Commissioning Of Wss Aragam By Way Of Providing And Laying Of Gi Pipe Const Of Chowkidar Quarter Pump House Cement Concrete R Wall Etc Commissioning Of Wss Aragam By Way Of Providing And Laying Of Gi Pipe Const Of Chowkidar Quarter Pump House Cement Concr
Tender Value
11.27 Crore
Estimated cost
Bid Submission
02 Dec 2021
0 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bandipore → Jammu And Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Commissioning Of Wss Aragam By Way Of Providing And Laying Of Gi Pipe Const Of Chowkidar Quarter Pump House Cement Concrete R Wall Etc Commissioning Of Wss Aragam By Way Of Providing And Laying Of Gi Pipe Const Of Chowkidar Quarter Pump House Cement Concrete R Wall Etc
BOQ
| Sl. No. | Item Description |
| 1 | Providing, fitting and commissioning of Single Phase Submersible type Pumping Unit along with allied Jobs. Complete details of the Job are as underP/F/T and commissioning of single phase pumping equipment with following specifications:Discharge = 3000-4000 LPHHead= 80- 110 mtrs.Speed= 2800- 2900 rpmMake=ReputedmakeMotor Rating = As per corresponding head and dischargeThe pump motor is to be coupled together with a steel coupling. The job includes lowering of the submersible pump equipment.It includes P/F of DOL Starter(One pumping motor will be as stand by pumping unit) |
| 2 | Providing and fitting of 32 mm Dia GI Column pipe (Heavy duty). Pipe is to be properly threaded at both the ends and the length of each pipe should not exceed 3 Mts. The pipe is provided and fitted with GI Sockets for jointing purpose. |
| 3 | P/F of 10 KVA single phase Manually operatedvoltage stabilizers, oil cooledworking on single phase input voltage from 70 volt to 220 volt |
| 4 | P/F of submersible cable 4 sq. mm, L&T/Havel’s make, connecting pumping unit with starter |
| 5 | P/F of 5mm steel wire rope for holding sub type pumping unit. |
| 6 | P/F of 63 Amps D.P switch with 3 pin top.Make L&T/ Havel’s. Job includes Providing and fixing of 3 ft X 3 ft Bakelite sheet of wall with necessary arrangements. |
| 7 | P/F of 40 mm dia. MS holding clamps fabricated out of 10 mm thick MS Plate with nuts and bolts |
| 8 | Providing /Fitting Of Flowing Pipe FittingsApproximately1)1.5 X1 Inch Dia GIReducers04 No’s2) 1 Inch Dia GI Bends 10 No’s3)1 Inch Dia GI Sockets20 No’s 4) ¾ 20 Mm Dia GI Sockets15 No 05¾ 20 mm Dia GI bends 07 No |
| 9 | Providing /testing of chain pulley block 01 MT capacityheavy duty Indian make along with 10 meter double chain |
| 10 | Fabrication ,providing ,and testing of tripod stand fabricated out ofC class 4 inch Dia GI pipe having length of each pipe 8rft with heavy duty clubbing arrangement |
| 11 | providinf and fixing of 7/20 mm service line |
| 12 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth asdirected: All kinds of soil |
| 13 | Ordinary Rock |
| 14 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil |
| 15 | Ordinary or hard rock |
| 16 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: |
| 17 | Ordinary or hard rock |
| 18 | Extra for every additional lift of 1.5 m or part thereof in excavation/banking excavated or stacked material : All kinds of soil : |
| 19 | Laying and fitting of G.I. pipes (all classes) complete excluding cost of pipes, fittings and Earth work:- 50mm dia G.I pipe |
| 20 | 40mm dia G.I pipe |
| 21 | 25mm dia G.I pipe |
| 22 | 20mm dia G.I pipe |
| 23 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/by mechanical means including stacking of pipes within 50 meters lead as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore |
| 24 | Above 40 mm nominal bore |
| 25 | ProvidingG.I. pipes complete with G.I. fittings Mediumweight classB excluding trenching and refilling etc. (external work) :-100mm dia G.I pipe |
| 26 | Providing and fixing G.I. pipes complete with G.I. fittings light weight class A excluding trenching and refilling etc. (external work) :-50mm dia G.I pipe |
| 27 | 40mm dia G.I pipe |
| 28 | 25mm dia G.I pipe |
| 29 | 20mm dia G.I pipe |
| 30 | 15mm dia G.I pipe |
| 31 | Providing and fixing of 14 mm thick M.S flangesG.I pipe incld. Cost of flanges, rubber gaskets, nuts bolts, welding charges cutting of threads excld. Earth work and refilling: 100mm dia |
| 32 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions incld. Tailpeices ,tapers, Gi pipeetc. complete 25mm dia |
| 33 | Providing and fixing of CI sluice valve with cap including all accessories like nuts, bolts rubber insertion etc and tail pieces of Kirloskar make including successful testing and commissioning. 150 mm dia |
| 34 | 100mm dia |
| 35 | 80mm dia |
| 36 | Making connection of G.I. distribution branch with G.I. main offollowing sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete 25 to 40 mm nominal bore |
| 37 | 50 to 80 mm nominal bore |
| 38 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 50 mm nominal bore |
| 39 | Constructing masonry Chamber of specified size, in brick work with common burnt clay (non modular) bricks of class designation 7.5 incement mortar 1:4 (1cement :4 coarse sand) and R.C.C. top slab 1:1.5:3mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mmnominal size ) including necessary xcavation, foundation concrete1:5:10 (1 cement :5 fine sand : 10 graded stone aggregate 40 mmnominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.For sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid.Chamber 120x120x100 cm |
| 40 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating eachdeposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m |
| 41 | Providing & laying stone soling in horizontal on level. |
| 42 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 43 | Dry random rubble masonry with hard stone in foundation and plinth: With bond stone. |
| 44 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size) |
| 45 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 46 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with : 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 47 | Providing & fixing of main hole cover 0.75 x 0.75 of standard quality with angle iron frame incld all necessary fittings complete |
| 48 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level: Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 49 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all completeWelded |
| 50 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete |
| 51 | Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete. |
| 52 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 53 | Suspended floors, roofs, landings, balconies and access platforms |
| 54 | Lintel, beams, plinth beams, girders, bressumers and cantilevers |
| 55 | Edges of slabs and breaks in floors and walls : Under 20 cm wide |
| 56 | Columns, pillars, piers, abutments, posts and struts. |
| 57 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 58 | 12mm Cement plaster finished with a floating coat of neat cement of mix:1:3 (1 cement 3 sand) |
| 59 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-incharge. Made of G.I. wire of dia 4 mm |
| 60 | 12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) |
| 61 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 62 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness)including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses,string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills,fillets etc upto floor V level, including curing but excluding the cost of centring, shutteringand finishing with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 63 | Providing & laying damp-proofCourse 40 mm thickwith cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete |
| 64 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 65 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 66 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 gradedstone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate |
| 67 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and lengthhold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood |
| 68 | Providing and fixingglazed shutters for , windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). First class kail wood (35mm) |
| 69 | Providing and fixing of 4mm thick Float glass panes(weighing not less than 10 kg/sqm |
| 70 | Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S Flat 15x3 mm and nuts and bolts complete.Galvanized M.S wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 71 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1and M.S. top cover of required thickness for rolling shutters. 80x0.90 mm M.S. laths with 0.90 mm thick top cover |
| 72 | Providing and fixing of panneled 40mm thick doors of of first class kail wood incld all sorts of carraige complete |
| 73 | Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gram/m2 |
| 74 | Providing & fixing colour corrigated ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gram/m2 |
| 75 | Providing and fixing plained eaves boarding (Kail wood). 250x32 mm (nominal size ) |
| 76 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (2 mm thick ) |
| 77 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 78 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shadeTwo or more coats on new work |
| 79 | Providing & fixing White vitreous china water closet squatting pan(Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in chargeLong pattern W.C Pan of size 580x440 mm |
| 80 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including all associatedfittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license] |
| 81 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (wall / floor tiles) |
| 82 | Providing and fixingin position stainless steel sink of standard quality |
| 83 | Applying priming coat:- With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel work (second coat) |
| 84 | Painting with aluminum paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 85 | P/F waste pipe for sink incld pvc waste filling complete 40mm dia |
| 86 | Providing and fixing of iron clamps incldnuts bolts , incld one end fix to anchor block |
| 87 | Welding, including transportation of plant at site etc. complete By electric plant |
| 88 | Providing and fitting of bedroom items Floor mating, 01 No. beds with necessary beding and mattresses , 01 no. wardrobes for cloths, 1 no. locker, 4 chairs and one table, Utensilsgas with gas stove etc |
| 89 | provision for plumbing , sanitary, electrification , 1 No. water Gysers, 2 No. water mixers. 4 No. Bibcock s, Mirrors, Jugs/ mugs & other bathroom accessories etc |
| 90 | Provision for Providing and fixing of pipe specials of standard quality incld. testing complete |
| 91 | Carraige of materials from source to road site of work including loading , unloading and stacking:-- Stone / stone soling for an av lead of 15 km |
| 92 | 40mm aggregate for an av lead of 45 km |
| 93 | 20mm aggregate for an av lead of 45 km |
| 94 | sand for an av lead of 40 km |
| 95 | cement/s for an steeteelav lead of 8 km |
| 96 | Bricks for an av lead of 70 km |
| 97 | Earth for an av lead of 5 km |
| 98 | Carraige of materials fromroad siteto site of work by manual labour including loading , unloading and stacking for an av lead of 100 Mtrs. Stone / stone soling |
| 99 | 40mm aggregate |
| 100 | 20mm aggregate |
| 101 | sand |
| 102 | Cement / steel |
| 103 | Bricks |
AI Tender Summary
Tender Timeline
Nov 18, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedDec 02, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 04, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender