|
| 1 | Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep in any type of soil getting out and levelling of bottom surface to required level for poles / stay assembly / cable complete all as specified and as directed. |
| 2 | Material and labour for road cutting, PCC hard standing as per site requirement including excavation for laying of GI pipe and making good the disturbed surfaces all as per existing surface complete all as specified and as directed. |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25m thick complete all as specified and as directed. |
| 4 | Removing excavated material from site to a distance not exceeding 50mtr away and depositing where directed not exceeding 1.5 mtr from the starting point complete all as specified and as directed. |
| 5 | Material and labour for brick work with sub class \"B\" bricks straight or curved on plan not exceeding 6m mean radius built in CM 1:4 for sluice valve pit complete all as specified and as directed. |
| 6 | Material and labour for rendering 10mm thick on fair faces of brick work or concrete surfaces inside sluice valve pit in CM 1:6 complete all as specified and as directed. |
| 7 | Surface excavation not exceeding 30 cm deep and averaging 50 cm deep and getting out in soft / loose soil including taking out vegetation from entire area of water supply installation complete all as specified and as directed. |
| 8 | Material and labour for cement concrete in foundation subways (1:4:8) type D-2 aggregate including demolishing existing complete all as specified and as directed. |
| 9 | Material and labour for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) for subways 40mm thick including demolishing existing complete all as specified and as directed. |
| 10 | Taking down plaster of any thickness on brick or stone wall of sluice valve pit including racking out joints, hacking for key, scrubbing down, of any description complete all as specified and as directed. |
| 11 | Material and labour for preparation of rusted or previous untreated surface of old painted surfaces of sluice valves pit MS sheet cover scrubbing, cleaning and painting to sluice valve pit both side of any description over 10cm in width or girth not otherwise described and painted with synthetic enamelled black paint two coat over a coat of red oxide primer including writing location / area with white paint complete all as specified and as directed. |
| 12 | Taking out unserviceable / damage sluice valve pit MS top cover along with angle iron frame for repair, denting, necessary welding work, provision of replacement of two no\"s of MS hinges 6\" heavy duty and provision of lifting handle and refixing in position along with angle iron frame with the help of nut, bolt after necessary repair / in position as per site requirement complete all as specified and as directed. |
| 13 | Taking out unserviceable sluice valve of size 100 / 150 mm bore dia in position for repair complete with refacing, regrinding, replacing staffing box of spindle, nut, bolt, washer, rubber gaskits, repair to GM seat with gaskit, gland cup filling gland dori and refixing after repair in site complete all as specified and as directed. |
| 14 | Material and labour for replacement of CI sluice valve PN 1.6 with iron wheel head of size 150mm bore with stainless steel spindle both end flanged complete with nut, bolts, washer and rubber gaskit 3mm thick conforming to ISI-14846/2000 complete all as specified and as directed. |
| 15 | Material and labour for replacement of CI sluice valve PN 1.6 with iron wheel head of size 100mm bore with stainless steel spindle both end flanged complete with nut, bolts, washer and rubber gaskit 3mm thick conforming to ISI-14846/2000 complete all as specified and as directed. |
| 16 | Material and labour for replacement of CI sluice valve PN 1.6 with iron wheel head of size 80mm bore with stainless steel spindle both end flanged complete with nut, bolts, washer and rubber gaskit 3mm thick conforming to ISI-14846/2000 complete all as specified and as directed. |
| 17 | Material and labour for replacement of CI non return valve PN 1.6 of size 150mm bore with stainless steel working part conforming to ISI-5312/2004 duly IS marked complete with rubber gaskit 3mm thick and nut, bolts and washer couple complete all as specified and as directed. |
| 18 | Material and labour for replacement of tubing GI \"medium grade\" with all fittings laid in floor or trenches including taking out old unserviceable pipe of size 100 mm dia complete all as specified and as directed. |
| 19 | Material and labour for replacement of tubing GI \"medium grade\" with all fittings laid in floor or trenches including taking out old unserviceable pipe of size 80 mm dia complete all as specified and as directed. |
| 20 | Material and labour for replacement of tubing GI \"medium grade\" with all fittings laid in floor or trenches including taking out old unserviceable pipe of size 50 mm dia complete all as specified and as directed. |
| 21 | Material and labour for replacement of tubing GI \"medium grade\" with all fittings laid in floor or trenches including taking out old unserviceable pipe of size 40 mm dia complete all as specified and as directed. |
| 22 | Material and labour for replacement of tubing GI \"medium grade\" with all fittings laid in floor or trenches including taking out old unserviceable pipe of size 25 mm dia complete all as specified and as directed. |
| 23 | Material and labour for replacement of tubing GI \"medium grade\" with all fittings laid in floor or trenches including taking out old unserviceable pipe of size 20 mm dia complete all as specified and as directed. |
| 24 | Material and labour for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 50 mm bore complete all as specified and as directed. |
| 25 | Material and labour for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 40 mm bore complete all as specified and as directed. |
| 26 | Material and labour for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 25 mm bore complete all as specified and as directed. |
| 27 | Material and labour for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 20 mm bore complete all as specified and as directed. |
| 28 | Material and labour for replacement of cast iron pipe with spigot and socket ends centrifugally cast class \"B\" of any length conforming to ISI laid in trenches of size 150 mm bore complete all as specified and as directed. |
| 29 | Material and labour for replacement of cast iron pipe with spigot and socket ends centrifugally cast class \"B\" of any length conforming to ISI laid in trenches of size 100 mm bore complete all as specified and as directed. |
| 30 | Material and labour for replacement of CI fitting any type, radius and angle for spigot and socketed and flanged pipes, laid piece both end flanged or one end flanged other socketed, cap, plug, dead end flanged, split collar, reducer of any size upto 150 mm bore pipe complete all as specified and as directed. |
| 31 | Material and labour for replacement of CI split coller of size 150mm dia complete with rubber gaskit 3 mm thick and nut, bolts, washer etc complete all as specified and as directed. |
| 32 | Material and labour for replacement of sluice valve spindle stainless steel suitable for 150 mm sluice valve complete with check nut complete all as specified and as directed. |
| 33 | Labour for repair / rectification of leakage of underground water pipe line GI of size 25 to 100 mm dia with excavation Appx 1.0 X 1.0 X 1.0 mtr around the leakage, returning filling in, removal, cutting / disconnecting to existing leakage GI Pipe line in position for repair / rectification of leakage, replacement of unserviceable fittings and welding work as per site requirement and restore the water supply complete all as specified and as directed.Note: (Spare / fitting shall be measured and paid separately). |
| 34 | Supply only GI union 100 mm dia complete all as specified and as directed. |
| 35 | Supply only GI union 40 mm dia complete all as specified and as directed. |
| 36 | Supply only GI union 25mm dia complete all as specified and as directed. |
| 37 | Supply only GI union 20 mm dia complete all as specified and as directed. |
| 38 | Supply only GI Socket 100 mm dia complete all as specified and as directed. |
| 39 | Supply only GI Socket 40 mm dia complete all as specified and as directed. |
| 40 | Supply only GI Socket 25 mm dia complete all as specified and as directed. |
| 41 | Supply only GI Socket 20 mm dia complete all as specified and as directed. |
| 42 | Supply only GI Elbow 40 mm dia complete all as specified and as directed. |
| 43 | Supply only GI Elbow 25 mm dia complete all as specified and as directed. |
| 44 | Supply only GI Elbow 20 mm dia complete all as specified and as directed. |
| 45 | Supply only GI Tee 40 mm dia all as specified and as directed. |
| 46 | Supply only GI Tee 25 mm dia complete all as specified and as directed. |
| 47 | Supply only GI Tee 20 mm dia complete all as specified and as directed. |
| 48 | Supply only GI Nipple 40mm dia 6 inch long complete all as specified and as directed. |
| 49 | Supply only GI Nipple 25 mm dia 4 inch long complete all as specified and as directed. |
| 50 | Supply only GI Nipple 20 mm dia 4 inch long complete all as specified and as directed. |
| 51 | Supply only GI reducer 25/20 mm dia complete all as specified and as directed. |
| 52 | Supply only GI reducer 20/15 mm dia complete all as specified and as directed. |
| 53 | Labour for repair / rectification of leakage of underground CI / DI pipe line of size 80 to 150 mm bore dia in position complete with excavation Appx 1.0 X 1.0 X 1.0 mtr around the leakage, returning filling in, removal, cutting / dismantling of leakage complete with and including cocking to existing lead joint, filling new lead joint burning and taking out existing lead joint as per site requirement and restore the water supply complete all as specified and as directed.Note: (Spare / fitting shall be measured and paid separately). |
| 54 | Material and labour for replacement for filling CI spigot and socketed joint of any size Lead pig complete all as specified and as directed. |
| 55 | Material and labour for replacement for filling CI spigot and socketed joint of any size Lead wool complete all as specified and as directed. |
| 56 | Material and labour for replacement for filling CI spigot and socketed joint of any size Spun Yarn complete all as specified and as directed. |
| 57 | Supply and fixing in replacement Altoch GP packing of 45 Kg complete all as specified and as directed. |
| 58 | Supply and fixing in replacement of unserviceable bolt 16 mm dia X 6\"\" long fully threaded with counted head nuts and washer heavy duty conforming to ISI for MS column pipe / CI flanged pipe complete all as specified and directed. |
| 59 | Repair / Maint / service to swimming pool filteration plant complete with cleaning of underground sump by removing dirt and mud, replacement of unserviceable spare parts fitting valves, filter media, PVC strainer, Pressure gauge, Butterfly valve, air vent pipe complete with cleaning internally including taking out all filter media outside and kept separately each media at site for reuse, preparing external services of filter media and make the surface smooth and applying two coats of synthetic enamel paint and a coat of red oxide primer compete with suction and discharge pipe and relaying all filter media in proper layer duly washed and tested on full load complete all as specified and as directed.Note: Spare shall be measured and paid separately. |
| 60 | Supply only water pressure gauge 10 KG 100 mm dia complete with 3/8 inch brass sampling cock complete all as specified and as directed. |
| 61 | Supply only butterfly valve cast iron body with gun metal sheet conforming to IS-13095 of size 150 mm dia complete all as specified and as directed. |
| 62 | Material and labour for replacement of gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 20 mm bore complete all as specified and as directed. |
| 63 | Supply only double deck type PP strainer of size 3/8 inch or 1/2 inch complete all as specified and as directed. |
| 64 | Supply and fixing in replacement suction sweeper complete assembly for swimming pool (pool cleaner) 36 inch long complete with wheels, PVC core nylon brush 36 inch NRV complete all as specified and all as directed. |
| 65 | Supply and fixing in replacement suction flexible rubber hose pipe 80 mm dia braded type green colour conforming to ISI complete with suitable size MS clamp complete all as specified and as directed. |
| 66 | Repair / Maint / service to swimming pool dewatering centrifugal pump set single stage 7.5 HP complete with replacement of CI impeller, neck ring, bearing, hosing, sleeve and remetalling to pump shaft, welding, brazing and polishing etc and make the pump serviceable complete all as specified and as directed.Note: Spare shall be measured and paid separately. |
| 67 | Supply only CI Impeller complete all as specified and as directed. |
| 68 | Supply only ball bearing complete all as specified and as directed. |
| 69 | Supply only stainless steel sleeve complete all as specified and as directed. |
| 70 | Supply only stainless steel neck ring complete all as specified and as directed. |
| 71 | Supply only pump shaft coupling with key tyre type complete all as specified and as directed. |
| 72 | Supply only superior quality copper sulphate complete all as specified and as directed. |
| 73 | Supply and fix in replacement PVC insulation patch roll for submersible cable connection complete all as specified and as directed. |
| 74 | Disconnecting all incoming / outgoing electric connection from LT panel / starter / electric motor carefully including dismantling / opening nut, bolt of discharge head and taking out submersible / VT motor pumping set complete with MS column pipe having capacity 3 to 5 HP and shifting in workshop for repair / servicing of pumping set and re-assembling / electric connection and testing at site on full load complete all as specified and directed by Engr-in-Charge. |
| 75 | Disconnecting all incoming / outgoing electric connection from LT panel / starter / electric motor carefully including dismantling / opening nut, bolt of discharge head and taking out submersible / VT motor pumping set complete with MS column pipe having capacity 7.5 to 25 HP and shifting in workshop for repair / servicing of pumping set and re-assembling / electric connection and testing at site on full load complete all as specified and directed by Engr-in-Charge. |
| 76 | Material and labour for strip opening complete submersible pumping set having capacity 3 to 15 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling / installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items as under: - |
| 77 | Supply only cast iron stage bowl complete all as specified and as directed. |
| 78 | Supply only cast iron suction discharge chamber complete all as specified and as directed. |
| 79 | Supply only stainless steel neck ring complete all as specified and as directed. |
| 80 | Supply only stainless steel bowl bush complete all as specified and as directed. |
| 81 | Supply only stainless steel coupling sleeves complete all as specified and as directed. |
| 82 | Supply only cast iron impeller with key complete all as specified and as directed. |
| 83 | Supply only body studs fully threaded complete all as specified and as directed. |
| 84 | Supply only stainless steel pump shaft complete all as specified and as directed. |
| 85 | Supply only stainless steel pump shaft coupling with key complete all as specified and as directed. |
| 86 | Supply only cast iron NRV with NRV seat and cone complete all as specified and as directed. |
| 87 | Supply only stainless steel sleeves for bowl complete all as specified and as directed. |
| 88 | Supply only rubber bush complete all as specified and as directed. |
| 89 | Supply only strainer for pump complete all as specified and as directed. |
| 90 | Material and labour for strip opening complete submersible pumping set having capacity 20 to 25 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling / installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective items as under: - |
| 91 | Supply only cast iron stage bowl complete all as specified and as directed. |
| 92 | Supply only cast iron suction discharge chamber complete all as specified and as directed. |
| 93 | Supply only stainless steel neck ring complete all as specified and as directed. |
| 94 | Supply only stainless steel bowl bush complete all as specified and as directed. |
| 95 | Supply only stainless steel coupling sleeves complete all as specified and as directed. |
| 96 | Supply only cast iron impeller with key complete all as specified and as directed. |
| 97 | Supply only body studs fully threaded complete all as specified and as directed. |
| 98 | Supply only stainless steel pump shaft complete all as specified and as directed. |
| 99 | Supply only stainless steel pump shaft coupling with key complete all as specified and as directed. |
| 100 | Supply only cast iron NRV with NRV seat and cone complete all as specified and as directed. |
| 101 | Supply only stainless steel sleeves for bowl complete all as specified and as directed. |
| 102 | Supply only rubber bush complete all as specified and as directed. |
| 103 | Supply only strainer for pump complete all as specified and as directed. |
| 104 | Material and labour for strip opening to submersible motor / VT motor having capacity 3 to 15 HP and re-winding with super enamelled copper winding wire heavy duty heat resistance confirming to IS of same gauge and no\"s of turns complete with realignment of motor slots and insulating materials i.e. varnishing, bamboo strips, leather papers, cotton tapes includingreplacement of unserviceable / defective spare parts and drying complete and re-assembling after repair / rewinding and testing at site on full head complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective item as under: - |
| 105 | Supply only thrust plate with circlip and key complete all as specified and as directed. |
| 106 | Supply only thrust plate bearing housing complete all as specified and as directed. |
| 107 | Supply only bearing for motor complete all as specified and as directed. |
| 108 | Supply only rubber oil seal complete all as specified and as directed. |
| 109 | Supply only cast iron sand guard complete all as specified and as directed. |
| 110 | Supply only rubber diaphragam with plate complete all as specified and as directed. |
| 111 | Supply only stainless steel sealing bush complete all as specified and as directed. |
| 112 | Material and labour for strip opening to submersible motor / VT motor having capacity 20 to 25 HP and re-winding with super enamelled copper winding wire heavy duty heat resistance confirming to IS of same gauge and no\"s of turns complete with realignment of motor slots and insulating materials i.e. varnishing, bamboo strips, leather papers, cotton tapes includingreplacement of unserviceable / defective spare parts and drying complete and re-assembling after repair / rewinding and testing at site on full head complete all as specified and as directed. Note: - Spare parts shall be measured and paid separately under respective item as under: - |
| 113 | Supply only thrust plate with circlip and key complete all as specified and as directed. |
| 114 | Supply only thrust plate bearing housing complete all as specified and as directed. |
| 115 | Supply only bearing for motor complete all as specified and as directed. |
| 116 | Supply only rubber oil seal complete all as specified and as directed. |
| 117 | Supply only cast iron sand guard complete all as specified and as directed. |
| 118 | Supply only rubber diaphragam with plate complete all as specified and as directed. |
| 119 | Supply only stainless steel sealing bush complete all as specified and as directed. |
| 120 | Labour for welding, metalling, grinding, polishing and lathe / machine work for re-alignment to rotor assembly and making the suitable size for fitment of rotor bearing complete with replacement of unserviceable / defective spare parts of capacity 3 to 15 HP complete all as specified and as directed.Note: - Spare parts shall be measured and paid separately under respective items as under: - |
| 121 | Supply only rotor sleeves stainless steel complete all as specified and as directed. |
| 122 | Supply only rotar GM bearing bush complete all as specified and as directed. |
| 123 | Supply only rotor upper and lower bearing housing complete all as specified and as directed. |
| 124 | Supply only rotor upper and lower tee bolts complete all as specified and as directed. |
| 125 | Supply only studs for adopter housing complete with plain washer and hexagonal nut complete all as specified and as directed. |
| 126 | Supply only GM drain plug complete all as specified and as directed. |
| 127 | Labour for welding, metalling, grinding, polishing and lathe / machine work for re-alignment to rotor assembly and making the suitable size for fitment of rotor bearing complete with replacement of unserviceable / defective spare parts of capacity 20 to 25 HP complete all as specified and as directed.Note: - Spare parts shall be measured and paid separately under respective items as under: - |
| 128 | Supply only rotor sleeves stainless steel complete all as specified and as directed. |
| 129 | Supply only rotor GM bearing bush complete all as specified and as directed. |
| 130 | Supply only rotor upper and lower bearing housing complete all as specified and as directed. |
| 131 | Supply only rotor upper and lower tee bolts complete all as specified and as directed. |
| 132 | Supply only studs for adopter housing complete with plain washer and hexagonal nut complete all as specified and as directed. |
| 133 | Supply only GM drain plug complete all as specified and as directed. |
| 134 | Supply and fixing in replacement of submersible cable 16 Sqmm 3 core flat copper conductor heavy duty 1100 Volts grade confirming to ISI complete all as specified and directed by Engr-in-Charge.Note: - Old cables shall be deposited in store yard. |
| 135 | Supply and fixing in replacement of oil immersed star delta starter heavy duty manual operated suitable for submersible / VT pumping set with overload relay range 37-50 Ampere, 415 volts, 50 Hz, 3 phase confirming to IS complete with initial filling of oil all as specified and as directed. |
| 136 | Supply and fixing in replacement of DOL starter suitable for submersible / centrifugal / monoblock set heavy duty with overload relay range 13-18 Ampere, 415 volts, 50 Hz, 3 phase complete with provision of volt / Amp meter, indicators, selector switches, push ON / OFF switch complete all as specified and as directed. |
| 137 | Supply and fixing in replacement of DOL starter suitable for submersible / centrifugal / monoblock set heavy duty with overload relay range 18-25 Ampere, 415 volts, 50 Hz, 3 phase complete with provision of volt / Amp meter, indicators, selector switches, push ON / OFF switch complete all as specified and as directed. |
| 138 | Supply and fixing in replacement of fully automatic star delta starter 3 phase, 415 volt, 50 Hz, suitable for submersible pumping set heavy duty with overload relay range 37-50 Amp complete with provision of power contactor volt / Amp meter, push ON / OFF switch, selector switch, indicator and incomer MCB TP 63 Amp etc complete all as specified and as directed. |
| 139 | Taking out all incoming / outgoing electric connection from LT panel / starter / motor / voltage stabilizer carefully for repair to cable / rectification the fault and re-connecting in position after repair and preparation the cable and fixing complete with nut, bolts, washers for cable size 25 to 95 Sqmm complete all as specified and as directed. NOTE :- Preparation of 3.5 core cable, 4 wire each and will be considered as one job. |
| 140 | Supply and fixing in replacement of submersible motor rotor for 20 to 25 HP motor complete with bearing upper / lower bearing housing, sleeves, tee bolts and bush complete all as specified and directed by Engineer-in-Charge. |
| 141 | Supply and fixing in replacement of submersible motor stater for capacity 20 to 25 HP complete with thrust plate, thrust bearing with housing, studs, water seal, sand guard, rubber diaphragam with plate, sealing bush complete all as specified and directed by Engineer-in-Charge. |
| 142 | Material and labour for fabrication of MS clamp made out from flat 150 mm x 12 mm thick, bend to shape, drill a hole four no\"s in each clamp of size 16 mm dia suitable for holding MS column pipe size 150 mm dia complete with provision of four no\"s nuts, both 4\" long and washer complete as per sample all as specified and as directed. |
| 143 | Supply and fixing in replacement of cast iron discharge head assembly suitable for vertical turbine plumbing set having suction / discharge size 150 mm dia complete all as specified and directed by Engineer-in-Charge. |
| 144 | Material and labour for strip opening complete vertical turbine pumping set having capacity 7.5 to 20 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed.Note: - Spare parts shall be measured and paid separately under respective items as under: - |
| 145 | Supply only cast iron bowl complete all as specified and as directed. |
| 146 | Supply only cast iron suction / discharge bowl complete all as specified and as directed. |
| 147 | Supply only stainless steel neck ring complete all as specified and as directed. |
| 148 | Supply only cast iron impellers with key complete all as specified and as directed. |
| 149 | Supply only stainless steel shaft complete all as specified and as directed. |
| 150 | Supply only stainless steel coupling with key complete all as specified and as directed. |
| 151 | Supply only cast iron NRV with seat complete all as specified and as directed. |
| 152 | Supply only stainless steel bowl bush complete all as specified and as directed. |
| 153 | Supply only rubber bush complete all as specified and as directed. |
| 154 | Supply only body studs fully threaded complete all as specified and as directed. |
| 155 | Supply only stainless steel sleeves complete all as specified and as directed. |
| 156 | M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in mass filling for discharge head base complete with breaking / dismantling existing PCC block all as specified and directed by Engineer-in-Charge. |
| 157 | Supply and fixing in replacement of on load open execution change over switch front handle operated 4 pole, 415 volt, 50 Hz 125 Amp confirming to IS complete all as specified and directed by Engineer-in-Charge. |
| 158 | Supply and fixing in replacement of on load change over switch side handle operated 4 pole, 415 volt, 50 Hz 100 Amp confirming to IS all as specified and directed by Engineer-in-Charge. |
| 159 | Material and labour for fabrication of angle iron bracket 40 x 40 x 6 mm thick cutting, bend to shape drilling hole 16 mm 4 no\"s each bracket welding MS flat of 20 mm x 3 mm thick in each bracket and fixed on the wall with the help of nut, bolt suitable for run the cable of any size as per site requirement all as specified and directed by Engineer-in-Charge. |
| 160 | Supply and fixing in replacement chain pully moving chain made out from approx 10mm dia bar heavy duty with grade 80 alloy steel chain suitable for 5 Ton chain pully block having length 6 mtr conforming to IS-3832/1971 complete all as specified and as directed. |
| 161 | Supply and fixing in replacement of spur gear chain pully block heavy duty complete with grade 80 alloy steel chain suitable to take load upto 5 Ton capacity with provision of moving chain having length 6 mtr approx conforming to IS complete all as specified and as directed. |
| 162 | Supply and fixing in replacement of MCCB 4 pole, 125 amp, 16 KA, 415 volt, 50 Hz complete all as specified and directed. |
| 163 | Transporting air compressor and other allied equipment / material at site of tube well and installation of complete machinery all as specified and directed. |
| 164 | Redevelopment of tube well with air compressor of adequate capacity (not less than 250 Cfm) as per specification till the availability of sand free clear water, subject to minimum of 60 hrs of operation of air compressor (60 x 4500) complete all as specified and as directed. |
| 165 | Providing of pea shaped gravel as per specification and gravel shrouding in annular space between well and liner assembly required during redevelopment complete all as specified and as directed. |
| 166 | Stabilization and yield testing to tube well by using submersible pump of adequate capacity as per specifications (subject to minimum of 48 hours of development with submersible pump set) including conduction of sounding test (48 x 3200) complete all as specified and as directed.Note: - Submersible pumping set of adequate capacity will be brought by contractor at their own cost and rates for hiring submersible motor deemed to be included in item rate. |
| 167 | Dismantling and taking down electric motor of dozing system and shifting in workshop for repair and rewinding with super enamelled copper winding wire of same gauge and no\"s of turns complete with insulated material i.e. varnish, cotton tape, bamboo strips, emory paper and drying including replacement of unserviceable spare parts complete all as specified and as directed.Note: - Spare parts shall be measured and paid separately under respective items. |
| 168 | Supply only motor seal complete all as specified and as directed. |
| 169 | Supply only motor bearing complete all as specified and as directed. |
| 170 | Supply only motor fan blade complete all as specified and as directed. |
| 171 | Supply only rotor shaft complete all as specified and as directed. |
| 172 | Supply only coupling complete all as specified and as directed. |
| 173 | Dismantling and taking down dozing pumping set and shifting in workshop for repair / maintenance / overhauling and reassembly after necessary repair complete with and including replacement of unserviceable / defective spare parts and testing on load at site complete all as specified and directed.Note: - Spare parts shall be measured and paid separately under respective items. |
| 174 | Supply only Agitator assembly complete all as specified and as directed. |
| 175 | Supply only Agitator bearing complete all as specified and as directed. |
| 176 | Supply only Agitator shaft with SS blade duty FRP coated complete all as specified and as directed. |
| 177 | Supply only foot valve complete all as specified and as directed. |
| 178 | Supply only suction valve complete all as specified and as directed. |
| 179 | Supply only discharge valve complete all as specified and as directed. |
| 180 | Supply only injection fitting complete all as specified and as directed. |
| 181 | Supply only PE tubing 5/8\"\" (8 mtr) complete all as specified and as directed. |
| 182 | Supply only solenoid motor complete all as specified and as directed. |
| 183 | Supply only main head (PP / PVC) complete all as specified and as directed. |
| 184 | Supply only main head hexagonal bolts complete all as specified and as directed. |
| 185 | Supply only diphragam (taflon faced) complete all as specified and as directed. |
| 186 | Supply only Acrylic front cover complete all as specified and as directed. |
| 187 | Supply only speed / stroke nob complete all as specified and as directed. |
| 188 | Supply only toggle switch complete all as specified and as directed. |
| 189 | Supply only strainer for foot valve complete all as specified and as directed. |
| 190 | Supply only electronic controlled circuit plate complete all as specified and as directed. |
| 191 | Supply only NRV spring complete all as specified and as directed. |
| 192 | Supply only Air release valve complete all as specified and as directed. |
| 193 | Supply only power chord with plug complete all as specified and as directed. |
| 194 | Supply only injection check valve (NRV) complete all as specified and as directed. |
| 195 | Supply and fixing in replacement of heavy duty FRP service tank 150 litres complete with drain valve, level gauge, water inlet / outlet provision and CPV 15 mm pipe for feeding to main line complete all as specified and as directed. |
| 196 | Material and labour for fabricated MS angle iron frame heavy duty epoxy coated and anticorrosive paint bend to shape bending, welding and fixing on wall / floor to take the load of complete dozing system to avoid direct load of motor on tank complete as specified and as directed by Engineer-in-Charge. |
| 197 | Supply and fixing in replacement of chlorine test kit with coloured sample complete with all testing fillaments and OT solution in rexin finish wooden box complete all as specified and directed. |
| 198 | Supply and fixing in replacement of water pressure gauge 7 Kg / 10 Kg heavy duty 100 mm dia complete with brass sampling cock 3/8\" and pressure gauge cock complete all as specified and as directed. |
| 199 | Supply and fixing in replacement of OT solution chlorine test (500 ml) complete all as specified and as directed. |
| 200 | Supply and fixing in repair two single core 4 Sqmm for sub main wiring with copper conductor multistranded PVC insulated and unsheathed 1100 Volts grade in and including concealed PVC conduit with fixing accessories including one run of 2.5 Sqmm copper conductor as earth wire complete all as specified and as directed.Note: - Two runs of 4 Sqmm cable, one run of 2.5 Sqmm earth cable and one run of PVC conduit shall be measured as one running metre. |
| 201 | Providing cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) for repair to dosing system basement complete all as specified and as directed. |
| 202 | Supply and fixing in replacement of DOL starter single phase 220 Volt for dozing pump of existing make and capacity complete all as specified and as directed. |
| 203 | NOTE NO 1: -Samples of materials as approved will be kept in GE\"s sample room.NOTE NO 2: -All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE.NOTE NO 3: -Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings. |
