|
| 1 | SERVO COMPUTERIZED- UNIVERSAL TESTING MACHINES,1200 KN CAPACITY WITH MECHANICAL EXTENSOMETER + COMPUTER AND PRINTER +ELECTRONIC EXTENSOMETER | Computer Controlled Universal Testing Machine • Electronic Universal Testing Machine with Microprocessor based PC Interface system yielding Servo controlled operation For detailed specification follow the uploaded PDF File. |
| 2 | STANDARD - ROCKWELL HARDNESS TESTING MACHINES ( ANALOG ) | Compliance with following International Standards1. IS:1586-2000, BS:891 (Part 1 & 2) ASTM E-18 for Rockwell test.Salient FeaturesRockwell Hardness testerAutomatic load selection with automatic zero setting dial gaugeAdditional load of 250 kgf with 5mm ball indenter for testing hardness of non ferrous metal.Supplied complete with the following accessoriesTesting Table 50mm dia- 1 NoTesting table 38mm dia with `V` groove for round job 6 to 45mm dia- 1 NoDiamond indenter 120 degreeSteel Ball indenter 1/16\"Test block Rockwell `C`Test block Rockwell `B`Clamping device - 1 NoDash pot oil - 1 bottleRubber bellow for elevating screw protection - 1 NoTechnical Specification•Loads : 60, 100, 150, 187.5, 250 kgf•Initial Load : 10 kgf•Max. test height : 230mm•Depth of throat : 133mm•Max. Depth of elevating screw below base 230 mm |
| 3 | FATIGUE TESTING MACHINES | A rotating beam type machine where load is applied in reverse bending manner. Standard 8 mm dia. Specimen is held inspecial holders at its ends and loaded such that it experiences a uniform bending moment. Specimen is rotated at 4200 RPM by a Motor. A complete cycle of reversed stress in all fibers of the specimen is produced during each revolution. The bending moment is applied through a lever system and can easily be changed by moving a weight Over a lever.Should have following Features• Light weight, • compact size, • simple design• Table model. No need of foundation• Simple lever system for changing load• Accurately calibrated as per IS 5075• Machines should be supplied with Ncm. CalibrationTechnical Specification•Maximum bending moment: 200 Kg.cm•Bending moment adjustable: 25- 200 Kg.cm•Range: (i) Kg.cm 25-125, (ii) Kg.cm 125-200•Gripping dia of specimen: 12 mm•Testing dia of specimen: 8 mm•Rotating speed: 4200 rpm•Acc of applied bending moment: ± 1%•Digital counter: 8 digits•Power required: 0.5 HP•Mains supply : 415 Volt, 50 Hz, 3 Phase A.C. Power Supply |
| 4 | PENDULUM IMPACT TESTING MACHINES WITH ACESSORIES, MILLING CUTTERS AND 10NOS OF STANDARD SAMPLES OF MILD STEEL,CAST IRON , ALUMINIUM AND BRASS FOR IZOD TESTING | Complying StandardsDesigned to carry out CHARPY AND IZOD Test as per IS: 1757-1961, IS: 1499- 1959, IS: 1598-1960, BS: 131: Part 1,2 & 3,Working PrincipleThe working of machine will be based on principle of potential energy that is measured by the difference of height of dropof swinging hammer before and after rupture of specimen.Features and Technical SpecificationsCapacity: 300 JoulesResolution: 2 JoulesAccuracy: Within 0.5 %Release of Pendulum by Hand operation.Safety guards for Protection.Assembly to hold standard Izod and Charpy Specimens.Braking Arrangement provided to arrest the swing of pendulum after specimen rupture.Standard size specimens of Izod Impact and Charpy 2 nos for each. |
| 5 | PORTABLE ROCKWELL HARDNESS TESTERS | •Impact device: D integrated•Hardness Scale: HLD, HB, HRC, HRB, HV, HS•Accuracy: ± 6 HLD (760 ± 30HLD)•Memory: 270 average readings in 9 group files•OUTPUT: RS 232 to printer•Min. Surface roughness of work: 1.6µm (Ra)•Max. work piece hardness: 900 HLD•Min. radius of work piece(convex/concave)Rmin =50mm (with support ring Rmin=10mm)•Min. work piece weight: 2~5kg on stable support: 0.05~2kg with compact coupling•Min. work piece thickness coupled: 5mm•Min. thickness of hardened layers: 0.8mm•Indentation depth: Impact devices data•Continuous Working Time: 150h (without backlight)•Power: AAA 1.5V batteries•Operating Temperature: 0~40 CFeature:USB communication interface,Automatic identification of Impact test direction,Memory of 270 average data in 9 group files,Upper and lower limit setting.Automatically switch offBack light for convenient use in darknessSoftware calibrationBattery capacity displayAAA 1.5V batteryIntegrated calibration functionTIME ®5100 : integrated with D impact device for normalhardness testing. |
| 6 | ERICHSEN CUPPING TESTING MACHINES | It Should be designed to:• Reveal the cupping qualities of metal sheets and strips.• Test the adhesion, elasticity & porosity of coats of paints or varnish by way of comparison. After Fracture, the material gives an indication of grain structure of the material and its constitution to some extent. The design parameters for the working and inspection methods of the machine are so selected, that the results are reliable.TECHNICAL DATA:Width of sample: 70 to 90 mm.Thickness of sample: 0.1 to 2 mmLeast count of micrometric device: 0.05 mmOne turn of hand wheel : 1.25 mm advance. |
| 7 | VICKERS CUM BRINELL HARDNESS TESTING MACHINES (ANALOG TYPE) | Suitable for finding out Vickers / Brinell hardness of metals fromsoft to very hard (Push button control for load selection).A rangeof test loads for Vickers / Brinell - from 1 kg to 250 kg.OpticalMagnifications - 35X, 70X & 140X .A precision Diamond Indentor(136° Pyramid) must be used to make sharp indentations on thespecimens / samples.Maximum Test height x Throat: 250 x 150 mm.Load accuracy well within ± 1% of nominal load value. |
| 8 | JOMINY END QUENCH HARDENABILITY SET UP | At a time 3 Jominy test must be carried outSpecial tong for quick transfer of specimen to quenching fixtureMotorized water tank with storage and test tank |
| 9 | MOHS SCALE | The Collection must contains 9 Minerals represents the scale of Hardness Talc (H=1), Gypsum (H=2), Calcite (H=3), Fluorite (H=4), Apatite (H=5), Orthoclase (H=6), Quartz (H=7), Topaz (H=8) &Corundum (H=9)Accessories & Tools: Knife, Iron Plate, Streak Plate, Glass Plate, Copper Plate, Iron Plate, Garnet Board, Magnet, Hand Lens, Acid Drop Bottle (Empty) & Instruction Manual for Doing These Test. |
| 10 | POLDI HARDNESS TESTER(REBOUND HARDNESS TESTER) | MATERIAL: Hardened steel ballDia: 10mm. Standard testy bar individually calibratedMeasuring range: 10mm. Scale graduation: 0.1mmMagnification: 10X accuracy of measuring 0.05mmHardness table: compression table for finding hardness separate tablefor steel, cast iron, brass, copper and aluminium |
| 11 | CARBURIZING BOX MATERIAL: CAST IRON SIZE: 4\"X4\"X6\" WITH LID | Made up of Cast iron with internal size of 4”x4”x 6”with cover and handle . Minimum wall thickness 12-16mm |
| 12 | K TYPE THERMOCOUPLE WITH TEMPERATURE INDICATOR | Technical Specification•Display: 3 1/2 Digital LCD•Cold Junction Compensation: Automatic Temperature compensation•Range: -50 °C to + 900 °C•Sensor Input : K - Type Thermocouple•Accuracy: 0.2 %•Probe length: 30 cm long•Operating Temperature: 0 - 50 °CSalient FeaturesPortable digital thermometer9 Volt battery operatedWith Fast Response Needle type 4mm dia immersion probe of about 7\"length.With test certificate, calibration certificate from NABL accredited lab warranty certificateDIGITAL THERMOMETER VARIETY: DTM 100 - 900°C CR/AL |
| 13 | PT-RH THERMOCOUPLE WITH TEMPERATURE INDICATOR | Technical Specification•Display: 3 1/2 Digital LCD•Cold Junction Compensation: Automatic Temperature compensation•Range: 600 °C to + 1300 °C•Sensor Input: R - Type Thermocouple ( Pt-Rh type)•Accuracy: 0.2 %•Probe length: 30 cm long•Operating Temperature: 0 - 50 °CSalient FeaturesPortable digital thermometer9 Volt battery operatedWith Fast Response Needle type 4mm dia immersion probe of about 7\"length.With test certificate, calibration certificate from NABL accredited lab warranty certificateDIGITAL THERMOMETER VARIETY: DTM 600 - 1300°C Pt-RH |
| 14 | INFRA RED THERMO METER | Infrared thermometer has an extremely wide temperature range which should allow you to carry out thermal measurements up to 1500 °C - and all from a safe distance. It doesn’t matter whether the objects are small, hard to reach, moving or very hot. temperature infrared thermometer allows you to measure the temperature in all four cases quickly and safely.- The 4-point laser clearly indicates the measuring area and prevents incorrect measurements- The 50:1 optics allow to carry out measurements from a long distance and still obtain excellent results(distance 5 m = 10 cm measuring spot)- The integrated degree of emission table should enable user to select the correct degree of emission of the measured surface- The backlit display should allow user to use infrared thermometer in all lighting conditionsIt should also allow user to carry out contact temperature measurements. The thermometer should be equipped with a connecting point for a wide range of optional temperature sensors. The temperature sensor can also be used to automatically measure the degree of emission of a particular surface. |
| 15 | BULK DENSITY CYLINDERICAL METAL MEASURE (ISI MARKED)-(30/15/3 LTRS) | Compliance with following International Standards : IS : 1199, IS : 10079, BS : 1881, ASTM C29, ASTM C138, EN 1097-3 Applications : For measurement of \"Unit weights\" and voids in aggregate. Apparatus Details : Made from thick gauge Mild steel Stout and rigid to retain form Water tight from top and bottom Smooth Interior wall Precision machined for true measurements Complete with handles for easy carriage Supplied Complete with tamping rod of 16mm diameter x 600 mm long. |
