Supply, Fixing And Placing Various Office Furniture At Capacity Building And It Training Centre And Helpdesk At Head Office Of Commercial Tax Department, Jaipur Supply, Fixing And Placing Various Office Furniture At Capacity Building And It Training, Commercial Tax Department, Jaipur-Rajasthan

Supply, Fixing And Placing Various Office Furniture At Capacity Building And It Training Centre And Helpdesk At Head Office Of Commercial Tax Department, Jaipur Supply, Fixing And Placing Various Office Furniture At Capacity Building And It Training Centre And Helpdesk At Head Office Of Commercial Tax Department, Jaipur Table With Pedestal, Side Unit& Back Unit: The main desk is provided with the wire management system. The Main table shall be of size: 3000 Width mm x 1200 mm Depth x 750 mm height. Top surface of the table shall made up of 50mm thick MDF board duly finished with Veneer and final coating of PU high gloss. The Main desk should contain in Smart Case - space slides effortlessly in style. Side panel made up of 50mm thick MDF board duly finished with Veneer and final coating of PU high gloss. Modesty made up of 18mm thick MDF board duly finished with Veneer and final coating of PU high gloss. The mobile Pedestal shall be of size: 480 Width mm x 640 Depth mm x 600 Height mm. Mobile pedestal shall be made of 18mm thick MDF board duly finished with Veneer and final coating of PU high gloss. Side unit of Size: 1800 Width mm x 540 Depth mm x 750. The side unit Top surface shall made up of 50mm thick MDF board duly finished with Veneer and final coating of PU high gloss. Modesty, side panel & understructure made up of 18mm thick MDF board duly finished with Veneer and final coating of PU high gloss. The Back unit of size: 1500 mm width x 450 mm Depth x 1800 mm height. The back unit shall be made up of 18mm thick MDF board duly finished with Veneer and final coating of PU high gloss. Main desk , pedestal, side unit & back unit should be provided with all necessary hardware & fittings etc. 2 Sofa 3+1+1: Size of 1 seater sofa shall be 1010 (L) 920 mm (W) 950 (H) seating area length 560 mm & seating area width 510mm. Size of 3 seater sofa shall be 1960 (L) 920 mm (W) 950 (H) seating area length 1520 mm & seating area width 510mm. The frame material to be tropical wood + pinewood, Length of S-spring to be 510 mm, width of belt to be 40mm. The seat foam & back foam density to be 40kg/m3 upholstered with leatherette. The material for handle and leg to be wood and should be polish. 3 High Back Chair: The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with leatherette and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 52.0cm.(W) X 85.0cm.(H) SEAT SIZE: 52.0cm.(W) X 51.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20+/-2 for 25% compression. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 9.0cm (w) spine made of 0.8cm thick HR steel. The spine is black powder-coated. ARMREST ASSY: The armrest assy. comprises of three parts viz. the armrest support tube and P.U. armrest and the armrest top. The armrest tube assy. is made of 2.5cm(1) x 16 BG. M.S. E.R.W. support tubes and Chrome plated. The P.U. armrest is made of black integral skin polyurethane reinforced with M.S. insert. The armrest top is upholstered with foam & leather. The mechanism of the chair shall have following features : 360° revolving type, Knee Tilt system, 5- position locking with antilock back mechanism. Tilt tension adjustment and position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock is released. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminum it shall be fitted with 5 nos. twin wheel castor. The size of the pedestal shall be 62.0 +/- 1.0 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon. Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below with castor. All the metal parts have free from the dent, burrs and sharp edges, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 4 Center Table: The dimension of the table shall be (L) 1200 mm x (W) 600 mm x(H) 450mm, the material of the top shall be plywood with VENEER 18mm thick .The table support to be made of teak wood of size- 55x22mm .Center Table Leg to bemade of teak wood of size - 50x50mm & should be PU polished. 5 Corner Table: The dimension of the table shall be (L) 600 mm x (W) 600 mm x (H) 450mm, the material of the top shall be plywood with VENEER 18mm thick .The table support to be made of teak wood of size- 55x22mm .Center Table Leg to bemade of teak wood of size - 50x50mm & should be PU polished. 6 Visitor Chair: The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with leatherette and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 48.0cm.(W) X 65.0cm.(H) SEAT SIZE: 48.0cm.(W) X 48.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 9.0cm (w) spine made of 0.8cm thick HR steel. The spine is black powder-coated. The tubular frame is cantilever type & made of 4.0cm x 2.0cm x 0.2cm.thk M.S. E.R.W tube. All the metal parts have free from the dent, burrs and sharp edges, Is have pickled before stove enamellings to remove grease, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 7 Office Table With Three Drawer & Keyboard : Overall size- 1200(W)X600(D)X750(h) in mm. Table top made of 18 mm pre-laminated particle board with 2mm thick PVC edge beading on all sides. The modesty panel and side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. 3 drawer unit and Keyboard tray made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. Glide screws is provided at the bottom of the legs forlevel adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. 8 High Back Chair:The seat and back are made up of 1.2 cm thick hot pressed plywood upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumber support for extra comfort. Back foam size 470(W) x720(H) mm. seat foam size 480(W)x 465(D) mm. The one piece armrest made of black integral skin polyurethane reinforced with M.S. insert. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.6cm thick HR steel. The center tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. The pneumatic height adjustment have an adjustment stroke of 12.0 cm. The Telescopic bellow assy:- The bellow is 3 piece telescopic type and injection molded in black polypropylene .The pedestal is injection molded in black 30% glass filled Nylon. A 10.5 dia forged bright zine plated M.S. caster pin press- fitted into each prong for holding the castors. The pedestal shall be 700 mm pitch- centre- dia. (750 mm with castors).The twin wheel casters are made of nylon . Overall Dimensions of Chair as measured from pedestal - Width-75. cm and Depth- 75.0cm. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any otherforeign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 9 Almirah Big: Product Size: 916mm (W) x 486mm (D) x 1981 mm (H)excluding levellers. Construction & Material Welded construction. 0.8 mm thick CRCA for Shelf & 0.8 mm thick CRCA for all other components. It should have multi bend construction with interlocking design and full length over lapping doors and sides. It should have three way bolting mechanism. The two doors should have hinge mounted on frame. The doors have one handle and lever locking mechanism with 6- Six lever SS Lock (Godrej or Equivalent). Shelving: Height wise Adjustable Shelves 4 Nos. Uniformly Distributed Load Capacity per full shelf is 80 Kg maximum. Leveler M10 Screw type leveler with plastic base. (add 10mm to unit height and additional 10mm for adjustment.). Lock and key. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 10 Visitor Chair: The cushioned seat assembly consists of insert moulded polyurethane foam upholstered with foam laminated mesh fabric. the insert moulded foam is assembeled over a load bearing plastic seat cover. The back made up of two piece injection moulded frame. The inner frame is upholstered with mesh fabric and mounted on the main assembly. Size of back (W)-48.5cm, (H)- 62.0cm & size of seat (W)-51.0cm x (D)-52.5cm. The sled base leg frame welded assembly made from MS ERW round tube of 25mm with 2mm thick with base plate for seat fixing. Visitor Chair frame is chrome coated. 11 Table With Pedestal & Side Unit :Table Size-1800(W)X900(D)X750(H) mm.Tabletop made of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glide screws is provided at the bottom of the legs for level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. The three drawer unit size- 680(H)x400(W)x450(D). Mobile pedestals is placed below table top. Mobile pedestals made of 18mm thick Pre laminated Particle board. The sides of drawers and facia made of 18mm thick pre laminated Particle Board. Back of the pedestal made of 9mm Pre laminated Particle Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles and four number poly-propylene castors is provided with the pedestal.Side Unit Size-900(W)X450(D)X750(H) mm. Tabletop made of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading.The side shutter and shelves are made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The back is made of 18mm thick Pre Laminated Particle Board. Each unit have lockable double door is fitted with hinges. Each unit have one numbers of adjustable shelves. Skirting is made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. 12 Table with Pedestal & Side unit: Table Size-2400(W)X1000(D)X750(H) mm.Tabletop made of 36 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glide screws is provided at the bottom of the legs for level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. The three drawer unit size- 680(H)x450(W)x500(D). Mobile pedestals is placed below table top. Mobile pedestals made of 18mm thick Pre laminated Particle board. The sides of drawers and facia made of 18mm thick pre laminated Particle Board. Back of the pedestal made of 9mm Pre laminated Particle Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles and four number poly-propylene castors is provided with the pedestal. Side Unit Size-1500(W)X450(D)X750(H) mm. Tabletop made of 36 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. Side unit shall have two openable shutter and three drawer at center. All exposed edges are sealed with 2mm PVC edge beading.The side shutter and shelves are made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The back is made of 18mm thick Pre Laminated Particle Board. Each unit have lockable double door is fitted with hinges. Each unit have one numbers of adjustable shelves. Skirting is made of 18mm thick Pre Laminated Particle Board. All exposed edgesare sealed with 2mm PVC edge beading. 13 Open File Unit :Overall size-1050(W)X450(D)X750(H) in mm. The open file unit made of 18 mm pre-laminated particle board with 2mm thick PVC edge beading on all sides. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glidescrews is provided at the bottom of the legs for level adjustment. 14 Providing and fixing of Workstation System (8 Seating) : One seater overall size-1200(L) 600 (D) Height of panel 1200 mm. Side panel and main panel shall be of 60mm. The 60mm panel comprises of 2 nos. Of vertical trims made of aluminum extrusions and Horizontal trims shall be made of aluminum extrusions at every division of tile/block. Block for 60mm panel’s thickness shall comprises of 38mm thick paper honeycomb + 9mm particle board on each sides + 0.6mm decorative laminate or fabric on both sides. The fabric shall be upholstered with particle board framing shall used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. Blocks shall be located in the mid segment of the panels and shall be provided with cut outs for mounting switch boxes (above the worktops). Fabricated bottom frame for 60mm panel comprises of L channels made of 2mm thick CRCA steel formed plates of 3mm thick HR steel & ERW steel tube of size 35x15x1.6mm thick in oval cross section welded together. This frame shall be bolted to the uprights with M6 screws. Top tiles shall be slid in to the panels from top before fixing the top horizontal. The top shall have white board / glass/ laminate tiles of approved shade. Laminated tiles shall be 9.0 mm thick pre-laminated particle board having all its edges with minimum 0.5 mm thick PVC edge banding. White board tiles shall be made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum0.5 mm thick PVC edge banding. Glass tiles - 4 mm thick toughened clear glass. Split Top shall be provided for two different finishes in single panels. Bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon and support clips made from PP co polymer. Bottom tiles shall be of Metal tiles made of 0.8mm thick CRC sheet. These uprights and horizontals are made of aluminum extrusion having material & have average wall thickness of 1 mm. The panels shall be joined to each other directly with joinery or with the help of post to form. Free standing modules shall be provided with stability bracket. The top trims and end trims for 60 mm shall be made from aluminum extrusion having material. All kinds of extrusions for 60 mm shall have average wall thickness of 1 mm. Top trim shall be press fitted on the horizontal extrusion. Die cast. aluminum alloy shall be provided according to the joineries. The worktop is made of 25mm thick pre laminated particle board with 2mm thick PVC edges bands all around all the edges are pressed with 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The work surface shall be provided with circular cut out of Dia.65mm for passing of wires. These cut outs shall be provided with ABS covers. Table top height – 750mm (including table top thickness of 25mm) Work surface bracket shall be mounted on to the Horizontal extrusion. 4 numbers of ribs are provided in the work surface for strengthening purpose. All the work surface shall be mounted on the work surface through round Philip head diameter 4 mm x 19 length having finish zinc plated. The panel legs shall provide to support panels. Panel legs shall fabricated by CO2 welding MS Tube of section 38 mm x 25 mm ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm over which an M8 Leveler is fitted, which allows for adjustment of the height by 25mm. Double and single side leg assembly: shall be provided to supporting panels & work surface. Wire carrier shall be madefrom 0.8 mm thick CRCA sheet. It shall be constructed with two parts, one shall be body & another shall be cover. It holds the cables & gives aesthetic appearance by covering all cables. Worktop supporting pedestal shall be provided having provision to fit with worktop and pedestal leg welded assembly fitted at the bottom. The pedestal unit shall be welded assembled with 0.6mm thick CRCA steel for body shell & drawer tray, 1.2 mm thick CRCA top and bottom stiffeners and 0.8mm thick CRCA rear side stiffeners. Drawers shall be provided with double extension precision ball slide with 10 lever Cam lock and centre locking arrangement. Handle. Easy to grip Full length Handle recess integrated into Metal drawer fronts. Construction - Pedestal leg assembly shall be fabricated by CO2 welding vertical MS Tubes of section 38 mm x 25 mm (38 mm x 25 mm x 16bg) inside which leveller holder plates of size 35x22x5mm are welded with horizontal bottom channel made of 2.0 mm thick CRCA sheet. Dimensions Pedestal height is 600 mm without leg assembly and 700 mm including leg assembly. Width of the pedestal shall be 400mm and depth shall be 450mm. Key board tray made of 1.2mm thick CRCA steel. Adjustable wheel mounted CPU trolley made of 1 mm thick CRCA steel. Pedestal, key board tray & CPU Trolley shall be provided with each workstation. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 15 Table: Main table Size-1500(W)X750(D)X750(H) mm. Table Tabletop made of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glide screws is provided at the bottom of the legs for level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. The three drawer unit size- 680(H)x450(W)x500(D). Mobile pedestals is placed below table top. Mobile pedestals made of 18mm thick Pre laminated Particle board. The sides of drawers and facia made of 18mm thick pre laminated Particle Board. Back of the pedestal made of 9mm Pre laminated Particle Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles and four number poly-propylene castors is provided with the pedestal.Side Unit Size-900(W)X450(D)X750(H) mm. Tabletop made of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading.The side shutter and shelves are made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The back is made of 18mm thick Pre Laminated Particle Board. Each unit have lockable double door is fitted with hinges. Each unit have one numbers of adjustable shelves. Skirting is made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. 16 Mid Back Chair:The cushioned seat assembly consists of insert moulded polyurethane foam upholstered with foam laminated mesh fabric. the insert moulded foam is assembeled over a load bearing plastic seat cover. The back made up of two piece injection moulded frame. The inner frame is upholstered with mesh fabric and mounted on the main assembly. Size of back (W)-48.5cm, (H)- 62.0cm & size of seat (W)-51.0cm x (D)-52.5cm. Armrest are injection moulded with height adjustable up to 4.5cm in 3 steps and width adjustable up to 20mm. The mechanism of chair have following features:360 degree revolving type, Front pivot Synchro mechanism, Tilt tension adjustment, 3 position tilt limiter with Anti-Shock feature. Spine bracket made of Iron piece connecting back with mechanism. The chair is provided with pneumatic height adjustment which shall have stroke of 10.0 cm. The pedestal made of die-cast polished aluminium. it fitted with 5 nos twin wheel castor. The size of the pedestal 62.0 cm pitch-centre-dia (70.0 cm with castors). The twin wheel castors are injection moulded in black nylon. 17 Providing and fixing of Workstation System (6 Seating) : One seater overall size-1200(L) 600 (D) Height of panel 1200 mm. Side panel and main panel shall be of 60mm. The 60mm panel comprises of 2 nos. Of vertical trims made of aluminum extrusions and Horizontal trims shall be made of aluminum extrusions at every division of tile/block. Block for 60mm panel’s thickness shall comprises of 38mm thick paper honeycomb + 9mm particle board on each sides + 0.6mm decorative laminate or fabric on both sides. The fabric shall be upholstered with particle board framing shall used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. Blocks shall be located in the mid segment of the panels and shall be provided with cut outs for mounting switch boxes (above the worktops). Fabricated bottom frame for 60mm panel comprises of L channels made of 2mm thick CRCA steel formed plates of 3mm thick HR steel & ERW steel tube of size 35x15x1.6mm thick in oval cross section welded together. This frame shall be bolted to the uprights with M6 screws. Top tiles shall be slid in to the panels from top before fixing the top horizontal. The top shall have white board / glass/ laminate tiles of approved shade. Laminated tiles shall be 9.0 mm thick pre-laminated particle board having all its edges with minimum 0.5 mm thick PVC edge banding. White board tiles shall be made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum0.5 mm thick PVC edge banding. Glass tiles - 4 mm thick toughened clear glass. Split Top shall be provided for two different finishes in single panels. Bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon and support clips made from PP co polymer. Bottom tiles shall be of Metal tiles made of 0.8mm thick CRC sheet. These uprights and horizontals are made of aluminum extrusion having material & have average wall thickness of 1 mm. The panels shall be joined to each other directly with joinery or with the help of post to form. Free standing modules shall be provided with stability bracket. The top trims and end trims for 60 mm shall be made from aluminum extrusion having material. All kinds of extrusions for 60 mm shall have average wall thickness of 1 mm. Top trim shall be press fitted on the horizontal extrusion. Die cast. aluminum alloy shall be provided according to the joineries. The worktop is made of 25mm thick pre laminated particle board with 2mm thick PVC edges bands all around all the edges are pressed with 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The work surface shall be provided with circular cut out of Dia.65mm for passing of wires. These cut outs shall be provided with ABS covers. Table top height – 750mm (including table top thickness of 25mm) Work surface bracket shall be mounted on to the Horizontal extrusion. 4 numbers of ribs are provided in the work surface for strengthening purpose. All the work surface shall be mounted on the work surface through round Philip head diameter 4 mm x 19 length having finish zinc plated. The panel legs shall provide to support panels. Panel legs shall fabricated by CO2 welding MS Tube of section 38 mm x 25 mm ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm over which an M8 Leveler is fitted, which allows for adjustment of the height by 25mm. Double and single side leg assembly: shall be provided to supporting panels & work surface. Wire carrier shall be made from 0.8 mm thick CRCA sheet. It shall be constructed with two parts, one shall be body & another shall be cover. It holds the cables & gives aesthetic appearance by covering all cables. Worktop supporting pedestal shall be provided having provision to fit with worktop and pedestal leg welded assembly fitted at the bottom. The pedestal unit shall be welded assembled with 0.6mm thick CRCA steel for body shell & drawer tray, 1.2 mm thick CRCA top and bottom stiffeners and 0.8mm thick CRCA rear side stiffeners. Drawers shall be provided with double extension precision ball slide with 10 lever Cam lock and centre locking arrangement. Handle. Easy to grip Full length Handle recess integrated into Metal drawer fronts. Construction - Pedestal leg assembly shall be fabricated by CO2 welding vertical MS Tubes of section 38 mm x 25 mm (38 mm x 25 mm x 16bg) inside which leveller holder plates of size 35x22x5mm are welded with horizontal bottom channel made of 2.0 mm thick CRCA sheet. Dimensions Pedestal height is 600 mm without leg assembly and 700 mm including leg assembly. Width of the pedestal shall be 400mm and depth shall be 450mm. Key board tray made of 1.2mm thick CRCA steel. Adjustable wheel mounted CPU trolley made of 1 mm thick CRCA steel. Pedestal, key board tray & CPU Trolley shall be provided with each workstation. . All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 18 Peacock Chair: Chair with low back support chair, chair base made out with wooden finish and chair seat and back structure duly made with medium density foam covered with fabric tapestry two nos. arm made with wooden finish 19 Table: Main table Size-1500(W)X750(D)X750(H) mm. Top made up of 25 mm thick pre laminate MDF board - edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The Modesty &Side panels made of 0.8 mm thick CRCA sheet with perforation on the sheet shall be uniform of 3mm dimension except 100mm four side border. Leg of the table made up of 50mm round CRCA steel pipe with 1.2m thickness. The three drawer unit size 674(H)x390(W)x440(D) shall be welded assembled with 0.6mm thick CRCA steel for body shell & drawer tray, 1.2 mm thick CRCA top and bottom stiffeners and 0.8mm thick CRCA rear side stiffeners. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 20 Desk & Bench (Three Seater): Desk Frame Size: 1800(L) x 400(D) x 750(H)mm. The Complete MS section to be powder coated in approved based high glosscolour& shade. Vertical supporting pipe is to be made of 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. Front of the seat, perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. The front row have full MS modesty panel. 25x3mm MS angle shall be used for top supporting which shall be connected one part with the table top and another from modesty border pipe. All steel structural components shall be processed and made from virgin material. Seat Frame Size: 1800(L) x 400(D) x 450(H) mm. Seat frame shall be made from Vertical supporting pipe is to be 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. Seat frame have perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. Seat frame mounting pedestal to be used like a desk frame. Seat shall be mounted on 25.0mm dia. & 1.6mm thick pipe. All steel structural components shall be processed and made from virgin material.DESK TOP& SEAT :Desk Top & Seat made up of 25 mm thick pre laminate particle board - edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function .BASKET : Basket shall be Made of 6mm thick Mild steel rod making a curved basket connected with the 50x50 mm square pipe support. FIXING: Fixing at site to be done with metal dash fasteners of 100x12 mm size grouted with chemical filter compound .Pedestal made of 2mm thick pressed HR steel base and shall be ribbed with 2 counters sunk holes for floor fixing. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 21 Steel 3 SeaterChair: 3 Seater Chair public places seating Chair of mild steel with arm. Material of main frame and Sheet and backrest - mild steel. Legs and Armrests are made of aluminum die cast and are Powder Coated for long life. Overall Size: Length -1760mm x depth 520mm x 775mm height. Colour of powder coting- silver. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 22 Mid Back Chair: seat & back made of 12mm thick hot pressed plywood, with fabric and moulded polyurethane foam. The back foam is designed with contoured lumber support for extra comfort. Back foam size 500(W) x490(H) mm. seat foam size 500(W)x 465(D) mm. The seat cover shall be injection moulded in black co- polymer polypropylene and back cover is vacuum formed from ABS sheets. The one piece armrest made of black integral skin polyurethane reinforced with M.S. insert. The armrests are scratch and weather resistant. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.6cm thick HR steel. The center tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. The pneumatic height adjustment shall have an adjustment stroke of 12.0 ±0.3cm. The Telescopic bellow assy:- The bellow is 3 piece telescopic type and injection molded in black polypropylene .The pedestal is injection molded in black 30% glass filled Nylon. A10.5 dia forged bright zine plated M.S. caster pin shall be press-fitted into each prong for holding the castors. The pedestal shall be 700 mm pitch-centre-dia. (750 mm with castors).The twin wheel casters are made of nylon. Overall Dimensions of Chair as measured from pedestal - Width-75. cm and Depth-75.0cm. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 23 Dining Table With Chair (6 Seater): Table of size: 1800(L) x 900(W) x 750(H) mm. Top surface of the table shall made up of 25mm thick Sheesham Wood and finished with melamine polish. Top shall be provided with 10mm thick clear toughened Glass with four SS Studs. The table supportLeg to be made of teak wood of size - 75x75 mm and supported with teak wood of size- 75x25mm. Chair of size: 450Wx480Dx900Hmm made of teak wood. Seat foam 50mm thick density of 40kg/m3 pasted on 12mm thick ply covered with good qualityof fabric.The entiredining table & Chair is to be finish by three coats of melamine polish on wood surface for smooth and protective finish. 24 Table: Main table Size-1800(W)X900(D)X750(H) mm. Top and side panel made up of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 06mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function .Understructure of the table made up of 40x40mm SQR MS pipe with 1.2m thickness. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns. 25 Conference Table: Size:7200(L) x 3000(W) x 750(H) mm. With Wire Manager. The top shall be 37 mm thick (18 mm mdf + 18 mm mdf + 0.6 mm laminate + 0.4 mm Membrane ) Edge Profile shall be waterfall edge 10 mm radius on top edge and 5 mm at bottom. In Understructure the Legs shall be made from 25 mm plain MDF having a straight profile with half round edges and with 0.6 mm thick post Forming laminate . Overall thickness of leg shall be 26.2 mm .The modesty panel in understructure shall be made from pre-laminated MDF boards of 18 mm thick with 2mm thick PVC edge beading on all sides. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. There shall be Wire Management wire carrier shall be made from 0.6 mm thick CRCA powder coated and carrier cover shall be made of 12 mm thick MDF painted all over. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreignelement before Powder coating. The minimum thickness of powder coated should be 40-50 microns.

INR 1180 /-

Refer document

INR 60.19 Lakhs /-

Name of Work:Supply, fixing and placing various iffice furniture at capacity building and IT Training Centre and Helpdesk at Head Office of Commercial Tax Department, Jaipur

Sl. No.	Item Description
1	Table With Pedestal, Side Unit& Back Unit: The main desk is provided with the wire management system. The Main table shall be of size: 3000 Width mm x 1200 mm Depth x 750 mm height. Top surface of the table shall made up of 50mm thick MDF board duly finished with Veneer and final coating of PU high gloss. The Main desk should contain in Smart Case - space slides effortlessly in style. Side panel made up of 50mm thick MDF board duly finished with Veneer and final coating of PU high gloss. Modesty made up of 18mm thick MDF board duly finished with Veneer and final coating of PU high gloss. The mobile Pedestal shall be of size: 480 Width mm x 640 Depth mm x 600 Height mm. Mobile pedestal shall be made of 18mm thick MDF board duly finished with Veneer and final coating of PU high gloss. Side unit of Size: 1800 Width mm x 540 Depth mm x 750. The side unit Top surface shall made up of 50mm thick MDF board duly finished with Veneer and final coating of PU high gloss. Modesty, side panel & understructure made up of 18mm thick MDF board duly finished with Veneer and final coating of PU high gloss. The Back unit of size: 1500 mm width x 450 mm Depth x 1800 mm height. The back unit shall be made up of 18mm thick MDF board duly finished with Veneer and final coating of PU high gloss. Main desk , pedestal, side unit & back unit should be provided with all necessary hardware & fittings etc.
2	Sofa 3+1+1: Size of 1 seater sofa shall be 1010 (L) 920 mm (W) 950 (H) seating area length 560 mm & seating area width 510mm. Size of 3 seater sofa shall be 1960 (L) 920 mm (W) 950 (H) seating area length 1520 mm & seating area width 510mm. The frame material to be tropical wood + pinewood, Length of S-spring to be 510 mm, width of belt to be 40mm. The seat foam & back foam density to be 40kg/m3 upholstered with leatherette. The material for handle and leg to be wood and should be polish.
3	High Back Chair: The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with leatherette and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 52.0cm.(W) X 85.0cm.(H) SEAT SIZE: 52.0cm.(W) X 51.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3 and Hardness = 20+/-2 for 25% compression. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 9.0cm (w) spine made of 0.8cm thick HR steel. The spine is black powder-coated. ARMREST ASSY: The armrest assy. comprises of three parts viz. the armrest support tube and P.U. armrest and the armrest top. The armrest tube assy. is made of 2.5cm(1") x 16 BG. M.S. E.R.W. support tubes and Chrome plated. The P.U. armrest is made of black integral skin polyurethane reinforced with M.S. insert. The armrest top is upholstered with foam & leather. The mechanism of the chair shall have following features : 360° revolving type, Knee Tilt system, 5- position locking with antilock back mechanism. Tilt tension adjustment and position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock is released. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminum it shall be fitted with 5 nos. twin wheel castor. The size of the pedestal shall be 62.0 +/- 1.0 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon. Overall dimensions of Chair shall be, Width of Chair - 70.0cm, Depth of Chair - 70.0 cm as measured from pedestal below with castor. All the metal parts have free from the dent, burrs and sharp edges, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
4	Center Table: The dimension of the table shall be (L) 1200 mm x (W) 600 mm x (H) 450mm, the material of the top shall be plywood with VENEER 18mm thick .The table support to be made of teak wood of size- 55x22mm .Center Table Leg to be made of teak wood of size - 50x50mm & should be PU polished.
5	Corner Table: The dimension of the table shall be (L) 600 mm x (W) 600 mm x (H) 450mm, the material of the top shall be plywood with VENEER 18mm thick .The table support to be made of teak wood of size- 55x22mm .Center Table Leg to be made of teak wood of size - 50x50mm & should be PU polished.
6	Visitor Chair: The back & seat is made up of 1.2 cm. thick hot pressed plywood upholstered with leatherette and moulded Polyurethane Foam. The back foam is designed with contoured lumber support for extra comfort. Back Size: 48.0cm.(W) X 65.0cm.(H) SEAT SIZE: 48.0cm.(W) X 48.0cm.(D).The polyurethane foam is moulded with density = 45 +/-2 kg/m3. SEAT-BACK CONNECTING SPINE: The seat and back are arrested together with a 9.0cm (w) spine made of 0.8cm thick HR steel. The spine is black powder-coated. The tubular frame is cantilever type & made of 4.0cm x 2.0cm x 0.2cm.thk M.S. E.R.W tube. All the metal parts have free from the dent, burrs and sharp edges, Is have pickled before stove enamellings to remove grease, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
7	Office Table With Three Drawer & Keyboard : Overall size- 1200(W)X600(D)X750(h) in mm. Table top made of 18 mm pre-laminated particle board with 2mm thick PVC edge beading on all sides. The modesty panel and side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. 3 drawer unit and Keyboard tray made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. Glide screws is provided at the bottom of the legs for level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover.
8	High Back Chair:The seat and back are made up of 1.2 cm thick hot pressed plywood upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam is designed with contoured lumber support for extra comfort. Back foam size 470(W) x720(H) mm. seat foam size 480(W)x 465(D) mm. The one piece armrest made of black integral skin polyurethane reinforced with M.S. insert. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.6cm thick HR steel. The center tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. The pneumatic height adjustment have an adjustment stroke of 12.0 cm. The Telescopic bellow assy:- The bellow is 3 piece telescopic type and injection molded in black polypropylene .The pedestal is injection molded in black 30% glass filled Nylon. A 10.5 dia forged bright zine plated M.S. caster pin press- fitted into each prong for holding the castors. The pedestal shall be 700 mm pitch- centre- dia. (750 mm with castors).The twin wheel casters are made of nylon . Overall Dimensions of Chair as measured from pedestal - Width-75. cm and Depth- 75.0cm. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any otherforeign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
9	Almirah Big: Product Size: 916mm (W) x 486mm (D) x 1981 mm (H)excluding levellers. Construction & Material Welded construction. 0.8 mm thick CRCA for Shelf & 0.8 mm thick CRCA for all other components. It should have multi bend construction with interlocking design and full length over lapping doors and sides. It should have three way bolting mechanism. The two doors should have hinge mounted on frame. The doors have one handle and lever locking mechanism with 6- Six lever SS Lock (Godrej or Equivalent). Shelving: Height wise Adjustable Shelves 4 Nos. Uniformly Distributed Load Capacity per full shelf is 80 Kg maximum. Leveler M10 Screw type leveler with plastic base. (add 10mm to unit height and additional 10mm for adjustment.). Lock and key. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
10	Visitor Chair: The cushioned seat assembly consists of insert moulded polyurethane foam upholstered with foam laminated mesh fabric. the insert moulded foam is assembeled over a load bearing plastic seat cover. The back made up of two piece injection moulded frame. The inner frame is upholstered with mesh fabric and mounted on the main assembly. Size of back (W)-48.5cm, (H)- 62.0cm & size of seat (W)-51.0cm x (D)-52.5cm. The sled base leg frame welded assembly made from MS ERW round tube of 25mm with 2mm thick with base plate for seat fixing. Visitor Chair frame is chrome coated.
11	Table With Pedestal & Side Unit :Table Size-1800(W)X900(D)X750(H) mm .Tabletop made of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glide screws is provided at the bottom of the legs for level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. The three drawer unit size- 680(H)x400(W)x450(D). Mobile pedestals is placed below table top. Mobile pedestals made of 18mm thick Pre laminated Particle board. The sides of drawers and facia made of 18mm thick pre laminated Particle Board. Back of the pedestal made of 9mm Pre laminated Particle Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles and four number poly-propylene castors is provided with the pedestal.Side Unit Size-900(W)X450(D)X750(H) mm. Tabletop made of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading.The side shutter and shelves are made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The back is made of 18mm thick Pre Laminated Particle Board. Each unit have lockable double door is fitted with hinges. Each unit have one numbers of adjustable shelves. Skirting is made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading.
12	Table with Pedestal & Side unit: Table Size-2400(W)X1000(D)X750(H) mm .Tabletop made of 36 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glide screws is provided at the bottom of the legs for level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. The three drawer unit size- 680(H)x450(W)x500(D). Mobile pedestals is placed below table top. Mobile pedestals made of 18mm thick Pre laminated Particle board. The sides of drawers and facia made of 18mm thick pre laminated Particle Board. Back of the pedestal made of 9mm Pre laminated Particle Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles and four number poly-propylene castors is provided with the pedestal. Side Unit Size-1500(W)X450(D)X750(H) mm. Tabletop made of 36 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. Side unit shall have two openable shutter and three drawer at center. All exposed edges are sealed with 2mm PVC edge beading.The side shutter and shelves are made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The back is made of 18mm thick Pre Laminated Particle Board. Each unit have lockable double door is fitted with hinges. Each unit have one numbers of adjustable shelves. Skirting is made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading.
13	Open File Unit :Overall size-1050(W)X450(D)X750(H) in mm. The open file unit made of 18 mm pre-laminated particle board with 2mm thick PVC edge beading on all sides. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glide screws is provided at the bottom of the legs for level adjustment.
14	Providing and fixing of Workstation System (8 Seating) : One seater overall size-1200(L) 600 (D) Height of panel 1200 mm. Side panel and main panel shall be of 60mm. The 60mm panel comprises of 2 nos. Of vertical trims made of aluminum extrusions and Horizontal trims shall be made of aluminum extrusions at every division of tile/block. Block for 60mm panel’s thickness shall comprises of 38mm thick paper honeycomb + 9mm particle board on each sides + 0.6mm decorative laminate or fabric on both sides. The fabric shall be upholstered with particle board framing shall used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. Blocks shall be located in the mid segment of the panels and shall be provided with cut outs for mounting switch boxes (above the worktops). Fabricated bottom frame for 60mm panel comprises of L channels made of 2mm thick CRCA steel formed plates of 3mm thick HR steel & ERW steel tube of size 35x15x1.6mm thick in oval cross section welded together. This frame shall be bolted to the uprights with M6 screws. Top tiles shall be slid in to the panels from top before fixing the top horizontal. The top shall have white board / glass/ laminate tiles of approved shade. Laminated tiles shall be 9.0 mm thick pre-laminated particle board having all its edges with minimum 0.5 mm thick PVC edge banding. White board tiles shall be made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm thick PVC edge banding. Glass tiles - 4 mm thick toughened clear glass. Split Top shall be provided for two different finishes in single panels. Bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon and support clips made from PP co polymer. Bottom tiles shall be of Metal tiles made of 0.8mm thick CRC sheet. These uprights and horizontals are made of aluminum extrusion having material & have average wall thickness of 1 mm. The panels shall be joined to each other directly with joinery or with the help of post to form. Free standing modules shall be provided with stability bracket. The top trims and end trims for 60 mm shall be made from aluminum extrusion having material. All kinds of extrusions for 60 mm shall have average wall thickness of 1 mm. Top trim shall be press fitted on the horizontal extrusion. Die cast. aluminum alloy shall be provided according to the joineries. The worktop is made of 25mm thick pre laminated particle board with 2mm thick PVC edges bands all around all the edges are pressed with 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The work surface shall be provided with circular cut out of Dia.65mm for passing of wires. These cut outs shall be provided with ABS covers. Table top height – 750mm (including table top thickness of 25mm) Work surface bracket shall be mounted on to the Horizontal extrusion. 4 numbers of ribs are provided in the work surface for strengthening purpose. All the work surface shall be mounted on the work surface through round Philip head diameter 4 mm x 19 length having finish zinc plated. The panel legs shall provide to support panels. Panel legs shall fabricated by CO2 welding MS Tube of section 38 mm x 25 mm ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm over which an M8 Leveler is fitted, which allows for adjustment of the height by 25mm. Double and single side leg assembly: shall be provided to supporting panels & work surface. Wire carrier shall be made from 0.8 mm thick CRCA sheet. It shall be constructed with two parts, one shall be body & another shall be cover. It holds the cables & gives aesthetic appearance by covering all cables. Worktop supporting pedestal shall be provided having provision to fit with worktop and pedestal leg welded assembly fitted at the bottom. The pedestal unit shall be welded assembled with 0.6mm thick CRCA steel for body shell & drawer tray, 1.2 mm thick CRCA top and bottom stiffeners and 0.8mm thick CRCA rear side stiffeners. Drawers shall be provided with double extension precision ball slide with 10 lever Cam lock and centre locking arrangement. Handle. Easy to grip Full length Handle recess integrated into Metal drawer fronts. Construction - Pedestal leg assembly shall be fabricated by CO2 welding vertical MS Tubes of section 38 mm x 25 mm (38 mm x 25 mm x 16bg) inside which leveller holder plates of size 35x22x5mm are welded with horizontal bottom channel made of 2.0 mm thick CRCA sheet. Dimensions Pedestal height is 600 mm without leg assembly and 700 mm including leg assembly. Width of the pedestal shall be 400mm and depth shall be 450mm. Key board tray made of 1.2mm thick CRCA steel. Adjustable wheel mounted CPU trolley made of 1 mm thick CRCA steel. Pedestal, key board tray & CPU Trolley shall be provided with each workstation. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
15	Table: Main table Size-1500(W)X750(D)X750(H) mm. Table Tabletop made of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. Glide screws is provided at the bottom of the legs for level adjustment. Grommets (cut outs) is provided on table top for cabling. Grommets is provided with PVC cover. The three drawer unit size- 680(H)x450(W)x500(D). Mobile pedestals is placed below table top. Mobile pedestals made of 18mm thick Pre laminated Particle board. The sides of drawers and facia made of 18mm thick pre laminated Particle Board. Back of the pedestal made of 9mm Pre laminated Particle Board. Pedestal stand-alone and not supported to the table top. Pedestals have 3 drawer 2 for personal and 1 for lateral files. Drawers are provided with single extension telescopic ball bearing slide channels. Pedestal is provided with single central locking system, SS handles and four number poly-propylene castors is provided with the pedestal.Side Unit Size-900(W)X450(D)X750(H) mm. Tabletop made of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 0.6mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading. Modesty panel& Side panel made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading.The side shutter and shelves are made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The back is made of 18mm thick Pre Laminated Particle Board. Each unit have lockable double door is fitted with hinges. Each unit have one numbers of adjustable shelves. Skirting is made of 18mm thick Pre Laminated Particle Board. All exposed edges are sealed with 2mm PVC edge beading.
16	Mid Back Chair:The cushioned seat assembly consists of insert moulded polyurethane foam upholstered with foam laminated mesh fabric. the insert moulded foam is assembeled over a load bearing plastic seat cover. The back made up of two piece injection moulded frame. The inner frame is upholstered with mesh fabric and mounted on the main assembly. Size of back (W)-48.5cm, (H)- 62.0cm & size of seat (W)-51.0cm x (D)-52.5cm. Armrest are injection moulded with height adjustable up to 4.5cm in 3 steps and width adjustable up to 20mm. The mechanism of chair have following features:360 degree revolving type, Front pivot Synchro mechanism, Tilt tension adjustment, 3 position tilt limiter with Anti-Shock feature. Spine bracket made of Iron piece connecting back with mechanism. The chair is provided with pneumatic height adjustment which shall have stroke of 10.0 cm. The pedestal made of die-cast polished aluminium. it fitted with 5 nos twin wheel castor. The size of the pedestal 62.0 cm pitch-centre-dia (70.0 cm with castors). The twin wheel castors are injection moulded in black nylon.
17	Providing and fixing of Workstation System (6 Seating) : One seater overall size-1200(L) 600 (D) Height of panel 1200 mm. Side panel and main panel shall be of 60mm. The 60mm panel comprises of 2 nos. Of vertical trims made of aluminum extrusions and Horizontal trims shall be made of aluminum extrusions at every division of tile/block. Block for 60mm panel’s thickness shall comprises of 38mm thick paper honeycomb + 9mm particle board on each sides + 0.6mm decorative laminate or fabric on both sides. The fabric shall be upholstered with particle board framing shall used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. Blocks shall be located in the mid segment of the panels and shall be provided with cut outs for mounting switch boxes (above the worktops). Fabricated bottom frame for 60mm panel comprises of L channels made of 2mm thick CRCA steel formed plates of 3mm thick HR steel & ERW steel tube of size 35x15x1.6mm thick in oval cross section welded together. This frame shall be bolted to the uprights with M6 screws. Top tiles shall be slid in to the panels from top before fixing the top horizontal. The top shall have white board / glass/ laminate tiles of approved shade. Laminated tiles shall be 9.0 mm thick pre-laminated particle board having all its edges with minimum 0.5 mm thick PVC edge banding. White board tiles shall be made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm thick PVC edge banding. Glass tiles - 4 mm thick toughened clear glass. Split Top shall be provided for two different finishes in single panels. Bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon and support clips made from PP co polymer. Bottom tiles shall be of Metal tiles made of 0.8mm thick CRC sheet. These uprights and horizontals are made of aluminum extrusion having material & have average wall thickness of 1 mm. The panels shall be joined to each other directly with joinery or with the help of post to form. Free standing modules shall be provided with stability bracket. The top trims and end trims for 60 mm shall be made from aluminum extrusion having material. All kinds of extrusions for 60 mm shall have average wall thickness of 1 mm. Top trim shall be press fitted on the horizontal extrusion. Die cast. aluminum alloy shall be provided according to the joineries. The worktop is made of 25mm thick pre laminated particle board with 2mm thick PVC edges bands all around all the edges are pressed with 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The work surface shall be provided with circular cut out of Dia.65mm for passing of wires. These cut outs shall be provided with ABS covers. Table top height – 750mm (including table top thickness of 25mm) Work surface bracket shall be mounted on to the Horizontal extrusion. 4 numbers of ribs are provided in the work surface for strengthening purpose. All the work surface shall be mounted on the work surface through round Philip head diameter 4 mm x 19 length having finish zinc plated. The panel legs shall provide to support panels. Panel legs shall fabricated by CO2 welding MS Tube of section 38 mm x 25 mm ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm over which an M8 Leveler is fitted, which allows for adjustment of the height by 25mm. Double and single side leg assembly: shall be provided to supporting panels & work surface. Wire carrier shall be made from 0.8 mm thick CRCA sheet. It shall be constructed with two parts, one shall be body & another shall be cover. It holds the cables & gives aesthetic appearance by covering all cables. Worktop supporting pedestal shall be provided having provision to fit with worktop and pedestal leg welded assembly fitted at the bottom. The pedestal unit shall be welded assembled with 0.6mm thick CRCA steel for body shell & drawer tray, 1.2 mm thick CRCA top and bottom stiffeners and 0.8mm thick CRCA rear side stiffeners. Drawers shall be provided with double extension precision ball slide with 10 lever Cam lock and centre locking arrangement. Handle. Easy to grip Full length Handle recess integrated into Metal drawer fronts. Construction - Pedestal leg assembly shall be fabricated by CO2 welding vertical MS Tubes of section 38 mm x 25 mm (38 mm x 25 mm x 16bg) inside which leveller holder plates of size 35x22x5mm are welded with horizontal bottom channel made of 2.0 mm thick CRCA sheet. Dimensions Pedestal height is 600 mm without leg assembly and 700 mm including leg assembly. Width of the pedestal shall be 400mm and depth shall be 450mm. Key board tray made of 1.2mm thick CRCA steel. Adjustable wheel mounted CPU trolley made of 1 mm thick CRCA steel. Pedestal, key board tray & CPU Trolley shall be provided with each workstation. . All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
18	Peacock Chair: Chair with low back support chair, chair base made out with wooden finish and chair seat and back structure duly made with medium density foam covered with fabric tapestry two nos. arm made with wooden finish
19	Table: Main table Size-1500(W)X750(D)X750(H) mm. Top made up of 25 mm thick pre laminate MDF board - edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. The Modesty &Side panels made of 0.8 mm thick CRCA sheet with perforation on the sheet shall be uniform of 3mm dimension except 100mm four side border. Leg of the table made up of 50mm round CRCA steel pipe with 1.2m thickness. The three drawer unit size 674(H)x390(W)x440(D) shall be welded assembled with 0.6mm thick CRCA steel for body shell & drawer tray, 1.2 mm thick CRCA top and bottom stiffeners and 0.8mm thick CRCA rear side stiffeners. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
20	Desk & Bench (Three Seater): Desk Frame Size: 1800(L) x 400(D) x 750(H)mm. The Complete MS section to be powder coated in approved based high glosscolour& shade. Vertical supporting pipe is to be made of 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. Front of the seat, perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. The front row have full MS modesty panel. 25x3mm MS angle shall be used for top supporting which shall be connected one part with the table top and another from modesty border pipe. All steel structural components shall be processed and made from virgin material. Seat Frame Size: 1800(L) x 400(D) x 450(H) mm. Seat frame shall be made from Vertical supporting pipe is to be 80x30 mm elliptical shape pipe with 2.0 mm wall thickness to be connected with 50x50x1.6mm horizontal supporting pipe and 1.2mm thick modesty. Seat frame have perforated curved modesty with both side of vertical pipes. 20x20x1.6mm square pipe to be used for strengthening the border of modesty. Seat frame mounting pedestal to be used like a desk frame. Seat shall be mounted on 25.0mm dia. & 1.6mm thick pipe. All steel structural components shall be processed and made from virgin material. DESK TOP& SEAT :Desk Top & Seat made up of 25 mm thick pre laminate particle board - edge duly sealed with 2mm thick PVC Beading. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function .BASKET : Basket shall be Made of 6mm thick Mild steel rod making a curved basket connected with the 50x50 mm square pipe support. FIXING: Fixing at site to be done with metal dash fasteners of 100x12 mm size grouted with chemical filter compound .Pedestal made of 2mm thick pressed HR steel base and shall be ribbed with 2 counters sunk holes for floor fixing. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
21	Steel 3 SeaterChair: 3 Seater Chair public places seating Chair of mild steel with arm. Material of main frame and Sheet and backrest - mild steel. Legs and Armrests are made of aluminum die cast and are Powder Coated for long life. Overall Size: Length -1760mm x depth 520mm x 775mm height. Colour of powder coting- silver. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
22	Mid Back Chair: seat & back made of 12mm thick hot pressed plywood, with fabric and moulded polyurethane foam. The back foam is designed with contoured lumber support for extra comfort. Back foam size 500(W) x490(H) mm. seat foam size 500(W)x 465(D) mm. The seat cover shall be injection moulded in black co- polymer polypropylene and back cover is vacuum formed from ABS sheets. The one piece armrest made of black integral skin polyurethane reinforced with M.S. insert. The armrests are scratch and weather resistant. The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 0.6cm thick HR steel. The center tilt mechanism shall be designed as-360° revolving type, 17° ±2° maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. The pneumatic height adjustment shall have an adjustment stroke of 12.0 ±0.3cm. The Telescopic bellow assy:- The bellow is 3 piece telescopic type and injection molded in black polypropylene .The pedestal is injection molded in black 30% glass filled Nylon. A 10.5 dia forged bright zine plated M.S. caster pin shall be press-fitted into each prong for holding the castors. The pedestal shall be 700 mm pitch-centre-dia. (750 mm with castors).The twin wheel casters are made of nylon. Overall Dimensions of Chair as measured from pedestal - Width-75. cm and Depth-75.0cm. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
23	Dining Table With Chair (6 Seater): Table of size: 1800(L) x 900(W) x 750(H) mm. Top surface of the table shall made up of 25mm thick Sheesham Wood and finished with melamine polish. Top shall be provided with 10mm thick clear toughened Glass with four SS Studs. The table supportLeg to be made of teak wood of size - 75x75 mm and supported with teak wood of size- 75x25mm. Chair of size: 450Wx480Dx900Hmm made of teak wood. Seat foam 50mm thick density of 40kg/m3 pasted on 12mm thick ply covered with good qualityof fabric.The entire dining table & Chair is to be finish by three coats of melamine polish on wood surface for smooth and protective finish.
24	Table: Main table Size-1800(W)X900(D)X750(H) mm. Top and side panel made up of 25 mm thick plain particle board clad with 0.6 mm thick post formed laminate and 06mm thick Backing Laminate.-Flat edge duly sealed with 2mm thick PVC Beading . All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function .Understructure of the table made up of 40x40mm SQR MS pipe with 1.2m thickness. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.
25	Conference Table: Size:7200(L) x 3000(W) x 750(H) mm. With Wire Manager. The top shall be 37 mm thick (18 mm mdf + 18 mm mdf + 0.6 mm laminate + 0.4 mm Membrane ) Edge Profile shall be waterfall edge 10 mm radius on top edge and 5 mm at bottom. In Understructure the Legs shall be made from 25 mm plain MDF having a straight profile with half round edges and with 0.6 mm thick post Forming laminate . Overall thickness of leg shall be 26.2 mm .The modesty panel in understructure shall be made from pre-laminated MDF boards of 18 mm thick with 2mm thick PVC edge beading on all sides. All the PVC edge beading should have press through 200 ° Temperature hot melt glue by automatic through feed edge banding machine with corner rounding function. There shall be Wire Management wire carrier shall be made from 0.6 mm thick CRCA powder coated and carrier cover shall be made of 12 mm thick MDF painted all over. All the metal parts have free from the dent, burrs and sharp edges, rust, scale and any other foreign element before Powder coating. The minimum thickness of powder coated should be 40-50 microns.