|
| 1 | Wooden Mallet | Dimensions I. Total Length: 325 mm ± 3mm II. Max. Width.: 128 ± 1mm III. Min. Width: 112 ± 1mm IV. Thickness: 60 mm ± 1mmWood material: Hard WoodHandle grip is secured by a long taperShould be light weight for fine workingFinishing = Fine finishing with body or chamfered. Should easy to operate for operator during hammering. |
| 2 | scraper Traingular-150mm | TriangularTotalLength: 300mm ±2mm Blade Length: 150mm±1mm Blade Width: 16mm±1mm Blade Material: High Carbon Steel Blade Hardness: 55-60HRC With Handle Material Laminated Wood Steel ring pacing Size Dia 8”X4inch long Color Brown |
| 3 | Scraper Half Round | Half roundTotalLength: 300mm ±2mmBlade Length: 150mm±1mm Blade Width: 20mm±1mm Blade Material: High Carbon Steel Blade Hardness: 55-60HRC With Handle Material Laminated Wood Steel ring pacing Size Dia 8”X4inch long Color Brown |
| 4 | Scraper Flat | FLAT TotalLength: 300mm ±2mm Blade Length: 150mm±1mm Blade Width: 20mm±1mm Blade Material: High Carbon Steel Blade Hardness: 55-60HRC With Handle Material Laminated Wood Steel ring pacing Size Dia 8”X4inch long Color Brown |
| 5 | Different Profile gauges (Plate type) - For demonstration-Metric Standard | Simple tracing of complex contours Elements can be slotted in series Elements can also be connected at an angle Slim line design for easy transfer of profile lines to a work piece With millimeter and inch scales racing elements each 20 cm long Angle connector Plastic box Tracer pin dimensions 85 x 0.8 mm Measuring depth 50 mm |
| 6 | Thermostat | Working conditionGenerally, about 200 degrees F, 95 degrees CParts catalogue suitable sketch on Vinyl Board Suitable for Heavy vehicleMaterial Brass and MS |
| 7 | Slip-on Forged steel Flange 150NB, ANSI-B16.5,Class#150 | ASME B16.5 Slip On Flange Flange Size : 6? InchOD of Flange 279 mm ID of Flange 170.7 mm Thickness 25.4 MM Face Dia 216 mm Hole Size 12.50 mm No. of Bolt Holes :- 04 Nos. Material M.S Coating Flange Faces : Hot Dip Galvanized |
| 8 | Lathe tools bit.6 mm x 75 mm HSS/Carbide | Compliance: Confirming to IS : 11143-1991 Length \"L\": 75mm (± 1.5 mm) Width \" W\": 6 mm Material: HSS-T42 / S400Finish: Milled / GroundHardness: 65 - 69 HRCSurface Treatment: Bright finish |
| 9 | VACCUM GAUGE | Inches of mercury (Hg) on a scale of 0 to 30, and the metric equivalent. Size = 4” Dial Metal BodyRubber hose pipe to connect combustion chamber Should be supplied in Wooden / Plastic Box with proper cushioning |
| 10 | Bench working.-2400 x 1200 x 900 mm | Working table size 2400 x 1200 x 900 mm (8x4x3) fit M.S. angle 50x50x6mm frame Cover of wooden from 1 inch stop of wooden plank thickness Support the leg size 50x506mm Color Mantle Gray Voice fitting M.S Angle 75x75x6mm Frame 6 No. Sam Dustan Welding |
| 11 | Lathe tools bit.8 mm x 75 mm HSS/Carbide | Compliance: Confirming to IS : 11143-1991 Length \"L\": 75mm (± 1.5 mm) 165.4 Width \" W\": 8 mmMaterial: HSS-T42 / S400Finish: Milled / GroundHardness: 65 - 69 HRC Surface Treatment: Bright finish |
| 12 | Lathe tools bit. 10 mm x 75 mm HSS/Carbide | Compliance: Confirming to IS : 11143-1991 Length \"L\": 75mm (± 1.5 mm) Width \" W\": 10 mm Material: HSS-T42 / S400 Finish: Milled / GroundHardness: 65 - 69 HRC Surface Treatment: Bright finish |
| 13 | Wing compass.-254 mm or 300 mm | Color: Silver 100.3 Size: Up to 300 mm Material: Mild Steel Scribing Capacity: Up to 325mmMaterial for Legs: Carbon & Alloy SteelOthers: Free Cutting Steel Finish for Legs: PolishedRest parts: Auto BlackHardness for Tip: 50 - 55 HRC Spring: 45 - 50 HRCProper rust preventive packing |
| 14 | Blow Lamp-0.5 liter | Generally conform to I.S. 841 - 1983 Material Used: Brass & Iron Steel Additional Name: Brass Pressure Kerosene Blow Lamp Torch Type Soldering Torch, Brazing Torch Should be Longer service life Smooth-finish Should be Resistance against corrosion Should be Precisely designed Top quality ,Extremely durable Capacity: 0.5 Liters (± 10 %) |
| 15 | Stop cock 25NB (2-way, Threaded end) | Compact design for an aesthetic appeal Casting: 100% virgin Brass Ingots certified for 63% Copper to ensure flawless Casting Chrome Plating: Robotic electroplating for everlasting lustrous shine Dimensions: 16.5 x 11.2 x 7.6 cm Weight: 1 Kg 117.7Spindle Size: BSP 1/2\" Cartridge Size: Not applicable |
| 16 | Lathe tools H.S.S. Tipped set. | Size: 16 X 16 mm Overall Length \"L\": 110 mm Insert Grade: Coating Carbide Surface Finish Polished Thickness 2mm High resistance Fine robustness High compression strength Fine wear resistance High resistance |
| 17 | Pipe threading die with handle | Size: 1/2”,3/4”-&1”inch Die: HSS 122.4 Stock: Iron Handle: Mild Steel Width 10 cm Diameter 20 mm Weight 5Kg Handle size 35cm Knurling grip In The Box 1 Pipe Die Set, 3 DIE, 1 HANDLE |
| 18 | Lapping plate Dia. -6\" | Min Diameter 100 mm Max Diameter 1000 mm Flatness tolerance 4.0 microns Grooves 3 mm Pitch 25 mm Surface Material Cast Iron Handle Material M S STEEL Material specification and constructional features similar to Cast Iron Surface Plates. Type, Round type Top surface provided with 3x3 mm grooves at a pitch of 25-30 mm. Top surface offered duly hand-scrapped/lapped finish M.S. Handles provided for lifting and handling for sizes up to 630 x 630 mm |
| 19 | Arm strong type tool bit holder, Right hand | Hand off Tool: · Right Cranking Angle: · 95 Degree Length (l1): · 80.0mm Width(b): · 12.0mm Thickness(h): · 12.0mm Function Value(f): · 16mm CompatiblewithInsert: · CCMT 09T3 ClampingScrew: · M3.5 X 11.0/T15 ClampingKey · T15 Material Cast steel |
| 20 | C.I. Sluice / Gate valve (flanged type) 150NB, Class# 150 Flange: ANSI125-B16.1 | Basic Indicative Diagram Design & construction: API 600, API 6D Face to face length: ASME / ANSI B16.10 Connections & dimensions: ASME / ANSI BASME / ANSI B 16.25Flanged: RF ANSI #150 Pressure & temperature: ASME / ANSI B16.34 Test: API 598Fig. 1501A: body st.st. CF8M / trim 316 Fig. 1501H: trim n.8 (body seat facing satellite) Material body- bonnet cast steel A216WCB, GP240GH+N StemA182 F6 Body seat facing A182 F6 Wedge ring facing A182 F6 Stem packing graphite Gasket graphite Painting high chlorinated polyethylene HCPE |
| 21 | Anvil - 50 Kg with stand | Total Length: 515 ±2mm Total Width: 155 ± 1mm Base Length: 265 ± 1mm Height: 240 ± 1mm Total Weight: 50Kg Material: Ductile Cast-iron Suitable stand should be supplied for Anvil |
| 22 | Carbide Wear Block.1 mm - 2 mm | This set is made up of two gauge blocks and offers you the following benefits: Wear-resistant even with frequent use of individual gauge blocks Corrosion-resistant No burrs caused by accidental mishandling Abrasion-resistant Size 05-1000mmWooden / Plastic Box with proper cushioning |
| 23 | V-Block pair with clamps-150 x 100 x 100 MM | Material IS-2949-1992 Alloy steelTotal Length: 150mm ±1mmTotal Width.: 100mm±0.2mm Total Height: 100mm± 0.2mm Angle: 90DegreeVeerunout: 10µ Clamping capacity: 25mm Hardness: 55 HRCAccuracy 4 µm or betterMaterial should be resistant to corrosion, impact and breakage Clamp: Material –cast Iron, c type with M12 Threaded Screw |
| 24 | Lifting sling 8mm Nominal Dia. Single leg sling | Up to 800kg capacityVariations available: Soft Eyes each end, Thimble Eyes each end, Masterlink c/w Sling Hook & Catch M Height of Lift as standardUp to 10M available BS EN13414-1:2003 taintless Steel available upon request Shape Flat Capacity 2 Ton provide a wide assortment of Single Leg Wire Slings Length 2 met |
| 25 | Power tools for fastening-Capacity 10-18mm | Power(Watts) 2000 Voltage 240 Size Air Volume(LPM) Low300 High500 Tmperature Setting: Low:50-450 High: 50-600 Air Volume(LPM): Low:300 High:500 Rated Input Power: 2000 W Net Weight: 0.700 kg Handle Housing Material: Aluminum, Front case material: Steel Max. Torque 745 Nm (@15s). Twin hammer mechanism with front Exhaust 3 speed position control to adjust tool speed Impact sockets in Blow Mould Case Hardness of Impact sockets 38 - 55 HRC with Super Grip Profile Black Oxide Finish Brand & Size etched on each individual socket to ensure quick & convenient Identification |
| 26 | Trammel 300 mm | Beam size 300mm ±2mmScribes circle Diameter: 600 mm±2mm Should be useful instrument for draftsmen, tool make sand machinist with Fine adjustment or accurate layout work |
| 27 | Stud Extractor EZY – out-Set of 8 | Stud screw extractors will remove any stud, screw, pipes and bolts.., Material-High carbon steel (Drop forged) Damaged Screw Extractor Easy Out Set Bolt Stud Remover Tools Kit DIY 8Pcs/Set Features: Reliable Quality- Made from carbon steel and are tempered twice for extra hardness and durability. Works on wood and machine screws, as well as flat, hex, or painted over screws.8- piece heavy duty steel extractor different sizes of screw extractor to meet different needs.These extractors will remove most kinds of damaged, stripped, rusted, broken, or stuck screws from any wood or metal surface with relative ease.The new two water pipe extractors, designed for the broken water pipes. It can remove some of the common screwdriver cannot be disassembled damaged bolts, screws, bolts and pipes.Reverse thread bits easily remove screws, bolts, studs, and threaded pipe fittings.Drill a pilot hole in the fastener.Choose a suitable bolt extractor and insert it into the hole.Use a wrench to turn the bolt extractor anticlockwise to remove. Screw extractor size includes:#1 for 4-6mm , #2 for 6-8mm, #3 for 8-11mm, #4 for 11- 14mm, #5 for 14-18mm, #6 for 18-25mm, 7# fo 25-35mm, 8# for 35-45mm Material: Alloy SteelPackage Included: 8pcs Set Screw Stud Extractor Remover |
| 28 | Drill Drift (May be manufactured in- house) 200 mm hardened and Black finish | Finish : Black Oxide Material MT2TOMT5SET Fits Morse Taper Sockets/Sleeves L1=150MM L3=25MM B= 20mm S=5mm Material : Quality Tool Steel |
| 29 | Damaged old spur gear to fit 50mm dia. Shaft | Material : Mild Steel Shaft dia. : 50 mm Module: 2 mm. Number of Teeth: 48 nos Tooth Pitch 4.50 mm Tooth thickness 3.14 mm Thickness of gear 20 mm.Outside Diameter 100 mm |
| 30 | Arm strong type tool bit holder. Straight | Hand off Tool: · Straight Cranking Angle: · 95 Degree Length (l1): · 80.0mm Width(b): · 12.0mm Thickness(h): · 12.0mm Function Value(f): · 16mm CompatiblewithInsert: · CCMT 09T3 ClampingScrew: · M3.5 X 11.0/T15 ClampingKey · T15 167.11 Material Cast steel |
| 31 | Arm strong type tool bit holder Left hand | Handoff Tool: · Left hand Cranking Angle: · 95 Degree Length (l1): · 80.0mm Width(b): · 12.0mm Thickness(h): · 12.0mm FunctionValue(f): · 16mm Compatible With Insert: · CCMT 09T3 Clamping Screw: · M3.5 X 11.0/T15 Clamping Key · T15 |
| 32 | Mallet Dia. 100 mm X 150 mm | Total Length: 325 mm ± 3 mm Max. Width. 128 ± 1 mm Min. Width: 112 ± 1 mm Thickness: 60 mm ± 1 mm Wood material: Hard Wood Handle grip is secured by a long taper Should be light weight for fine working Finishing: Fine finishing with body or chamfered.Should easy to operate for operator during hammering |
| 33 | Stake Grooving.100 X 100 X 300 mm | Usage/Application Industrial Material SS 145.4 Length 300 mm Width 100 mm Thickness 100 mm Shape T shape |
| 34 | MARKING TABLE-900X900X900 mm | Marking table — provides a true surface from which to work. Angle plates — assist in holding the work piece perpendicular to the table. Scriber — is the equivalent of a Pen or pencil. It literally scratches the metal surface leaving behind a fine, bright line. Marking Table-900X900X900 mm Material Frame : Cast Iron CI angle 50x50x6mm frame Cover of GI sheets Support 4 Handle size Die 30mmXL150mm Color: Oil Paint Gray Finish: Micro finish surface Hardness: Std Is |
| 35 | Stake Hatchet with Leg- 300 X 200 X 20 MM | Usage/Application Gardening Material SS LengthWidth High 300 mm 200 mm 20 mm Country of Origin Made in India Shape T Shape |
| 36 | Adjustable pipe chain tongs to take pipes up to 300 MM | Generally Conforming To I.S.4123-1998 Drop forged jaws with high grade Steel Accurately machined jaw teeth on both sides of the jaw to Provide firm gripping & easy for reverse operation Length:350mm Suitable For Pipe Ø 90mm |
| 37 | Tube/ tyre vulcanizing machine 220 V | Heater Capacity 400W x 2With different types of Die & Mold Tire Auto Repair Machine, Vulcanizing Machine, Vulcanizer Adjustable Height Tower Tire Spreader Tool for Light Truck and Car Working voltage 220V Watts 800W (400X2) Temperature 140-150°C Timer Scope 0-120 Minutes With Standard dies and mould. Item Weight 15.84 pounds (7.13 kg) Product Dimensions 17.72 x 7.87 x 13.78 inches (45 x 20 x 35 cm)or Higher as per std Vulcanizing repair process cures the patch and inner tire lining to form a dense, sealed repair job. An adjustable, swing-open, rotating C-frame cavity simplifies tire loading and unloading while maximizing stability Simple, one-man operation. Repairs tread, shoulder and sidewall. Large-capacity, fully rotating Cframe accommodates different wheel sizes and allows for vertical or horizontal repairs Energy and cost efficient for lower operating costs. Lightweight, self-standing design offers portability and maximum stability. Doesn’t require any time-consuming tensioning straps Adjustable height tower. Contoured inner and outer curing heads conform to a variety of tire profiles Long-life Acme thread hand-wheel screw applies over 4,000-lbs. of pressure and heat for maximum adhesion of patch to casing Handles long sidewall repairs. Cures both patch and plug at the same time. Curing heads can be operated individually or simultaneously for maximum repair efficiency. Constant controlled heating elements maintain optimum temperature |
| 38 | Dowel pin (straight) Dia. -1” Length -4\" (Mat: Stainless Steel) ( THIS ITEM IS CONSUMABLE ) | Material Stainless Steel Die 1 INCH Material Grade SS304 Surface Finish Polished Length 1-4 inch Material HSS Hardness is std Finish Steel finish |
| 39 | Washer, clutch, keys, jib, cotter & minimum 25mm size, carbon steel Material | Thickness: About 0.8mm. Color: Silver While 25mm bore size, # 428 Chain go kart Clutches engine up to 13hp Product Specs: Description 14 Tooth 25mm Bore |
| 40 | Pulleys (for V-belt or Flat belt) to fit on 50mm dia. Shaft with key slot | Applicable Industries: Manufacturing Plant, Machinery Repair Shops, Construction works , Energy &Mining Type: V-belt pulley Material: Casting & forging steel Pulley Size: 1SPZ50 Maximum Bore: 50mm Pulley Weight: 3 Kg Belt size A 38 Type: Flat pulley Material: Casting & forging steelMaximum Bore: 50mm Pulley Weight: 3 Kg Belt size 50 mm |
| 41 | Jigs & Fixture (sample)-For demonstration | Type Drilling jig Surface Powder Coated Finishing Technique Hot Rolled Hardness 50-70 HRCTensile Strength 100-300Mpa Shape Square Usage/Application Industrial Material Stainless Steel Surface Finishing Powder Coated Technique Hot Rolled Design Standard customized Corrosion resistant Easy to use Excellent finish |
| 42 | Machine maintenance manual for Lathe, Pedestal grinder, Drill Machine, Power saw | (As per AT Provide to copy 02 no’s of Service Manually and Operating Manually of each Machine Purchase by DVET /INSTITUTE) |
| 43 | Packing gasket PTFE gasket roll small size | Thickness 1mm to 15mm Size 1/2\" to 20\" Material PTFE Usage/Application Chemical Industry Shape Round / Square Country of Origin Made in India |
| 44 | Caps screws M6, M8, M10, M12 | Steel DIN7984 Metric Hex Hexagon Socket Thin Low Short Profile Head Allen Cap Screw Bolt L=6-50mm Bolt L=8-50mm Bolt L=10-50mm Bolt L=12-50mm Type of Product : Allen Cap Screw Dia : M6,8,10 to mM12 Length : 12 mm |
| 45 | Adjustable pipe die set BSP-cover pipe size 1\" or 3/4\" | Size : 1” or-3/4-inch Die : HSS Handle : Mild Steel Width: 10 Cm Length: 35 cm Steel Diameter: 20 mm Weight: 5kg Die Includes: Die Handle, Bush ,Pipe ,Key W |
| 46 | Standard Tap screws (Black Allen head) M3, M4, M5, M6, M8, M10, M12, M14, M16 | sales Bolt M5 x 25mm Allen Bolt (Pack of 25) Socket Head Cap Screws Grade 12.9 Alloy Steel Black Oxide Allen Socket Drive Full Thread (Alloy Steel) Type of Product : ALLEN SOCKET HEAD CAP SCREW Length : 10,15.,20,25,30,Material Alloy Steel Black Oxide Thread Size : M3, M4, M5, M6, M8, M10, M12, M14, M16 |
| 47 | V-belt and Flat belt to fit on pulley-to fit on pulley | V-Belt Type Industry Number A42 Number of Ribs1 Outside Length44 Inch Top Width1/2 Inch Thickness 5/16 Inch Material Fabric Cover, Rubber Body Construction Wrapped Temp. Range-22 Degrees to 194 Degrees Type: Flat-Belt Product name: Flat Belt Crane, Port Lifting Machinery, Mining Dimensions: Width 20mm Length 2500mm Thickness 2.6mm Material Fabric Cover, Rubber Body Industry Feature: Heavy Duty Machinery Packing |
| 48 | Steel keys to fit with key slot Of shaft & pulley | Size:3 x 3 mm to 50 x 50 mm Material: Material Tensile Strength: Medium Finish: Zinc Coated Length: 4 to 8 Inch Size: 3 x 3 mm to 50 x 50 mm Material: Material Tensile Strength: Medium Finish: Zinc Coated Length: 4 to 8 Inc |
| 49 | Pipe cutter wheel type.6 mm to 25 mm | The Baum - 6/25 mm Pipe Cutter used by plumbers to cut pipe. The 6/25 mm Pipe Cutter is a manually operated pipe, and the tube cutter typically consists of a curved jaw housing, a blade, and a handle that enables an operator to grasp the pipe in the cutter\"s jaws and rotate the entire cutter around the pipe.The Pipe Cutter produces a clean-cut. The 6/25 mm Pipe Cutter often has a faster, cleaner, and more convenient way of cutting.Material. Ms and GI pipe dia 6 to 25mm Rotated around the pipe in a 360-degree circle Body Material Cast Iron Should Be Provided With Long shank |
