|
| 1 | Excavation carefully by manual means up to 2.00 mtr. Depth without damaging the buried architectural parts of the monument/structure and stacking all the intact parts at proper place for reuse at the time of restoration work as per direction of Engineer in-charge with in 50mtr.lead. |
| 2 | Lime Sand Mortar 1:2 (1 Lime putty : 2 Sand) including preparation of mortar by traditional practice (by grinding) |
| 3 | Cément Sand Mortar 1:3 (1 Cément : 3 Sand) |
| 4 | Making Mehrab\"s, Arches, pillars, highly decorative creepers, flower of small sizes etc.in lime Surkhi plaster (1:2) as per B248old traditional practices (Arches, Mehrab\"s) in three coats for base course and subsequent course and Loi tamping, beating till the shrinkage cracks are disappear than making ornamental flowering/design etc. The work is to done with all leads and lifts as per work of restoration nature as per Jaipur practice. |
| 5 | Flush and ruled pointing in Cement Mortar 1:3 over joints of dressed stone cladding, chajjas, jali etc.withcement, sand & colour including racking the joints as per traditional practice including all leads and lifts |
| 6 | Flush and ruled pointing over joints of dressed stone cladding, chajjas, jali etc.including racking the joints as per traditional practice including all leads and lifts with grinded mortar of lime putty and fine sandmixed in 1:2 ratio and gur, methi, gugal etc. are to be mixed as per traditional practice |
| 7 | Khamira Colour Washing as per old traditional practice to prepare the Khamira the lime should be slaked at least for 7-10 days and regularly it should be stirred by adding cured, Gugal, for nonsynthetic colour adding gum (babool gum) as per specification. Then applying prepared solution on walls three to four thin coats as desired finishing. |
| 8 | Stucco work in lime, Surkhi, mortar (1:2) as per existing design work/ traditional practices by skilled craftsman, the stucco work should be done as per restoration nature, the mortar should be prepared by grinding milladding gur, methi & gugal.. The thickness varies from 50 mm to 100mm as per the design (minimum rectangular surface area to be measured). |
| 9 | Removing of old lime plasterup to 75 mm thick in patches with height up to 4.5 m. Disposal up to 100 meter lead |
| 10 | Scraping & Removing of white wash/ distemper/oil paint/algli etc. from lime plaster highly decorative, ornamental and stucco work with at most care by using fine sand paper under the close supervision to keep intact the old designs. |
| 11 | Providing and fixing stone Patties (slab) on roofing including removing broken patties carefully and replacement new slab with Kharanja, ralthal and lime dhar as per traditional practice. Span about 3.30 mtr. To 5.50 mtr. 100 mm to 150 mm thick of approved stone. |
| 12 | Painting on Stucco work with stone colours including base coat of khameera as per traditional practice (minimum rectangular to be measured). |
| 13 | Rubbing / removal of lime plaster on stone works by abrasive methodUp to 1” thick layer |
| 14 | Water proofing with consolidation of basic substrata, making it complete water proof with Protekta series of compounds or equivalent as per manufacturers specifications and as per direction of engineer in charge |
| 15 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compoundconsisting of applying : a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. b) laying second layer ofFibre glass cloth when the first layer is still green.Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm.This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entiretreatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. d)fourth and final layer ofbrick tiling with cement mortar (which will be paid for separately For the purpose of measurement the entire treated surface will be measured. |
| 16 | Washed stone grit plaster on exteriorwalls of height upto 10 M. above level in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg ofcement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement : 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in- charge (Payment for providing grooves shall be made separately). |
| 17 | Extra for plastering done on moulding cornices or architraves including neat finish to line and level: In one coat |
| 18 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer. |
| 19 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 20 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. G.I. pipes. |
| 21 | Providing and erecting direction and place identifications retroreflctrorised sign as per IRC:67 made of high intensity grade sheeting vide clause 807.3, fixed over aluminium sheeting 2 mm thick supported on mild steel angle iron post 75 x 75 x 6 mm firmly fixed to ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing. Identification sign board of size upto 0.90 sqm |
| 22 | Painting new letters and figures of specified size, of any shade with first quality synthetic enamel paint, black or any other approved colour to give an even shade as per clause 801 of MoRT&H Specification including all material, labour. Hindi (Matras, Commas and the like not to be measured and paid for. Half letters shall be counted as half). |
| 23 | Random rubble masonry with hard stone in foundation and plinth : Extra for random rubble masonry with hard stone in : Circular pillars. |
| 24 | Random rubble masonry with hard stone in foundation and plinth : Extra for random rubble masonry with hard stone in superstructure above plinth level and upto two stories. |
| 25 | Random rubble masonry with hard stone in foundation and plinth : Cement mortar 1:3 (1 cement : 3 coarse sand) |
| 26 | Brick work with FPS bricks of class designation 75 infoundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 27 | Half brick masonry with FPS bricks of class designation 75 in superstructure above plinth level upto two stories. Cement mortar 1:3 (1 cement :3 coarse sand) |
| 28 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 29 | Stone tile work for wall lining upto 10 m height with special adhesive over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement with an admixture ofpigment to match the stone shade. 8mm thick (mirror polished and machine cut edge) Granite stone of any colour and shade |
| 30 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 31 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills,fillets etc. upto two stories, excluding the cost of centring, shuttering and finishing : 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 32 | Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars |
| 33 | Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above plinth level including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 34 | Stone work (machine cut edges) for wall lining etc. (veneer work) backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of cramps which shall be paid for separately) : Red sand stone - Exposed face fine dressed with rough backing 70 mm thick. |
| 35 | Stone work ( machine cut edges) for wall lining upto 10 m height etc. (Veneer work) backing filled with a grout of 12mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust) including rubbing and polishing complete. (To be secured to the backing by means of cramps which shall be paid for separately) Kota stone slabs exposed face dressed and rubbed. 25mm thick |
| 36 | Stone work in plain ashlar in super structure upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 whitecement : 2 stone dust) with an admixture of pigment matching the stone shade : One face dressed. Red sand stone |
| 37 | Both face dressed. White sand stone |
