|
| 1 | 1. CIVIL WORKS |
| 2 | 2.31Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared |
| 3 | 2.6.1Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavatedearth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds ofsoil |
| 4 | 4.1.8Providing and laying in position cement concrete of specified grade excluding the cost of centering andshuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40nominal size) |
| 5 | 60.7.1DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good qualityblasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site |
| 6 | 7.1.1Random rubble masonry with hard stone in foundation and plinth including levelling up with cementconcrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinthlevel with:Cement mortar 1:6 (1 cement : 6 coarse sand ) |
| 7 | 2.25Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers notexceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 mand lift up to 1.5 m. |
| 8 | 5.9.5Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams,girders bressumers and cantilevers |
| 9 | 5.9.1Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases ofcolumns, etc for mass concrete |
| 10 | 5.1.3Providing and laying in position specified grade of reinforced cement concrete, excluding the cost ofcentering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarsesand : 4 graded stone aggregate 20mm nominal size) |
| 11 | 5.1.2Providing and laying in position specified grade of reinforced cement concrete, excluding the cost ofcentering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarsesand :3 graded stone aggregate 20 mm nominal size |
| 12 | 5.22.6Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position andbinding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 13 | 50.6.1.1Solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest availablesize confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete |
| 14 | STRUCTURE |
| 15 | 50.6.1.2Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete. |
| 16 | 50.6.1.8Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand etc complete |
| 17 | 50.6.3.1Solid block masonry using pre cast solid blocks ( Factory made) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth for 10 cm thick wall in CM 1:6 ( 1cement : 6 coarse sand) including cost of scaffolding etc complete |
| 18 | 5.9.5Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams,girders bressumers and cantilevers |
| 19 | 5.9.6Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers,Abutments, Posts and Struts |
| 20 | 5.9.3Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs,landings, balconies and access platform |
| 21 | 5.2.2Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinthand string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five levelexcluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size) |
| 22 | 5.3Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size). |
| 23 | 5.22A.6Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position andbinding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more |
| 24 | 13.7.112 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand) |
| 25 | 13.16.16 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand) |
| 26 | 13.1.112 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 27 | 11.41.2Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. |
| 28 | 11.19.4Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed withneat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishingcomplete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand):Ordinary cement withoutany pigment |
| 29 | 11.37Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory,Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), includingpointing the joints with white cement and matching pigment etc., complete. |
| 30 | 8.31Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specifiedby the manufacturer), of approved make, in all colours,shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge,in skirting, risers of steps and dados, over 12 mm thick bed of cementmortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm,including pointing in white cement mixed with pigment of matchingshade complete. |
| 31 | 8.2.2.2Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machinecut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarsesand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, includingrubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Areaof slab over 0.50 sqm |
| 32 | 50.9.1.1Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framedand fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs ordash fastener shall be paid for separately), using good quality Anjili wood /jack wood |
| 33 | 21.1.1.2Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereverrequired including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron). |
| 34 | od175487/2021_2022Providing and fixing pressed Steel windows and Ventilators made out of 16G (1.5mm) thick prime qualityTATA Galvano Steel sheets using profiles 82 x 60 or 62x42mm for window frames welded or assembledwith 75 mm stainless steel butt hinges, adjustable hold fasts, mortar guards, stainless steel HooksEyes,stay , aluminium beading with screws etc. and welded or assembled with MS Grill of Dia 12 mm rod@100mmC/C horizontally with 30x5 flat vertically per panel or as specified and inclusive of labourcharges for fixing all window fittings duly filled with concrete mix etc , and applied with suitable primer andthen painted with polyurethane paint of desired colour or applied with Powder coating. |
| 35 | od175488/2021_2022Fixing standard steel glazing in doors, windows and ventilators , including fixing of float glass panes of4mm thickness etc complete. |
| 36 | 21.3.2Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness |
| 37 | 9.121Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mmhaving single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall bemoulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. |
| 38 | 9.122.2Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush doorshutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin,moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places forfixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineer-in-charge. |
| 39 | 9.84Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (havingbrand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door widthform 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc.complete. |
| 40 | 21.13Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors includingnecessary cutting and making good etc. complete |
| 41 | 9.48.2Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square orround bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ woodenframes with rawl plugs screws etc.. |
| 42 | 13.85.1Applying priming coats with primer of approved brand and manufacture, having low VOC ( VolatileOrganic Compound) content.With ready mixed pink or grey primer on wood work (hard and soft wood )having VOC content less than 50 grams/ litre |
| 43 | 13.61.1Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two ormore coats on new work |
| 44 | 10.28Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 45 | 13.43.1Applying one coat of water thinnable cement primer of approved brand and manufacture on wallsurface:Water thinnable cement primer |
| 46 | 13.60.1Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Twoor more coats on new work |
| 47 | 10.6.1Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlockedtogether through their entire length and jointed together at the end by end locks, mounted on speciallydesigned pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wiresprings manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thicktop cover |
| 48 | 10.7Providing and fixing ball bearing for rolling shutters. |
| 49 | od177591/2021_2022Supplying and fixing name board with emblem using acrylic sheet base with Reflective type sticker as perrequired shade and color etc complete.
Size of Board 3.00mx 0.60m |
| 50 | od177609/2021_2022Name Board |
| 51 | 1. Plumbing works |
| 52 | 17.3.2Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mmflush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.c. pan with ISI marked black solid plastic seat and lid |
| 53 | 18.53.1Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved qualityconforming to IS: 893115 mm nominal bore |
| 54 | 18.32.1Constructing masonry chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed incement concrete slab 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominalsize), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stoneaggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand)12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5 |
| 55 | 18.35.1Constructing masonry chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4coarse sand) for sluice valve, with C.I surface box 100 mm top diameter, 160 mm bottom diameter and180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 gradesstone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement :5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar1:3 ( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 56 | 17.7.2Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass wasteof standard pattern, including painting of fittings and brackets, cutting and making good the wallswherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brasspillar tap |
| 57 | 17.73.2Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screwswith concealed fitting arrangement of approved quality and colour600 mm long towel rail with total lengthof 645 mm, width 78 mm and effective height of 88 mm, weighting not less than 190 gms |
| 58 | 18.51.1Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards andweighing not less than 690 gms.15 mm nominal bore |
| 59 | 18.16.1Providing and fixing brass stop cock of approved quality :15 mm nominal bore |
| 60 | 18.65Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mmwith concealed fittings arrangements, weighing not less than 106 gms. |
| 61 | 17.32.2Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size withplastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangularshape 453x357 mm |
| 62 | 18.48AProviding and fixing rectangular high density polyethylene water storageloft tank with cover, conforming to ISI : 12701, colour of opaque white or asapproved by Engineer-in-charge. The rate includes making necessary holesfor inlet, outlet & over flow pipes. The base support i/c fittings & fixtures fortank shall be paid separately. |
| 63 | 50.18.7.2.1Providing and fixing PVC pipes, fittings including fixing the pipe with claps at 1.00 metre spacing. Thisincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete asper direction of Engineer-in-Charge 20 mm dia 12Kgf/cm2 - Internal work - Exposed on wall |
| 64 | 50.18.7.6.1Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. Thisincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete asper direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall |
| 65 | 50.18.9.9.1Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching,refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2 |
| 66 | 50.17.1.5Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. |
| 67 | 50.18.9.22.1Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow |
| 68 | 50.18.9.22.4Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend |
| 69 | od191481/2020_2021Providing and fixing 150mm silt with CP gratings |
| 70 | 1.Electrical works |
| 71 | 1.10.3Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulatedcopper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copperconductor single core cable etc as required.Group C |
| 72 | 1.12Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single corecable insurface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulatedcopperconductor single core cable for loop earthing as required. |
| 73 | 2.3.2Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V,on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8way, Double door |
| 74 | 90.11.1.21Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure ofMCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall ,making good the damages, colour washing etc. as required12 way (8+12) - double cover TPN vertical DBwith provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43) |
| 75 | 1.24.3Supplying and fixing following modular switch/ socket on the existing modular plate & switch boxincluding connections but excluding modular plate etc. as required.15/16 amp switch |
| 76 | 1.24.5Supplying and fixing following modular switch/ socket on the existing modular plate & switch boxincluding connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet |
| 77 | 1.14.2Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulatedcopper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 78 | 1.25Supplying and fixing two module stepped type electronic fan regulator on the existing modular plateswitch box including connections but excluding modular plate etc. as required. |
| 79 | 5.19Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existingsurface/ recessed conduit/ submain wiring/ cable as required. |
| 80 | 5.4Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, andprovidingmasonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.with charcoal/ coke and salt as required. |
| 81 | 1.27.2Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modularswitches in recess etc.. As required. 3 module (100 x 75 mm) |
| 82 | 1.28.2Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. asrequired.3 Module |
| 83 | 1.26Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modularplate as required. |
| 84 | 1.14.4Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulatedcopper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 6 Sq.mm + 1 x 6 sq.mm earth wire |
| 85 | 1.14.6Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulatedcopper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 16sq. mm + 1 X 6 sq. mm earth wire |
| 86 | 2.14.3Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residualcurrentcircuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps |
| 87 | od191475/2020_2021Supplying and fixing 6 A to 32 A ratings, SP MCB, and other accessories |
| 88 | 1.14.1Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulatedcopper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 89 | 2.13.2Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete withconnections, testing and commissioning etc. as required.63 amps |
| 90 | od174769/2021_2022Supplying and fixing following 32 amps modular DP switch and other accessories etc complete |
| 91 | od191476/2020_2021Supplying and fixing angle batten with 23 watts CFL and other acessories |
| 92 | od191477/2020_2021Supplying and fixing single tube set ( electronics) and other accessories |
| 93 | od191478/2020_2021Supplying and fixing 48\" ceiling fan and other accessories |
| 94 | od174773/2021_2022Supplying and fixing 12 \" Exhaust fan and other accessories |
| 95 | od191479/2020_2021Supply, installation, testing and commissioning of wall mounted Three Phase 4 wire Energy meter withpoly carbonate body having range of 10-63A, with enclosure made out of powder coated 16 SWG CRCAsheet suitable for fixing in surface/recess with 3 nos. of 63A HRC fuses,63A TPN isolator,neutral link, itsinter connections etc.The enclosure shall have lockable door with glass window and all mountingaccessories etc. complete as required (supply of energy meter is under KSEB scope). |
| 96 | NETWORKING AND TELEPHONE CABLING |
| 97 | od164966/2021_2022Providing network cabling using cat 6 cable through 1\" case and caping and giving conncetion includingall labour charges materialcost,grimping and connecting etc, complete |
| 98 | od164968/2021_2022Engaged a computer engineer for programming all network and commisioning etc. complete (1 Racks X 2000 = 2000) |
| 99 | od164969/2021_2022Supplying and fixing PATCH CORD 0.50M on bottom and grimping two ends |
| 100 | od164972/2021_2022Supplying and fixing PATCH CORD 0.50M on top and grimping two ends |
| 101 | od164973/2021_2022Supplying and fixing 3M PATCH CORD and grimping two ends |
| 102 | od164974/2021_2022Supplying and fixing 2M PATCH CORD and grimping two ends |
| 103 | od164975/2021_2022Supplying and fixing 1M PATCH CORD and grimping two ends |
| 104 | od164976/2021_2022Supplying and fixing patch pannel and giving connection |
| 105 | od164977/2021_2022Supplying and fixing 16 port switch and giving connection. |
| 106 | od164978/2021_2022Supplying and fixing 4U rack and giving connection |
| 107 | od164979/2021_2022Supplying fixing roset box and grimping the ends etc.complete |
| 108 | od164965/2021_2022Supplying and drawing two pair telephone cable through 1\"\" case and caping and giving connection |
| 109 | od164967/2021_2022Suppluing and fixing IO box set and giving connection |
| 110 | od164970/2021_2022Supplying and fixing rose set box and giving connection |
| 111 | od164971/2021_2022Suplying and fixing ordinary type telephone (BPL make) and other assessories |
