Construction Of District Secretariat At Lemmi In Pakke-Kessang District ( Sh- One Block Of 3200.00 Sqm ) ( Phase-I ) ., Pakke Kessang-Arunachal Pradesh

TDR : 30376074

Tender Notice
BOQ

Expired

Pakke Kessang , Arunachal Pradesh

Tender Brief : Construction Of District Secretariat At Lemmi In Pakke-Kessang District ( Sh- One Block Of 3200.00 Sqm ) ( Phase-I ) .

Document Fees
₹ 2000 /-

EMD
₹ 1225000.0 /-

Tender Value
₹ 12.25 Crore /-

Submission Date
05-01-2022

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	SH : I: EARTH WORK
2	Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sum on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing andramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.Ordinary Rock
3	Extra for every additional lift of 1.50 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil
4	Fillingavailableexcavatedearth(excludingrock)intrenches,plinth,sidesof foundationsetc.inlayersnotexceeding20cmindepth,consolidatingeach deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
5	Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth inlayersnotexceeding20cmintrenches,plinth,sidesoffoundationetc. complete.
6	Supplyingandfillinginplinthwith sandunderfloors,includingwatering, ramming, consolidating and dressing complete.
7	SH : II: PCC WORK
8	Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.
9	1:4:8 (1 cement : 4 coarse sand (Zone III) : 8 graded stone aggregate 40 mm nominal size).
10	SH : III : RCC WORK
11	Centering and shuttering including strutting, propping etc. and removalof form for :
12	a) Foundations, footings, bases of columns, etc. for mass concrete
13	Suspended floors, roofs, landings, balconies and accessplatform
14	b) Lintels, beams, plinth beams, girders, bressumers andcantilevers
15	c) Columns, Pillars, Piers, Abutments, Posts and Struts
16	d) Stairs, (excluding landings) except spiral-staircases
17	f) Extra for additional height in centering, shuttering where ever requiredwith adequate bracing, propping etc., including cost of de-shutteringand decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).
18	e) Suspended floors, roofs, landing, beams and balconies(Plan area to be measured)
19	Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering,finishingandreinforcement,includingadmixturesin recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.
20	a) All works upto plinth level : Concrete of M-25 grade Mix with minimum cement content of 330kg/cum
21	b) All works above plinth level upto floor V level : Concrete of M-25 grade Mix with minimum cement content of 330kg/cum
22	Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level.
23	Thermo Mechanically treated bars
24	Applying a coat of hot bitumen (mashphalte 80/100 or equivalent) using 1.70 Kg per Sq.m. on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil
25	SH : IV: BRICK WORK
26	BrickworkwithcommonburntclayF.P.S.(nonmodular)bricksofclass designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)
27	Half brick masonry in cement mortar 1:4 (1 cement :4 coarse sand) in foundation and plinth.
28	Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level.
29	Extra for providing and placing in position 2 Nos 6mm dia M.S. bars at every third course of half brick masonary.
30	SH:V :FLOORING WORK
31	Dry Stone Kharanja using stone as directed by Engineer In Charge using approved quality Stones
32	Providing and laying in foundations and plinth cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.
33	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete
34	c) Size of Tile 600x600 mm
35	Providing and laying Vitrified tiles in different sizes (thickness to bespecified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of eps,over 12mm thick bed of cemen tmortar1:3 (1cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete
36	c) Size of Tile 600x600 mm
37	Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete
38	Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
39	Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
40	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse and) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
41	SH : VI : FINISHING WORK
42	12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).
43	15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.
44	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
45	Granite of any colour and shade, Area of slab over 0.50 sqm
46	Providing and applying plaster of paris putty of 2 mm thickness overplastered surface to prepare the surface even and smooth complete.
47	Applying one coat of cement primer of approved brand and manufacture on wall surface.
48	Finishing walls with Premium Acrylic Smooth exterior paint withSilicone additives of required shade:
49	New work (Two or more coats applied @ 1.43 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm)
50	Providing and Fixing of Exterior Texture Paint, complete in all respect and in supervision of Engineer-in-charge
51	Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : 13.60.1 Two or more coats on new work
52	Painting two coats with oil wood preservatives of approved brand and manufacture on new work.
53	French spirit polishing (two or more coats) including a coat of wood filler on new work
54	Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.
55	Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate primimng coat, preparation of surface, etc, complete. On steel surface
56	SH : VII : WOOD/ ALUMINIUM WORK
57	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Kiln seasoned and chemically treated hollock wood
58	30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames.
59	30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.
60	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved makeconforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
61	a) For fixed portion
62	Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)
63	For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
64	Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)
65	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beading shall be paid in basic item)
66	With float glass panes of 5 mm thickness.
67	Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size).
68	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.9.48.2Fixed to openings /wooden frames with rawl plugs screws etc.
69	Providing and fixing aluminum butt hinges anodised, transparent or dyed to required color or shade with necessary screws etc complete.
70	a) 100 x 63 x 4 mm
71	Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessaryscrews etc complete.
72	a)250 x 10 mm
73	Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.
74	a)125 mm
75	Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete. a)300 x 16 mm
76	Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
77	Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws andPVC sleeves etc., wherever necessary complete :
78	9.46.325 mm dia
79	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
80	SH : VIII : SANITARY & PLUMBING WORK
81	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require
82	a) White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap
83	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required.
84	Kitchen sink without drain board
85	a) 610x510 mm bowl depth 200 mm
86	Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.
87	Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.
88	Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
89	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
90	Semi rigid pipe
91	a) 40 mm dia
92	Providing and fixing 100 mm sand cast Iron grating for gully trap.
93	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
94	Providing and fixing toilet paper holder :
95	a) C.P. brass
96	Providing and fixing soil, waste and vent pipes :
97	100 mm dia
98	Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989
99	75 mm diameter :
100	Centrifugally cast (spun) iron socketed pipe as per IS: 3989
101	Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :
102	75 mm diapipe
103	100 mm diapipe
104	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :
105	For 100 mm dia pipe
106	For 75 mm dia pipe
107	Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete
108	100 mm dia
109	Sand cast iron S&S as per IS - 3989
110	Providing and fixing heel rest sanitary bend
111	100 mm dia
112	Sand cast iron S&S as per IS - 3989
113	75 mm dia
114	Sand cast iron S&S as per IS - 3989
115	Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :
116	100 mm
117	75 mm
118	Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :
119	100mm
120	75mm
121	Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
122	100 mm inlet and 100 mm outlet
123	Sand cast iron S&S as per IS - 3989
124	Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :
125	100 mm dia
126	75 mm dia
127	Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete
128	Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
129	C.P.V.C. PIPES
130	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.
131	Internal work - Exposed on wall
132	a) 20 mm nominal outer dia Pipes
133	b) 25 mm nominal outer dia Pipes
134	c) 32 mm nominal outer dia Pipes
135	d) 40 mm nominal outer dia Pipes
136	e) 50 mm nominal outer dia Pipes (For Bottle Trap & O.H. Filling)
137	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge
138	Concealed work, including cutting chases and making good the walls etc.
139	a) 20 mm nominal outer dia Pipes
140	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.
141	External work
142	20 mm nominal outer dia Pipes
143	BRASS FITTINGS
144	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
145	20 mm dia nominal bore
146	25 mm dia nominal bore
147	Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main :
148	25 mm dia nominal bore
149	Providing and fixing uplasticised PVC connection pipe with brass unions :
150	30 cm length
151	15 mm nominal bore
152	45 cm length
153	15 mm nominal bore
154	C.P. BRASS FITTINGS
155	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
156	15 mm nominal bore
157	Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.
158	15 mm nominal bore
159	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.
160	15 mm nominal bore
161	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
162	15mm nominal bore
163	Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.
164	Cutting holes up to 30x30 cm in walls including making good the same:
165	With common burnt clay F.P.S. (non modular) bricks
166	Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.
167	Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.
168	Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) including disposal of malba.
169	DRAINAGE
170	STONE WARE PIPES AND FITTINGS
171	Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :
172	100 mm diameter pipe
173	150 mm diameter pipe
174	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :
175	100 mm diameter S.W. pipe
176	150 mm diameter S.W. pipe
177	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:
178	180x150 mm size P type
179	With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
180	Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :
181	Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
182	a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
183	Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) :
184	b) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
185	Extra for depth for manholes :
186	Size 90x80 cm
187	a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
188	Size 120x90 cm
189	b) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
190	Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :
191	a) With 20x20 mm square bar
192	Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg
193	Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :
194	a) For pipes 100 to 250 mm diameter
195	SH : IX : STRUCTURAL GLAZING
196	Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment
197	Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:
198	(a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:
199	(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.
200	(c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.
201	(d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.
202	(e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporatingprinciples of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.
203	Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places.
204	Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately.
205	The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or by any other accreditation body which operates in accordance with ISO / IEC 17011 and accredits labs as per ISO/ IEC 17025.
206	1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr
207	2. Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09 testing method for a range up to 2000 ml.
208	3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml
209	4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm
210	5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testing method for Qualitative test, Tests to be conducted on site.
211	6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml
212	Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor.
213	(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2)
214	For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.
215	(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.
216	Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin-Charge.
217	Providing and fixing of Dorma ES-200 frameless Automatic bi-parting sliding door operator for clear opening size of 2000 mm x2400mm, modular design, including internal cover, eagle sensors on bothsides,Electromechanical lock,light barriers and programme switch complete, With Operator Dimensions (LxH x T): 4150x100 x180 mm. The track profile should be separate from the main profile for enabling reduction in vibration. Microprocessorcontrol, self-learning, reversing whenobstruction is encountered. Microprocessorcontrolled control unit. It should be Selflearning, with adjustable parameters for opening and closing speed, hold-open timeand opening and closing force. Class of protection IP 20.,The glasses shall be of12mm clear toughend frameless with polished edges.
218	Item includes supply installation of toughened high performance glassof thickness 12mmasper ST - 467of Saint Gobain/ Modi/ Asahi Glass or equivalent ofincluding of sealants, brackets, fasteners, screws, sieve, backer rod, bolts, gasket, fixtures, etc. complete) The above work is to be carried out by associate Specialized Agency as per approval of the Engineer-in- Charge
219	SH : X : FALSE CEILING
220	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
221	12.5 mm thick tapered edge gypsum plain boardconforming to IS: 2095- (Part I) : 2011 (Board with BIScertification marks)
222	Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge.
223	With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)
224	SH : XII : FIRE FIGHTING
225	Fire Hydrant System
226	Supply, Installation, Testing & Commissioning of: Single headed, SS/ Gun Metal ISI marked oblique pattern hydrant landing valve with 80 mm dia flanged inlet and 63mm dia instantaneous type female outlet complete with Gun Metal cap and G.I. chain, twist release type plug and all accessories as per 13:5290-1983 (Type \"A\")
227	Supply, Installation, Testing & Commissioning of: First-Aid Fire Hose Reel wall mounting swinging type complete with drum, bracket, ball valve and 20mm dia.x 30M long high pressure Hose Reel tubing as per IS:444 with Gun Metal shut-off nozzle having 5mm dia. orifice. The Hose Reel shall strictly confirm to IS : 884-1985
228	Supply, Installation, Testing & Commissioning of: Non-percolatingflexible hose(RRL type-\"A\") ISI marked (IS:636) 63 mm dia x 15 M long complete with instantaneoustype SS/ Gun Metal 63mm dia. IS markedMale and female couplings (IS:903)bound and riveted to hose pipe with Gun Metal rivets and 1.5 mm Gun Metal wire
229	Supply, Installation, Testing & Commissioning of: SS/ Gun Metal 63mm dia short size branch pipes with 20 mm dia nozzle with 63mm instantaneous coupling ISI marked (IS: 903)
230	Providing & fixing standard fireman\"s axe with heavy insulated rubber handle.
231	Supply, Installation, Testing & Commissioning of:M.S. hose door fabricated from 16g M.S. sheet with full glass door and locking arrangement, suitable to accommodate 1 Hydrant landing valve, 1fire hose reel, 2 nos.15m long 63mmdia hose,1-branch pipe. The door shall be painted with one coat of primer and finished stove enamelled \"Fire Red\", \"Fire Hose\" written on front including suitably mounted on a raised masonry platform as required. (Approx. size 1.2m x .6m x2.1m )
232	Supply, Installation, Testing & Commissioning of Gun Metal Fire Brigade connection (Suction collecting head) consistingof63 mm dia instantaneous type male coupling with built-in check valves and 150 mm dia. flanged outlet complete with bolts, nuts and rubber insertions as requiredas perIS:904-1983
233	Supply, Installation, Testing & Commissioning of: M.S. cabinet (toenclose above. Draw-out/Fire brigade inlet connections)fabricated from 16 g sheet with full front glassdoor and locking arrangement duly painted with one coatof primer and twoormore coats of synthetic enamel paintofapprovedmake andshadeandsuitably mounted on a raised masonryplatformas required(Approx.0.6 m x 0.6 M x 0.45 M ).
234	Supply, Installation, Testing & Commissioning of: Aircushiontank(air-vessel) 250 mm dia. x 1.0 Mhigh with dishedtop, madeofminimum6 mm thick M.S. pipe/plate complete with 25mm dia. BrassAirValve (Ball valve, pressure gauge type),25 mmdia.Stop withbrassstop cock, nipple,tees, elbow, pipe and allaccessories as requiredincl. fixing brackets.
235	SUPPLY, INSTALLATION, TESTING & COMMISSIONING of Mild Steel pipe (IS:1239 Part-I) heavy class including cutting, threading, welding etc. bends, elbows reducers, clamps, hangers etc.including cutting holes in brick or RCC walls/slabs and making good the same complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including all steel work.
236	a) 200 mm diaIS 1239
237	b) 150 mm diaIS 1239
238	c) 100 mm diaIS 1239
239	d) 80 mm diaIS 1239
240	e) 50 mm diaIS 1239
241	f) 25 mm diaIS 1239
242	Supply, Installation,Testing & Commissioning of: MildSteelblack pipe (IS:1239 Part-1) heavy class including cutting, screwing, welding etc.complete with fitting viz. tees elbow, bends, flanges, reducers.etc including providing anti-corrosive treatment (coating & wrapping) with 4mm thick tape and holiday test check as per IS: 10221complete as required including necessary excavation, refilling etc. complete.
243	a) 150 mm dia
244	b) 100 mm dia
245	Supply, Installation, Testing & Commissioning ofslim seal dual type non-returnvalves (PN 1.6) complete withmatching flanges, rubberinsertion,nuts, bolts and washer etc. of following sizes.
246	a) 150 mm dia
247	Providing and fixing Slim seal Butterfly valves (PN 1.6) completewith matching flanges rubber insertion, nuts. bolts andwasher etc. of following sizes
248	a) 150 mm dia nominal bore
249	AUTOMATIC SPRINKLER SYSTEM
250	SUPPLY, INSTALLATION, TESTING. & COMMISSIONING OF:
251	ElectricalMotorDriven Fire Pumping set suitable forautomatic operation consisting ofthe following as per the specifications.
252	a) Horizontally mounted, centrifugal type single stage firepump having cast iron body, bronze impeller, stainless steel shaft& capable of delivering 1620 LPM against atotal head of 60 M complete with all accessories pressure gaugeetc. as requiredAs per approved make
253	b) Squirrel cage induction motor totally enclosed fan cooled 2900 RPM type suitable for 415 Volts+ 10% - 15% , 3 phase, 50 HZ A.C. supply of suitable capacity forthe above pump coupled with flexible coupling includingearthling as per relevant Indian Standard & specifications.
254	c) Common bed plate for mounting Pump and Motor fabricated of suitable M.S.Channel asper manufacturer\"s recommendations.
255	d) Suitable RC.C Pump-Foundations as per manufacturer\"s design and 4 nos.Dunlop (cushy foot) heavy duty Anti vibration mounting pads.
256	Diesel Engine Driven Fire Pumping set suitable for automatic operation consisting of the following as per specifications
257	a) Horizontally mounted, centrifugal type single stage/ multi-stage fire pump having cast iron body, bronze impeller,stainless steelshaft & capableof delivering 1620 lpm against a total headof60 m completewith all accessories pressure gaugeetc. as requiredAs per approved make
258	b) Water cooled TAC approvedDiesel Engine suitable for developing required BHP at 1800 RPM) for above pump complete with automatic starting mechanism, batteries, automatic battery charger unit, flexible coupling with the pump, coupling with the pump, fuel tank, silencer, exhaust pipe & allstandard accessories as required as per TAC rules including earthing, mandatory spares and tool kit.
259	c) Common bed plate for mounting Pump and Engine fabricated of suitable M.S.Channel as per manufacturer\"s recommendations.
260	d) Suitable RCC Pump foundations as per manufacturer \" s design 8 Nos Dunlop Anti-vibration (cushy foot) heavy duty mounting pads.
261	SUPPLY, INSTALLATION TESTING &COMMISSIONING OF:
262	a) Electrical Motor Driven Automatic pressurisation (Jockey) pumping set consisting of the following as per specifications. Horizontally mounted centrifugal type single/multi-stage fire pump for building pressure loss due to any leakage in the system and capable to deliver approx 180 LPM against a total head of 60 M with all accessories pressure gaugeetc. as requiredAs per approved make
263	b) Squirrel cage induction motor totally enclosed fan cooled type at 2900 RPM suitable for415 Volts + 10% - 15%3 phase. 50 HZA.C. supply of suitable capacity for the above pumpwith synchronous speed of 1500/3000RPM confirming to IS: 325 & duly coupledwith abovepumpcoupled with flexible coupling including earthling as per relevant Indian Standard and specifications.
264	c) Common bed plate for mounting Pump and Motor fabricated of suitable M.S.Channel as per manufacturer\"s recommendations.
265	d) Suitable RCC Pump foundations as per manufacturer\"s design 4 Nos Dunlop Anti-vibration (cushy foot) heavy duty mounting pads.
266	Supply,Installation,Testing & Commissioning of fire pump on terrace as per specification horizontally mounted centrifugal type for building and capable to deliver approax 450 LPM againsta total head of 35M having cast iron body.Bronze impeller, stainless steel shaft and complete with \"Y\" strainer on the suction side,butterfly valve on suction and delivery side,non return valve on delivery side and Pressure Gauge with stop G.M. Stop Valve etc. for periodical testing of the working of the pumping set and Suitable RCC Pump foundations as per manufacturer\"s design 4 Nos Dunlop Anti-vibration (cushy foot) heavy duty mounting pads including all kinds of accessories & valves required for terrace pump installation complete in all respect.
267	Supply, Installation, Testing & Commissioning of cubical typewall mounted Fire Pump Control Panel (For Terrace Pump at Roof) with One FullyAutomatic DOL Starter suitable for 450 LPM Pump Motor with over loadrelay, timer push buttons and Auto/Manual selector switch.
268	Supply, Installation, Testing & Commissioning of cubical typefloor mounted Fire Pump Control Panel (For Fire Pump Room) fabricated from14 g M.S. CRCA Sheet duly powder coated finish of approvedshade and comprising of :
269	INCOMING:
270	One 125 amp. TP + NL M.C.C.B. with rotary handle of breaking capacity 25KA
271	One- digital Volt Meter (0-500 V) with selector switch
272	One Set indicating lamps (LED)
273	BUS BARS OUTGOING:
274	125 Amp TPN BUS BAR (Aluminum).
275	One - 100 Amp. TP + NL M.C.C.B. with rotary handle of breaking capacity 25KA
276	One - 40 Amp.TP + NL M.C.B. with breaking capacity 10KA
277	One - 20 Amp.DP M.C.B. with breaking capacity 10KA
278	Two Fully Automatatic Star-Delta starters suitable for two electric & jockey Pump Motor with over load relay timer push buttons and Auto/Manual selector switch
279	Four panel type Amp. meters onefor each motor with ASS. CTS etc.
280	Four sets of On/Off - LED indicating lamp.
281	Fully Automatic Diesel engine starting system complete with battery charger, 4 window annunciator, indicating lights, transformer, rectifier, timer, voltmeter ammeter, selector switches, push buttons, auxiliary relay etc. complete as required as per fire authority.
282	All interconnecting power & control wires/cables suitable size within the panel and from panel to motors diesel engine, pressure switches, level switches, cable Tray, pipes etc. including brass glands termination within fire pump house and earthing as per specifications (Power cable size shall not be less than 1Nos. 3.5 x 95 mm sq., (3.5 x 50 Sqmm) for main pumps motor and 1 No. 4x16 mm sq for jockey pump motor.
283	Slim seal dual plate type non-return valves (PN 1.6) complete with matching flanges, rubber insertion, nuts, bolts and washer etc. of following sizes.
284	150 mm dia
285	100 mm dia
286	80 mm dia
287	Slim seal Butterfly valves B 190 Class (PN1.6) complete with matching flanges rubber insertion, nuts. bolts and washer etc. of following sizes :
288	80 mm dia
289	100 mm dia
290	150 mm dia
291	200 mm dia
292	Providing and fixing Ball valve with hard chrome plated ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete: in all respects.
293	50 mm dia nominal bore
294	Supply, fixing, testing and commissioning in position the following Y - STRAINER in Pump SuctionWater line complete with flanges etc as per specifications & drawings.
295	150 mm dia MS pipes
296	100 mm dia MS pipes
297	Providing and fixing resilient rubber neoprene lined single arch vibration eliminators suitable for raw water up to 450C temperature working pressure 7kg and test pressure 14 kg/ cm2.
298	80 mm dia
299	100 mm dia
300	150 mm dia
301	Day Oil Tank (Rectangular)
302	Double shell M.S. fabricated of IS:226 plate of 200 liters Capacity x 8mm thick. With inlet & outlet nozzles, Control Valve, Float Valve, Pipes, Flanges, Gaskets, bolts, nuts & internal supports.(The outer shall be having 110% capacity of the inner shell)
303	Electrical Fault-isolation Modules to protect the system against wire to wire short circuits on loops, to be installed at the rate of every 3 nos. monitor modules complete as per manufacturer specifications and in an accessible location as per site, excluding wiring to Annunciation Panel, with UL/FM approval.
304	Automatic electrically operated hooter ofrequired db (min.40) capacity fire alarm, to be connected to the main fire panel and zonal sprinkler annunciation panel, complete in all respects as per requirements.
305	a) For main fire panel at the main fire pump starter
306	b) For sprinklers zonal panel at main sprinkler pump starter
307	PORTABLE CHEMICAL FIRE EXTINGUISHERS
308	Supply and fixing of ISI marked( IS : 15683 ) ABC (Dry Powder) fire extinguishers cap 10 kg (9Kg) in seamless HP steel cylinders ISI marked and approved by CCE Nagpur fitted with pressure indicating gauge, internal tube squeeze level type valves fully charged with ABC powder and pressurized by Nitrogen complete in all respects including wall suspension bracket.
309	Supply and fixing of ISI marked (IS:2878) Portable fire Extinguisher, Carbon-dioxidetype flat base including valve, dischargehose of not less than 10 mm dia. 1m long& completeinall respectsincluding initial fill with CO2 gas conforming to IS:307-1966 filled to a filling ratio ofnot morethan0.667andwallsuspension bracket.
310	Capacity 4.5 Kg
311	SH:XI :HVAC WORK
312	HVAC SYSTEM SUPPLY:
313	AIR COOLED DX SYSTEM :
314	Supply and installation of copper refrigerant piping of requiredsizes duly insulated with closed cell elastomeric insulation thickness as specified by manufacturer,as per pipe size and cabling between indoor and outdoor complete with proper supports etc for following capacity unit. All related civil work such as making hole, chasing in wall, shall be inclusive in the quoted price.
315	a) GROUND FLOOR
316	1.0 TR WALL MOUNTED UNIT
317	1.5 TR WALL MOUNTED UNIT
318	2.0 TR WALL MOUNTED UNIT
319	2.5 TR WALL MOUNTED UNIT
320	b) FIRST FLOOR
321	1.0 TR WALL MOUNTED UNIT
322	1.5 TR WALL MOUNTED UNIT
323	2.0 TR WALL MOUNTED UNIT
324	2.5 TR WALL MOUNTED UNIT
325	c) SECOND FLOOR
326	1.0 TR WALL MOUNTED UNIT
327	1.5 TR WALL MOUNTED UNIT
328	2.0 TR WALL MOUNTED UNIT
329	To supply, install, test and commission UPVC drain pipes duly insulated with 6 mm thick nitrile rubber and \"U \" traps from indoor units to nearest drain point.
330	25 mm dia.
331	50 mm dia.
332	AIR DISTRIBUTION
333	Supplying, installing, testing and commissing of direct driven PROPELLER FANS for exhaust air as shown in drawings. Each fan shall be complete with permanent split capacitor or shaded pole motor, mounting plate, accessories like guard, bird-screen & fixed louvers for weather protection as required. Fan selection arrangement and electrical characteristics shall be as follows.
334	230 mm dia 1400 RPM fan suitable for 220 +(-)6% volts 50 cycles, 1 Phase AC supply
335	300 mm dia 1400 RPM fan suitable for 220 +(-)6% volts 50 cycles, 1 Phase AC supply
336	450 mm dia 1400 RPM fan suitable for 220 +(-)6% volts 50 cycles, 1 Phase AC supply
337	AIR DISTRIBUTION SYSTEM
338	DUCT
339	Supply, fabrication, installation, and testing of site Fabricated ducts of following thickness including necessary supports flexible hangers with isolators, nut bolts, gasket, splitter damper,duct dampers, vanes, etc. complete as per specifications in accordance with the approved shop drawings.
340	SITE FABRICATED DUCT
341	24 gauge galvanised sheet (0.63 mm)
342	GRILLE / DIFFUSER
343	Supply, installation, testing and commissioning of terminal air distribution equipment as per approved shop drawings, colour and specifications.
344	Aluminium powder coated air grille with damper for exhaust of 150 x 150mm
345	SH : XII: PASSANGER ELEVATOR
346	Providing & Fixing Passanger elevator as per specifications
347	for thyssenkrupp Elevator (India) Pvt. Ltd.
348	SH : XIII: ELECTRICAL & COMMUNICATION WORK
349	CHAPTER-1 - W I R I N G
350	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
351	Group B
352	Wiringfortwincontrollightpointwith1.5sq.mmFRLSPVC insulated copper conductor single core cable in surface / recessedmediumclassPVCconduit,2waymodularswitch, modular plate, suitable GI boxand earthing the point with 1.5 sq.mmFRLSPVCinsulatedcopperconductorsinglecorecable etc. as required.
353	Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium classPVC conduit alongwith1No.4sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
354	Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
355	Wiring for circuit/ submain wiring alongwith earth wire with the followingsizesofFRLSPVCinsulatedcopperconductor,single corecableinsurface/recessedmediumclassPVCconduitas required.
356	2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
357	2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
358	2 X 4 sq. mm + 1 X 4 sq. mm earth wire
359	2 X 6 sq. mm + 1 X 6 sq. mm earth wire
360	2 X 10 sq. mm + 1 X 6 sq. mm earth wire
361	4 X 10 sq. mm + 2 X 6 sq. mm earth wire
362	Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.
363	2 Pair
364	Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
365	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
366	20 mm
367	25 mm
368	32 mm
369	40 mm
370	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
371	Telephone socket outlet
372	TV antenna socket outlet
373	Bell push
374	Supplying and fixingtwo module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
375	Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
376	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.
377	1 or 2 Module (75mmX75mm)
378	3 Module (100mmX75mm)
379	4 Module (125mmX75mm)
380	6 Module (200mmX75mm)
381	8 Module (125mmX125mm)
382	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
383	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required
384	Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
385	Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connectionsetc. as required.
386	Supplyingandfixingcallbell/buzzersuitableforsinglephase,230 V, complete as required.
387	Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
388	Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.
389	Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.
390	Upto 450 mm sweep
391	Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
392	Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
393	1 run of cable
394	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductorsinglecorecableinsurface/recessedPVCconduit, andearthingthepointwith1.5sq.mmFRLSPVCinsulated copper conductor single core cable etc. as required.
395	Group B
396	Supplying and fixing PVC batten/ angle holder including connections etc. as required.
397	CHAPTER-2-MCCB, MCB & DB’S
398	Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
399	12 way , Double door
400	Supplyingandfixingfollowingway,horizontaltypethreepole andneutral,sheetsteel,MCBdistributionboard,415V,on surface/recess,completewithtinnedcopperbusbar,neutralsurface/recess,completewithtinnedcopperbusbar,neutral includingearthingetc.asrequired.(Butwithout MCB/RCCB/Isolator)
401	a) 4 way (4 + 12), Double door
402	b) 6 way (4 + 18), Double door
403	c) 8 way (4 + 24), Double door
404	Supplyingandfixing5Ato32A rating, 240/415V, 10kA,\"C\" curve,miniaturecircuitbreakersuitableforinductiveloadof followingpolesintheexistingMCB DBcompletewith connections, testing and commissioning etc. as required.
405	a) Single pole
406	b) Double pole
407	c) Triple pole and neutral
408	Supplyingandfixingsinglepoleblankingplateintheexisting MCB DB complete etc. as required.
409	Supplying and fixing following rating, double pole, (single phase andneutral),240V,residualcurrentcircuitbreaker(RCCB),havingasensitivitycurrent30mAintheexistingMCBDBcompletewithconnections,testingandcommissioningetc.as required.
410	a) 25 A
411	b) 40 A
412	Providing and fixing M.V. danger notice plate of 200 mm X 150mm,madeofmildsteel,atleast2mmthick,andvitreous enameled white on both sides, and with inscription in single red colour on front side as required.
413	Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete withtesting and commissioning etc.as required.
414	a) For 4 way, Double door TPN MCB DB
415	b) For 6 way, Double door TPN MCB DB
416	c) For 8 way, Double door TPN MCB DB
417	CHAPTER-4-CABLE TRAYS
418	Hot Dipped Galvanized Iron Cable Tray
419	Supplying and installing following size of perforatedHot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.
420	300 mm width X 50 mm depth X 1.6 mm thickness
421	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray \"bends\" (galvanisation not lessthan 50microns)withperforation notmore than 17.5%, in convenientsections,joinedwithconnectors,suspendedfrom the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.
422	300 mm width X 50 mm depth X 1.6 mm thickness
423	Supplying and installing following size of perforated Hot Dipped GalvanisedIroncable tray \"Tee\" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections,joinedwithconnectors,suspendedfromtheceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.
424	300 mm width X 50 mm depth X 1.6 mm thickness
425	CHAPTER - 5 - E A R T H I N G
426	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick includingaccessories,andprovidingmasonryenclosurewith coverplatehavinglockingarrangementandwateringpipeof 2.7 metre long etc. with charcoal/ coke and salt as required.
427	Earthingwithcopperearthplate600mmX600mmX3mm thickincludingaccessories,andprovidingmasonryenclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
428	Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipefromearthelectrodeincludingconnectionwithbrassnut,bolt, spring, washer excavation and re-filling etc. as required.
429	Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipefromearthelectrodeincludingconnectionwithG.I.nut, bolt, spring, washer excavation and re-filling etc. as required.
430	Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
431	Providingandfixing25mmX5mmG.I.striponsurfaceorin recess for connections etc. as required.
432	Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
433	CHAPTER 6 - LIGHTNING CONDUCTOR
434	Providingandfixingoflightningconductorfinial,madeof25 mm dia 300 mm long, G.I. tube, having single prong at top, with85mmdia6mmthickG.I.baseplateincludingholesetc.complete as required.
435	Fixing of lightning conductor finial (single prong) with base plateincluding holes etc. complete as required.
436	Jointing copper / G.I. tape (with another copper/ G I tape, baseofthefinialoranyothermetallicobject)byriveting/nutbolting/ sweating and soldering etc as required.
437	Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightningconductor completeas required.(For horizontal run)
438	Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet orsurface of wall for lightning conductor complete as required.(For vertical run)
439	Providing and fixing testing joint, made of 20 mm X 3 mm thickG.I.strip,125mmlong,with4nos.ofG.I.bolts,nuts,chuck nuts and spring washers etc. complete as required.
440	ProvidingandlayingG.I.tape32mmX6mmfromearth electrode directly in ground as required.
441	CHAPTER 7 - MV CABLE LAYING
442	Laying ofone numberPVC insulated and PVC sheathed/ XLPE powercableof1.1KVgradeoffollowingsizeintheexisting RCC/ HUME/ METAL pipe as required.
443	a) Upto 35 sq. mm
444	b) Above 35 sq. mm and upto 95 sq. mm
445	c) Above 95 sq. mm and upto 185 sq. mm
446	CHAPTER 8-HT CABLE LAYING
447	Laying of one number PVC insulated and PVC sheathed / XLPEpower cable of 11 KV grade of following size direct in groundincluding excavation, sand cushioning, protective covering andrefilling the trench etc as required.
448	Upto 120 sq. mm
449	CHAPTER 9-MV CABLE JOINTING & END TERMINATION
450	Supplying and making end termination with brass compression glandandaluminiumlugsforfollowingsizeofPVCinsulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
451	a) 3½ X 35 sq. mm (32mm)
452	b) 3½ X 50 sq. mm (35mm)
453	c) 3½ X 70 sq. mm (38mm)
454	d) 3½ X 185 sq. mm (57mm)
455	CHAPTER-10- FIRE DETECTION AND ALARM SYSTEM
456	INTELLIGENT FIRE ALARM SYSTEM
457	Supplying,installation,testingandcommissioningofmicro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (includingdetectors)andminimum120detectorsperloop andlooplengthupto2km,networkcommunicationcard, minimum320charactergraphics/LCDdisplaywithtouch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuationsystem(whichispartofthescheduleofwork under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications.
458	a) Two Loop Panel.
459	Supplying, installation, testing & commissioningof intelligent analogaddressablephotothermaldetectorcompletewith mounting base complete as required.
460	Supplying, installation, testing & commissioning of fault isolator complete with base as required.
461	Supplying, installation, testing & commissioningof addressable manual call point complete as required.
462	Supplying, installation, testing & commissioningof addressable horn cum strobe complete as required.
463	PUBLIC ADDRESS SYSTEM
464	Supplying,installation,testing&commissioningof6zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.
465	Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.
466	Supplying,installation,testing&commissioningofdigital audioamplifier75Watt,25Vrmsoperatingat240VoltAC Supply complete as required.
467	Supplying, installation, testing & commissioning of Voice commandkeypad6zone,withmicrophoneassembly complete as required.
468	CABLING & WIRING
469	Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000Vratedwithannealedcopperconductorhaving XLPEinsulation,steelwirearmouring&FRLSoutersheath complete as required.
470	speaker cable Single pair, 2-core, 1.5 sqmm
471	NON DSR ITEMS
472	Fixture
473	Supply of below mentioned Items-
474	a) 36Watt Square LED Natural Light
475	b) 12 Watt LED Light
476	c) 1200 MM Ceiling Fan
477	d) 225mm Exaust fan
478	e) Data Socket(RJ-45 CAT6) (Legrand Myrius)
479	Make:
480	Light- Philips
481	Fan -Havells
482	Supply of HT/ LTCABLES
483	Supply offollowing 1100 voltgradeXLPE insulated PVC inner sheathed and FR PVC outer sheathed Aluminium conductor armoured LT cables .(Make: Cable- GuptaPower, Polycab, RR Kabel, Havells )
484	3.1/2 core 185 sq. mm.
485	3.1/2 core 70 sq.mm
486	3.1/2 core 50 sq.mm
487	3.1/2 core 35 sq. mm
488	Supply of LTPANEL
489	(Make: L & T)
490	MAIN LT PANEL with AMF
491	INCOMER
492	400A, FP, MCCB ,36 KA (2 Nos.)
493	METERING & INDICATION with each incomer
494	-ON/OFF phase indicating lamps with control fuses .
495	- Multifunction Meter with CT\"s
496	BUS BAR
497	\"800 A, TPN, Al Bus Bars with heat shrinkable PVC Sleeves
498	OUTGOINGS
499	100 A, FP, MCCB, 16 Ka – 12 Nos
500	63 A, FP, MCCB, 16 Ka – 2 Nos

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Arunachal Pradesh Tenders

Construction Tenders

Civil Construction Tenders

Civil Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Construction Of District Secretariat At Lemmi In Pakke-Kessang District ( Sh- One Block Of 3200.00 Sqm ) ( Phase-I ) ., Pakke Kessang-Arunachal Pradesh

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Construction Of District Secretariat At Lemmi In Pakke-Kessang District ( Sh- One Block Of 3200.00 Sqm ) ( Phase-I ) ., Pakke Kessang-Arunachal Pradesh

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us