Military Engineer Services-MES has published Repairs To Flooring, Joinery, Ac Sheeting, False Ceiling And Certain Miscellaneous Repairs At Zone B Area Of Old Cantt Allahabad. Repairs To Flooring, Joinery, Ac Sheeting, False Ceiling And Certain Miscellaneous Repairs At Zone B Area Of Old Cantt Allaha. Submission Date for this Tender is 16-11-2021. Civil Work Tenders in Allahabad Uttar Pradesh. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 10-Nov-2021 | Amendment in Sch of Credit | Other | 16-11-2021 |
| Sl. No. | Item Description |
| 1 | Demolition of Concrete work (un-reinforced)in ground floors and pavings including floor tiles not exeeding 15 cm thickness (below or above ground level) and removal of debris from the site, complete all as specified and directed. |
| 2 | Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including cutting of reinforcement to facilitate demolition, complete all as specified and directed. NOTE:- The reinforcement obtained out of demolition shall be deposited in the AGE B/R storeyard and shall be taken into charge by the department duly entering into the salvage register. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding, removing rubbish off the premises,complete all as specified and directed. |
| 4 | Dismantling Stone slabs laid and pointed in cement mortar of any description or thickness in floors, aprons etc. complete all as specified and directed. |
| 5 | Taking down cement plaster on brick or stone walls or wall tiles etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish off the premises, complete all as specified and directed. |
| 6 | Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed. |
| 7 | Non-skid ceramic coloured jointless tiles 7 to 8 mm thick, size of tiles shall be 300mm x 300mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with and including provision of 15mm thick screed bed in CM 1:6,complete all as specified and directed. |
| 8 | Glazed ceramic coloured tiles as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 300mm x 200mm x 6mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laidover and including provison of 10 mm thick backing coat in CM 1:4, complete all as specified and directed. |
| 9 | Glazed ceramic coloured tiles as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 300mm x 450mm x 6 to 7mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laidover and including provison of 10 mm thick backing coat in CM 1:4, complete all as specified and directed. |
| 10 | Non - skid ceramic coloured jointless tiles 7 to 8 mm thick, size of tiles shall be 400mm x 400mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with and including provision of 15mm thick screed bed in CM 1:6,complete all as specified and directed. |
| 11 | Non - skid ceramic coloured jointless tiles 7 to 8 mm thick, size of tiles shall be 400mm x 400mm, as in vertical surfaces such as skirting / dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 10mm thick backing coat in CM 1:4,complete all as specified and directed. |
| 12 | Vitrified Ceramic coloured tiles 8 to 10 mm thick, size of tiles shall be 600mm x 600mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with and including provision of 15mm thick screed bed in CM 1:6,complete all as specified and directed. |
| 13 | Non - skid ceramic coloured jointless tiles 8 to 10 mm thick, size of tiles shall be 600mm x 600mm, as in vertical surfaces such as skirting / dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 10mm thick backing coat in CM 1:4,complete all as specified and directed. |
| 14 | Pre-polished rubber molded smooth- finish, exterior, designed, pre-cast interlocking tiles / pavers, 60 mm thick laid over and including provisin of 25mm thick sand cushioning, complete all as specified and directed. |
| 15 | Exterior Heavy duty full body coloured paving tiles of size 300mm x 300mm x 8 to 9 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including provision of 15 mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed. |
| 16 | Machinecut Granite 20 mm thick table rubbed and polished counter top, cooking plateform bedded and jointed with grey cement slurry and pointed with white cement mixed with admixture of pigment to match the shade of granite including cutting, polishing and moulding edges, with and including provision of 15 mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed. |
| 17 | Machine cut Baroda Green marble stone slab 18 to 20 mm thick laid over Kitchen cooking platform over and inclujding provision of 20 mm thick cement screed bed in CM 1:6, laid and jointed in grey cement slurrry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete and including nosing of the edges half round, complete all as specified and directed. NOTE:- Stone slab shall fixed in two pieces of appropriate size as per site requirement. |
| 18 | Machine cut Kota stone slab 18 to 20 mm thick as in flooring, laidover and including provision of 20 mm thick screed bed in cement mortar 1:6, laid and jointed in grey cement slurry mixed with pigment to match slab including rubbing and polishing to mirror finish, complete all as specified and directed. |
| 19 | Machine cut Kota stone slab 18-20 mm thick laid over and including provision of 10 mm thick backing coat in CM 1:4 as in riser of steps, skirting, pillar etc., laid and jointed in neat cement slurry mixed with colouring pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed. |
| 20 | Cement concrete 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in floors, 25 mm thick, complete all as spcified and directed. |
| 21 | Cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in plinth protection, 50 mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at the length not exceeding 3 metres and at every change of direction and filling the same with and including provisin of bitumen and sand in proportiioin of 1:3 by weight, complete all as specified and directed. |
| 22 | PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), 75 mm thick, as in sub base of floors etc., complete all as specified and as directed. |
| 23 | Cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floors, 40 mm thick, laid in panels fixed with glass dividing strips and finished even and smooth using extra cement, complete all as specified and directed. NOTE:- Glass dividing strips shall be measured and paid as "Supply only" separately under respective item of this Schedule. |
| 24 | Supply only Glass dividing strips, 3 mm thick and 38 mm wide, inserted in position, in floors, complete all as specified and directed. |
| 25 | PCC 1:2:4 type B-2 (40 mm graded stone aggregate), 100 mm thick, as in floors laid in alternate panels including use and waste of necessary form work, finished even and smooth without using extra cement, complete all as specified and directed. |
| 26 | Precast reinforced cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregate) as in cover slabs, etc.,set in cement mortar 1:4, with and including provisin of necessary formkwork, complete all as specified and directed. NOTE:- Reinforcement shall be measured and paid separately under respective item of this Schedule. |
| 27 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. |
| 28 | Brick work with sub class "B" Bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius, built in cement mortar 1:6, complete all as specified and directed. |
| 29 | Brick work with sub class "B" Bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius, built in cement mortar 1:6, except bricks, complete all as specified and directed. |
| 30 | Rendering 15 mm thick on brick work or concrete surface in cement mortar 1:4 as in drain, boundary wall etc., finished even and smooth without using extra cement, complete all as specified and directed. |
| 31 | Rendering 15 mm thick on brick work or concrete surface in cement mortar 1:4 mixed with water proofing compound (excluding), surface finished even and smooth, including provision of two coat of cement base paint over a coat of cement primer after preparation of new plastered surfaces of walls, complete all as specified and as directed. NOTE:- Water proofing compound shall be measured and paid separately as "supply only" under respective item of this Schedule. |
| 32 | Rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth complete. |
| 33 | Rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished fair and even, complete all as specified and directed. |
| 34 | Supply only integral water proofing compound, complete all as specified and directed. NOTE:- The water proofing compound shall be ISI marked and approved make as specified here-in-after and shall be incorporated in the work all as per manufacturers instructions. |
| 35 | Plain Cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in roof kerbs, mud stops or chamfered on edges all as directed including provision of necessary form work, complete all as specified and directed. |
| 36 | Cleaning the sunken floor surfaces by wire brushes, brooming, removing dust, including dismantling of floor, lime terracing and applying following :- (a) Bitumen primer confirming to IS-3384-1965 @ 0.50 kg per sq.m. (b) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS – 702-1998 for water proofing membrane. (c) Applying of polymeric water proofing membrane weight not less than 3 kg / sq.m over entire area with overlaps and sealed all as specified and directed. (d) Again applying a tack coat ofhot blown bitumen 85/25 @ 1.2 kg / sq.m over water proofing membrance. (e) Dusting dry sand @ 0.75 kg per sq.m over water proofing membrane. (f)Fixing of GI pipe medium grade 20mm bore as spout pipe of 50mm of length, complete. |
| 37 | PCC 1:5:10, type E-2 (using 40 mm graded stone aggregate) for filling up sunken floor over felt / sub base of floor, complete all as specified and directed. |
| 38 | Taking up or down galvanised steel tubing 15mm bore including connections, complete all as specified and directed. |
| 39 | Taking up or down galvanised steel tubing 20mm bore including connections, complete all as specified and directed. |
| 40 | GI tubing medium grade, galvanised with all fittings including short lengths, laid in floors or fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 15mm bore of pipe, complete all as specified and directed. |
| 41 | GI tubing medium grade, galvanised with all fittings including short lengths, laid in floors or fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 20mm bore of pipe, complete all as specified and directed. |
| 42 | Re-fixing of retrieved old 15 mm dia bore steel water tubing and connection in new or old position as directed, fixed to wall, ceiling or laid in floors including necessary cutting and making of new threads for fixing of new fittings such as and including provision of elbows, tees, sockets, union, , reducer, etc as required, complete all as specified and directed. |
| 43 | Re-fixing of retrieved old 20 mm dia bore steel water tubing and connection in new or old position as directed, fixed to wall, ceiling or laid in floors including necessary cutting and making of new threads for fixing of new fittings such as and including provision of elbows, tees, sockets, union, , reducer, etc as required, complete all as specified and directed. |
| 44 | Rotational moulded HDPEwater storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms), fixed in repair, complete all as specified and directed. |
| 45 | Rotational moulded HDPEwater storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms), fixed in repair, complete all as specified and directed. |
| 46 | Gun-metal, globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for ironpipe and fixed, fixed in repairs, complete all as specified and directed. |
| 47 | Ball valves, high pressure PTMT with epoxy coated aluminium rod and high density plastic ball secured for iron pipe of dia 20mm (minimum weight 210 grams), fixed in repairs, complete all as specified and directed. |
| 48 | UPVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls or laid in floors or trenches, fixed in repair, complete all as specified and directed.. |
| 49 | UPVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls or laid in floors or trenches, fixed in repair, complete all as specified and directed.. |
| 50 | UPVC (SWR) bends any radius, 75 mm bore complete all as specified and directed. |
| 51 | UPVC (SWR) bends any radius, 110 mm bore complete all as specified and directed. |
| 52 | UPVC (SWR) junction single, (Single T) equal or unequal, 75 mm bore, with oval and accessed door jointed with adhesive, fixed in repair, complete all as specified and directed.. |
| 53 | UPVC (SWR) junction single, (Single T) equal or unequal, 110 mm bore, with oval and accessed door jointed with adhesive, fixed in repair, complete all as specified and directed.. |
| 54 | Stack clamps out of 50 mm by 5 mm flat iron and iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm bore of pipe, complete all as specified and directed. |
| 55 | Stack clamps out of 50 mm by 5 mm flat iron and iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe, complete all as specified and directed. |
| 56 | UPVC (SWR) floor trap, 75 mmbore,plain with grating including jointing with solvent cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), fixed in repair, complete all as specified and as directed. |
| 57 | Stainless steel plate rack (utensil rack) of size (600 mm x 750 mm) and depth 250 mm made with 0.63 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut / bolts including taking down old and unserviceable plate rack of any size and any type, complete all as spcified and directed. |
| 58 | Looking mirror, 600mm x 450mmsize, of selected quality ofoval shapeglass, mounted on 6mm thick AC building board or commercial ply woodwith PVC frameincluding all necessary fixing arrangement & fixed to wooden plug with chromium plated brass screws and cup washers, fixed in repair, complete all as specified and directed. |
| 59 | Kitchen Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboaratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including supply and fixing cantilever brackets of mild steel angle 35 mm x 35 mm x 5 mm, 32mm dia brass waste coupling, 32 mm dia PVC waste pipe (rigid quality) and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410 mm x 330 mm x 160 mm, fixed in repair,. complete all as specified and directed. |
| 60 | Angle valves, 15 mm bore, castscrewed down, high pressure, with crutch or butter fly handle,for iron pipe or for unions,fixed in repair,complete all as specified and directed. MAKE :- L&K Cat No 0047 or techno-commercially equivalent model as approved by GE in makes specified here-in-after. |
| 61 | Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions, 15 mm bore, fixed in repair, complete all as specified and directed. |
| 62 | Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15 mm bore, fixed in repair, complete all as specified and directed. |
| 63 | Grating round 100 mm dia of PTMT (minimum weight 100 gms), fixed in repairs, completeall as specified and directed. |
| 64 | Square grating 150 mm size of PTMT (minimum weight 100 gms), fixed in repair, complete all as specified and directed. |
| 65 | Supply only pillar tap cast copper alloywith capstan heads chromium platedfancy type screweddown high pressure with or without lettered hot or coldwith long screwed shank and fly nuts, screwed for iron pipe 15 mm bore, complete all as specified and directed. |
| 66 | Brass chromium plated shower rose 65 to 90 mm size with swivel joints, fixed in repair, complete all as specified and directed. |
| 67 | PVC low level flushing cistern, 10 litre capacity, white’ with inlet, float valve including bracket with 32mm dia PVC pipe 600 mm longfixed in repair, complete all as specified and directed. |
| 68 | PVC connection 600mm long and 15 mm dia with brass fly nut at both ends,fixed in repair, complete all as specified and directed. |
| 69 | PVC waste pipe 32mm dia, fixed in repair, complete all as specified and directed. |
| 70 | PVC waste pipe 40mm dia, fixed in repair, complete all as specified and directed. |
| 71 | Vitreous china squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe, CI trap 100 mm bore of pipe etc, fixed in repair, complete all as specified and directed. |
| 72 | Vitreous China wash hand basin white flat back of size 550 mm x 400 mm fixed oncantilever brackets of mild steel including 32mm dia brass waste coupling, fixed in repair, completed all as specified and directed. |
| 73 | Vitreous china wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat coverincluding connection to drain (or outgoing pipe, and to flushing pipe and antisyphonage pipe etc with aluminium hinging device,fixed in repair, completed all as specified and directed. NOTE:- Plastic seat cover shall be measured separately as "Supply only" under respective item of this Schedule. |
| 74 | Supply only water closet seat cover, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, complete all as specified and directed. |
| 75 | Taking down chowkhat or frames with shutters (without taking off shutters from the frames) areanot exceeding 1.5sq.m each and removing from site, complete all as specified and directed. |
| 76 | Taking down chowkhat or frames with shutters (without taking off shutters from the frames) area exceeding 1.5sq.m but not exceeding 4 sq.m each and removing from site. complete all as specified and directed. |
| 77 | Taking down shutter of any description, exceeding 1.00 sq.m but not exceeding 2.00 sq.m each, complete all as specified and directed. |
| 78 | Taking down shutter of any description, not exceeding 1.00 sq.m each,complete all as specified and directed. |
| 79 | PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in hold fasts including necessary use and waste of form work, complete all as specified and directed. |
| 80 | Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed. |
| 81 | Rolled mild steel conforming to Fe 410-W (Gde-E- 250) quality-A, sections as in framing for cladding, glazing and the like including door frames/ chowkhats or cooler stands, fixed with angle cleats and connecting plates, etc including necessary cutting bending welding if required, complete all as specified and directed. |
| 82 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore |
| 83 | Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore |
| 84 | Factory made solid panel PVC wire gauge door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MSframe shall be covered with heat molded plain colourPVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, panel will be of wire gauge on lieu of PVC sheet panel. The wire gauge shall be wrapped on an additional square 8mm M S solid tube and this tube shall be welded to M S tubes. The wire gauge shall be stretched to tighten firmly, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore |
| 85 | Flush shutters 30 mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides, complete all as specified and directed. |
| 86 | Mild steel sliding door bolts, 250 mm long, enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed. |
| 87 | Aluminium anodised barrel tower bolts of extruded section and fixed, 150 mm long, complete all as specified and directed. |
| 88 | Butt hinges medium weight cold rolled mild steel, 100 mm long, complete all as specified and directed. |
| 89 | Butt hinges, 100 mm long, extrucded aluminium alloy withbrass/bronze hinge pin, anodised type B-21, complete all as specified and directed. |
| 90 | Aluminium anodised alloy handles, 150mm long extruded, cast type fixed with screws , complete all as specifeid and directed. |
| 91 | Aluminium anodised hasp and staple, 150 mm long, fixed in repair, complete all as specified and directed. |
| 92 | Mild steel, ordinary rat tail rod pattern spring including roller and roller plate, 300 mm long, fixed in repair, complete all as specified and directed. |
| 93 | Block board, 18 to 19 mm thick,grade-2 quality, interior grade, decorative type with decorative face veneer one side and fixed as in cup board shutter and fixed with screw and teak wood beading 3mm thick all around / exposed surfaces, fixed in repair, complete all as specified and directed. |
| 94 | Factory made steel window with side hung shutter including box type hinges with steel handle, steel peg stay, complete with glazing bar, dovetailed or welded, fixed in repair, complete all as specified and directed. |
| 95 | Factory made steel window with side hung shutter including box type hinges with steel handle, steel peg stay, complete without glazing bar, dovetailed or welded, fixed in repair, complete all as specified and directed. |
| 96 | Factory made steel ventilator with top hung shutter including hinges, steel peg stay,fixed in repair, complete all as specified and directed. |
| 97 | Aluminium (Diecast) body door closer, hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed,fixed in repair, complete all as specified and directed. |
| 98 | Taking down aluminium door shutter from frame, area of shutter exceeding 1.0 sq.m butnot exceeding 2.0 sq.mand re-fixing in same opening after repair of parts such as clip, easing, rubber beads, greasing / oiling and including replacement of components i.e. middle rail, top rail and handle complete, includikng replacement of locking arrangement, replacement of floor door spring for smooth functioning, complete all as specified and directed NOTE: The unit quoted rate shall deemed to be inclusive of all spare parts as required for smooth functioning of door,The tenderers are requested to visit the site and ascertain quantum of repairs involved on any working day with prior permission from the GE.No extra claim what-so-ever shall be entertained at later stage on this account and GE decision shall be final and binding. |
| 99 | Powder coated Aluminium door (thickness of powder coating shall not be less than 50micron) single leaf with aluminium frame of section 47.62mm x 44.45mm x 1.88 mm thick, shutter with bottom & middle rail of section 100mm x 44.5mm x 2 mm thick and styles & top rail of section 85mm x 44.5mm x 1.56 mm thick with centrally locking arrangement with lock of make ‘GODREJ’ or ‘LINK’ 7 lever and floor door spring hydraulically regulated including jointingcleats, fixing of 2 Nos of 150mm long aluminium handles and 2 Nos of 150mm tower bolts, necessary numbers of floor spring and glazing with 5.5 mm thick ordinary plain glass includingnecessary fittings, fixtures and aluminium snap beads, fixed in repair, completeall as specified and directed. NOTE:- The aluminium door area inlcuding door frame shall only be measured for payment purpose.However, the quoted rate per unit shall deemed to be inclusive of cost of above mentioned fittings and fixtures required per one single leaf door. |
| 100 | Powder coated Aluminum window (thickness of powder coating shall not be less than 50micron) with aluminum frame of section 47.62mm x 44.45mm x 1.88 mm mm thick with shutters having styles & rails of aluminum section 47.62mm x 44.45mm x 1.62 mm thick including jointing cleats, glazing clips, rubber packing, aluminum snap beading, screws anodized aluminum fittings such as hinges, 2 Nos tower bolts, 2 Nos handles etc including 5.5 mm thick ordinary plain glass complete. Including providing and fixing aluminum chequered grill of anodized section of mesh 100mm x 100mm made with 08 mm dia aluminium bar fixed to frame with 20mm x 205 mm aluminum flat with screws, fixed in repair, complete all as specified and directed. NOTE:- The aluminium window area inlcuding window frame shall only be measured for payment purpose.However, the quoted rate per unit shall deemed to be inclusive of cost of above mentioned fittings and fixtures required per one window shutter. |
| 101 | Aluminium partition frame work anodized frame of size 62.5mm x 37mm x 1.5 mm thick with bottom & middlerails of aluminium section 62.5mm x 37mm x 1.5 mm thick and styles, top of section 62.5mm x 37mm x 5.5 mm thick including jointing cleats, filled with 12mm thick pre-laminated partical board intrerior grade up to middle rail from bottom and 5 to 6 mm thick plain / frosted glass in balance portion secured with aluminum fillet of size 20mm, including provisin of necessary fittings and fixtures, fixed in repair, complete all as specified and directed. |
| 102 | Aluminium grill Decogrill DG-117 with aluminium powder coated meshwith Square tube (solid) 6 mm thick sheet fixed in repair, complete all as specified and directed. |
| 103 | Providing and fixing E-boardMake: Everest, Design "Lake and Hill" of size 605mm x 605mm x 4mm thick white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section (White powder coated). The framework shall comprise of main runner made from 0.33mm thick GS sheet and of size 24mm x 32mm x 300mm and secured at 1200mm maximum centre securely fixed to structural soffits with hangers of 2mm dia GI wire to be fixed with approved rawl plugs, adjusters and screws. Flush fitting of 1200mmm long cross Tee (with double stiching) to be interlocked between main runners at 600mm centre to form 1200 x 1600 mm modules cross tee longer than 600mm to be supported independently. 600 x 600mm doubles to be formed by fittings 600mm long cross tee centrally between the 1200mm cross tee. Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19 x 19 mm and 300mm long of white colour all as per manufacturers instructions, fixed in reapir, complete all as specified and directed. Make of Frame work : Armstong / Sanit Gobain or techno-commercially equivalent make as approved by GE. |
| 104 | Providing and fixing E-boardMake: Everest, Design "Lake and Hill" of size 605mm x 605mm x 4mm thick white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on old / existing frame work all as per manufacturers instructions, fixed in repair, complete all as specified and directed. Make of Frame work : Armstong / Sanit Gobain or techno-commercially equivalent make as approved by GE. |
| 105 | Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges as in roof covering, complete all as specified and directed. |
| 106 | Asbestos cement corrugated sheet, 6 mm thick, fixed with ‘L’ type or ‘J’ type or cranked hook bolts, complete all as specified and directed. |
| 107 | Asbestos cement corrugated sheet, 6 mm thick, fixed with ‘L’ type or ‘J’ type or cranked hook bolts, except sheets, complete all as specified and directed. NOTE:- Serviceable AC sheets retrieved from dismantling shall be re-used in this item. |
| 108 | Asbestos cement two piece adjustable plain wing ridge, 6 mm thick, fixed with ‘L’ type or ‘J’ type or cranked hook bolts,complete all as specified and directed. |
| 109 | Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensilestrength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as, complete all as specified and directed. |
| 110 | Framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, and similar work conforming to Fe-290 Gde-E-165, fixed in repair, complete all as specified and directed. |
| 111 | Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specifed and direcetd. |
| 112 | Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, fixed in repair, complete all as specifed and direcetd. |
| 113 | Hacking out old broken glass (any thickness, size, quality or description) from wooden or metalframes fixed with putty or beads etc, complete as specified & directed. |
| 114 | Sheet glass, 3 mm thick, ordinary quality and glazing with oil putty or wooden beads in square not exceeding 0.5 sq. m in each pane,complete all as specified and directed. |
| 115 | Sheet glass frosted on one side, 4 mm thick, ordinary quality and glazing with oil putty or wooden beads in square not exceeding 0.5 sq. m in each pane,complete all as specified and directed. |
| 116 | Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed. |
| 117 | Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, square/rectangular hollow section)including distance pieces, cleats etc. and other connections conforming to Fe 410 -W (GdeE-250) quality "A" including welding, cutting, etc., complete all as specified and directed. |
| 118 | Mild steel tubing of 25 mm dia with PVC coating for curtain rod fancy type including fancy type PVCbrackets & Hooks (wall to wall or flush to wall) for securing to curtain rod, fixed in repair, complete all as specifed and direcetd. |
| 119 | Disconnecting existing tanks, setting aside (or lowering if required ) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position capacity exceeding 250 but not exceeding 500 litre, complete all as specified and directed. |
| 120 | Disconnecting existing tanks, setting aside (or lowering if required ) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position capacity exceeding 500 but not exceeding 1000 litre, complete all as specified and directed. |
| 121 | Preparation of new wooden surfaces exceeding 10 cm width or girth, using sand or emery paper and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. |
| 122 | Preparation of new steel and iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed. |
| 123 | Applying two coats of acrylic emulsion paint over one coat of chalk whiting onnew plastered surfaces, including preparation of surface, complete all as specified and directed. |
| 124 | Preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed. |
| 125 | ACP sheets as in cladding / panelling 3 mm thick on mild steel frame work, 0.75metre x 0.45metre fixed in wall or RCC coloumn with screw by drilling holes and jointed / sealed with silicon all as per manufacturer instruction, fixed in repair, complete all as specified and directed. |
| 126 | Bip tap of standard PTMT any colour screwed for iron pipe of bore 15 mm and fixed (Minimum weight 90gms), fixed in repair, complete all as specified and directed. |
| 127 | Mild Steel handle (left or right) for steel window of existing size including necessary welding / riveting etc, fixed in repair, complete all as specified and directed. |
| 128 | Repairs to Butt hinges / single action spring hinges / double action spring hinges / projecting type hinges / box type hinges by welding the same to existing door frame / mild steel window frame, fixed in repair, complete all as specified and directed. |
| 129 | PVC Covers for PVC water tanks of capacity exceeding 500 litres but not exceeding/1000 Litres, fixed in repair,complete all as specified and directed. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
