Indian Army-IA has published Bids Are Invited For Lightening Conductor - Lightening Conductor. Supply Of Jelly Filled Lightening Conductor As Per Specification Mentioned Below:- (I) Earthing Electrode. Prefabricated Get Earthing Electrode Of Pipe In Pipe Tehnology. Two B Class Is Mil. Submission Date for this Tender is 22-11-2021. Bath and Body Tenders in Jammu And Kashmir. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Title | Item Description |
| 1 | Lightening Conductor | Lightening conductor. Supply of jelly filled lightening conductor as per specification mentioned below:- (i) Earthing Electrode. Prefabricated get earthing electrode of pipe in pipe tehnology. Two B class IS mild steel pipes, one side the other, hot dip galvanised with 100 micron coating outside and about 300 micron coating inside, filled with high conductor and corrosion resistant crystaline mixture and back fill compound around electrode as per IS 3043/1987. (ii)Anchorage.GI wire 12 gauge ties to vertical post and anchorage to the ground using iron spikes.Slope of wire 1:2.There will be three anchors ISI marked. (iii) Earth work - Excavation shall be carried out rocky soil for earthing pit of size 0.25m x 0.25m x 2.0m depth incl removal of surplus soil in low laying area. (iv) Down Conductors.Aluminum strip size 25mm x 3mm of length 9m ISI marked. (v)Earthing Strip.GI strip 32mm x 6mm of length 3m. Qty Nos 01 each ISI marked. (vi) Vertical post. GI pipe dia 40mm of length 6m embeded in foundation concrete block of size 0.45 x0.45 x0.75m ISI marked. (vii) Air Terminal.GI nipple 15mm dia and 10cm length one copper ball having 05 Nos copper prong of 15cm length.Prongs and nipple fitted to copper ball with threading arrangements. |
| 2 | Heating Device | Heating Device (Kerosene Based). Two numbers Heating device of following specifications will be provided with each shelter Make : Paseco PSG-22G/Kero Heat CV-2230/ Toyotomi. Each heating device shall be supported with 01 additional wick. |
| 3 | Steel Roofing Trough | Steel Roofing Trough (SRT) of size 1630mm x 613mm x 180mm made out of 2mm thick hot rolled carbon steel sheet conforming to IS 5986 EE-330 complete with setand a spanner OJDE of size 20-22 per 10 Nos of SRT. SRTs shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer. Sample to be approved before supply. |
| 4 | Fence New Design 1 | Supply offoldable Weld Mesh Panels as per below spec. Mesh Wire :Horizontal wire, Dia 5.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.5 mm (+/-0.05mm)Mesh Size: Mesh Size of 50 x 100 mm - V Bend &50X200 mm (+/- 2 mm) along Mesh ( Mesh Wire: IS 280 2006). Panel size &Weight :2600X800 11.3 Kg with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place. Coating : Zinc coated 40-50GSM &60 to 80 microns of Powder coating. Color:RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength:Min 550 N/Sq.mm. Weld tensile strength:Min 70% of Wire tensile strength. Note: Weldmesh is installed vertically above the High Security Weldmesh Ref Drawing No :NC/LC/A8/V2.2. Material: MS Mesh Wire: Dia:4mm: IS 280 2006 Coating :IS 4826 – 1979 Weld Mesh as per : EN 10223-7 |
| 5 | Fence New Design 2 | Alpha Fence Supply of High SecurityFoldableWeld Mesh Panels as per below spec.Mesh Wire : Horizontal wire, Dia 4.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.0 mm (+/-0.05mm) Mesh Size: Mesh Size of 12.7 X 76.2 mm along Mesh ( Mesh Wire: IS 280 2006). Panel size &Weight : 2600X800mm: 22.52 Kg with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place.Coating : Zinc coated 40-50GSM &60 to 80 microns of Powder coating Color: RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength: Min 550 N/Sq.mm. Weld tensile strength: Min 70 % of Wire tensile strength. Note: High Security Weld mesh is been installed at the bottom.. Ref Drawing No :NC/LC/A8/V2.2. Material: MS Mesh Wire: Dia: 4mm: IS 280 2006 Coating :IS 4826 – 1979 Weld Mesh as per : EN 10223-7 |
| 6 | Fence New Design 3 | (Bravo Fence) Weld Mesh Panels: Mesh Wire : Horizontal wire, Dia 5.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.5 mm (+/-0.05mm)Mesh Size : Mesh Size of 50 x 100 mm - V Bend &50X200 mm (+/- 2 mm) along Mesh as per dwg.( Mesh Wire: IS 280 2006). Panel size (W &H) &Weight ( Tol +/-5%)2600X1000mm : 13.02 Kg, with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place.Surface of weld mesh panel must be absolutely plain without any intrinsic crests. Coating :Zinc coated 40-50 GSM&60 to 80 microns of Powder coating Color: RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength: Min 550 N/Sq.mm. Weld tensile strength: Min 70 % of Wire tensile strength. Ref Drawing No : NC/LC/A8/V2.2. Mesh Wire: IS 280 2006 Coating :IS 4826 – 1979 Material: MS Material Weld Mesh as per : EN 10223-7 |
| 7 | Fence New Design 4 | Punched Tape Baby Concertina Coil (including spike and handle) with 50 turns and dia 610 mm, having a core wire of high carbon spring steel of high tensile strength. The punched tape and core wire (2.6 ± 0.035 mm dia) are electro galvanised to provide protection against outdoor exposure. The punched tape is mechanically crimped over the core wire and then formed into a coil at various parts of the periphery of the coil; steel clips “total 70 Nos per coil equally spaced” to connect the individual turns of the coil to each other so that it opens up like an accordion. The width of strip as 19 mm and spacing of blades 24.00 ± 0.5 mm C/C. The weight of each coil will be 8 ± 5% Kgs without packing material and coil length 6-8 mtr when opened up with an effective height of 475 mm. Each coil wound with bituminised Hessian cloth for providing protective packing. (143 coils per Km).23 |
| 8 | Fence New Design 5 | Punched Tape Concertina Coil : 850 mm Dia / 18 loops / 3.5 mm core wire.Coil Diameter : 850 mm (+/- 50mm). Blade Profile : Tear Blade Profile. Core Wire : High Tensile, 3.5 mm (+/-0.1mm) Dia. Zinc coating : Galvanised to min : 275 GSM. Tensile Strength of Wire: 1400 – 1500 N/sq.mm. Number of loops: 18. Stretchable length: 2.5 mtrs. Locking Clips: 5 clips per set of loops. Weight: 6.7 Kgs (+/-5%). Ref Drawing No :NC/LC/A2/V2.2. Specn for Steel Strip: IS 1730 Specn for wire: IS 280 2006 Specification for coating : Min 275 GSM Zinc coating as per IS 6745 / 1972 reaffirmed 2006 PTCC shall confirm to CQA, EE, Pune specification No : CQAE / 5660/1602/A and controllerate of quality assurance of Engg. Equipment, PUNE Drawing No IMGA-0112/B ( Sheet 1 to 2) , IMGA- 0112/ C(Sheet 2 to 2), IMPD – 1817/B, IMPD – 1820, IMPD – 1821/B and IMPD -1822/B . |
| 9 | Fence New Design 6 | Fence Post : Type : Circular Telescopic Hollow section, dimensions outer pole dia 2.7" inner pole dia 2.2" along with mushroom bolt of size 18 mm x 120 mm .Dimensions : 2.7 inch,Dia, 3 mm (3mm +/- 0.3mm) Thickness: inner pole dia 2.2 inch along with two mushroom bolt and nutsize 18mm x 120 mmAll tolerances as per IS specnIS: 1239 Length : 3.4 mtrs B 2.7 mtrs above ground level + 0.7 mtrs under the ground level). Weight: 21.6 Kg (+/-5 %) Coating : Hot Dip glvanised to minimum 350 GSM Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123Ref Drawing No :NC/LC/A6/V2.2. Fence Post- IS: 1239 Material: MS Steel Tube |
| 10 | Fence New Design 7 | (I) Truss support Post with Rail end Cap : Type : Circular Hollow section. Dimensions :76mm Dia, 3 mm (3mm +/- 0.3mm).Rail End Cap Fitting -76 mm (Rail End Cap is fitted to Truss Support using M8X100 Nut and Bolt Mechanism).Thickness: All tolerances as per IS specnIS:1239. Length &Weight. 1. Truss support for across the slope condition. Length :1800mm, Weight : 9.65 Kg(+5%). Coating : Hot Dip galvanised to minimum 350 GSM. Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123. |
| 11 | Fence New Design 8 | (II) Truss support Post with Rail end Cap : Type : Circular Hollow section. Dimensions :76mm Dia, 3 mm (3mm +/- 0.3mm).Rail End Cap Fitting -76 mm (Rail End Cap is fitted to Truss Support using M8X100 Nut and Bolt Mechanism).Thickness: All tolerances as per IS specnIS:1239. Length &Weight. 1. Truss support for along the slope condition. Length:3100mm, Weight : 16.6 Kg(+5%).. Coating : Hot Dip galvanised to minimum 350 GSM. Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123. Ref Drawing No:NC/LC/A1/V2.2.Fence Post- IS: 1239. Coating - as per IS 2629 / IS 4759 /ASTM A 123. Material: MS Steel Tube Tangdhar Nos640 |
| 12 | Fence New Design 9 | Straining Y-Arm for supporting top PTCC: Material : CHS of Dia 60 mm Length 100mmand 3.2mm guage as per IS 1852. Coating : Hot dip galvanized to Min 350 GSM as per IS 4759/2629, Length of 1 Arm is 510 mm,outer dia of 50 mm of sleeve cap will be fitted on the top of the fence post and fixed with two Nos mushroom head bolt andnut (M8x25mm). Straining Y-Arm will manufactured as per drawing attached. Straining Y Arm will be installed at every 10 mtrs except intermediate arm post. |
| 13 | Fence New Design 10 | Intermediate Y-Arm for supporting top PTCC: Material: CHS of Dia 50 mm Length 100mm and 2.90mm guage as per IS1852 Coating :Hot dip galvanized to Min 350 GSM as per IS 4759 / IS 2629.Length of 1 Arm is510 MM , Angle between the two arms is 120 degree , fixed with two Nos mushroom head bolt andnut (M8x25mm).Intermediate Y-Arm will manufactured as per drawing attached. Outer dia of 76 mm of sleeve cap will be fitted on the top of the fence post. One Intermediate YArm will be installed at every post except the posts with Straining Y arms |
| 14 | Fence New Design 11 | Razor Running Tape Blade profile : Tear Blade Corewire : 2.5 mm wire Dia +0.1mm, Length of each Coil : 95 Mtrs Weight of each coil : 9.2 Kg.Ref Drawing No : NC/LC/A2/V2.2. Specn for Steel Strip: IS 1730 Specn for wire: IS 280 2006 |
| 15 | Fence New Design 12 | I. Accessories for fitting panel :-Omega Clamp - 89 mm Dia, 35mm Width, 3mm Thick Flat - 35mm Width, 5mm Thickmaterial MSwith hot dip galvanized to 350 GSM.(6 Nos per post) |
| 16 | Fence New Design 13 | (a) Mushroom Head bolt with breakable headsafety nut (12 per post) - M8X50, SS material. Ref Drawing No : NC/LC/A6/V2.2 (For A10). Material Ms Strip as per 1730. IS : 8535 -1987. Material :SS 304 |
| 17 | Fence New Design 14 | II. Accessories for fitting Truss Support Post:- (a) Brace Band-89 mm 41mm Width, 4mm Thick material MSwith hot dip galvanized to 350 GSM.(1 No per Alpha post). |
| 18 | Fence New Design 15 | III. Accessories for fitting Y Arm :- (a). Mushroom Head Bolt with breakable head safety nut (M8X120) (2No per post): Material : SS 304 |
| 19 | Fence New Design 16 | (b) Eye Bolt with Loop nut M8X100, Material SS. There will be 6 eye bolts for each straining Y Arm. There are 34 straining Y Arm per KM. So 204 eye bolts are required for per KM.. Material :SS. Material Ms Strip as per 1730. IS : 8535 -1987. |
| 20 | Fence New Design 17 | IV. Underground post fixing arrangement:- (a)Anchor Rod 10mm Dia 300mm long GI Rod tie with fence post at bottom using tie wire.(2 Nos per post). Holes of suitable dimention will be provided at lower end of fence post to insert the anchor rod into it. |
| 21 | Fence New Design 18 | (b) Tie Wire – 1.4mm dia/ 100mm length. Wire : IS 280 2006MS Material (02 Nos per Anchor rod) |
| 22 | Fence New Design 19 | V (a) Flat clamps for panel connection Flat 25x3, 160mm long, 2-slots |
| 23 | Fence New Design 20 | (b) SS 304 Mushroom head bolt, M8X25 Sheet Metal IS 1730. IS : 8535 -1987. Material :SS 304 |
| 24 | Fence New Design 21 | VI. Hog ring, As per drawing. To secure PTC coil to PTC coil and also PTC coil to panels. Wire Dia : 3mm : shape and size as per drawing No NC/LC/A6/V2.2 dt 06 Nov 15. |
| 25 | Fence New Design 22 | Punched Tape Concertina coil: 1050 mm Dia /18 loops/ 3.5 mm core wire. Coil Diameter: 1050 mm (+/- 50mm). Blade Profile : Tear Blade profile. Core wire: High Tensile , 3.5 mm (+/- 0.1mm) Dia. Zinc coating :Galvanised to min: 275 GSM.Tensile strength of wire :1400 – 1500 N/sq.mm. Number of loops :18. Stretchable length : 2.5 mtrs.Locking clips :7 clips per set of two loops. Weight : 8.2 Kg (+/-5%). Ref Drawing No : NC/LC/A3/V2.2. Specn for Steel Strip: IS 1730. Specn for wire: IS 280 2006 PTCC shall confirm to CQA, EE, Pune specification No : CQAE / 5660/1602/A and controllerate of quality assurance of Engg. Equipment, PUNE Drawing No IMGA-0112/B ( Sheet 1 to 2) , IMGA- 0112/ C(Sheet 2 to 2), IMPD – 1817/B, IMPD – 1820, IMPD – 1821/B and IMPD -1822/B . |
| 26 | Fence New Design 23 | Fence Post : Type : Circular Hollow section Dimensions : outer dia pole 2.7". Inner pole dia 2.2" alongwith mushroom boltof size 8mm x 120mm, 3 mm (3mm +/- 0.3mm) thickness: All tolerances as per IS specnIS:1239 Length : 2.8mtrs (2.1 mtrs above ground level + 0.7 mtrs under the ground level). Weight : 15.02 Kg (+/-5%) Coating :Hot Dip galvanised to minimum 350 GSM Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123.Ref Drawing No : NC/LC/A1/V2.2. Fence Post- IS: 1239. Coating - as per IS 2629 / IS 4759 /ASTM A 123 Material: MS Steel Tube |
| 27 | Fence New Design 24 | I. Across Fence Post :- Clamp - 76 mm Dia, 35mm Width, 3mm Thick material MSwith hot dip galvanized to 350 GSM(2 Set per post). |
| 28 | Fence New Design 25 | (a) Mushroom Head bolt with breakable head nut M8X50 (4 per post) : material :SS Ref Drawing No :NC/LC/A6/V2.2. Material: MS strip as per IS 1730. IS : 8535 -1987. Material :SS 304 |
| 29 | Fence New Design 26 | II. Underground post fixing arrangement (a) Anchor Rod 10mm Dia 300 mm long GI Rod tie with fence post at bottom using tie wire.(2 Nos per post). |
| 30 | Fence New Design 27 | (b) Tie Wire – 1.4mm dia/ 100mm length. Wire : IS 280 2006MS Material (02 Nos per Anchor rod) Ref Drawing No :NC/LC/A6/V2.2. IS 280 2006.MS Material. MS Tie Wire:IS 280 2006 |
| 31 | Fence New Design 28 | III. PTCC Rod 12 mm dia 2.64 mm long MS Rod. Suitable arrangement be made on fence postfor holding of PTCC rod. Material MSwith hot dip galvanized to 350 GSM |
| 32 | Fence New Design 29 | IV. Post Cap. Ref Drawing No :NC/LC/A10/V2.2 IS: 1239. Material: MS |
| 33 | Fence New Design 30 | V.(a) Brace Band-76 mm 41mm Width, 4mm Thick material MSwith hot dip galvanized to 350 GSM(1 No per Bravo post) |
| 34 | Fence New Design 31 | (b) Mushroom Head bolt with breakable headsafety nut - M8X50, Material : SS Ref Drawing No :NC/LC/A6/V2.2. Material Ms Strip as per 1730.IS : 8535 -1987. Material :SS 304. |
| 35 | Fence New Design 32 | Hog ring, As per drawing. To secure PTC coil to PTC coil and also PTC coil to panels. Wire Dia : 3mm : shape and size as per drawing No NC/LC/A6/V2.2 dt 06 Nov 15. |
| 36 | Fence New Design 33 | Supply offoldable Weld Mesh Panels as per below spec. Mesh Wire :Horizontal wire, Dia 5.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.5 mm (+/-0.05mm)Mesh Size: Mesh Size of 50 x 100 mm - V Bend &50X200 mm (+/- 2 mm) along Mesh ( Mesh Wire: IS 280 2006). Panel size &Weight :2600X800 11.3 Kg with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place. Coating : Zinc coated 40-50GSM &60 to 80 microns of Powder coating. Color:RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength:Min 550 N/Sq.mm. Weld tensile strength:Min 70% of Wire tensile strength. Note: Weldmesh is installed vertically above the High Security Weldmesh Ref Drawing No :NC/LC/A8/V2.2. Material: MS Mesh Wire: Dia:4mm: IS 280 2006 Coating :IS 4826 – 1979 Weld Mesh as per : EN 10223-7 |
| 37 | Fence New Design 34 | Alpha Fence Supply of High SecurityFoldableWeld Mesh Panels as per below spec.Mesh Wire : Horizontal wire, Dia 4.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.0 mm (+/-0.05mm) Mesh Size: Mesh Size of 12.7 X 76.2 mm along Mesh ( Mesh Wire: IS 280 2006). Panel size &Weight : 2600X800mm: 22.52 Kg with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place.Coating : Zinc coated 40-50GSM &60 to 80 microns of Powder coating Color: RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength: Min 550 N/Sq.mm. Weld tensile strength: Min 70 % of Wire tensile strength. Note: High Security Weld mesh is been installed at the bottom.. Ref Drawing No :NC/LC/A8/V2.2. Material: MS Mesh Wire: Dia: 4mm: IS 280 2006 Coating :IS 4826 – 1979 Weld Mesh as per : EN 10223-7 |
| 38 | Fence New Design 35 | (Bravo Fence) Weld Mesh Panels: Mesh Wire : Horizontal wire, Dia 5.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.5 mm (+/-0.05mm)Mesh Size : Mesh Size of 50 x 100 mm - V Bend &50X200 mm (+/- 2 mm) along Mesh as per dwg.( Mesh Wire: IS 280 2006). Panel size (W &H) &Weight ( Tol +/-5%)2600X1000mm : 13.02 Kg, with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place.Surface of weld mesh panel must be absolutely plain without any intrinsic crests. Coating :Zinc coated 40-50 GSM&60 to 80 microns of Powder coating Color: RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength: Min 550 N/Sq.mm. Weld tensile strength: Min 70 % of Wire tensile strength. Ref Drawing No : NC/LC/A8/V2.2. Mesh Wire: IS 280 2006 Coating :IS 4826 – 1979 Material: MS Material Weld Mesh as per : EN 10223-7 |
| 39 | Fence New Design 36 | Punched Tape Baby Concertina Coil (including spike and handle) with 50 turns and dia 610 mm, having a core wire of high carbon spring steel of high tensile strength. The punched tape and core wire (2.6 ± 0.035 mm dia) are electro galvanised to provide protection against outdoor exposure. The punched tape is mechanically crimped over the core wire and then formed into a coil at various parts of the periphery of the coil; steel clips “total 70 Nos per coil equally spaced” to connect the individual turns of the coil to each other so that it opens up like an accordion. The width of strip as 19 mm and spacing of blades 24.00 ± 0.5 mm C/C. The weight of each coil will be 8 ± 5% Kgs without packing material and coil length 6-8 mtr when opened up with an effective height of 475 mm. Each coil wound with bituminised Hessian cloth for providing protective packing. (143 coils per Km).23 |
| 40 | Fence New Design 37 | Punched Tape Concertina Coil : 850 mm Dia / 18 loops / 3.5 mm core wire.Coil Diameter : 850 mm (+/- 50mm). Blade Profile : Tear Blade Profile. Core Wire : High Tensile, 3.5 mm (+/-0.1mm) Dia. Zinc coating : Galvanised to min : 275 GSM. Tensile Strength of Wire: 1400 – 1500 N/sq.mm. Number of loops: 18. Stretchable length: 2.5 mtrs. Locking Clips: 5 clips per set of loops. Weight: 6.7 Kgs (+/-5%). Ref Drawing No :NC/LC/A2/V2.2. Specn for Steel Strip: IS 1730 Specn for wire: IS 280 2006 Specification for coating : Min 275 GSM Zinc coating as per IS 6745 / 1972 reaffirmed 2006 PTCC shall confirm to CQA, EE, Pune specification No : CQAE / 5660/1602/A and controllerate of quality assurance of Engg. Equipment, PUNE Drawing No IMGA-0112/B ( Sheet 1 to 2) , IMGA- 0112/ C(Sheet 2 to 2), IMPD – 1817/B, IMPD – 1820, IMPD – 1821/B and IMPD -1822/B . |
| 41 | Fence New Design 38 | Fence Post : Type : Circular Telescopic Hollow section, dimensions outer pole dia 2.7" inner pole dia 2.2" along with mushroom bolt of size 18 mm x 120 mm .Dimensions : 2.7 inch,Dia, 3 mm (3mm +/- 0.3mm) Thickness: inner pole dia 2.2 inch along with two mushroom bolt and nutsize 18mm x 120 mmAll tolerances as per IS specnIS: 1239 Length : 3.4 mtrs B 2.7 mtrs above ground level + 0.7 mtrs under the ground level). Weight: 21.6 Kg (+/-5 %) Coating : Hot Dip glvanised to minimum 350 GSM Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123Ref Drawing No :NC/LC/A6/V2.2. Fence Post- IS: 1239 Material: MS Steel Tube |
| 42 | Fence New Design 39 | (I) Truss support Post with Rail end Cap : Type : Circular Hollow section. Dimensions :76mm Dia, 3 mm (3mm +/- 0.3mm).Rail End Cap Fitting -76 mm (Rail End Cap is fitted to Truss Support using M8X100 Nut and Bolt Mechanism).Thickness: All tolerances as per IS specnIS:1239. Length &Weight. 1. Truss support for across the slope condition. Length :1800mm, Weight : 9.65 Kg(+5%). Coating : Hot Dip galvanised to minimum 350 GSM. Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123. |
| 43 | Fence New Design 40 | (II) Truss support Post with Rail end Cap : Type : Circular Hollow section. Dimensions :76mm Dia, 3 mm (3mm +/- 0.3mm).Rail End Cap Fitting -76 mm (Rail End Cap is fitted to Truss Support using M8X100 Nut and Bolt Mechanism).Thickness: All tolerances as per IS specnIS:1239. Length &Weight. 1. Truss support for along the slope condition. Length:3100mm, Weight : 16.6 Kg(+5%).. Coating : Hot Dip galvanised to minimum 350 GSM. Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123. Ref Drawing No:NC/LC/A1/V2.2.Fence Post- IS: 1239. Coating - as per IS 2629 / IS 4759 /ASTM A 123. Material: MS Steel Tube Tangdhar Nos640 |
| 44 | Fence New Design 41 | Straining Y-Arm for supporting top PTCC: Material : CHS of Dia 60 mm Length 100mmand 3.2mm guage as per IS 1852. Coating : Hot dip galvanized to Min 350 GSM as per IS 4759/2629, Length of 1 Arm is 510 mm,outer dia of 50 mm of sleeve cap will be fitted on the top of the fence post and fixed with two Nos mushroom head bolt andnut (M8x25mm). Straining Y-Arm will manufactured as per drawing attached. Straining Y Arm will be installed at every 10 mtrs except intermediate arm post. |
| 45 | Fence New Design 42 | Intermediate Y-Arm for supporting top PTCC: Material: CHS of Dia 50 mm Length 100mm and 2.90mm guage as per IS1852 Coating :Hot dip galvanized to Min 350 GSM as per IS 4759 / IS 2629.Length of 1 Arm is510 MM , Angle between the two arms is 120 degree , fixed with two Nos mushroom head bolt andnut (M8x25mm).Intermediate Y-Arm will manufactured as per drawing attached. Outer dia of 76 mm of sleeve cap will be fitted on the top of the fence post. One Intermediate YArm will be installed at every post except the posts with Straining Y arms |
| 46 | Fence New Design 43 | Razor Running Tape Blade profile : Tear Blade Corewire : 2.5 mm wire Dia +0.1mm, Length of each Coil : 95 Mtrs Weight of each coil : 9.2 Kg.Ref Drawing No : NC/LC/A2/V2.2. Specn for Steel Strip: IS 1730 Specn for wire: IS 280 2006 |
| 47 | Fence New Design 44 | I. Accessories for fitting panel :-Omega Clamp - 89 mm Dia, 35mm Width, 3mm Thick Flat - 35mm Width, 5mm Thickmaterial MSwith hot dip galvanized to 350 GSM.(6 Nos per post) |
| 48 | Fence New Design 45 | (a) Mushroom Head bolt with breakable headsafety nut (12 per post) - M8X50, SS material. Ref Drawing No : NC/LC/A6/V2.2 (For A10). Material Ms Strip as per 1730. IS : 8535 -1987. Material :SS 304 |
| 49 | Fence New Design 46 | II. Accessories for fitting Truss Support Post:- (a) Brace Band-89 mm 41mm Width, 4mm Thick material MSwith hot dip galvanized to 350 GSM.(1 No per Alpha post). |
| 50 | Fence New Design 47 | III. Accessories for fitting Y Arm :- (a). Mushroom Head Bolt with breakable head safety nut (M8X120) (2No per post): Material : SS 304 |
| 51 | Fence New Design 48 | (b) Eye Bolt with Loop nut M8X100, Material SS. There will be 6 eye bolts for each straining Y Arm. There are 34 straining Y Arm per KM. So 204 eye bolts are required for per KM.. Material :SS. Material Ms Strip as per 1730. IS : 8535 -1987. |
| 52 | Fence New Design 49 | IV. Underground post fixing arrangement:- (a)Anchor Rod 10mm Dia 300mm long GI Rod tie with fence post at bottom using tie wire.(2 Nos per post). Holes of suitable dimention will be provided at lower end of fence post to insert the anchor rod into it. |
| 53 | Fence New Design 50 | (b) Tie Wire – 1.4mm dia/ 100mm length. Wire : IS 280 2006MS Material (02 Nos per Anchor rod) |
| 54 | Fence New Design 51 | V (a) Flat clamps for panel connection Flat 25x3, 160mm long, 2-slots |
| 55 | Fence New Design 52 | (b) SS 304 Mushroom head bolt, M8X25 Sheet Metal IS 1730. IS : 8535 -1987. Material :SS 304 |
| 56 | Fence New Design 53 | VI. Hog ring, As per drawing. To secure PTC coil to PTC coil and also PTC coil to panels. Wire Dia : 3mm : shape and size as per drawing No NC/LC/A6/V2.2 dt 06 Nov 15. |
| 57 | Fence New Design 54 | Punched Tape Concertina coil: 1050 mm Dia /18 loops/ 3.5 mm core wire. Coil Diameter: 1050 mm (+/- 50mm). Blade Profile : Tear Blade profile. Core wire: High Tensile , 3.5 mm (+/- 0.1mm) Dia. Zinc coating :Galvanised to min: 275 GSM.Tensile strength of wire :1400 – 1500 N/sq.mm. Number of loops :18. Stretchable length : 2.5 mtrs.Locking clips :7 clips per set of two loops. Weight : 8.2 Kg (+/-5%). Ref Drawing No : NC/LC/A3/V2.2. Specn for Steel Strip: IS 1730. Specn for wire: IS 280 2006 PTCC shall confirm to CQA, EE, Pune specification No : CQAE / 5660/1602/A and controllerate of quality assurance of Engg. Equipment, PUNE Drawing No IMGA-0112/B ( Sheet 1 to 2) , IMGA- 0112/ C(Sheet 2 to 2), IMPD – 1817/B, IMPD – 1820, IMPD – 1821/B and IMPD -1822/B . |
| 58 | Fence New Design 55 | Fence Post : Type : Circular Hollow section Dimensions : outer dia pole 2.7". Inner pole dia 2.2" alongwith mushroom boltof size 8mm x 120mm, 3 mm (3mm +/- 0.3mm) thickness: All tolerances as per IS specnIS:1239 Length : 2.8mtrs (2.1 mtrs above ground level + 0.7 mtrs under the ground level). Weight : 15.02 Kg (+/-5%) Coating :Hot Dip galvanised to minimum 350 GSM Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123.Ref Drawing No : NC/LC/A1/V2.2. Fence Post- IS: 1239. Coating - as per IS 2629 / IS 4759 /ASTM A 123 Material: MS Steel Tube |
| 59 | Fence New Design 56 | I. Across Fence Post :- Clamp - 76 mm Dia, 35mm Width, 3mm Thick material MSwith hot dip galvanized to 350 GSM(2 Set per post). |
| 60 | Fence New Design 57 | (a) Mushroom Head bolt with breakable head nut M8X50 (4 per post) : material :SS Ref Drawing No :NC/LC/A6/V2.2. Material: MS strip as per IS 1730. IS : 8535 -1987. Material :SS 304 |
| 61 | Fence New Design 58 | II. Underground post fixing arrangement (a) Anchor Rod 10mm Dia 300 mm long GI Rod tie with fence post at bottom using tie wire.(2 Nos per post). |
| 62 | Fence New Design 59 | (b) Tie Wire – 1.4mm dia/ 100mm length. Wire : IS 280 2006MS Material (02 Nos per Anchor rod) Ref Drawing No :NC/LC/A6/V2.2. IS 280 2006.MS Material. MS Tie Wire:IS 280 2006 |
| 63 | Fence New Design 60 | III. PTCC Rod 12 mm dia 2.64 mm long MS Rod. Suitable arrangement be made on fence postfor holding of PTCC rod. Material MSwith hot dip galvanized to 350 GSM |
| 64 | Fence New Design 61 | IV. Post Cap. Ref Drawing No :NC/LC/A10/V2.2 IS: 1239. Material: MS |
| 65 | Fence New Design 62 | V.(a) Brace Band-76 mm 41mm Width, 4mm Thick material MSwith hot dip galvanized to 350 GSM(1 No per Bravo post) |
| 66 | Fence New Design 63 | (b) Mushroom Head bolt with breakable headsafety nut - M8X50, Material : SS Ref Drawing No :NC/LC/A6/V2.2. Material Ms Strip as per 1730.IS : 8535 -1987. Material :SS 304. |
| 67 | Fence New Design 64 | Hog ring, As per drawing. To secure PTC coil to PTC coil and also PTC coil to panels. Wire Dia : 3mm : shape and size as per drawing No NC/LC/A6/V2.2 dt 06 Nov 15. |
| 68 | Fence New Design 65 | Supply offoldable Weld Mesh Panels as per below spec. Mesh Wire :Horizontal wire, Dia 5.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.5 mm (+/-0.05mm)Mesh Size: Mesh Size of 50 x 100 mm - V Bend &50X200 mm (+/- 2 mm) along Mesh ( Mesh Wire: IS 280 2006). Panel size &Weight :2600X800 11.3 Kg with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place. Coating : Zinc coated 40-50GSM &60 to 80 microns of Powder coating. Color:RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength:Min 550 N/Sq.mm. Weld tensile strength:Min 70% of Wire tensile strength. Note: Weldmesh is installed vertically above the High Security Weldmesh Ref Drawing No :NC/LC/A8/V2.2. Material: MS Mesh Wire: Dia:4mm: IS 280 2006 Coating :IS 4826 – 1979 Weld Mesh as per : EN 10223-7 |
| 69 | Fence New Design 66 | Alpha Fence Supply of High SecurityFoldableWeld Mesh Panels as per below spec.Mesh Wire : Horizontal wire, Dia 4.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.0 mm (+/-0.05mm) Mesh Size: Mesh Size of 12.7 X 76.2 mm along Mesh ( Mesh Wire: IS 280 2006). Panel size &Weight : 2600X800mm: 22.52 Kg with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place.Coating : Zinc coated 40-50GSM &60 to 80 microns of Powder coating Color: RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength: Min 550 N/Sq.mm. Weld tensile strength: Min 70 % of Wire tensile strength. Note: High Security Weld mesh is been installed at the bottom.. Ref Drawing No :NC/LC/A8/V2.2. Material: MS Mesh Wire: Dia: 4mm: IS 280 2006 Coating :IS 4826 – 1979 Weld Mesh as per : EN 10223-7 |
| 70 | Fence New Design 67 | (Bravo Fence) Weld Mesh Panels: Mesh Wire : Horizontal wire, Dia 5.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.5 mm (+/-0.05mm)Mesh Size : Mesh Size of 50 x 100 mm - V Bend &50X200 mm (+/- 2 mm) along Mesh as per dwg.( Mesh Wire: IS 280 2006). Panel size (W &H) &Weight ( Tol +/-5%)2600X1000mm : 13.02 Kg, with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place.Surface of weld mesh panel must be absolutely plain without any intrinsic crests. Coating :Zinc coated 40-50 GSM&60 to 80 microns of Powder coating Color: RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength: Min 550 N/Sq.mm. Weld tensile strength: Min 70 % of Wire tensile strength. Ref Drawing No : NC/LC/A8/V2.2. Mesh Wire: IS 280 2006 Coating :IS 4826 – 1979 Material: MS Material Weld Mesh as per : EN 10223-7 |
| 71 | Fence New Design 68 | Punched Tape Baby Concertina Coil (including spike and handle) with 50 turns and dia 610 mm, having a core wire of high carbon spring steel of high tensile strength. The punched tape and core wire (2.6 ± 0.035 mm dia) are electro galvanised to provide protection against outdoor exposure. The punched tape is mechanically crimped over the core wire and then formed into a coil at various parts of the periphery of the coil; steel clips “total 70 Nos per coil equally spaced” to connect the individual turns of the coil to each other so that it opens up like an accordion. The width of strip as 19 mm and spacing of blades 24.00 ± 0.5 mm C/C. The weight of each coil will be 8 ± 5% Kgs without packing material and coil length 6-8 mtr when opened up with an effective height of 475 mm. Each coil wound with bituminised Hessian cloth for providing protective packing. (143 coils per Km).23 |
| 72 | Fence New Design 69 | Punched Tape Concertina Coil : 850 mm Dia / 18 loops / 3.5 mm core wire.Coil Diameter : 850 mm (+/- 50mm). Blade Profile : Tear Blade Profile. Core Wire : High Tensile, 3.5 mm (+/-0.1mm) Dia. Zinc coating : Galvanised to min : 275 GSM. Tensile Strength of Wire: 1400 – 1500 N/sq.mm. Number of loops: 18. Stretchable length: 2.5 mtrs. Locking Clips: 5 clips per set of loops. Weight: 6.7 Kgs (+/-5%). Ref Drawing No :NC/LC/A2/V2.2. Specn for Steel Strip: IS 1730 Specn for wire: IS 280 2006 Specification for coating : Min 275 GSM Zinc coating as per IS 6745 / 1972 reaffirmed 2006 PTCC shall confirm to CQA, EE, Pune specification No : CQAE / 5660/1602/A and controllerate of quality assurance of Engg. Equipment, PUNE Drawing No IMGA-0112/B ( Sheet 1 to 2) , IMGA- 0112/ C(Sheet 2 to 2), IMPD – 1817/B, IMPD – 1820, IMPD – 1821/B and IMPD -1822/B . |
| 73 | Fence New Design 70 | Fence Post : Type : Circular Telescopic Hollow section, dimensions outer pole dia 2.7" inner pole dia 2.2" along with mushroom bolt of size 18 mm x 120 mm .Dimensions : 2.7 inch,Dia, 3 mm (3mm +/- 0.3mm) Thickness: inner pole dia 2.2 inch along with two mushroom bolt and nutsize 18mm x 120 mmAll tolerances as per IS specnIS: 1239 Length : 3.4 mtrs B 2.7 mtrs above ground level + 0.7 mtrs under the ground level). Weight: 21.6 Kg (+/-5 %) Coating : Hot Dip glvanised to minimum 350 GSM Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123Ref Drawing No :NC/LC/A6/V2.2. Fence Post- IS: 1239 Material: MS Steel Tube |
| 74 | Fence New Design 71 | (I) Truss support Post with Rail end Cap : Type : Circular Hollow section. Dimensions :76mm Dia, 3 mm (3mm +/- 0.3mm).Rail End Cap Fitting -76 mm (Rail End Cap is fitted to Truss Support using M8X100 Nut and Bolt Mechanism).Thickness: All tolerances as per IS specnIS:1239. Length &Weight. 1. Truss support for across the slope condition. Length :1800mm, Weight : 9.65 Kg(+5%). Coating : Hot Dip galvanised to minimum 350 GSM. Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123. |
| 75 | Fence New Design 72 | (II) Truss support Post with Rail end Cap : Type : Circular Hollow section. Dimensions :76mm Dia, 3 mm (3mm +/- 0.3mm).Rail End Cap Fitting -76 mm (Rail End Cap is fitted to Truss Support using M8X100 Nut and Bolt Mechanism).Thickness: All tolerances as per IS specnIS:1239. Length &Weight. 1. Truss support for along the slope condition. Length:3100mm, Weight : 16.6 Kg(+5%).. Coating : Hot Dip galvanised to minimum 350 GSM. Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123. Ref Drawing No:NC/LC/A1/V2.2.Fence Post- IS: 1239. Coating - as per IS 2629 / IS 4759 /ASTM A 123. Material: MS Steel Tube Tangdhar Nos640 |
| 76 | Fence New Design 73 | Straining Y-Arm for supporting top PTCC: Material : CHS of Dia 60 mm Length 100mmand 3.2mm guage as per IS 1852. Coating : Hot dip galvanized to Min 350 GSM as per IS 4759/2629, Length of 1 Arm is 510 mm,outer dia of 50 mm of sleeve cap will be fitted on the top of the fence post and fixed with two Nos mushroom head bolt andnut (M8x25mm). Straining Y-Arm will manufactured as per drawing attached. Straining Y Arm will be installed at every 10 mtrs except intermediate arm post. |
| 77 | Fence New Design 74 | Intermediate Y-Arm for supporting top PTCC: Material: CHS of Dia 50 mm Length 100mm and 2.90mm guage as per IS1852 Coating :Hot dip galvanized to Min 350 GSM as per IS 4759 / IS 2629.Length of 1 Arm is510 MM , Angle between the two arms is 120 degree , fixed with two Nos mushroom head bolt andnut (M8x25mm).Intermediate Y-Arm will manufactured as per drawing attached. Outer dia of 76 mm of sleeve cap will be fitted on the top of the fence post. One Intermediate YArm will be installed at every post except the posts with Straining Y arms |
| 78 | Fence New Design 75 | Razor Running Tape Blade profile : Tear Blade Corewire : 2.5 mm wire Dia +0.1mm, Length of each Coil : 95 Mtrs Weight of each coil : 9.2 Kg.Ref Drawing No : NC/LC/A2/V2.2. Specn for Steel Strip: IS 1730 Specn for wire: IS 280 2006 |
| 79 | Fence New Design 76 | I. Accessories for fitting panel :-Omega Clamp - 89 mm Dia, 35mm Width, 3mm Thick Flat - 35mm Width, 5mm Thickmaterial MSwith hot dip galvanized to 350 GSM.(6 Nos per post) |
| 80 | Fence New Design 77 | (a) Mushroom Head bolt with breakable headsafety nut (12 per post) - M8X50, SS material. Ref Drawing No : NC/LC/A6/V2.2 (For A10). Material Ms Strip as per 1730. IS : 8535 -1987. Material :SS 304 |
| 81 | Fence New Design 78 | II. Accessories for fitting Truss Support Post:- (a) Brace Band-89 mm 41mm Width, 4mm Thick material MSwith hot dip galvanized to 350 GSM.(1 No per Alpha post). |
| 82 | Fence New Design 79 | III. Accessories for fitting Y Arm :- (a). Mushroom Head Bolt with breakable head safety nut (M8X120) (2No per post): Material : SS 304 |
| 83 | Fence New Design 80 | (b) Eye Bolt with Loop nut M8X100, Material SS. There will be 6 eye bolts for each straining Y Arm. There are 34 straining Y Arm per KM. So 204 eye bolts are required for per KM.. Material :SS. Material Ms Strip as per 1730. IS : 8535 -1987. |
| 84 | Fence New Design 81 | IV. Underground post fixing arrangement:- (a)Anchor Rod 10mm Dia 300mm long GI Rod tie with fence post at bottom using tie wire.(2 Nos per post). Holes of suitable dimention will be provided at lower end of fence post to insert the anchor rod into it. |
| 85 | Fence New Design 82 | (b) Tie Wire – 1.4mm dia/ 100mm length. Wire : IS 280 2006MS Material (02 Nos per Anchor rod) |
| 86 | Fence New Design 83 | V (a) Flat clamps for panel connection Flat 25x3, 160mm long, 2-slots |
| 87 | Fence New Design 84 | (b) SS 304 Mushroom head bolt, M8X25 Sheet Metal IS 1730. IS : 8535 -1987. Material :SS 304 |
| 88 | Fence New Design 85 | VI. Hog ring, As per drawing. To secure PTC coil to PTC coil and also PTC coil to panels. Wire Dia : 3mm : shape and size as per drawing No NC/LC/A6/V2.2 dt 06 Nov 15. |
| 89 | Fence New Design 86 | Punched Tape Concertina coil: 1050 mm Dia /18 loops/ 3.5 mm core wire. Coil Diameter: 1050 mm (+/- 50mm). Blade Profile : Tear Blade profile. Core wire: High Tensile , 3.5 mm (+/- 0.1mm) Dia. Zinc coating :Galvanised to min: 275 GSM.Tensile strength of wire :1400 – 1500 N/sq.mm. Number of loops :18. Stretchable length : 2.5 mtrs.Locking clips :7 clips per set of two loops. Weight : 8.2 Kg (+/-5%). Ref Drawing No : NC/LC/A3/V2.2. Specn for Steel Strip: IS 1730. Specn for wire: IS 280 2006 PTCC shall confirm to CQA, EE, Pune specification No : CQAE / 5660/1602/A and controllerate of quality assurance of Engg. Equipment, PUNE Drawing No IMGA-0112/B ( Sheet 1 to 2) , IMGA- 0112/ C(Sheet 2 to 2), IMPD – 1817/B, IMPD – 1820, IMPD – 1821/B and IMPD -1822/B . |
| 90 | Fence New Design 87 | Fence Post : Type : Circular Hollow section Dimensions : outer dia pole 2.7". Inner pole dia 2.2" alongwith mushroom boltof size 8mm x 120mm, 3 mm (3mm +/- 0.3mm) thickness: All tolerances as per IS specnIS:1239 Length : 2.8mtrs (2.1 mtrs above ground level + 0.7 mtrs under the ground level). Weight : 15.02 Kg (+/-5%) Coating :Hot Dip galvanised to minimum 350 GSM Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123.Ref Drawing No : NC/LC/A1/V2.2. Fence Post- IS: 1239. Coating - as per IS 2629 / IS 4759 /ASTM A 123 Material: MS Steel Tube |
| 91 | Fence New Design 88 | I. Across Fence Post :- Clamp - 76 mm Dia, 35mm Width, 3mm Thick material MSwith hot dip galvanized to 350 GSM(2 Set per post). |
| 92 | Fence New Design 89 | (a) Mushroom Head bolt with breakable head nut M8X50 (4 per post) : material :SS Ref Drawing No :NC/LC/A6/V2.2. Material: MS strip as per IS 1730. IS : 8535 -1987. Material :SS 304 |
| 93 | Fence New Design 90 | II. Underground post fixing arrangement (a) Anchor Rod 10mm Dia 300 mm long GI Rod tie with fence post at bottom using tie wire.(2 Nos per post). |
| 94 | Fence New Design 91 | (b) Tie Wire – 1.4mm dia/ 100mm length. Wire : IS 280 2006MS Material (02 Nos per Anchor rod) Ref Drawing No :NC/LC/A6/V2.2. IS 280 2006.MS Material. MS Tie Wire:IS 280 2006 |
| 95 | Fence New Design 92 | III. PTCC Rod 12 mm dia 2.64 mm long MS Rod. Suitable arrangement be made on fence postfor holding of PTCC rod. Material MSwith hot dip galvanized to 350 GSM |
| 96 | Fence New Design 93 | IV. Post Cap. Ref Drawing No :NC/LC/A10/V2.2 IS: 1239. Material: MS |
| 97 | Fence New Design 94 | V.(a) Brace Band-76 mm 41mm Width, 4mm Thick material MSwith hot dip galvanized to 350 GSM(1 No per Bravo post) |
| 98 | Fence New Design 95 | (b) Mushroom Head bolt with breakable headsafety nut - M8X50, Material : SS Ref Drawing No :NC/LC/A6/V2.2. Material Ms Strip as per 1730.IS : 8535 -1987. Material :SS 304. |
| 99 | Fence New Design 96 | Hog ring, As per drawing. To secure PTC coil to PTC coil and also PTC coil to panels. Wire Dia : 3mm : shape and size as per drawing No NC/LC/A6/V2.2 dt 06 Nov 15. |
| 100 | Fence New Design 97 | Supply offoldable Weld Mesh Panels as per below spec. Mesh Wire :Horizontal wire, Dia 5.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.5 mm (+/-0.05mm)Mesh Size: Mesh Size of 50 x 100 mm - V Bend &50X200 mm (+/- 2 mm) along Mesh ( Mesh Wire: IS 280 2006). Panel size &Weight :2600X800 11.3 Kg with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place. Coating : Zinc coated 40-50GSM &60 to 80 microns of Powder coating. Color:RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength:Min 550 N/Sq.mm. Weld tensile strength:Min 70% of Wire tensile strength. Note: Weldmesh is installed vertically above the High Security Weldmesh Ref Drawing No :NC/LC/A8/V2.2. Material: MS Mesh Wire: Dia:4mm: IS 280 2006 Coating :IS 4826 – 1979 Weld Mesh as per : EN 10223-7 |
| 101 | Fence New Design 98 | Alpha Fence Supply of High SecurityFoldableWeld Mesh Panels as per below spec.Mesh Wire : Horizontal wire, Dia 4.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.0 mm (+/-0.05mm) Mesh Size: Mesh Size of 12.7 X 76.2 mm along Mesh ( Mesh Wire: IS 280 2006). Panel size &Weight : 2600X800mm: 22.52 Kg with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place.Coating : Zinc coated 40-50GSM &60 to 80 microns of Powder coating Color: RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength: Min 550 N/Sq.mm. Weld tensile strength: Min 70 % of Wire tensile strength. Note: High Security Weld mesh is been installed at the bottom.. Ref Drawing No :NC/LC/A8/V2.2. Material: MS Mesh Wire: Dia: 4mm: IS 280 2006 Coating :IS 4826 – 1979 Weld Mesh as per : EN 10223-7 |
| 102 | Fence New Design 99 | (Bravo Fence) Weld Mesh Panels: Mesh Wire : Horizontal wire, Dia 5.0 mm (+/- 0.05mm) : Vertical wire, Dia 4.5 mm (+/-0.05mm)Mesh Size : Mesh Size of 50 x 100 mm - V Bend &50X200 mm (+/- 2 mm) along Mesh as per dwg.( Mesh Wire: IS 280 2006). Panel size (W &H) &Weight ( Tol +/-5%)2600X1000mm : 13.02 Kg, with equidistant hinges at 850 mm.Each hinges would be of size 3" x 1.5 " min 4 hinges & max 6 would be required for one panel using MS plate of thickness 6 mm with adequate screws to hold them in place.Surface of weld mesh panel must be absolutely plain without any intrinsic crests. Coating :Zinc coated 40-50 GSM&60 to 80 microns of Powder coating Color: RAL 6005. Powder coating should withstand 1000 Hours of salt spray test. Wire Tensile Strength: Min 550 N/Sq.mm. Weld tensile strength: Min 70 % of Wire tensile strength. Ref Drawing No : NC/LC/A8/V2.2. Mesh Wire: IS 280 2006 Coating :IS 4826 – 1979 Material: MS Material Weld Mesh as per : EN 10223-7 |
| 103 | Fence New Design 100 | Punched Tape Baby Concertina Coil (including spike and handle) with 50 turns and dia 610 mm, having a core wire of high carbon spring steel of high tensile strength. The punched tape and core wire (2.6 ± 0.035 mm dia) are electro galvanised to provide protection against outdoor exposure. The punched tape is mechanically crimped over the core wire and then formed into a coil at various parts of the periphery of the coil; steel clips “total 70 Nos per coil equally spaced” to connect the individual turns of the coil to each other so that it opens up like an accordion. The width of strip as 19 mm and spacing of blades 24.00 ± 0.5 mm C/C. The weight of each coil will be 8 ± 5% Kgs without packing material and coil length 6-8 mtr when opened up with an effective height of 475 mm. Each coil wound with bituminised Hessian cloth for providing protective packing. (143 coils per Km).23 |
| 104 | Fence New Design 101 | Punched Tape Concertina Coil : 850 mm Dia / 18 loops / 3.5 mm core wire.Coil Diameter : 850 mm (+/- 50mm). Blade Profile : Tear Blade Profile. Core Wire : High Tensile, 3.5 mm (+/-0.1mm) Dia. Zinc coating : Galvanised to min : 275 GSM. Tensile Strength of Wire: 1400 – 1500 N/sq.mm. Number of loops: 18. Stretchable length: 2.5 mtrs. Locking Clips: 5 clips per set of loops. Weight: 6.7 Kgs (+/-5%). Ref Drawing No :NC/LC/A2/V2.2. Specn for Steel Strip: IS 1730 Specn for wire: IS 280 2006 Specification for coating : Min 275 GSM Zinc coating as per IS 6745 / 1972 reaffirmed 2006 PTCC shall confirm to CQA, EE, Pune specification No : CQAE / 5660/1602/A and controllerate of quality assurance of Engg. Equipment, PUNE Drawing No IMGA-0112/B ( Sheet 1 to 2) , IMGA- 0112/ C(Sheet 2 to 2), IMPD – 1817/B, IMPD – 1820, IMPD – 1821/B and IMPD -1822/B . |
| 105 | Fence New Design 102 | Fence Post : Type : Circular Telescopic Hollow section, dimensions outer pole dia 2.7" inner pole dia 2.2" along with mushroom bolt of size 18 mm x 120 mm .Dimensions : 2.7 inch,Dia, 3 mm (3mm +/- 0.3mm) Thickness: inner pole dia 2.2 inch along with two mushroom bolt and nutsize 18mm x 120 mmAll tolerances as per IS specnIS: 1239 Length : 3.4 mtrs B 2.7 mtrs above ground level + 0.7 mtrs under the ground level). Weight: 21.6 Kg (+/-5 %) Coating : Hot Dip glvanised to minimum 350 GSM Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123Ref Drawing No :NC/LC/A6/V2.2. Fence Post- IS: 1239 Material: MS Steel Tube |
| 106 | Fence New Design 103 | (I) Truss support Post with Rail end Cap : Type : Circular Hollow section. Dimensions :76mm Dia, 3 mm (3mm +/- 0.3mm).Rail End Cap Fitting -76 mm (Rail End Cap is fitted to Truss Support using M8X100 Nut and Bolt Mechanism).Thickness: All tolerances as per IS specnIS:1239. Length &Weight. 1. Truss support for across the slope condition. Length :1800mm, Weight : 9.65 Kg(+5%). Coating : Hot Dip galvanised to minimum 350 GSM. Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123. |
| 107 | Fence New Design 104 | (II) Truss support Post with Rail end Cap : Type : Circular Hollow section. Dimensions :76mm Dia, 3 mm (3mm +/- 0.3mm).Rail End Cap Fitting -76 mm (Rail End Cap is fitted to Truss Support using M8X100 Nut and Bolt Mechanism).Thickness: All tolerances as per IS specnIS:1239. Length &Weight. 1. Truss support for along the slope condition. Length:3100mm, Weight : 16.6 Kg(+5%).. Coating : Hot Dip galvanised to minimum 350 GSM. Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123. Ref Drawing No:NC/LC/A1/V2.2.Fence Post- IS: 1239. Coating - as per IS 2629 / IS 4759 /ASTM A 123. Material: MS Steel Tube Tangdhar Nos640 |
| 108 | Fence New Design 105 | Straining Y-Arm for supporting top PTCC: Material : CHS of Dia 60 mm Length 100mmand 3.2mm guage as per IS 1852. Coating : Hot dip galvanized to Min 350 GSM as per IS 4759/2629, Length of 1 Arm is 510 mm,outer dia of 50 mm of sleeve cap will be fitted on the top of the fence post and fixed with two Nos mushroom head bolt andnut (M8x25mm). Straining Y-Arm will manufactured as per drawing attached. Straining Y Arm will be installed at every 10 mtrs except intermediate arm post. |
| 109 | Fence New Design 106 | Intermediate Y-Arm for supporting top PTCC: Material: CHS of Dia 50 mm Length 100mm and 2.90mm guage as per IS1852 Coating :Hot dip galvanized to Min 350 GSM as per IS 4759 / IS 2629.Length of 1 Arm is510 MM , Angle between the two arms is 120 degree , fixed with two Nos mushroom head bolt andnut (M8x25mm).Intermediate Y-Arm will manufactured as per drawing attached. Outer dia of 76 mm of sleeve cap will be fitted on the top of the fence post. One Intermediate YArm will be installed at every post except the posts with Straining Y arms |
| 110 | Fence New Design 107 | Razor Running Tape Blade profile : Tear Blade Corewire : 2.5 mm wire Dia +0.1mm, Length of each Coil : 95 Mtrs Weight of each coil : 9.2 Kg.Ref Drawing No : NC/LC/A2/V2.2. Specn for Steel Strip: IS 1730 Specn for wire: IS 280 2006 |
| 111 | Fence New Design 108 | I. Accessories for fitting panel :-Omega Clamp - 89 mm Dia, 35mm Width, 3mm Thick Flat - 35mm Width, 5mm Thickmaterial MSwith hot dip galvanized to 350 GSM.(6 Nos per post) |
| 112 | Fence New Design 109 | (a) Mushroom Head bolt with breakable headsafety nut (12 per post) - M8X50, SS material. Ref Drawing No : NC/LC/A6/V2.2 (For A10). Material Ms Strip as per 1730. IS : 8535 -1987. Material :SS 304 |
| 113 | Fence New Design 110 | II. Accessories for fitting Truss Support Post:- (a) Brace Band-89 mm 41mm Width, 4mm Thick material MSwith hot dip galvanized to 350 GSM.(1 No per Alpha post). |
| 114 | Fence New Design 111 | III. Accessories for fitting Y Arm :- (a). Mushroom Head Bolt with breakable head safety nut (M8X120) (2No per post): Material : SS 304 |
| 115 | Fence New Design 112 | (b) Eye Bolt with Loop nut M8X100, Material SS. There will be 6 eye bolts for each straining Y Arm. There are 34 straining Y Arm per KM. So 204 eye bolts are required for per KM.. Material :SS. Material Ms Strip as per 1730. IS : 8535 -1987. |
| 116 | Fence New Design 113 | IV. Underground post fixing arrangement:- (a)Anchor Rod 10mm Dia 300mm long GI Rod tie with fence post at bottom using tie wire.(2 Nos per post). Holes of suitable dimention will be provided at lower end of fence post to insert the anchor rod into it. |
| 117 | Fence New Design 114 | (b) Tie Wire – 1.4mm dia/ 100mm length. Wire : IS 280 2006MS Material (02 Nos per Anchor rod) |
| 118 | Fence New Design 115 | V (a) Flat clamps for panel connection Flat 25x3, 160mm long, 2-slots |
| 119 | Fence New Design 116 | (b) SS 304 Mushroom head bolt, M8X25 Sheet Metal IS 1730. IS : 8535 -1987. Material :SS 304 |
| 120 | Fence New Design 117 | VI. Hog ring, As per drawing. To secure PTC coil to PTC coil and also PTC coil to panels. Wire Dia : 3mm : shape and size as per drawing No NC/LC/A6/V2.2 dt 06 Nov 15. |
| 121 | Fence New Design 118 | Punched Tape Concertina coil: 1050 mm Dia /18 loops/ 3.5 mm core wire. Coil Diameter: 1050 mm (+/- 50mm). Blade Profile : Tear Blade profile. Core wire: High Tensile , 3.5 mm (+/- 0.1mm) Dia. Zinc coating :Galvanised to min: 275 GSM.Tensile strength of wire :1400 – 1500 N/sq.mm. Number of loops :18. Stretchable length : 2.5 mtrs.Locking clips :7 clips per set of two loops. Weight : 8.2 Kg (+/-5%). Ref Drawing No : NC/LC/A3/V2.2. Specn for Steel Strip: IS 1730. Specn for wire: IS 280 2006 PTCC shall confirm to CQA, EE, Pune specification No : CQAE / 5660/1602/A and controllerate of quality assurance of Engg. Equipment, PUNE Drawing No IMGA-0112/B ( Sheet 1 to 2) , IMGA- 0112/ C(Sheet 2 to 2), IMPD – 1817/B, IMPD – 1820, IMPD – 1821/B and IMPD -1822/B . |
| 122 | Fence New Design 119 | Fence Post : Type : Circular Hollow section Dimensions : outer dia pole 2.7". Inner pole dia 2.2" alongwith mushroom boltof size 8mm x 120mm, 3 mm (3mm +/- 0.3mm) thickness: All tolerances as per IS specnIS:1239 Length : 2.8mtrs (2.1 mtrs above ground level + 0.7 mtrs under the ground level). Weight : 15.02 Kg (+/-5%) Coating :Hot Dip galvanised to minimum 350 GSM Hot Dip Galavanising as per IS 2629 / IS 4759 /ASTM A 123.Ref Drawing No : NC/LC/A1/V2.2. Fence Post- IS: 1239. Coating - as per IS 2629 / IS 4759 /ASTM A 123 Material: MS Steel Tube |
| 123 | Fence New Design 120 | I. Across Fence Post :- Clamp - 76 mm Dia, 35mm Width, 3mm Thick material MSwith hot dip galvanized to 350 GSM(2 Set per post). |
| 124 | Fence New Design 121 | (a) Mushroom Head bolt with breakable head nut M8X50 (4 per post) : material :SS Ref Drawing No :NC/LC/A6/V2.2. Material: MS strip as per IS 1730. IS : 8535 -1987. Material :SS 304 |
| 125 | Fence New Design 122 | II. Underground post fixing arrangement (a) Anchor Rod 10mm Dia 300 mm long GI Rod tie with fence post at bottom using tie wire.(2 Nos per post). |
| 126 | Fence New Design 123 | (b) Tie Wire – 1.4mm dia/ 100mm length. Wire : IS 280 2006MS Material (02 Nos per Anchor rod) Ref Drawing No :NC/LC/A6/V2.2. IS 280 2006.MS Material. MS Tie Wire:IS 280 2006 |
| 127 | Fence New Design 124 | III. PTCC Rod 12 mm dia 2.64 mm long MS Rod. Suitable arrangement be made on fence postfor holding of PTCC rod. Material MSwith hot dip galvanized to 350 GSM |
| 128 | Fence New Design 125 | IV. Post Cap. Ref Drawing No :NC/LC/A10/V2.2 IS: 1239. Material: MS |
| 129 | Fence New Design 126 | V.(a) Brace Band-76 mm 41mm Width, 4mm Thick material MSwith hot dip galvanized to 350 GSM(1 No per Bravo post) |
| 130 | Fence New Design 127 | (b) Mushroom Head bolt with breakable headsafety nut - M8X50, Material : SS Ref Drawing No :NC/LC/A6/V2.2. Material Ms Strip as per 1730.IS : 8535 -1987. Material :SS 304. |
| 131 | Fence New Design 128 | Hog ring, As per drawing. To secure PTC coil to PTC coil and also PTC coil to panels. Wire Dia : 3mm : shape and size as per drawing No NC/LC/A6/V2.2 dt 06 Nov 15. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
