Construction C / O Cls At Bitra Construction Of Cable Landing Station In Bitra Under Kli Submarine Cable Project
Tender Value
4.40 Crore
Estimated cost
Bid Submission
29 Oct 2021
0 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
1770
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bitra → Lakshadweep
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction C / O Cls At Bitra Construction Of Cable Landing Station In Bitra Under Kli Submarine Cable Project
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal/spreading of excavated earth, lead up to 50m/within compound and lift up to 1.5m,as directed by Engineer-in-Charge. |
| 2 | All kinds of soil |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal/spreading of surplus excavated soil as directed, within a lead of 50 m/within compound |
| 4 | All kinds of soil. |
| 5 | Excavating trenches of required width for pipes, cables, etc. including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing/spreading of surplus excavated soil as directed, within a lead of 50 m/within compound : a)All kinds of soil |
| 6 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 8 | Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. |
| 9 | All kinds of soil. |
| 10 | Supplying and filling in plinth with quarry sand under floors, including watering, ramming, consolidating and dressing complete. |
| 11 | Supplying and filling in compound, non-cohesive soil brought from ouside including watering, ramming, consolidating and dressing complete. (The consolidated soil will be measured for payment). |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 13 | 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size ) |
| 14 | 1:5:10 (1 cement : 5 coarse sand(zone-III) : 10 graded stone aggregate 40 mm nominal size ) |
| 15 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing : |
| 16 | 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 17 | Extra for providing and mixing water proofing material in cement concrete per 50kg work in doses by weight of cement as per manufacturer’s specification. |
| 18 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth. |
| 19 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 20 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 21 | Reinforced cement concrete work in well-steining, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 22 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 23 | Foundations, footings, bases of columns, etc. for mass concrete |
| 24 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 25 | Suspended floors, roofs, landings, balconies and access platform |
| 26 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 27 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 28 | Stairs, (excluding landings) except spiral-staircases |
| 29 | Well steining |
| 30 | Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards |
| 31 | Weather shade, Chajjas, corbels etc., including edges |
| 32 | Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). |
| 33 | Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) |
| 34 | Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in small lintels/slab not exceeding 1.5m clear span up to floor five level, including the cost of required centering, shuttering but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone- III) : 3 graded stone aggregate 20 mm nominal size). |
| 35 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 36 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 37 | Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). |
| 38 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections |
| 39 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (The minimum and maximum cement content for the designmix concrete is 360kg/cum and 450kg/cum. Nothing extra shall be payable to the contractor, even in the case where the quantity of cement required is higher than the minimum specified above to achieve desired strength based on an approved design mix.) |
| 40 | All works upto plinth level |
| 41 | All works above plinth level upto floor V level |
| 42 | Providing and layingprecast machine moulded Cement ConcreteSolid blocks in Block Masonry of specified size with blocks of grade D (5.0) with minimum average compressive strength 5 MPa and blockdensity not less than 1800 kg/cum conforming to IS 2185 Part I nominal size in cement concrete 1 : 4 : 8 (1 cement : 4 Coarse sand : 8 graded stone aggregate 12 mm nominal size ) including scaffolding, raking out joints and filling joints with cement mortar, finishing neatly etc. up toPlinth Level all complete as per the direction of Engineer in Charge. |
| 43 | In Cement Mortar 1 : 6 (1 cement : 6 coarse sand). |
| 44 | Providing and laying precast machine moulded Cement Concrete Solid Blocks in Block Masonry of specified size with blocks of grade D (5.0) with minimum average compressive strength of 5 MPa and block density not less than 1800 Kg/cum conforming to IS 2185 Part-I in cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate of 12 mm nominal size ) including scaffolding, raking out joints and filling the joints with cement mortar, finishing neatly etc. above Plinth Level up to any Floor Level complete as directed by the Engineer in charge. |
| 45 | In Cement Mortar 1 : 6 (1 cement : 6 coarse sand). |
| 46 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.ird course of half brick masonry. |
| 47 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). |
| 48 | Second class teak wood |
| 49 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 50 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. |
| 51 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 52 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 53 | Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) : |
| 54 | Rectangular or square. |
| 55 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 56 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 57 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 58 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 59 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 60 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 61 | 300x10 mm |
| 62 | 150x10 mm |
| 63 | Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 64 | 100 mm |
| 65 | 75 mm |
| 66 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 67 | Twin rubber stopper |
| 68 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge |
| 69 | Extruded section profile size 48x40 mm |
| 70 | Providing and fixing to existing door frames. |
| 71 | 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 72 | Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 73 | Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.) |
| 74 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 75 | Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) |
| 76 | Providing and fixing 12 mm thick panelling in aluminium shuttersfor doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). |
| 77 | Marine plywood conforming to IS: 710 |
| 78 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 79 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. |
| 80 | 80x1.25 mm M.S. laths with 1.25 mm thick top cover. |
| 81 | Providing and fixing ball bearing for rolling shutters. |
| 82 | Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured). |
| 83 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 84 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 85 | Extra for using Galvanized platingover hot finished welded type tubes. |
| 86 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 87 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 88 | 40 mm thick with 20 mm nominal size stone aggregate |
| 89 | Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. |
| 90 | 18 mm thick. |
| 91 | Providing and fixing glass strips in joints of terrazzo/ cement concrete floors. |
| 92 | 40 mm wide and 4 mm thick. |
| 93 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kgper sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 94 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 95 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 96 | Size of Tile 600x600 mm |
| 97 | Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3kg/sqm |
| 98 | Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. |
| 99 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. |
| 100 | Size of Tile 600x600 mm |
| 101 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade(0.10 kg of hardener and 0.20 kg of resin per kg), including filling/grouting and finishing complete as per direction of Engineer-in-charge. |
| 102 | Size of Tile 600x600 mm |
| 103 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. |
| 104 | Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent |
| 105 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 106 | Granite work |
| 107 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. a)Granite of any colour and shade |
| 108 | Area of slab over 0.50 sqm |
| 109 | Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete |
| 110 | Extra for providing and laying matt finished / antiskid vitrified tile vide item No.53a) |
| 111 | Providing and fixing stone slab with table rubbed, edges rounded and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. |
| 112 | Granite Stone of approved shade |
| 113 | Providing and fixing2 mm thick antistatic polyvinyl chloride sheet of superior quality (Armstrong or equivalent) in flooring and skirting in approved pattern on a smooth and damp proof surface using rubber based adhesive of approved quality and manufacturer like Dunlop S-758, Fevicol SR 998 or equivalent including providing with cup washersalong with periphery of the room or at the required places for earthing of flooring and rolling with light wooden roller weighing about 5kg all complete as directed by the Engineer-in-charge, in approved colour and shade |
| 114 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i)Single socketed pipes. |
| 115 | 110 mm diameter |
| 116 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. |
| 117 | 110 mm bend 87.5 |
| 118 | 110 mm Shoe |
| 119 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 120 | 110 mm |
| 121 | Providing & fixing Terracottaroofingtiles with ceramic coatingof 10 mm nominal thickness of approved size and pattern of approved manufacture over raised cememt mortar band with the help of concrete nails etc. all complete as the direction of Engineer in charge. (Raised band will be measured separately) |
| 122 | Providing & laying Terracottaroofingtilesridgewith ceramic coating of 10 mm thickness and of approved size andpattern ofapproved manufacturefixing with concrete nails, washers, silicon adhesive etc. complete as the direction of Engineer in charge |
| 123 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \"T\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \"T\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \"T\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 124 | GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece. |
| 125 | Providing and fixing 0.50 mm (+ 0.05 %)troughed profile aluminium roofing sheet of marine 5052 grade (size, shape and pitch of corrugation as approved by Engineer-in-charge) with polyester bottom coat 8-9 microns and top coat 5micron primer + 20micron PVDF coating. Sheet should not have any scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using anti-corrosive screws with necessary seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 126 | Providing and fixing aluminium ridges of overall width 40.6mm of marine 5052 grade fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers and anti-corrosive screws all complete. |
| 127 | Providing and fixinguPVC rain water gutter of cross section 160mmx100mm and thickness 3mm, with leaf guard including necessary PVC clamps, adapter, coupler, centre drop, end drop, end cap, screws etc. all complete as per the directions of Engineer-in-charge |
| 128 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect. |
| 129 | SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer |
| 130 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2). |
| 131 | 12 mm average thickness. |
| 132 | Providing and laying FRP lining water proofing treatment in sunken portion of WC\"s bathroom, terrace etc. as per the manufacturers specification. The application shall be done only after cleaning of surface, there after applying One coat of resin mixed with pigments shall be applied over the cleaned surface uniformly. Fibre glass layer shall be placed over that in required thickness and density as per manufactures specification. Top coat of resin mixed with pigment shall be then applied in uniform thickness and colour.The rate shall be inclusive ofpreparation of surface,grouting over slab & side wall, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry and testing of applied area complete.. |
| 133 | Providing and fixing PVCball valve of approved quality of dia 110mm for unplasticised rigid PVC pipes including jointing with solvent cement etc. complete. |
| 134 | 12 mm cement plaster of mix : |
| 135 | 1:6 (1 cement: 6 fine sand) |
| 136 | 15 mm cement plaster on the rough side of single or half brick wall of mix : |
| 137 | 1:6 (1 cement: 6 fine sand) |
| 138 | 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6mm thick cement plaster 1:6 (1 cement: 6 fine sand). |
| 139 | 12 mm cement plaster finished with a floating coat of neat cement of mix : |
| 140 | 1:3 (1 cement: 3 fine sand) |
| 141 | Neat cement punning |
| 142 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 143 | 12 mm thick plain cement mortar bands in cement mortar 1:4 (1 cement: 4 fine sand) : |
| 144 | Raised Band |
| 145 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. |
| 146 | New work (two or more coats) over and including water thinnable priming coat with cement primer. |
| 147 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 148 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). |
| 149 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade |
| 150 | New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). |
| 151 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc. complete. |
| 152 | On steel work |
| 153 | Providing and applying cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 154 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. |
| 155 | Two coats. |
| 156 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 157 | Two or more coats on new work. |
| 158 | Melamine polishing on wood work(one or more coat) |
| 159 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. |
| 160 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. |
| 161 | Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand/6mm aggregate, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer\"s specifications & direction of Engineer in-Charge. |
| 162 | 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern. |
| 163 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 164 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 165 | White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 166 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board |
| 167 | 510x1040 mm bowl depth 250 mm. |
| 168 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. a)Flexible pipe |
| 169 | 40 mm dia |
| 170 | Providing and fixing PVC floor trap of approved quality and make, with PVC screwed down or hinged grating, with or without vent arm couple, of self cleansing design of 150 X 150mm size and locking with PVC, half round strainer with provision of 1 to 3 waste inlets & outlets of range 75 to 40mm dia. for different appliances , all complete including cost of cutting and making good the walls and floors etc. |
| 171 | 100mm inlet and 75mm outlet |
| 172 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : |
| 173 | Rectangular shape 453x357 mm |
| 174 | Providing and fixingC.P. brass towel railcomplete withbrackets fixed to wooden cleats with CP brass screws. |
| 175 | 20mm dia towel rail of length 600mm with two C.P. brass brackets. |
| 176 | Providing and fixing toilet paper holder : |
| 177 | C.P. brass |
| 178 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 179 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : |
| 180 | Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 181 | Providing and fixing CP brass Urinal push cock of approved quality |
| 182 | 15 mm nominal bore, weighing not less than 550 gms |
| 183 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 184 | Providing and fixing 15 mm dia C.P brass health faucet including CP brass connection pipe of required length, holding clamp etc. of best quality and make as approved by Engineer - in - charge. |
| 185 | Jaguar Brass Health Faucet with Long CP Flexible Tube (Chrome Finish, 15 mm) |
| 186 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 187 | 20 mm nominal outer dia. Pipes. |
| 188 | 25 mm nominal outer dia .Pipes. |
| 189 | 32 mm nominal outer dia. Pipes. |
| 190 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. |
| 191 | 20 mm nominal outer dia .Pipes. |
| 192 | 25 mm nominal outer dia .Pipes. |
| 193 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work |
| 194 | 32 mm nominal outer dia. Pipes. |
| 195 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : |
| 196 | 25 to 40 mm nominal bore |
| 197 | 50 to 80 mm nominal bore |
| 198 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 199 | 25 mm nominal bore |
| 200 | 20 mm nominal bore |
| 201 | 32 mm nominal bore |
| 202 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 203 | 100 mm diameter |
| 204 | Providing and fixing lever operated , quarter turn, forged CP brass ball valve of 32mm nominal bore all complete as per the directions of Engineer-in-charge. |
| 205 | Supplying, installing and making connection to wall mounted \"Roof Rainwater Filter\" of approximate size 600mmx400mmx250mm with inlet and outlet 110mm dia having nylon filter element, 130micron filtration, safety valve, backwash nipple, 50mm dia flush drain, outlet and flush valve etc. all complete as per the directions of the Engineer-in-charge. |
| 206 | Supplying, installing \"Atmospheric Water Generator\" of 100 litres water making capacity \"Dew Point Super\" of \"Liquipro\" or equivalent, including cost of 4 filters to be replaced after one year and AMC of one year beyond the initial warranty period of 12 months all complete as per the directions of Engineer-in-charge. |
| 207 | Providing and fixing uplasticised PVC connection pipe with brass unions : a)45 cm length |
| 208 | 15 mm nominal bore |
| 209 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. |
| 210 | 15 mm nominal bore |
| 211 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 212 | 15 mm nominal bore. |
| 213 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : |
| 214 | 15mm nominal bore |
| 215 | Providing and fixing PTMT grating of approved quality and colour. a)Rectangular type with openable circular lid. |
| 216 | 150 mm nominal size square 100 mm diameter of the inner hinged round grating. |
| 217 | Supplying and fixing 600m x600mm size square CI cover with frame of total weight not less than 50 kg all complete as per the directions of Engineer-in-charge. |
| 218 | Providing and fixing C P brass soap Dish Holder of approved shape and size |
| 219 | Providing and fixing unplasticized rigid polyvinyl chloride soil, waste and vent pipe with socket (conforming to IS 4985-1988) of pressure class of 4Kg/Sq.cm. Including jointing the pipe with solvent cement |
| 220 | 75 mm diameter |
| 221 | 110 mm diameter |
| 222 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. |
| 223 | 75x75x75 mm single tee with door |
| 224 | 110x110x110 mm single tee with door |
| 225 | 75x75x75 mm single tee without door |
| 226 | 110x110x110 mm single tee without door |
| 227 | 75 mm bend |
| 228 | 110 mm bend |
| 229 | 75 mm vent cowl with wire mesh |
| 230 | 110 mm vent cowl with wire mesh |
| 231 | Providing and fixing 110mm dia PVC pipe end cap provided with insect-proof net all complete as per the directions of Engineer-in-charge. |
| 232 | Supplying, installing and making connection to ready made Polyethylene septic tank 2300 long and 1000mm dia, thickness 10mm with three chambers, two manholes having 30 flush per day(approximate 12 users) capacity (Type -3 of \"United\" or equivalent) all complete as per the directions of Engineer-in-charge. |
| 233 | Providingand fixing PVC manholes of Supreme [Ultra 315] or equivalent with 110mm inlets and outlets in required profiles including fixing in requiredposition , level and providing pvc cover with frame of supreme drain ultra cover (HW) or equivalent etc. as per the direction of Engineer in charge. |
| 234 | Providing and fixing PVC vertical risers of Supreme Ultra or equivalent of height 0.30mtr for the extra depth ofpvc manholes |
| 235 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round PVC pipes including bed concrete as per standard design: |
| 236 | 110 mm diameter PVC pipe |
| 237 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : a)100x100 mm size P type |
| 238 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 239 | Constructing soak away pit using polyethylene bell shaped soak away ringwith 50 to 75 mm size granular materials filled all-round the ring. The periphery of the granular material all-round shall be covered with non-woven Geotextile sheet. Earthwork in excavation shall be measured under the relevant item. |
| 240 | Polyethylene bell shaped soak away ring of top dia 500mm, bottom dia 1200mmand height 750mm |
| 241 | Granular materials / aggregate 50 to 75mm size |
| 242 | Geotextile of 900 GSM laid in two layers. (Each layer will be measured for payment) |
| 243 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 244 | For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 245 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 246 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 247 | Pre-laminated particle board with decorative lamination on both sides. |
| 248 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 249 | With float glass panes of 4.0 mm thickness |
| 250 | With float glass panes of 5.0 mm thickness |
| 251 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. |
| 252 | With brass cover plate minimum 1.25 mm thickness. |
| 253 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete. |
| 254 | 255 x 19 mm |
| 255 | Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 256 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). |
| 257 | Providing and fixing sun control film of thickness 1.5mm of approved make, colour and with self adhesive to glazed windows, doors and partitions as approved and as per the directions of the Engineer-in-charge. |
AI Tender Summary
Tender Timeline
Oct 18, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedOct 29, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 01, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender