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in car parking area including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in - charge to match with the existing work. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @2.0 kg/Sq.m] |
| 27 | Supplying, fitting and fixing Marble Slab/tile of 15 to 18 mm thickness in stair, landing risers & treads etc. over 20 mm (av.) thck base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/Sq.m before placing marble & jointed with white cement slurry @ 2.0 kg/Sq.m with necessary pigments including grinding and Granite polishing as per direction of Engineering -in -Charge in Ground Floor. {White cement and Pigment to be supplied by the Agency] With Makrana plain pink / Adranga Pink / Garbh Gulabi / Udaypur pink / Udaypur Green / Black Bhaslana Area of each Slab/tile exceeding 0.60 sq.m but not exceeding 1.00 sq.m. |
| 28 | Supplying,fitting & fixing granite slab 15mm to 18mm thick in entrance lobby over 20mm (avg) thick base of cement morter (1:2) laid with white cement slurry @ 4.40Kg per Square meter before placing of granite and jointed with white cement slurry @ 2.0 Kg per square meter with necessary pigments and complete as per direction of Engineer-in-charge including cost of all materials, labours, curing and roughening of concrete surface complete.In ground floor Area of each Granite slab above 1.00 Square meter. |
| 29 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by syntheticadhesive & grout materials etc. WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. Area of each tile upto 0.09 Sq.m Other than Coloured decorative including white |
| 30 | Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqMor using polymerised adhesive(6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer\"s specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contr] With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment. (5.375X4.35+1.2X1.5+2.75X1.5)X9+2.29X4.3529.815X1.57.7X4.87+4.575X4.873.7X12.97+1.95X11.77 Light color |
| 31 | Supplying & laying as per IRC-SP:063-2004 paver unit of any shade of approved quality as per relevant IS code, laid in pattern as directed in pavement, footpath, driveway (paver block only), etc including necessary underlay complete in all respect with all labour and material. [Border concrete if necessary to be paid separately]. Note: Sub-grade CBR should not be less than 5. 25 mm thick Tiles as per IS: 1237-2012 for footpath,ramp,staircase of public building(over 25 mm thick (Avg) Cement mortar (1:3) & Cement Slurry @ 4.4 kg/Sq.m at back side of Block. Cement for Mortar & Slurry to be supplied by Department).Grey Area of land = 1437.0 sqm Cov. Area of building = 709.0 sqm |
| 32 | Finishing works Grill works M.S. works in framed gratings of window etc.made of round or square bars and frame work or M.S. flats (with the bars securely fixed to the flat bar frame) with or without intermediate flat bar stiffener and fixed with necessary screws etc. complete, as directed. Grill weight considered = 13kg / sqmIn ground floor |
| 33 | In first floor |
| 34 | Wood & PVC works Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected upto three decimals).Sal : Malayasian |
| 35 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut attwo corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc.complete as per Manufacturer?s specification and direction of Engineer-in-Charge. |
| 36 | Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings. 35 mm thick shutters (single leaf) Gr floor 10 |
| 37 | 35 mm thick shutters (single leaf) First floor |
| 38 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together withsolvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge. In ground floor. 5 |
| 39 | In first floor 2 |
| 40 | Painting works Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. Solvent based Interior Grade Acrylic primerIn ground floor. |
| 41 | Solvent based Interior Grade Acrylic primer In first floor |
| 42 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of theEngineer in Charge In ground floor two coats |
| 43 | In first floor two coats |
| 44 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.Premium 100% Acrylic Emulsion (interiors) Ground floor |
| 45 | First floor |
| 46 | Premium 100% Acrylic Emulsion (exteriors) Ground floor |
| 47 | First floor |
| 48 | Windows Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive,joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket, locking arrangement and rollers. In ground floor |
| 49 | Fully glazed single leaf reamless swing door made of anodized aluminium alloy extrusions fabrication after cutting to proper shape and size, drilling and aligning fitted with heavy duty hydraulic action floor spring with top pin assembly and fitted with inbuiltlocking arrangement and all other necessary fittings, fixture, adhesives and joineries, cutting the glass to requisite shape and size mounting the edges for fitting the same with dry set neoprine/EPDM gasket. |
| 50 | Miscellaneous R.C. Water Tank incl Fire TankEarthwork in excavation of foundation trenches or drain, in all sorts of soil (including mixed soil but excluding literate or sand stone) including removing spreading or stacking the spoils within a lead of 75m.As directed. The item includes necessary trimming the sides of trenches, leveling and dressing and ramming the bottom, baling out water etc. as required complete.Depth of excavation for additional depth beyond 1,500mm.& 3,000mm but not requiring shoring |
| 51 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 52 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in water tank bed as per relevant IS codes. |
| 53 | Controlled Cement concrete with well graded stone chips (20 mm graded nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption willbe determined on the basis of preliminary test and job mix foumula. In ground floor and foundation. [using concrete mixture] M 20 GradePakur Variety |
| 54 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] 20 mm th plaster |
| 55 | Supplying & laying 3mm thick pre-fabricated plastomeric water proofing membrane conforming to EN 12311-1 & ASTMD 5147, manufactured with atactic poly propylene (APP) modified premium grade asphalt , specially reinforced with non-woven polyester core with polyester reinforcement @160 gms per sqm & both faces covered with thermo-fusible polyethylene film /MineraL on top face over a coat of primer @ 0.40 lit/sqm of manufacturer\"s specification on smooth,clean dry surface prepared wherever required.Lap joint shall be provided of 75 mm in longitudinal & 100 mm in transverse direction and fused using LPG/ Propane torch employing extra care ensuring full bondage, complete removal of entrapped air and sealing edges into grooves in appropriate manner as per direction of Engineer -in-charge all complete including materials,labour and applicable taxes. (Payment shall be made on the basis of finished surface area.). Membrane Property: Softening Point > 150 deg C, Cold Flexibility < -6 deg C, Tensile Strength, N/cm : 600 (longitudinal), 450 (transverse), Tearing Strength, N: 300 (longitudinal), 200 (transverse) |
| 56 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation and upto roof of ground floor/upto 4 m Ribbed Steel Other than SAIL/ TATA/RINL |
| 57 | Supplying,fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials.) First floor (a)15 mm dia. medium quality for concealed work WC of both Gents and ladies ,For Gents urinal,For Hand wash basin, Ladies wand wash basin, Green room toilet, Ground floor Bath, WC & Hand wash basin of Guests, Kitchen |
| 58 | (b)20 mm dia. medium quality for concealed work From roof to auditorium toilet toilet , Gents toilet, Ladies toilet, Ground floor guests toilets, Green room toilet, |
| 59 | (c)25 mm dia. medium quality for concealed work Drop for first floor toiletDrop for ground floor tpilets |
| 60 | (d) 25 mm dia. medium quality Exposed work Interconnection of tank at roof upto drop |
| 61 | e) 100 mm dia medium quality Exposed work Over flow pipe Delivery line |
| 62 | Supplying,fitting and fixing in position G.I.pipes of TATA make for underground works with all necessary accessories,specials viz.socket,bend, tee,union, cross, elbow,nipple,short piece etc.including cost of all materials,jointing materials ,cutting pipes,making threads,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories , specials.)(d)100 mm dia. medium quality Delivery at ground |
| 63 | Supplying, fitting and fixing showerofapproved brand and make.a) Chromium plated round shower with revolving joints 100 mm dia with ribid cleaning system ( Equvalent code no. 542(N) & Model Tropical/Sumthing Special of ESSCO or similar i) in Gueststoilet |
| 64 | b) Chromium platedshower arm 240 mm long ( Equvalent code no. 536(A) & Model Tropical/Sumthing Special of ESSCO or similar |
| 65 | c) Chromium platedhand shower 70 mm dia round shape single flowwith flexable tubes and fittings ( Equvalent code no. 5037 & Model Tropical/Sumthing Special of ESSCO or similar i) in officers toilet |
| 66 | d) Chromium plateddouble coat hook( Equvalent code no. 35761 & Model KUBIX of Jaquar or similar i) in officers toilet |
| 67 | e) Hand Shower (Health Faucet) with inter flexable tube with wall hook (Equivalent to code no. 573 & Model- ALLIED of Jaquar or similar) i) in officers toilet |
| 68 | Supplying, fitting and fixing Peet\"s valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.).a) 100 mm dia |
| 69 | b) 25 mm dia |
| 70 | c) 20 mm dia |
| 71 | Supplying, fitting and fixingstop cock/ bib cock a) Chromium plated Bib Cock short body ( Equvalent code no. 511 & Model Tropical/Sumthing Special of ESSCO or similar |
| 72 | b) Chromium plated concealed Stop Cock heavy duty ( Equvalent code no. 5083 & Model Tropical/Sumthing Special of ESSCO or similar |
| 73 | Supplying ,fitting and fixing Cast iron soil pipe only conforming to I.S. 3989 / 1970 and I.S. 1729/1964 with bobbins, nails etc. including making holes in the wall, floor etc. and cutting trenches etc. in any floor through masonry concrete, if necessary, and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete. with lead caulked joints(i)150 mm nominal dia. |
| 74 | ii) 100 mm nominal dia Staff toilet, First floor, from first floor to ground floor, Ground floor, To pit |
| 75 | iii) 75 mm Antisyphonage pipe |
| 76 | Supplying, fitting and fixing C.I. holder bat clamp including cutting holes in wall etc. and mending good all damages in cement concrete with jhama chips (4:2:1) and cement plaster (6:1) to match and curing complete in all respect.a) 100 mm dia |
| 77 | b) 80 mm dia |
| 78 | Supplying, fitting and fixing 10 litre porcelain low-down cistern of approved make with either side or bottom inlet, side overflow, brackets complete with all internnal fittings.(i) White |
| 79 | Supplying PVC water storage tank of approved quality with closed top with lid ( Black)- Multilayer a) 5000 litre capacity |
| 80 | b) Labour for hoisting of plastic water storage tank |
| 81 | c) Labour for punching hole in plastic water storage work upto 50 mm dia |
| 82 | Supplying,fitting and fixing vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.(i) 550 mm X 400 mm size |
| 83 | Supplying,fitting and fixing approved brand P.V.C.CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.a) 450 long |
| 84 | Supplying,fitting and fixing approved brand P.V.C.waste pipe, with coupling at one end fitted with C.P. over brassnut, 32 mm dia. A) 750 long |
| 85 | H.C.I. bend with door conforming to I.S.S. including jointing complete.A) with lead caulked joint |
| 86 | Cast iron double branch equal with door conforming to I.S. 1729/1970 including jointing and painting two coats to the exposed surface complete.a) 100 mm dia With lead caulked joint |
| 87 | Supplying, fitting and fixing Approved patent vent cowl I.C.I. conforming to I.S.S. and painting two coats to the exposed surface with approved paint completei) 75 mm |
| 88 | Supplying,fitting and fixing cast iron \"P\" or \"S\" trap conformimg to I.S. 3989 / 1970 and 1729 / 1964 including lead caulked joints and painting two coats to the exposed surface.100 mm dia(A) \"P\" Trap |
| 89 | Supplying,fitting and fixing cast iron Extension pipe conformimg to I.S. 3989 / 1970 and 1729 / 1964 including lead caulked joints and painting two coats to the exposed surface.i) 100 mm X450mm |
| 90 | Supplying,fitting and fixing with cement jointing (3:1) salt glazed stoneware pipe including excavation of earth upto 1.5 metre depth in all sorts of soil both mixed and unmixed and refilling i) 150 mm dia |
| 91 | Supplying,fitting and fixing Aluminium domical gratings i) 100 mm dia |
| 92 | Anglo-Indian W.C. in white glazed vitreous china ware of approved make supplied, fitted and fixed complete in position with necessary bolts, nuts etc (a) With \"P\" trap (with vent) |
| 93 | Flat back urinal (half stall urinal) in whitevitreous chinaware of approved make supplied, fitted and fixed in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete.(i) 635 mm X 395 mm X 420 mm |
| 94 | Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws supplied, fitted and fixed complete.(a) E.P.W.C.(i)Bestonite (Solid type) White |
| 95 | Supplying porcelain partition wall of approved make of size 618 mm X 310 mm and fitting and fixing the same complete in all respect. |
| 96 | Supplying,fitting and fixing glass shelf with aluminium guard rails.(a) Ordinary type with 5.5 mm sheet glass (ii) 600 mm X 125 mm |
| 97 | Supplying, fitting and fixing liquid soap holder.(a) Cromium plated |
| 98 | Supplying, fitting and fixing mirror 5.5mm thick, frame size 550mm x 400mm |
| 99 | Supplying, fitting and fixing towel rail with two brackets.(a) C.P. over brass(i) 25 mm dia. and 600 mm long |
| 100 | Supplying,fitting and fixing porcelain toilet paper holder of approved make with wooden spindle as necessary.(i) Roll type size 250 mm X 125 mm |
| 101 | Supplying,fitting and fixing porcelain soap tray of approved make.\"(i) Recess soap tray size150mm X150mm |
| 102 | Constructing Inspection pit to a depth of 1.5 metre (inside), 250 mm thick 1st class brick work (6:1) in all sides over a layer of jhama brick soling and 150 mm thick cement concrete with jhama khoa (6:3:1) including necessary earth work, fitting and fixing approved type S.W. master trap, constructing masonry invert with cement concrete (4:2:1) with jhama chips, plastering inside and outside(outside upto 300 mm below G.L.) with 19 mm thick cement plastering(4:1) and neat cement punning,including supplying,fitting and fixing one 560 mm.dia R.C.C. manhole cover of approved make with R.C.C. slab of 100 mm thick with cement concrete (4:2:1) with stone chips including necessary reinforcement(upto 1%) and shuttering and necessary corbelling brick work (6:1) so that the R.C.C. cover slab rests 150 mm above adjucent G.L., cement plaster(4:1) 6 mm thick on all external surfaces of the top slab as directed complete in all respect and removal of surplus earth with all costs of labour and materials (xcluding the cost omaster trap only). |
| 103 | Septic tank Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C.manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.Code. (iv) For 50 users A) With Pakur variety. (SAIL/TATA/RINL) |
| 104 | Site development & Landscaping Horticulture Supplying and stacking of good earth (adequate for horticulture work) at site including royalty (earth measured in stack will be reduced by 20% for payment) |
| 105 | Supplying and fixing grass tiles of Mexican Grass Carpet/Selection No. 1 Healthy & fresh grasses (size 1\"x1\" or bigger) including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from wees and fit for mowing including supplying good earth as required by Engineer-in-charge. (Rate includes supply of labour, tools & plants including materials) |
| 106 | Planting of trees ( Avenue plants) in 0.60m dia holes, 1mdeep dug in the ground, mixing the soil with decayed farm yard/sludge manure. This includes supply of labour, tools & plants including materials but excluding cost of tree. |
| 107 | Supplying and Planting of different plant / trees ( Supplying well grown plants bushy and healthy, minimum height as specified i.e. exposed height including all leads & lift, carriage, handling, manuring, applying presticide and fertilizer etc. China palm of leaves 4-5 in earthen pots size 25cm |
| 108 | Areca Palm |
| 109 | Site Development Supplying & laying as per IRC-SP:063-2004 paver unit of any shade of approved quality as per relevant IS code, laid in pattern as directed in pavement, footpath, driveway (paver block only), etc including necessary underlay complete in all respect with all labour and material. [Border concrete if necessary to be paid separately]. Note: Sub-grade CBR should not be less than 5.50 mm thick interlocking designer concrete paver block M-30 grade for non-traffic zone,buiding premises,garden,parks,domestic drive as per IS: 15658- 2006(over 20-30 mm medium sand bed on 200mm thk bound gnaular /granular base course including cost of sand for sand bed but excluding cost of base course & subgrade preparation.) Coloured Decorative |
| 110 | Controlled Cement concrete with well graded stone chips (20 mm graded nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] M 20 Grade |
| 111 | Roof Shed Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) In Roof0.8mm thick sheet |
| 112 | Galvanised iron sheet ridging fitted with necessary bolts, screws, washers etc complete.(225mm end lapping)300 mm lapping each way0.8mm thick sheet |
| 113 | M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-inchargecomplete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erectionall complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof.For Structural Works in Roof Trusses etc. using joists, channels and angles of specified section weighing less than 22.5 kg/ m |
| 114 | Providing double gathered verticalwinding Vertical curtain mechanism system consisting 1H.P./1.5 H.P. 3 phase 440 V motor(Crompton/NEC make), reduction gear mechanism, limit Switch controls, winding pullies, emergency Handle, steel ropes etc.. complete with velvet/Cotton satin cloth screen complete |
| 115 | Providing MS32mm OD hollow pipe bar for frill with 100 mmdia. 1way, 2way, 3way pulleys properly fixed on grid structures with 10mm dia cotton rope manually operated with winchmechanism complete |
| 116 | Providing freel for masking with satin black Markin cloth with hessian lining complete |
| 117 | Providing wing mechanism with horizontal traveling arrangement consisting 42 OD MS pipe, pullies, roller, rope along with satin black double gathered cloth complete |
| 118 | Providing motorised light bars and free bar with 48 OD MS pipe consisting 1.5H.P, 3 Phase 440V motor (Crompton/NEC make), reduction Gear mechanism, limit switch box, steel wire complete |
| 119 | Providing black mid 7rear curtain mechanism Consisting M.S. “T” channel fabricated pathway,Pullies, runners, 1H.P. 3 phase motor, reduction Gear, limit switch box, wire winding pullies,Emergency handle, steel rope etc.. complete With double gathered cotton satin cloth. |
| 120 | Providing cyclorama screen with frame Structure made with 48mm dia and 30mm dia MS hollow pipe, complete with white cyclorama Screen complete. |
| 121 | Providing stage top grid structure made of 50mm X 6mm MS angle and50mm dia heavy Pipe for fixing pullys and other mechanism Of stagecraft along with necessary platform Made of 25mm ply for fixing up mechanism |
| 122 | Providing stage floor with 1800X150X40mm pine wood planks on 100 X 75mm sal wood runners over 125 X 100mm sal wood beam complete with polishing.The upper pine wood plank will have “L” groove on both side to fix one with another in a regular pattern. |
| 123 | P&F of MS Angle & pipe fabricated Catwalk with 25mm ply on the pathway |
| 124 | Auditorium Seat for 500 capacity P&FSemi luxorious 50mm PU foam & fabricUpholstery fitted with PVC handle Auditoriumseat. |
| 125 | P&F Luxorius hi-back 100mm PU foam fitted Fabric upholstery fited with PVC handleV.I.P seat |
| 126 | P&F 6mm thick jute carpet for audi flooring |
| 127 | P&F cabinet with commercial ply & laminates |
| 128 | P&F clear glass mirror |
| 129 | 50mm foam fitted 18X18 inch size seat for green room |
| 130 | 2 Tr Split AC for green room |
| 131 | Lights for green room |
| 132 | Providing both side wall acoustic treatmentwith fine fissured tengular edge mineral fibre board of 12.5mm thick wrapped with decorativefabric on GI frame with 25mm 16kg/m3 density Glasswool backing with chicken mess support(side wall upper part acoustic treatment) |
| 133 | Providing Acoustical false ceiling with aCombination of plain gypsum board of 12.5mm & pinhole Mineral fibre 15mm acoustic boardsIn GI frame. |
| 134 | Providing back wall acoustic treatment with fine fissured tengular edge mineral fibre board of 12.5mm thick wrapped with decorative fabric on GI frame with 50mm 32kg/m3 density Glasswool backing with chicken mess support.(Back wall upper part acoustic treatment) |
| 135 | Side wall & back wall skirtingfor LFAcoustic treatment upto 3 ft from the ground level with 12mm BWR Ply to be fixed on GI frame with 3mm teackwood finish veneer to be pasted on the ply along with polishing complete. |
| 136 | Providing Heavy drapery on doors |
| 137 | Providing insulation of ceiling with 50mm Thermocol fixed with proper hanger under the truss |
| 138 | Double bed with laminted commercial ply |
| 139 | Side table |
| 140 | Head board |
| 141 | Cabinet with laminated commercial ply |
| 142 | Center table |
| 143 | T.V. Cabinet |
| 144 | Single seater sofa |
| 145 | False ceiling with gyp board with drop & traydesign |
| 146 | Curtains |
| 147 | Furnishings, mattress |
| 148 | GST |
| 149 | Cess |
AI Tender Summary
Tender Timeline
Jan 12, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 07, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 10, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender