Bids Are Invited For Tool Bits 12 X150mm Sq. Assorted Shaped - Basic Diagram Attached, Compliance: Confirmiming To Is:11143-1991, Length `L`:150Mm ( +Or-1.5Mm ) , Width `W` :12Mm, Material:Hss-T42 / S400, Finish:Milled / Ground, Hardness: 65-69 Hrc, Surface Treatment:Bright Finish. , Laboratory Type Induction Coil1000 W - Basic Inductive Diagram Attached, Spark Length-10Mm-75Mm ( Adjustable ) , Product Type:Corrugated Box, Spark Length Are Workable-4-6 Volts And Rest On 6-12Volts Dc, Cabinet Opolish Wooden Box, Coils Are Made From Best Quality Copper Wire And Parafin Insuletion Is Provided Thorughout, Fitted With Platinum Contact With Removable Spasrk Discharger, Complete With On / Off Switch Of Primasry And Two Backetlite Look Type Terminals. , Tool Bit Assorted Sizes On Holder - Hss Tool Bit - 10Mm X 10Mm X 150Mm S 500 Grade, Hss Tool Bit - 16Mm X 16Mm X 150Mm S 500 Grade, Hss Tool Bit - 6Mm X 6Mm X 150Mm S 500 Grade, Basic Diagram Attached, Compliance: Confirmiming To Is:11143-1991, Length `L`:150Mm ( +Or-1.5Mm ) , Width `W` : 10Mm, 16Mm, 6Mm Material:Hss-T42 / S400, Finish:Milled / Ground, Hardness: 65-69 Hrc, Surface Treatment:Bright Finish. , Revolving Center ( To Suit Lathe Tailstock ) Mt-3 - As Per Lathe Tailstock Size Of Revolving Center Is Mt- 2 To Mt -5 , Ear Plug - Headset With Noise:Cancelling Boomk Microphone 3.5 Mm Analog Stereo, Pc / Mac / Laptop-Black, Headphone Type-On The Ear, Headphone Design-Over The Head, Connectvity-Wired, Microphone-Yes, Warranty-1Year, Noise Cancelling Mike, Adjustable Holder. , Radious Turning Attatchment ( For Surface Grinding Machine ) - Basic Indicative Diagram Attatched, Center Height :65Mm, Dressing Grinding Wheel Diameter : Dia 205Mm, Dressing Arc Min Size : Dia 0.5Mm, Convex R Trim Range 0-12Mm, Concave R Rim Range : 0-25.4 Mm, Skateboard Finished Stroke 22.5Mm, Trim Angle : 95 Degree - 0 Degree -95Degree, Throught Hole Diameter: Dia 30Mm, Size: 230 X 75 X 97Mm, Body Material Grey Cast Iron. , Lathe Mandrels ( Different Types ) - Different Types , Grinding Wheel Dressor Diamond Type - Sku: Too.Dia.18124303, Type Of Product: Single Point Diamond Dresser, Tip Material: Raw Diamond 1Mm To 4Mm, Sub Type: Regular Size: 0.75 Or 1 Carat, Carat Shank Size: 12.5 X 135 Mm, Material: Carbon Steel Knurling Handle , Drill Chuck 12Mm Cap. With Key - Basic Indicative Diagram Attatched, Total Length:204Mm +2Mm & -2Mm, Maximum Diameter:52Mm +1Mm & -1Mm, Shank:Mt-3, Capascity:5Mm To 20Mm, Key Operated Guided Jaws Type, Material:Carbon Steel, Screw Rings Should Be Hasrdned And Ground, Key Should Be Hardened And Blacked. , Tool Maker`S Button - Toolmakers Buttons Are A Set Of Small Tubes About 15Mm Od And 15Mm Long, They Have Holes In Them That Are About 10Mm In Diameter, These Tubes Are Hardened & Ground So That The Outside Diameters Are All Exactly The Same Nominal Size & The Ends Are At Right Angles To The Sides, Material Harden Steel , Tool Cemented Carbide Assorted Shaped External - Basic Diagram Attached, Compliance: 163 Stright Turning & Groovingsize : 16X16 Mm Overall Length : 110Mm Insert Grade P40 , Spare Grinding Wheel Ajax Type For Carbide Tool - Color :- Green 90.2 Material Type :- Silicon Carbide , Size – 150X25x20 Mm &300X40x30 Mm 90.3 Grit :- Aa120 , Marking Table ( C I ) 120 X 120 Cm - Material:-Cast Iron, Size:-120 X 120Cm, Height With Table:-150Cm, Material:Special Cast Iron With Steel Alloy, Wear Resistant Surface, Surface Machined To Din 876 / Iii Or Din 876 / 11, 4 Sides Square To The Plate Surface, Exactly Adjustable Through Different Kinds Of Supports, Prepared For The Installation On Supports Vs / Vsk. , Combination Drill / Center Drill A3, A 4, & A 6 - Hss Center Drill Type A Is 6708-1977 Din:333 Refer Tender Documents For Detail Specification , Grinding Wheel Dressor Huntington Type - Diameter:-1`` To 2 / 3``, Thickness 3 / 32`` To 1 / 8``, Cutting Face 1 / 2`` To 1.75``, Cutter Set 4 Cutter-2 Spacers, 12 Cutter-4 Spacers , Grinding Helmet - Basicinductive Diagram Attatched, Viewing Area:-90 X 40Mm, Ultgra Violet / Infra Red Protection, Best Quality , As Well As Fine One That Ears Confortably All Day On The Job. , Drill Drift - Finish Black Oxide Material High Carbon Steel, Fits Morse Taper Sockets / Sleeves L1 = 150 Mm L3 = 25Mm B = 20Mm, S = 5Mmmaterial Quality Too Steel , Wheatstone Bridge With Galvonometer And Barttery - Basic Indective Diagram Attached Broad Heavily Plated Brass Strips Should Be Mounted On Polished Harwood Base, Terminals With 4Mm Sockets Shold Be Provided, 24 Swg Constantan Wire Should Be Stretched Along The Top Of A Meter Scale In Mm And Cm, Should Be Supplied With Jockey, Dimensions: 1.13Mm X 80Mm X 50Mm ( Approx ) , Two Gap , Center Drill A-1 To 5 - Basic Indective Diagram Attached Type : Pilto Type Drills Usage / Application : Drilling Center Holls Material Grade : M2, M35, & M42 Size : 4Mm Length : Various Material : Hss Brand , Bit Dymeter Center Drill Bit Dymeter: Variousshank Type Straight Tool Flute Length : Various Hardness : Hrc , Welding Booths 4 X 5 Feet Including Job Holder - Welding Booths 4 X 5 Feet Including Job Holder , Vice Mounted Table 3.5` X 2.5` Ft - Basic Inductive Diagram Attatched Total Length:-3.5 Ft, Total Width:-2.5 Ft, Height:-2.5 Ft, Material:-M.S.Square Pipe 50Mm X 50Mm X 05Mm, Quality Ms Plate Top 05Mm Thick, Powder Coated Frame, Properly Welded.Colour : Mantle Gray Total Quantity : 1
