Madhya Pradesh State Cooperative Dairy Federation Limited has published Purchase Of Spare Parts, At Cattle Feed Factory, Pachama Purchase Of Spare Parts, At Cattle Feed Factory, Pachama , Name Of The Itemfor Pachama , Pallet Mill Die 8Mm Hole Super Senior Extra Wide Size: 630 Mm Od 520Mm Id222 Mm Phase, 17 Rows Of Hole. Submission Date for this Tender is 24-12-2021. Spare Part Tenders in Bhopal Sahakari Dugdh Sangh Maradit, Bhopal Madhya Pradesh. Bidders can get complete Tender details and download the document.
Sl. No. | Item Description |
1 | NAME OF THE ITEMFOR PACHAMA |
2 | Pallet Mill die 8mm hole Super Senior extra wide Size: 630 mm OD 520mm ID222 mm Phase, 17 Rows of Holes with straight caller & m-20x12 holes both sides on 565 PCD |
3 | Roller Shells “V” grooved for above Size 250mm OD 180mm ID(Suitable for Bearing no. 32220, 182 mm wide |
4 | Roller Assembly Complete with shell & Bearing etc. Bearing SKF/FAG/ZKL |
5 | Die Holder Assembly Complete with “T” Shaft, Bearings 32324 & 32224, Bearing covers, Oil Seals etc. Bearing SKF/FAG/ZKL |
6 | Die Holder only (Alloy Steel Forging) |
7 | “T” Shaft with centralized greasing system |
8 | i) Eccentric Shaft (Alloy Steel) (Spare for Roller Assembly) |
9 | ii) Middle Spacer 51 mm wide(Spare for Roller Assembly) |
10 | iii) Bearing Cover Plate(Spare for Roller Assembly) |
11 | iv) Bearing Pressing Plate(Spare for Roller Assembly) |
12 | v) Circlip 180 mm Inner(Spare for Roller Assembly) |
13 | vi) Lock nut for Eccentric Shaft m-20(Spare for Roller Assembly) |
14 | vii) Lock Nut Washer for aboveMB-20(Spare for Roller Assembly) |
15 | viii) Clamping Device (Setting Ring of male female rings)(Spare for Roller Assembly) |
16 | ix) Centre Bolt for roller Alen Type (Unbreako/ TVS/LPS)(Spare for Roller Assembly) |
17 | x) Nut for Centre Bolt Attached with 1 male ring & Pin (Spare for Roller Assembly) |
18 | Front scraper assembly |
19 | Studfor front scraper assembly |
20 | Roller locking Assembly with Two Disc and master plate |
21 | Share Pin Block |
22 | Share Pin 18 mm Dia |
23 | Paddles for conditioner of 330 mm die of SS-304 with Stud and Nut |
24 | Die Ring rear for Straight collar die (Alloy Steel EN-9) |
25 | Die Ring front for Straight collar die (Alloy Steel EN-9) |
26 | Die cover with 4 Hooks size 520 OD x 340 mm ID x 130 mm wide made of SS 304 x 3 mm thick plate SS-304 |
27 | Main Bearing cover Plate front with Oil Seal 180-150-13for Bearing 32324 |
28 | Main Bearing cover Plate Rear with Oil Seal 170-150-13 for Bearing 32224 |
29 | Main Bearing Pressing Ring front |
30 | Main Bearing Pressing Ring rear |
31 | Pallet Die Guard Assembly with Pallet cutter made of 6 mm thick SS 304 Plate |
32 | Feeder Complete with screw about 02 Meter long400 mm Dia |
33 | Pallet Mill Main Pully SPC Section 9 Grove x 1220 mm Dia close grain CI Dynamically balanced +- 2 Grms. |
34 | Pallet Mill Counter Pully SPC Section 9 Grove x 230 mm Diaclose grain CI Dynamically balanced +- 2 Grms. |
35 | Die Bolt 20x50 mm High Tensile (Unbreako/ TVS/LPS |
36 | Die Bolt 20x140 mm High Tensile (Unbreako/ TVS/LPS |
37 | Die Bolt Washer (Spacer) |
38 | Bush for “T” Shaft (Roller Holding Bush) |
39 | Elevator Belt 10” 4 Ply |
40 | Elevator MS Bucket 8*5, 3 Hole |
41 | Elevator Bucket Bolt(3*8, 1 1/2) |
42 | Twin Rotor With Motor 10 HP Complete |
43 | Fidder Condisnior Soft Complite SS 2 Mtr. |
44 | Sprocket Duplex 1" 10 Teeth |
45 | Sprocket Duplex 1" 14 Teeth |
46 | Sprocket Duplex 1" 18 Teeth |
47 | Sprocket Duplex 1" 19 Teeth |
48 | Sprocket Duplex 1" 25 Teeth |
49 | Sprokit Duplex ¾" 14 Teeth |
50 | Sprocket Duplex ¾" 95 Teeth |
51 | Sprocket Duplex 1" 50 Teeth |
52 | Side Glass 200 MM PVC Round |
53 | Vindish charger 3 HP Motor With Gair Box Complete |
54 | Elevator Botom Drum Complete With Bearing 4mm seet |
55 | Pellet Mill Hopper SS Make |
56 | Betch Selector Switch 15 Motor |
57 | Pellet Bin SS Make 4 MM Seet 6 M.T. |
58 | Pellet Mill Cover SS 5 MM Seet with Gard Complete |
59 | Molases Pump 4" With Flench Complete |
60 | Molases Pump 2" With Flench Complete |
61 | HammerMill Beatersize 140 x 60 x 6 mm thick |
62 | Hammer Mill Sieve 5 mm Hole perforation size about 880 x 720 x 3 mm thick |
63 | Hammer Mill Beater Holding Rod 18 mm Dia |
64 | Hammer Mill Beater Spacing Bush |
65 | Elevator Top Drum about 600 mm Dia x 300 mm width complete with shaft about 800 mm length x 50mm Dia suitable for Bearing 1211 K |
66 | SS 304 Wire Mesh For Vibro 5MM OPG x 1.50 MM Dia Size 72” x 72” |
67 | Chain Conveyor Chain size 285 |
68 | Chain Conveyor Chain size 385 |
69 | Chain Conveyor Spocket 9 teeth with shoft 50 mmx600 mm |
70 | Chain 1" simplex |
71 | Elivator Jacket 300x290 mm |
72 | Pelet Cooler Blower Empeler S.S with soft and bearing |
73 | T-Shaft Gun Metal Bush |
74 | 150 HP Motor Bes Frem |
75 | Slate Conveyor Chain |
76 | Slate Conveyor Sprocket |
77 | Motor with Gair Box 5 HP-127 RPM PBL |
78 | Motor 3 HP- 80 RPM PBL |
79 | Pully 14” 2 Group B Section |
80 | Pully 3” +4” 2 Group B Section |
81 | Sprokit 15 Theeth Duplex ¾ |
82 | ¾ Duplex Chain |
83 | Duplex Chain 1" Roller |
84 | Joot Seprator |
85 | Pellet Cooler Assentric |
86 | Pellet Sheev Jaali 6 mm SS |
87 | Chain Conveyor Roll |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail