Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 25-11-2021 | Amendment No 2 | Technical Bid | 01-12-2021 |
| 2 | 17-11-2021 | Amendment No.1 | Date | 01-12-2021 |
| Sl. No. | Item Description |
| 1 | BILL No;1Construction of Paver Block Yard and Approach Road |
| 2 | 1. Earth work excavation of all kinds of soil by mechanical means (Hydraulic excavator) / manual means over areas for yard and road including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed and wherever required including dressing of sides ramming of bottom all as per relevant specification, drawings and as directed,including shoring, strutting, dewatering, if required, includingall labour, tools, tackles, equipments, fuel etc., complete. |
| 3 | 2. Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres all as per relevant specification, drawings and as directed including all labour, machinery charges etc.,equipments, fuel etc., complete. |
| 4 | 3. Supplying and filling Quarry dust to a thickness of 150mm over sub grade watering and consolidating the same including making good without undulations, consolidating the same in layers by watering and ramming all as per specifications and as per directions of including all labour,materials, tools and plants, equipment, etc., complete. |
| 5 | 4. Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and Compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per MoRT&H clause 406 specifications and directions of Engineer-in-Charge including all labour,materials, tools and plants, equipment, fuel etc., complete. |
| 6 | 5. Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum and all as perMoRT&H relevant specification, concrete strength not to be less than 10 Mpa at 7days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in-chargeincluding all materials, labour, tools, equipment, transport, fuel etc., complete. |
| 7 | 6. Supplying and Laying the P.C.C single layer monolithic Paving blocks of M40 grade of size 200mm x 100 mm x 120 mm thick to a correct alignment and gradient in approved pattern and/or as directed by the Engineer incharge over the 25mm crusher sand filling and setting the blocks with hand tight and compacting using vibrator to bring out joints not more than 5mm wide between the blocks including brushing the crusher sandinto the joints to fill the gap wherever required and vibrating again so as to achieve full interlock of required shape and size all as directed at site of work including 25mm crusher sand filling, all labour, materials, tools, equipments, transport etc.,complete. |
| 8 | 7.Providing and laying Plain Cement Concrete of mix 1:4:8 (1 Cement: 4 CS sand: 8hard granite graded stone aggregate of 40 mm nominal size) in volumetric proportions for levelling course foryard retaining wall and wherever required all as per relevant specification, drawing and as directed including mixing, transporting, placing, ramming, consolidating, shuttering,curing etc., including all materials, labour, formwork, tools, plants, equipments, fuel, etc. complete. |
| 9 | 8. Providing and laying Reinforced Cement Concrete of mix 1:1.5:3 (1 cement: 1.5 C.S.sand : 3 Coarse aggregate) using hard granite graded stone aggregate of 20 mm nominal size in volumetric proportions for end wall for paver block all as per relevant specifications, drawings and as directed including mixing, transporting, shuttering, placing, vibrating, curing etc., includingall materials, labour, tools, equipment, etc., complete.Note: Providing Steel reinforcement will be measured and paid for separately under relevant item. |
| 10 | 9. Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 CS sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not be more than 5mm), including making drainage opening wherever required complete etc. as per Specification and direction of Engineer-in-charge including all labour, materials, tools, equipment, transport, fuel etc., Note:1. length of finished kerb edging shall be measured for payment. 2. Precast C.C. kerb stone shall be approved by Engineer-in-charge. |
| 11 | 10. Supplying, fabricating and placing in position HYSDFe 500 or moreGrade TMT steelbars asreinforcementfor all RCC works wherever required, including handling, cutting, bending and tying with 1.25 mm dia black annealed steel binding wire, all as per relevant specification and as directedincluding all materials, labours, tools, equipments,etc., complete.Note: The rate shall be inclusive of cost of steel, binding wire and fabrication charge etc., complete. Binding wire will not be measured for payment purpose. |
| 12 | 11. Supplying stacking and Laying, spreading and compacting stone aggregate of specified sizes to specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density as specified in railway manual or CPWD or as directed by Engineer-in charge, including all materials, labours,tools,equipmetns, machinery, fuel etc., complete11.a Bottom layer - Stone aggregate of size 106-75mm -230 mm thick |
| 13 | 11.b Middle layer - Stone aggregate of size 63-45mm -100 mm thick |
| 14 | 11. cTop layer - Stone aggregate of size 53-22mm -75mm thick |
| 15 | 12a. Providing and laying 40mm thk premix carpet surfacing with 1.8 cum and 0.90 cum of stone chippings of 13.2 mm size and 11.2 mm size respectively per 100sqm and 52 kg and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively, including a tack coat With medium setting bitumen emulsion at 0.40 kg/Sqm with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity with paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt all as perspecification and as directed including all labour, materials, tools, equipments,machineries, transport, fuel etc.,complete. |
| 16 | 12.b.Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface, including rolling and finishing with road roller,including all labour, materials, tools, equipments,machineries, transport, fuel etc.,complete. |
| 17 | 13. Loading, transporting the Surplus earth, dumping and leveling in the low lying area within a lead of 2Km and as directed, including all labour, transport, tools, equipments, fuel, etc, complete.Note: 1. Tenderer shall maintain trip sheets in triplicate in Trust’s approved format at his own cost for the quantity of earth transported.2.Payment will be based on lorry cubical content after deduction of 20% for voids. However, for final payment, final quantity will be restricted to actual quantity of earth work minus refilling. |
| 18 | 14. Painting with two coats of synthetic enamel paint (Asian or other approved brands)of approved quality to give an even shade, all as directedincludingall materials, labour, brushes, tools, equipments, etc. complete |
| 19 | 15.Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-chargeincludingall materials, labour, brushes, tools, equipments, etc. complete15.a Red studs |
| 20 | 15.b. Yellow studs |
| 21 | 16. Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specificationsincludingall materials, labour, tools, equipments, etc. complete |
| 22 | 17. Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual),symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge including all labour, materials, tools, equipments,welding, fuel etc.,complete. Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm |
| 23 | 18. Supplying and erecting RO plant - 50 Litres per hour having minimum 4 Nos memberances, pumps of2 Nos, SV -1 No, SMBS 2 Nos, Carbon filter -1 No, Sediment filters - 2 Nos, Posted carbon 1 No, storage tank with stand etc all as per standard specification and relevant standards or as directed at site etc., complete including all labour materrials transport, tools etc., complete., |
| 24 | 19. Supply and Installation of HP Desktop Computer with HP A4printer cum scanner or equivalent with following specifications:10th Gen Core i3/ 3.6Ghz/windows 10 home/Microsoft office 2019 / 4GB DDR4 / 1TB HDD /Intel Hd Garphics/Serial port /wlan/bluetooth/HDMI/wired Keyboard & Mouse / 18.5\" monitor LED monitor with CPU one year warranty / Monitor 3 year warranty.HP 1136 MFP Laser Printer or Equivalent.all as per specification and as directed including all labour materials transport etc., |
| 25 | 20. Providing and supplying required Office Stationaries for minimum 6 months., including prepaid wi-fi dongle with unlimited data pack for minimum 6 months.The following are the items to be supplied for the contract period:One time at the start of contract period:1) Pre-paid wi-fi dongle and wifi adapter with unlimited data package validity fo rsix months - 1no2) Double hole Punching machine medium size -2nos3) Single hole Punching machine - 1no , 4) Steel scale - 2nos, 5) Box File - 5 nos, 6) Stapler - 2nos, 7) Paper clip big - 1box, 8) Paper clip small - 1box, 9) White board- 4\" x 3\" - 1noEvery Month thorughout contract period:1) A4 paper - 2bundles , 2) Flat file - 3nos 3) Pen - 5nos(Blue-2, Black -1, Red -1, Green-1), 4) Pencil - 1 box, 5) Eraser - 3nos, 6) Ink eraser -1 no, 7) Jump clip - 1box, 8) Stapler pin - 3box, 9) Permanenat marker - 1no, 10) white board marker - 2nos, 11) Colour sketch - 1set, 12) Crayons - 1set, 13) Colour pencil - 1set, 14) Ruled note long size(192pg) - 4nos, 15) unruled long size - 1no, 16) Tags 1 bunch, 17) stick on pad - 1 small size, 18)Clour flag set - 1pad, 19) Scrippling pad -3 Nos etc., |
| 26 | BILL No;2CONSTRUCTION OF REST ROOM, DALAL ROOM AND TOILET BLOCKS |
| 27 | 1. Earth work excavation of all kinds of soil by mechanical means (Hydraulic excavator) / manual means over areasincluding getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed and wherever required including dressing of sides ramming of bottom all as per relevant specification, drawings and as directed,including shoring, strutting, dewatering, if required, includingall labour, tools, tackles, equipments, fuel etc., complete. |
| 28 | 2. Supplying and filling river sand infoundation andbasement all as per relevant specification, drawings and as directed in layers not exceeding 150mm, consolidating by watering and ramming including all materials, labour, tools, equipments etc., complete., |
| 29 | 3. Providing and laying plain cement concrete of mix 1:4:8 (1 Cement: 4 Crushed Stone sand : 8 hard granite graded stone aggregate of 40 mm nominal size) in volumetric proportions for levelling course in foundations /flooring concrete and wherever required all as per relevant specification, drawings and as directed including mixing, transporting, placing, ramming, consolidating, curing, shuttering, dewatering if any etc., including all materials, labour, tools, plants, equipments, fuel, etc. complete. |
| 30 | 4. Brick Work using Non-modular Common burnt clay bricks class designation 7.5 in CM 1:6 ( 1 cement : 6 Crushed Stone sand )for foundation and basement and wherever required, curing all as per relevant specifications, drawingsand as directedincludingall materials, labour, tools, equipment, scaffolding, transport,fuel etc. complete. |
| 31 | 5. Refilling with available excavated earth (excluding boulders, rubbish, debris etc.,) in sides offoundation and in basement etc.,inlayersnot exceeding 200mm, thick and all as directed consolidating the deposited earth in layers by watering and ramming including all labour, tools, equipment, etc., complete. |
| 32 | 6. Brick Work using Non-modular Common burnt clay bricks class designation 7.5 in CM 1:4 ( 1 cement : 4 Crushed Stone sand )for Super structure and wherever required, curing all as per relevant specifications, drawingsand as directedincludingall materials, labour, tools, equipment, scaffolding, transport,fuel etc. complete. |
| 33 | 7. Half Brick work using Non-modular Common burnt clay bricks class designation 7.5 in CM1:4 (1 cement : 4 Crushed Stone sand) wherever required, curing all as perrelevant specifications, drawings, and as directedincluding all labour, materials, tools, equipment, scaffolding, transport, fuel etc., complete. |
| 34 | 8. Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 Crushed stone sand : 4 graded stone aggregate of 12.5mm nominal size) curing all as perrelevant specifications, drawings, and as directedincluding all labour, materials, tools, equipment, scaffolding, transport, fuel etc., complete. |
| 35 | 9.Providing and laying cement concrete in mix 1:1½:3 (1 Cement : 1½ Crushed Stone sand : 3 hard granite graded stone aggregate of 20 mm nominal size) in volumetric proportions forR.C.C in-situ lintelin the existing buildings and wherever required, including centering, shuttering, mixing, transporting, placing, vibrating , curing all as per relevantspecifications ,drawings and as directed , including all materials, labour, tools, equipment, transport, fuel, scaffolding etc. complete.Note: Providing Steel reinforcement will be measured and paid for separately under relevant item. |
| 36 | 10. Providing and laying cement concrete in mix 1:1½:3 (1 Cement : 1½ Crushed Stone sand : 3 hard granite graded stone aggregate of 20 mm nominal size) in volumetric proportions for RCC Sunshade including centering, shuttering, mixing, transporting, placing, compacting, curing all as per relevantspecifications, drawingsand as directedincluding allmaterials, labour, tools, equipments, scaffolding, transport, fuel etc., complete. Note: Providing Steel reinforcement will be measured and paid for separately under relevant item. |
| 37 | 11. Providing and laying cement concrete in mix 1:1½:3 (1 Cement : 1½ Crushed Stone sand : 3 hard granite graded stone aggregate of 20 mm nominal size) in volumetric proportions for RCC Roof slab including centering, shuttering, mixing, transporting, placing, compacting, curing all as per relevantspecifications, drawingsand as directedincluding allmaterials, labour, tools, equipments, scaffolding, transport, fuel etc., complete. Note: Providing Steel reinforcement will be measured and paid for separately under relevant item. |
| 38 | 12. Providing and Casting, RCC Precast cover slabs for drainage chambers using Reinforced Cement Concrete of mix 1:1.5:3 ( 1 cement: 1.5 C.S sand : 3 Coarse aggregate)Grade using hard granite graded stone aggregate of 20mm nominal size in volumetric proportions, to the required size, all as per relevant specifications, drawings and as directed includingshuttering, formwork, mixing, transporting, placing, compacting, finishing all the exposed concretein cement mortar1:3( 1Cement : 3 CS sand ) of 12 mm thick to the required finish with addition of super plasticiser at the rate of 100 ml per bag of cement for better bonding and achieving the required strength of plaster, curingwithneat cement punning at 2.2 kg/m2 all as per specification and as directed including lifting handling, transporting and placing the precast slabs over the drainage chambers in correct position and alignment including all materials, labour,tools, plants, equipments, etc., complete. Note: Providing steel reinforcement will be measuredand paid separately under relevant item. |
| 39 | 13.Providing and fixing in position good quality Second Class Teak Wood (such as Dandeli Balarshah or Malabar orequivalent ) wrought Main frames of size 95mm x 58 mm for doors with necessary M.S.hold fasts / clamps fixed suitably to the masonry / concrete including cutting pockets and grouting with Plain Cement Concrete 1:3:6 (1 cement: 3 Crushed Stone sand : 6 hard granite graded stone aggregate of 20mm nominal size) in volumetric proportions, curing including painting with one coat of boiling coal tar paint on the portions of timber abutting against masonry / concrete all as per relevant specifications, drawing and as directed including all materials, labour, tools, equipments etc., complete. |
| 40 | 14.Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws including all labour, materials, tools, equipment, carriage, transport, fuel etc., complete.Note:All fixtures except hinges will be paid separately. |
| 41 | 15. Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. including all labour, materials, tools, equipment, carriage, transport, fuel etc., complete.1. For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.2.Single / double glass panes, wire mesh and silicon sealent shall be paid separately.3. Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) |
| 42 | 16. Providing and fixing factory made uPVC white colour fixed glazed ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.Note:. 1. For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.2.Single / double glass panesand silicon sealent shall be paid separately.3. ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 43 | 17.Supplying Frosted glass sheet of nominal thickness 4 mm (weighing not less than 10 kg/sqm) for window and for louvers for ventilators , fixing in uPVC frames and with necessary clips all as per relevant specifications, drawings and as directed, including all materials, labour, tools etc., complete.Note: The actual area of glass provided alone will be measured for payment purpose |
| 44 | 18. Supplying, fabricating and fixing in position M.S. grills of approved pattern and design for windows, ventilators etc., with necessary M.S. lugs/wall clamps, being fixed to the masonry / concrete portion by cutting pocket of 100 mm x 100 mm size and providing PCC of 1:2:4 mix (1 Cement: 2 Crushed stone sand: 4 hard granite stone graded aggregate of 20 mm nominal size) including making good the disturbed portion all as per relevant specifications, drawing and as directed including priming coat with approved steel primer including necessary cutting, welding, shaping etc., including all materials, labour, transport, tools, equipment, scaffolding, fuel, brushes etc., complete. NOTE: 1.The weighment of the M.S. grill and accessories will be done at site using approved weighing scale in the presence of Engineer\"s assistant. Necessary charges for transport, weighment etc., will be borne by the contractor.2. In case the specified M.S. section is not available in market, the nearest higher alternative section may be used after approval of the Nodal Officer |
| 45 | 19. Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5mm PVC frame strip with PVC solvent cement on the back of the profile.The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer\"s specification and all as directed,including all labour,materials, tools, tackles, equipments, transport, fuel etc., complete. |
| 46 | 20.supplying and fixing 35 mm thick factory made Solid panel PVC Door shutter,Non decorative finish (matt finish) made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer\"s specification including Powder coated M.S. butt hinges 100mm X58mmX1.9mm and all as directed including all labour, materials,tools, equipments , transportation, fixing , etc., completeNote:All fixtures except hinges will be paid separately |
| 47 | 21. Providing and fixing anodized aluminium fittings (Minimum anodic coating of AC 10 grade) for doors, windows, etc., with necessary nuts and screws,all as per relevant specification drawings and as directed including all labour, materials, tools, equipments, etc. complete.21.a Aldrop - 250mm long |
| 48 | 21. b. Tower Bolt 250mm long |
| 49 | 21. C. Draw Bolt 250mm long |
| 50 | 21.d. Door Handle |
| 51 | 21.e. Door Stopper |
| 52 | 22.Providing flooring for toilets with 1st quality conforming to IS : 15622 of approved makeAnti skid ceramic tiles (Johnson or equivalent) of size 300x300mm (or) nearest size of approved pattern and shade, colour,with thickness to be specified by the manufacturer set in C.M 1:4 (1 cement: 4 Crushed Stone sand), 20mm thick and fixing with neat cement slurry @ 3.3 kg/m2 with required slope and joints neatly pointed with white cement added with pigment to match the colour of the tiles, curing, all as per relevant specifications and asdirectedincluding all materials, labour, tools, equipments., etc complete. |
| 53 | 23.Providing 1st quality glazed ceramic wall tiles for dadooing conforming to IS : 15622 of approved make (Johnson or equivalent) of size 300x200mm (or) nearest size of approved pattern and shade, colour,with thickness to be specified by the manufacturer set in C.M 1:3 (1 cement: 3 Crushed Stone sand), 12mm thick and fixing with neat cement slurry @ 3.3 kg/m2 with required slope and joints neatly pointed with white cement added with pigment to match the colour of the tiles, curing, all as per relevant specifications and asdirectedincluding all materials, labour, tools, equipments., etc complete. |
| 54 | 24. Providing flooring in rest shelter/Dalal room and wherever required with first quality VITRIFIED TILES (Marbonite D1 series / Asian/ Italian seriesor equivalent)600mm x 600mm or nearest size as available in the market of 10mm nominal thickness or nearest and set in cement mortar 1:4 (1cement : 4 crushed stone sand) 20mm average thick with required slope fixed with neat cement slurry and joints neatly pointed with white cement added with pigment to match thecolour of the tiles, curing all as directed including all materials, labour, tools, equipments, etc., complete |
| 55 | 25.Preparing the inner surface ofwalls of toilet, rest shelter & dalal room and drainage chambers and providing plaster in cement mortar 1:4 ( 1cement : 4 CS sand of particular gradation) of 12mm thick to the required finish, plastering with addition of super plasticiser at the rate of 100ml per bag of cement for better bonding and achieving the required strength of plaster, curing all as per relevant specification, and as directed including all materials, labour, tools, equipments, etc., complete. |
| 56 | 26.Preparing the outer surface ofwalls of toilet, rest shelter & dalal roomand providing plaster in cement mortar 1:6 ( 1cement : 6 CS sand of particular gradation) of 12mm thick to the required finish, plastering with addition of super plasticiser at the rate of 100 ml per bag of cement for better bonding and achieving the required strength of plaster, curing all as per relevant specification, and as directed including all materials, labour, tools, equipments, etc., complete. |
| 57 | 27.Preparing the ceiling and providing plaster in cement mortar 1:3 ( 1cement : 3 CS sand of particular gradation) of 12mm thick to the required finish for roof and sunshade, plastering with addition of super plasticiser at the rate of 100ml per bag of cement for better bonding and achieving the required strength of plaster, curing all as per relevant specification, and as directed including all materials, labour, tools, equipments, etc., complete. |
| 58 | 28. Preparing the newly plasteredinner surfaces such as walls,ceiling etc.,and Painting with two coats of premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. all asper relevant specifications and as directed includingall materials, labour, scaffolding, tools, equipments, brushes, etc. complete. |
| 59 | 29. Preparing the newly plasteredexterior wall surfacesand Painting with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm of approved colour to give an even shade all asdirected including all materials, labour, scaffolding, tools, equipments, brushes, etc. complete. |
| 60 | 30. Preparing the surfaces of new wooden members and painting with two coats of synthetic enamel paint(Asian or other approved brands) of approved quality including onecoat of primer to give an even shade, all as directed including all materials, labour, scaffoldings, brushes, tools, equipments, etc. complete. NOTE: 1. Necessary painting co-efficient shall be allowed as per Ch.P.T. engineering manual.2.The above quantity is inclusive of painting co-efficient. |
| 61 | 31. Preparing the surfaces of all new steel members and painting with two coats of synthetic enamel paint over a coat of primer (make Asian or equivalent) of approved colour to give an even shade all as directed at site of work including all labour, brushes, materials, tools, tackles, equipments, scaffolding etc., complete.NOTE :1. Necessary painting co-efficient shall be allowed as per Ch.P.T. engineering manual. 2. The above quantity is inclusive of painting co-efficient. |
| 62 | 32. Supplying, transporting, fabricating and placing in position TMT (Fe500 grade or more) steel bars as reinforcements for all RCC works wherever required including all handling, cutting, bending and tying with 1.25 mm dia black annealed steel binding wire all as per specification and as directed including all materials, labour, tools, equipments, etc., complete.Note: The rate shall be inclusive of cost of steel, binding wire and fabrication charge etc., complete. |
| 63 | 33. Providing and fixing good quality flat back (430x260x350 mm or equivalent) urinal basin (white) (New MAGNUM of Parryware or Hindware) as per manufactures’s specification including PVC telescopic flush pipe withclamp, TW plugs ,screws with all fittings and fixtures for inlet and outlet arrangements like spreader, gratings etc all as directed including all materials, labour, tools, tackles, equipments etc., complete. |
| 64 | 34. Providing and fixing granite stone slab with table rubbed, edges rounded and polished of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 CS sand : 4 graded stone aggregate 6 mm nominal size)all as directed including all materials, labour, tools, tackles, equipments etc., complete. |
| 65 | 35. Providing and fixing good quality Indian Water Closet (Orissa pattern - Parryware Or Hindware) glazed white vitreous china of size 580mm x 440mm (overall) or nearest size as available in the marketwith necessary \"P\" or \"S\" trapfixed in 150mm thick brick jelly cement concrete backing of mix CC 1:5:10 (1 cement : 5 crushed stone sand : 10 brick jelly 40mm nominal size), curing and making good thedisturbedportions, includingall fittings and fixtures, etc., all as specified and as directed including all materials, labour, tools, equipments, etc., complete. |
| 66 | 36. Providing and fixing in position of PVC Nahani trap (floor trap) 110mm dia with gratings as available in the market suitable for PVC pipe and embedding the trap in the floor /slab of concrete with suitable gradient making the joints water tight etc., all as directed at site of work including curing, all labour, materials, tools, equipments etc., complete. |
| 67 | 37. Providing and fixing good quality vitreous flat back white wash hand basin 630mm x 450mm size or nearest size as available in the market (Parryware kingsmere basin or equivalent)with a single 15mm C.P. brass pillar tap, C.P. brass waste fitting 32mm dia, C.P. brass union, 15mm dia PVC inlet connection, 32mm dia PVC waste pipe fittings, a pair of cast iron brackets etc as available in the market suitable for fixing the wash hand basin, including painting the brackets etc with two coats of synthetic enamel paint over one coat of primer fixing the brackets with teakwood plug and making good the disturbed portion, etc., all in sound working condition all as per relevant specification and all as directed including all materials, labour, tools, equipments etc., complete. |
| 68 | 38. Providing and fixing 600x450 mm beveled edge face mirror(Saint Gobain or equivalent) of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers etc., allas directed including all materials, labour, tools, equipments, etc., complete |
| 69 | 39.Supplying and fixing C.P.brass towel rail 600mm long with all fittings/fixtures,wooden cleats,CP screws, plugs etc., all as directedincluding all materials, labour, tools, equipments, etc., complete. |
| 70 | 40.Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete all as directedincluding all materials, labour, tools, equipments, etc., complete.40.a. 32mmm dia |
| 71 | 40.b. 25mm dia |
| 72 | 40.c. 15mm dia |
| 73 | 41 Providing and fixing ball valve 15 mm nominal bore (brass) of approved quality, High or low pressure, with plastic floats etrc complete all as directedincluding all materials, labour, tools, equipments, etc., complete.41.a. 15 mm dia |
| 74 | 41.b. 25 mm dia |
| 75 | 42. Supplying and fixing approved quality gun metal wheel valve 32 mm diasuitable forplumbing lines as required including testing the joints etc., all as per relevant specificationand as directed including all materials, labour, tools, equipments, scaffoldingetc., complete. |
| 76 | 43.Providing and fixing approved quality C.P. brass Bib cock 15mm dia including fixing to water pipe lines, making water tight joint etc., including C.P. wall flanges, testing the valves and joints etc., all as specified and as directed including all materials, labour, tools, equipments, etc., complete. |
| 77 | 44. Providing and fixing Semi rigid 32 mm dia PVC waste pipe forwash basin and urinal including P.V.C. waste fittings etc., all as specified and as directed including all materials, labour, tools, equipments, etc., complete. |
| 78 | 45.Providing and fixing rigid unplasticised PVC rain water down take pipes of 110mm dia (Truebore or Finolex or equivalent) ( 4kgf/cm2 ) conforming to IS 13592 with necessary bends, shoes, specials etc., on wall with necessary PVC clamps including fixing clamp, drilling for fixing clamp inclding plugs screws etc, making good the disturbed portions of wall curingincluding joining the pipe with suitable adhesives all as per drawingrelevant specifications and as directed including all labour, materials, tools, equipments,scaffolding etc., complete. |
| 79 | 46.Providing, laying and linking to correct alignments and gradient rigid unplasticised PVC pipes (6kgf/cm2 - Truebore or Finolex or equivalent) for soil waste with necessary tees, bends,coupling, cowls, etc., making connection to the water closets, gully traps, manholes, etc., jointing the pipes and specials using necessary adhesives etc., and making good the disturbed portions all as per relevant specification and as directed, including trenching and refilling including all materials, labours, tools, equipments, etc., complete. NOTE:The rate is to include the cost of cutting the masonry to the required size for taking the PVC pipe including making good the disturbed portion.46.a. 75 mm dia Pipe |
| 80 | 46.b. 110 mm dia Pipe |
| 81 | 47.Providing 52 mm thick cement concrete flooring with concrete hardener topping,under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 CS sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer\"s specifications. This includes cost of cement slurryetc. complete all as specified and as directed including all materials, labour, tools, equipments, etc., complete. |
| 82 | 48.Providing raised band 100 mm wide, 12 mm thick inplain cement mortar 1:4 (1 cement : 4 CS sand) to the required finish with addition of super plasticiser at the rate of 100ml per bag of cement for better bonding and achieving the required strength of plaster, curing all as per relevant specification, and as directed including all materials, labour, tools, equipments, etc., complete. |
| 83 | BILL No;3SUPPLY AND INSTALLATION OF HIGH MAST TOWER |
| 84 | 1. Charges for design, transportation to site and supply 30M high mast tower comprising of theHigh mast structure complete, Aviation luminaries, Lightning finial and Local fibre glass feeder panel for high mast with timer panel as detailed in relevant schedule |
| 85 | 2. Charges for providing foundation for the erection of 30M high mast tower. |
| 86 | 3.Cost of erection over the corresponding foundation of 30M high mast. |
| 87 | 4. Supply and installation 400 W, LED Flood light fitting with all other accessories as per relevant schedule4.a. Supply |
| 88 | 4.b. Instaltion |
| 89 | 5. Cost of cabling, trials, testing, commissioning, and handing over of 30M high mast. |
| 90 | 6. Supply and Installation of Main fibre glass feeder pillar box as detailed in relevant schedule6. a. Supply |
| 91 | 6.b. Installation |
| 92 | 7.Supplyand laying of 3 ½ core 50 sq. mm L.T under ground cable of 1100V galvanized steel strip armoured XLPE cable with stranded Aluminium conductor conforming to IS. 7098 Part I with latest amendments from Main feeder pillar to each high mast feeder pillar.7a. Supply |
| 93 | 7b.. Laying |
| 94 | 8. Supplyand laying of 3 ½ core 25 sq. mm L.T under ground cable of 1100V galvanized steel strip armoured XLPE cable with stranded Aluminium conductor conforming to IS. 7098 Part I with latest amendments from Main feeder pillar to High mast Tower8.a. Supply |
| 95 | 8.b. Laying |
| 96 | 9. Supply and laying of 3 core 2.5 sq. mm copper cable of 1100V from Junction box at each high mast light fitings9a. Supply |
| 97 | 9.b. Laying |
| 98 | 10. Provision of Maintenance freeearthing, GI Flat & wires for high mast towers as detailed in relevant schedule.10.a. Supply |
| 99 | 10.b. Installation |
| 100 | BILL No;4Providing CCTV for Goods shed yard |
| 101 | 1. Supply of 8 Channel Network Video Recorder complete with 4 TB Hard Disk and all accessories as detailed in the relevant schedule |
| 102 | 2.Supply of 4 MP Network IR Bullet Cameras complete with all accessories as detailed in relevant schedule |
| 103 | 3.Supply of 8 Port 10/100 POE switchall accessories as detailed in relevant schedule |
| 104 | 4.Supply and fixing of OFC media converterall accessories as detailed in relevant schedule |
| 105 | 5.Supply of 21 inches LED Monitorall accessories as detailed in relevant schedule |
| 106 | 6.Supply of 4U Rack with power managerall accessories as detailed in relevant schedule |
| 107 | 7.Supply and laying of armoured 6 core OFC cable with all material and accessories |
| 108 | 8.Supply and laying of armoured 3 core, 1.5 sqmm armoured power cable with all accessories |
| 109 | 9.Supply and laying of CAT 6 network cable with all required materials |
| 110 | 10.Charges for Installation and Commissioning |
| 111 | BILL No;5Providing electrical works for Ancilary Structures. |
| 112 | 1. Supply and installation of surface type Tube light fitting suitable for 220V, AC. 4 feet, 18 watts LED Fittings with LED Tubelight with life of the fitting is not less than 30000 burning hours. Lumen out put is not less than 100 lm/watt.1.a. Supply |
| 113 | 1.b. Installation |
| 114 | 2. Ceiling fixture 250 / 300mm complete with gallery, etc., clear glass opaque / crystal with9Watts / 12Watts LED Bulb.2.a. Supply |
| 115 | 2.b. Installation |
| 116 | 3. Water tight type Bulb head fitting with9Watts / 12Watts LED Bulb with guardheavy duty type.3.a. Supply |
| 117 | 3.b. Installation |
| 118 | 4. Supply and installation Ceiling fan of 1200 mm (48”) sweep, brown colour, double ball bearing at operating voltage of 230V AC. with suitable down rod for fixing without Regulatora. Supply |
| 119 | 4b. Installation |
| 120 | 5.Supply and installation of 12” size of exhaust fan with necessary clamps, bolts and nuts at operating voltage of 230V AC.a. Supply |
| 121 | 5.b. Installation |
| 122 | 6. Supply of all materials and accessories and carrying out the surface/concealed conduit wiring by using suitable size of PVC / G.I. with 2 runs 2.5 sq.mm and one run of 1.0 Sq.mm PVC insulated unsheathed copper conductor wires from LDBto SSB. |
| 123 | 7. Supply of all materials and accessories and carrying out the surface/concealed conduit wiring by using suitable size of PVC/case and capping with 2 runs 1.5 Sq.mm and one run of 1.0 Sq.mm, PVC insulated unsheathed copper conductor wires for fans, light fittings etc, through connected junction/ inspection boxes along with modular flush type control switch along with base plates and ceiling rose including terminations wherever necessary from modular type sub switch board to individual points. |
| 124 | 8. Supply and installation of all materials and accessories of 5Amps switch and socket outlet to be mounted in the modular type sub switch board itself including the supply of 5Amps modular switch and socket outlet with control switch and base plates and wiring to the plug for allfloorsa. Supply |
| 125 | 8.b. Installation |
| 126 | 9. Lighting Distribution board with suitable way comprising of 1 No. 63A, DP, MCB as incomer, 3 Nos. 32A SP MCB and 9 Nos.16A SP MCBas outgoing along with suitable copper wires/busbars for each phase and neutral along with all other components and accessories as per relevant schedulea. Supply |
| 127 | 9.b. Installation |
| 128 | 10. Providing of Maintenance free Earthingas detailed in relevant schedule10.a. Supply |
| 129 | 10.b. Installation |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
