Construction Of Quality Control Lab At Nohar Construction Of Quality Control Lab At Nohar
Tender Value
16.51 Lakhs
Estimated cost
Bid Submission
10 Jan 2022
0 days left
EMD
33020
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nohar → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Quality Control Lab At Nohar Construction Of Quality Control Lab At Nohar
BOQ
| Sl. No. | Item Description |
| 1 | PART-(A) MAIN BUILDING (CIVIL WORK) |
| 2 | Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. Add for additional lead upto 10 km. |
| 4 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 5 | Brick work with common burnt clay F.P.S. (Non Modular) bricks of class designation 7.5 infoundation and plinth withCement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 6 | Providing and laying in position specified grade ofcement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix |
| 7 | Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 8 | Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix |
| 9 | Half brick masonrywith common burnt clay F.P.S. (Non Modular) bricks of class designation 7.5 in foundation & plinth. Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 10 | Brick work with common burnt clay F.P.S.(Non Modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level in all shapes and sizes in: Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 11 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings,strap beam, raft , bases of columns etc. |
| 12 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. |
| 13 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. Thermo- mechnically treated bars (conf. To rel. IS Code) |
| 14 | Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applyinga coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-in-charge : |
| 15 | Providing and fixing external grade board solid core single/ Double leaf flush door shutters IS: 2202(Part-II)1996 marked using Phenol formal dehyderesinin glue both sides with approved stainless steel fittings complete as per annexure \"A\": |
| 16 | Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails completeas per approved by engineer in charge. 0.8mm thick mica |
| 17 | Providing and fixing fully panelled /partly panelleddouble leaf shutters frame for windows and ventilators as per approved design and drawings with approved steel fittings as per Annexure ‘A’ and width of styles, bottom and top rails 75mm including intermediate rails 50mm wide, beading of 25mm x 15mm size on both faces : 30 mm thick. Shesham wood grade I |
| 18 | Providing and fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutter 25 mm to 40 mm thick. 4 mm plain float glass |
| 19 | Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : |
| 20 | Kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand)For area of each slab from 2001 to 5000 Sq.Cm |
| 21 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirmingto IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 22 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 23 | P & F 1st quality Vitrifiedtiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade,laid with 20 mm thick CM 1 : 4 including grounting the joints with white cement and matching pigment etc complete.ize 600 mm X 600 mm |
| 24 | Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). |
| 25 | Painting top of roofs with bitumen of approved quality at 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete: With residual type petroleum bitumen of penetration 80/100 |
| 26 | Providing and laying Common burnt clay brick tiles of class designation 100 overroofs grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over a 12 mm layer of cement mortar 1:3 ( 1 cement : 3 fine sand ) and finished neat . |
| 27 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design. |
| 28 | Making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1:2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1:3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. |
| 29 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish: 20mm thick . |
| 30 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :12 mm thick. |
| 31 | Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. including scaffolding and safety provision OnNewwork |
| 32 | Providing and applying superior quality wall painting with Velvet touch emulsion paint of approved brand and manufacture to give an even shade with putty and preparation of surface applying with the help of paint roller the work complete in all respect as per direction of Engineer-in-charge.New Work Three or More coat |
| 33 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 34 | P&F rigid PVC Pipe (IS:4985 mark) class II (4 Kg /Cm2) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. |
| 35 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant:110mm dia |
| 36 | (A) Bend 87.5 |
| 37 | (B) Pipe clip |
| 38 | Computer Table(900x750mm) Providing and fixing of staff clerk room tablemade out of 18mm ply ISI BWP waterproof and acidproof and equalant make and 1mm thick mica at Top and inside, front having combination pattern the top thick 38mm and top edge teak wood biding decorative one sight box with drawer and shutter locking arrangement 1 Nos. key board tray or CPU arrangement with channel & self shutter complete melamine polish sample and color to be approved byEngineer-in-charge. |
| 39 | EXECUTIVE MEDIUM BACK REVOLVING OFFICE CHAIRProviding & Fixing of Executive medium back revolving chair having following specification : Seat/Back, Assembly: The seat/Back are made up of 12mm thick hot pressed plywood, upholstered with fabric and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra confort.Back Size :520mm (W) × 580mm (H)Seat Size :460mm (W) ×470nn (D)Overall Height : 1080mm Polyurethane Foam : The polyurethane foam is moulded with density = 45+2kg/m3Upholstery : Fabrick/Leatherette Arm rests: The one-piece of armrest in \"D\" shape made up of Polypropylene sample and color to be approved by Engineer-in-charge |
| 40 | WORKSTATION (COMPUTER) CHAIRProviding workstation revolving chair having following specifications : Seat/Back Assembly : The seat is made up of 12mm thick pressed plywood, upholstered with fabric and moulded polyurethane foam The back is made up of two piece injection moulded form. The inner frame is upholistered with mesh fabric and mounted on the main assembly. The back has adjustable lumber support for achieving comfortable seating posture.Back Size : 460mm (W)×580mm (H) Seat Size : 500mm (W)×480mm (D)overall height : 1010mm to 1110mm (H)Polyurethane Foam : The polyurethane foam is moulded with density = 48+/-2kg/m3.Upholstery : Fabric/mesh sample and color to be approved byEngineer-in-charges. |
| 41 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basicitem.) With float glass panes of 8 mm thickness |
| 42 | Providing steel pipe pedded chair includingtransporatation at site within Muncipal Limits, Loading, Unloading, Placing etc. complete. |
| 43 | PART-(B) MAIN BUILDING (SANITARY & WATER SUPPLY) |
| 44 | P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor |
| 45 | P & F water closet Seat Covers with brass hinges complete : Solid PVC (ISI marked) grade-I White for EWC. |
| 46 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 47 | P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor:Size 580x440mm. |
| 48 | P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete.WVC Flat Back half stall Urinal size 580x380x350 mm/ Angle back 450x375x350 type liped front.. |
| 49 | P & F W.V.C. Urinal Partition Plate of approved standard make of size 630x315mm including making good the wall. |
| 50 | P&FC.P.brassUrinalFlushPipeset complete with flanged brackets of approved make.For 3 Urinals |
| 51 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make,PVC waste pipe with PVC nut 32mm complete including cutting & making good the wall :Size 580 mm x 450 mm |
| 52 | Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.Size 600 x 450mm x 4 mm thick |
| 53 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms |
| 54 | P & F Grating of approved quality/make:Stainless Steel Grating100 mm Nominal dia |
| 55 | Providing & fixing C.P.flange for 15mm dia taps. |
| 56 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15 mm Brass (IS:8931 marked). |
| 57 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) |
| 58 | 20mm nominal outer dia pipes |
| 59 | 32mm nominal outer dia pipes |
| 60 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. (External work). 20mm nominal outer dia pipes |
| 61 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: C.P. Brass bib cock,15mm nominal |
| 62 | P & F 15 mm. Dia Connection Pipe of approved quality/make :PVC pipe withC.P. Brass nuts upto length, 450mm |
| 63 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : Gun-metal 15 mm. Nominal bore |
| 64 | P & F PVC Storage Tank (IS:12701 marked indicating the BIS license No.) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including placing on terrace (at all floors), making connection etc. complete of approved design. 1000 Litre capacity |
| 65 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single socketed pipes.Type B 75mm. dia. |
| 66 | Construction of manhole in all type of soil inner size 90 X 60 Cm. 230 mm thick brick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead.Depth up to 0.5 M |
| 67 | Construction of chamber in all type of soil with 230 mm thick brick masonry in CM 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 40mm thick M-15 grade C.C. flooring, earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr.do- size 450 x 450mm depth upto0.5 M,Cement concrete cover with frame. |
| 68 | Construction of septic Tank in all types of soil with 345 mm thick brick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C flooring & over stone slab covering ,80 mm thick slab ,jointing of slab in CM 1:3. Ralthal, Kharanja,50 mm thick stone partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos C.I foot rests of approved design, two No. 450 mm dia each cement concretecover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-Size 200 x100x130 cm.(for 10 users) |
| 69 | Construction of Soakage well in all types of soil of approved drawing, top 90 Cm .Portion in 450mm thick masonry with CM 1:6, 80 mm thick stone slab covering,jointing of slab in CM 1:3 ,Ralthal, kharanja 40mm thick M-15 grade C.C flooring, earth worketc . complete including disposal of surplus earth within a lead of 50 mtr . Inner dia90 Cm & 10 to 12 Mtr deep. |
| 70 | P & F Soap Dish or Tray of approved quality/make. C.P. brass |
AI Tender Summary
Tender Timeline
Dec 30, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedJan 10, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJan 12, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender