|
| 1 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/by mechanical means including stacking of pipes within 50 meters lead as per direction of Engineer-in-charge : Above 40 mm nominal bore |
| 2 | Dismantling D.I pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/by mechanical means including stacking of pipes within 50 meters lead as per direction of Engineer-in-charge : 150 mm dia. |
| 3 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed:All kinds of soil :1 meter from cutting edge. |
| 4 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:All kinds of soil : |
| 5 | Laying in position centrifugally cast (spun) iron S&S or flanged pipes (excluding cost of pipe): |
| 6 | Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes orDuctile Iron Pipes including testing of joints and including the cost of rubber gasket. |
| 7 | 300 mm dia |
| 8 | 250 mm dia |
| 9 | 200 mm dia |
| 10 | 150 mm dia |
| 11 | 100 mm dia |
| 12 | Laying and fitting of G.I. pipes (all classes) complete excluding cost of pipes, fittings and Earth work. 50 mm dia. G.I. pipes.100 mm dia. G.I. pipes.Salvaged |
| 13 | Laying and fitting of G.I. pipes (all classes) complete excluding cost of pipes, fittings and Earth work. |
| 14 | 20 mm dia. nominal bore |
| 15 | 25 mm dia. nominal bore |
| 16 | 40 mm dia. nominal bore |
| 17 | 50 mm dia. nominal bore |
| 18 | 65 mm dia. nominal bore |
| 19 | 80 mm dia. nominal bore |
| 20 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete |
| 21 | 25 to 40 mm nominal bore |
| 22 | 50 to 80 mm nominal bore |
| 23 | Providing & fixing ofM.S Flanges 12mm thick including cost , nuts, bolts, washers and all sorts of carriages involved up to the site of work. Complete job. |
| 24 | 80 mm dia |
| 25 | 100 mm dia |
| 26 | 150 mm dia |
| 27 | Providing and fixing C.I. sluice valves (with cap) complete nuts, rubber insertions etc. (the tail pieces if required will be paid separately). |
| 28 | 100 mm dia. (Class I) |
| 29 | 150 mm dia. (Class I) |
| 30 | 200mm dia (Class I) |
| 31 | 250mm dia (Class I) |
| 32 | 300 mm dia.(Class I) |
| 33 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc. if required will be paid separately).50 mm dia. |
| 34 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) |
| 35 | 65 mm nominal bore |
| 36 | 80 mm nominal bore |
| 37 | Manufacturing/ fabrication and fixing of M.S surface box/chambers of size (0.60x0.60x0.75m) made out of 6mm thick MS sheet using 40x40x5mm angle iron for frame including cutting, hoisting and fixing in position incl. all locking arrangements, handles hinges etc and applying priming coat of approved steel primer. The job includes providing andlaying of cement concrete 1:2:4 on the base of frame to be embedded in, including all sorts of carriages involved for the completion of the job. The job is to carried out as per the directions of Site-incharge.complete job. |
| 38 | Providing of FHTCs to every unconnected household including cost of 15mm to 20mmdia G.I pipe for a length of 6 to 20 mtrs with G.I fittings /specials incl. laying & fitting of pipes ,earth work in excavation andrefilling.The job includes providing and fixing of Water Meters. complete job. |
| 39 | Supplying,Installation,Commissioning and Testing of Electromagnetic Flow Meters of ISI/ reputed Make (.The item includes fabrication of M.S tail pieces,flanges ,nuts bolts,R.I cloth etc, cutting of existing supply line,welding,wiring from panel board to site of installation complete as per requirement of site incl cost of RCC protective chamber of suitable size incl cost of M.S covers,ladders etc .complete job. |
| 40 | 200 mm dia |
| 41 | 150 mm dia. |
| 42 | 100 mm dia. |
| 43 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.All kinds of soil : |
| 44 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.All kinds of soil : |
| 45 | Providing & laying of stone soling hand packed in trenches.(Nallah) |
| 46 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 47 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. Allworks upto plinth level:1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 48 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement:1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 49 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering,finishing and reinforcement with: 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 50 | Reinforced cement concrete work in arches, archribs, domes, vaults shells, folded plate and roofs having slope more than 15° upto floor five level level including curing but excluding the cost of centering, shuttering finishing and reinforcement with: 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 51 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: |
| 52 | 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) |
| 53 | 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 54 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 55 | Foundations, footings, bases of columns etc. for mass concrete. |
| 56 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc |
| 57 | Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 58 | Arches, domes, vaults upto 6 m span |
| 59 | Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 60 | Suspended floors, roofs, landings, balconies and platform |
| 61 | Edges of slabs and breaks in floors and walls. Under 20cms wide |
| 62 | Stairs, (excluding landings) except spiralstaircases. |
| 63 | Extra for shuttering in circular work (20% of respective centering and Shuttering items). |
| 64 | Foundations, footings, bases of columns etc. for mass concrete. |
| 65 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc |
| 66 | Lintel, beams, plinth beams, girders, bressumers and cantilevers. |
| 67 | Extra for arches, domes, vaults exceeding 6 m span |
| 68 | Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 69 | Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and de-centering at all levels, over a height of 3.5 m, for every additional height of 1 meter or part thereof (Plan area to bemeasured). Suspended floors, roofs, landings, beams and balconies (plan area to be measured) |
| 70 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level: Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 71 | 12mm Cement plaster finished with a floating coat of neat cement of mix:1 : 3 ( 1 cement : 3 fine sand) |
| 72 | 12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) |
| 73 | Demolishing cement concrete manually/by mechanical means includingdisposal of material within 50 meters lead as per direction of Engineer-incharge:1:3:6 or richer mix (i/c equivalent design mix) |
| 74 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 75 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 76 | Structural steel work in built up sections, trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.Welded |
| 77 | Providing & fixing of ventillator/lighting arrangement on the top of dome of size(0.50x0.50 m) with 40x40x5mm angle iron base frame of 1m height fitted with 3mm mesh and fibre glass around the base incl. all ffittings and fixtures and all sorts of carriages involved for the completion of job.complete job. |
| 78 | Providing & fixing of main hole cover with iron base made up of angle iron (50x50x5mm) & lid of 40x40x5mm angle iron fitted with 6mm thick M.S plate .complete job. |
| 79 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts,bolts and washers as required complete as per the direction of Engineer-incharge.Made of G.I. wire of dia 4 mm |
| 80 | Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.50 mm thick with zinc coating not less than 275 gram/m2 |
| 81 | Providing ridges or hips of width 60cm overall width plain G.S. sheetsfixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I.limpet and bitumen washers complete. 0.50 mm thick with zinc coating not less than 275 gram/m2 |
| 82 | Providing/Fabricating,, fixing of M.S fittings viz bends, Tees,nipples double collars, tail pieces of suitable degrees to be fabricated from 6mm/8mm thick M.S plate as per the requirement of site. This item also includes cost ofspun yarnwith insertion of spun yarn including welding charges,cutting,threading ends etc. The work should be leak proof . The job is to be paid in fitted and finished form and is to be carried out as per the directions of site in charge.complete job. |
| 83 | Brick work with common burnt clay F.P.S. (non-modular) bricks of class designated 75 in superstructure in Cement mortar 1:4 (1 Cement : 4 Fine sand). |
| 84 | Extra for brick work in superstructure above plinth level upto floor V level. (By manual means) |
| 85 | ProvidingAluminium workin frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position with hold fast lugs or with dash fastners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately). First class kail wood. |
| 86 | ProvidingAluminium work Shuttersof doors, windows, clerestory windows and other frames wrought framed and fixed in position with hold fast lugs or with dash fastners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately). First class kail wood. |
| 87 | Providing and fixing glazing in aluminum door, window, ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasket etc.complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic item.)22.3.1 With floating glass panes of 4.0 mm thickness (weight not lessthan 10.00 kg / sqm)22.3.2 With float glass panes of 5.0 mm thickness (weight not lessthan 12.50 kg / sqm) |
| 88 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer\"s specification. |
| 89 | Providing /fixing of 150 mm dia MS Tail piece with paddle flange & end flange of length 1.20 metres (Subject to actual at site). |
| 90 | Providing /fixing of falnged jointedto 150 mm dia G I Ppipe incl all nuts, bolts washers etc.COMPLETE JOB |
| 91 | Providing /fixing of 65 mm dia thick constant bleed with requisite bends, ball valves, erecting with assembly complete job (Subject to actual at site). |
| 92 | Providing /fixing of 150 mm dia MS pipe flanges incl. requisite supporting from floculator to filter house channel (Subject to actual at site). |
| 93 | Providing, fixing, installation, sucessful commissioning of up rotating bridge moving with MS rail on center bearing incl. embedding in cement concrete and on the base of clarifloculator & fabricated with ISA-100x100x6mm channel with 50x50x6mm angle, suitable for bearing silt load incl. end carriage driver, fly wheel, chain reduction gear motor of required base frame with PGI cover for reduce gear & motor, MS wheel for bridge to facilitate incl. pinion bearing shaft, incl. 3 phase circuit assembly for rotation of floculator bridge, MS wheel and arrangement motors etc. of 1.5 HP moving arrangement crompton make reduction gear box frame stainless steel blades. the job also incl. connecting pole system & appropriate gauge PVC, copper wire & electric cables, all complete job. |
| 94 | Providing/Laying of filter media supported by requisite sizes of gravel incl. all carriages, head load & placing in position, all complete job. |
| 95 | Marble stone flooring with 16 mm (average) thick marble stone (sample of marble shall be approved by engineerin-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with cement slurry including rubbing and polishing complete with: pink plain marble. |
| 96 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades, except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 97 | Finishing walls with water proofing cement paint of required shade: New work (two or more coats) applied @3.84 kg/10 sqm. |
| 98 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including priming coat with cement primer. |
| 99 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work. |
| 100 | Providing/fixing of 80 mm dia PVC drainage system with specified perforation with requisite tees, plug caps, laying in position all complete job. |
| 101 | Providing ridges or hips of width 60 cm overall width plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gm/m2 |
| 102 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer:Using M.S. angles 40x40x6mm for diagonal braces |
| 103 | Providing/fixing/testing/commissioning of 1 HP motor reduction gear box vertical fledges, agitator, 40 mm dia line for above at bleaching chambers, GM values, PVC disphrase valves ridged PVC pipes M/S rubber lined above tank all complete job. |
| 104 | Providing and fixing gun metal non-return valve of approved quality(screwed end):65 mm nominal bore |
| 105 | Providing ,installation and fixing of 5HP submersible pumping unit of ISI/Reputed make incl. cost of electrical wiring/cables,control switches,pipe work ,fittings,specials and insulation incl cost of all accessories incl voltage stablizer of required capacity.complete job. |
| 106 | Providing/fixing/testing/commissioning of centrifugal pumping set with discharge along with all connecting accessories, 2 HP 3 phase electric motor 50 mm GI piping with specials GM foot valve, non return valve coupling level indicator for back wash tank incl requisite concrete base with nut bolts all complete job. |
| 107 | Providing/fixing/testing/commissioning of150 mm dia sluice valves incl. bends, tees, tail pieces all complete job. |
| 108 | Providing/fixing/testing/commissioning of air blower complete with all requisite accessories, concrete base, nuts, bolts, washers, 65 mm dia GI pipe with requisite valves with a standby unit all complete job. |
| 109 | Providing/fixing of extension rods for sluice valves incl. housing, fixing in concreteall complete job. |
| 110 | Providing/fixing/testing/commissioning of Rate of flow, MS surface floats, loss of head gauge, filter modules, MS surface floats, flow meters and glass tops for CWC. |
| 111 | Providing and installation of 19/18 PVC copper main cable connection from transformer to treatment plant of reputed make ISI as per the requirement of department. |
| 112 | Providing 3 phase c/c circuit connection for electric motors with insoluble cables capacity variying for 1 to 5 HP. |
| 113 | Providing main control pannel board incl. cabling, light indicator, circuit monitoring, boxing, angle iron, embedding in walls, makin good the same as per engineer-in-charge. |
| 114 | Providing and installation of voltage stablizers of 20 KVA capacity conforming to relevant IS specification. |
| 115 | cost on account creationof 100kva sub station and 11kv feeder with 9.0m long SP-33 ST poles fitted with sole plates cross arma, insulatior, pins, link sets. Dropouts sets disc sets, lighting areestors concerte bottiming as site requirement. |
| 116 | cost on account of 50kva voltage corectionequipment. |
| 117 | cost on account of fire fighting eqipument shock proof matting and other electric item as preventive measures |
| 118 | cost on account of electrification of premisses and pump house by way of high mist lumumminaries incld. Cost MS tubuler poles and other allied asseceriores and conductors |
| 119 | cost on account of providing, fitting of automatic power factor correcton pannel with allied jobs. |
| 120 | cost on account of tools and tackles, shock resistant rubbar mats, anti skid rubber flooring, matting, bedding for operators etc |
| 121 | Demolishing cement concrete manually/by mechanical means includingdisposal of material within 50 meters lead as per direction of Engineer-incharge:1:3:6 or richer mix (i/c equivalent design mix) |
| 122 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):First class kail wood |
| 123 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.35mm Thick.First class kail wood |
| 124 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40mm thick.First Class kail wood |
| 125 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :First class kail wood.35mm thick |
| 126 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS:15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown |
| 127 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades, except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 128 | Providing and installation of water Geyser 50 ltrof reputed make Like Havells/Recold/Venus, incl nuts bolts ,and all sanitary fittings ,angle valves,cp connections etc complete job. |
| 129 | Providing ,installation and fixing of 1HP water motor of ISI/Rputed make incl. cost of electrical wiring,control switches,pipe work ,fittings,specials and insulation.complete job. |
| 130 | Providing & fixing White vitreous china water closet squatting pan(Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.Orissa pattern W.C Pan of size 580x440 mm |
| 131 | Providing and fixing of wash basin vitreous china of ISI mark incl cost of fittings and brackets,incl cost of waste pipe , angle valves,cutting and making good the walls whereever required.(450 x 300 mm). |
| 132 | Providing and fixing of salem stainless steel kitchen sink of ISI mark 304 (18/8) as per IS 13983 with C.I brackets and S.S plug 40mm incl painting of fittings and brackets,incl cost of waste pipe ,cutting and making good the walls whereever required.(610x510x200mm). |
| 133 | Providing offixing of sanitary items as under: |
| 134 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.:15 mm dia. nominal bore |
| 135 | Providing and fixing brass bib cock of approved quality.15 mm nominal bore |
| 136 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 |
| 137 | Providing and fixing 15 mm nominal bore of standard back type C.P.brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg. |
| 138 | Providing & fixing of sanitary items like,, a soap case anda towel rod,holders,Mirror with mirror shelf incl cost of screws etc complete job . |
| 139 | providing of lighting electric points incl. Cost of wiring,earthing,switches, MCBs,LED Luminaries and cost of wiring from 1.5mm thick PRF Coil.(all the items should confirm to the IS codes from reputed manufacturer such as Havells/L&T/Polycab/Legrand.complete job. |
| 140 | Providing,installation and testing of heating pointsincl. Cost of wiring,earthing,switches, MCBs, switch boards and all accessories cost of wiring from 1.5mm thick PRF Coil.(all the items should confirm to the IS codes from reputed manufacturer such as Havells/L&T/Polycab/Legrand.complete job. |
| 141 | providing of 10mm thick service line of reputedmake:Havells/L&T/Polycab/Legrand. |
| 142 | Providing & Fixing ofhardware items like hinges,handles tower bolts of ISI Make for doors & ventilators incl cost of screws etc.complete job.. |
| 143 | Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank |
| 144 | construction of Soakage pit 10 mtrs deep, one mtr Diameter includingproviding /fixing of pre cast reinforced concreterings and top precast coverat site as per the satisfaction of Engineer In charge.complete job. |
| 145 | P/f of heavy qualityPVC fittings of ISI Mark (prince Make) of 100mm dia forpantry/bath rooms/latrine complete incl. bends traps, P-traps ,pipe upto septic tank/ soakage pit.complete job. |
| 146 | Providing & incorporating water bar at construction joints to make them leak proof.complete job. |
| 147 | Providing & laying of HDPE pond lining on the bed & walls of 500gsm thickness incl. cost of welding of joints & overlaps.complete job. |
| 148 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 149 | Carriage of material fromsource uptosite of work by mechanical means incl. loading, unloading and stacking complete. |
| 150 | cement & steel an avg. lead of 10kms. |
| 151 | Sand &Stone aggregates for an avg. lead of 45 kms. |
| 152 | Stone soling for an avg. lead of 20km |
| 153 | Stone soling for an avg. lead of 15 km |
| 154 | Bricks 45km |
| 155 | 300 mm dia D.I PIPES 10KM |
| 156 | 250mm dia D.I pipe from divl store lead 20km |
| 157 | 200mm dia D.I pipe from divl store lead 20km |
| 158 | 150mm dia D.I pipe from divl store lead 20km |
| 159 | 150mm dia D.I pipe from divl store lead 10km |
| 160 | 100mm dia D.I pipe from divl store lead 10km |
| 161 | 100mm dia D.I pipe from divl store lead 20km |
| 162 | Below 100m dia G.I pipes 20km |
| 163 | Below 100m dia G.I pipes 10km |
| 164 | 200mm dia D.I pipe from divl store lead 10km |
| 165 | 150mm dia D.I pipe from divl store lead 4km |
| 166 | Extra Carriage of material fromdumping site to actualsite of work by manual means (Head load) for an avg lead of 2250 mtrs. |
| 167 | cement |
| 168 | steel |
| 169 | Sand &Stone aggregates |
| 170 | Stone soling |
| 171 | 300 mm dia D.I PIPES 200 mtr lead |
| 172 | 250mm dia D.I pipe 2000 mtr lead |
| 173 | 200mm dia D.I pipe 4000 mtr lead |
| 174 | 150mm dia D.I pipe 3000 mtr lead |
| 175 | 150mm dia D.I pipe 2000 mtr lead |
| 176 | 150 mm dia D.I PIPES 200 mtr lead |
| 177 | 100 mm dia D.I PIPES 200 mtr lead |
