construction Of Inter Locking Tiles And Sdbc In Lane No 16 Near S.S.K Public School At Gandhi Colony 07
Tender Value
5.84 Lakhs
Estimated cost
Bid Submission
29 Dec 2021
0 days left
EMD
58000
Bank guarantee accepted
Document Fee
778
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Muzaffarnagar → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
construction Of Inter Locking Tiles And Sdbc In Lane No 16 Near S.S.K Public School At Gandhi Colony 07
BOQ
| Sl. No. | Item Description |
| 1 | Providing and applying Tack coat. 0.2 kg/sqm |
| 2 | Providing and laying bituminous concrete with 100-120 TPH batch type HMP prouducing an average ouput of 75 tonne per hour using crushed aggregates of specified grading premixed with Bituminous binder V-30@ 5.4% of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and alignment rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause No. 509 complete in all respects. |
| 3 | Providing and laying hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads@250gm per sqm area, thixkness of 2.5mm is exclusive of surface applied glass beads as per IRC:35-2015. The finished surface to be label,unifrim and free from streaks and holes. Rates are inclusive of all taxes royalty etc. all T&P machine material and labour required for propercompletion of work [Ch.27,SI.No. 7 new item / S.O.R-2020 |
| 4 | Reflective Raised Pavement marker with shanks of adequate length anchored with epoxy/bitumen adhesive of approved make(Cat Eye) Typex-ASTMD-4956-04 Avery Dennsion/3m(USA Make) having moulded body of polycarbonate, ASA, HIPS or ABS able to support a load of 13.635 M.T. tested in accordance withASTMD 4280 type H and other requirement mentioned in MORT&H Circular, its reflective lens made of micro prismatic lens (capable of providing total internal reflection of light), electronically welded to the body. The length, height and width of the body shall not exceed 130mm, 20mm and 105mm respectively, The area of each reflective surface shall not be less than 13 Sq cm. on eachside sloping at the angle of 35+5 degree to the base to ensure maxium refelectivly. it shall comply to specification of category A of MORT&H circular no. RW/NH 33023/10/97-DO-III dated 11.06.97 lenses shall be moulded of methyl methecrylate conforming to ASTMD 788 or equivment. With 7 yers warranty. Rate shall be inclusive of all taxes, royalty, etc, etc. All T&P/ machine material and labour requierd for proper completion of work.. S.I. No. Ch. No. 27/New item no. 11/ S.O.R-2020 |
| 5 | Cleaning of site during work, diversion of traffic, Photos of site. Etc. |
| 6 | dismentling old brick laid on edge kharanja including stacking of old brick. Chapter No20/New Item no.3/ S.O.R-2020 |
| 7 | Concrete with 4 cm gauge brick ballast, fine sand of 1.25 FM and cement in proportion of 12:6:1 in foundation and under floors including supply of all materials, labour, T&P etc. required for proper completion of the work.(SI No.273/2020 ) |
| 8 | Supply and Laying of 80mm thick ISI marked confirming to IS:15658-2006 I-shaped mechanically compressed COLOURED interlocking cement concrete paver blocks, smooth high gloss finish, skid resistant,manufactured from rubber moulds through vibro-compression mechanism, high pressure and control vibration machinehaving plan dimension 200x(160+120mm)with top layer of minimum 5mm thick topping of O.P.cement mixed with 25% marble powder . The compressive strength of concrete paver blocks shall not be less than 40Mpa and weight 4.5 kg per no. confirming to IS:15658-2006 including cost of all materials, labour, T&P etc., laying with a blanket layer of 4.00 cm thick fine sand including levelling and dressing surface up to required level and slope filling joints with fine sand including all required for proper completion of the work as directed by the Engineer-in- charge. |
AI Tender Summary
Tender Timeline
Dec 22, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedDec 29, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 30, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender