Orissa Lift Irrigation Corporation Limited has published Revival And Energisation Of Kuagola L.I. Project Under Jamankira Block In Sambalpur District Of L.I. Division, Sambalpur. Submission Date for this Tender is 27-10-2021. Lift Irrigation Tenders in Jamankira Odisha. Bidders can get complete Tender details and download the document.
Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
1 | 25-Oct-2021 | Corrigendum Notice | Technical Bid | 27-10-2021 |
Sl. No. | Item Description |
1 | Part-A |
2 | Earthwork in excavation of foundation in hard soil including dressing & levelling of bed within initial lead of 50mt. & lift of 1.5mtr etc complete as per the direction of the Engineer-incharge. |
3 | Filling in foundation & plinth with sand including watering & ramming etc complete as per the direction of the Engineer-incharge. |
4 | Cement concrete (1:4:8) with 4cm size h.g.b. crusher broken metal of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc. complete as per the direction of the Engineer-incharge. |
5 | Brick work with K.B. Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6)in foundation & plinth complete as per the Engineer-incharge |
6 | Cement concrete (1:2:4) with 12mm size black h.g.b. crusher broken chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc complete as per the direction of the Engineer-incharge. |
7 | Rigid smooth centering & shuttering for R.C.C. works including false work & dismateling then after including cost of materials in ground floor complete an directed by the Engineer-incharge. |
8 | Labour charges for MS reinforcement for RCC work including cutting, bending & tying the grills and placing in position including cost of binding wire 18 to 20 gauge & HYSD steel bar ( FE 415/ FE 500 ) |
9 | R.C.C. work in C.C. (1:2:4) including hoisting & laying & curring for 28days using 12mm. Size clean black hard granite crusher broken chips of approve quality and from approve quarry including cost taxes conveyance charges of all materials to the worksite with supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
10 | 12mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
11 | Cement punning over plastering including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
12 | Writing charge of required information and data on both side of the transperancy pillar including supplying of approved paints and required material for writing etc. complete as per the direction of the Engineer-incharge. |
13 | Fitting of un plasticised 160 mm dia meter diaPVC Pipe for all classes including jointing the pipe with solvent cement by non-head application method including fitting and fixing of required no. of PVC Tee for outlet and PVC Shaddle and PVC Riser nipple for fitting air valve, equal Tee etc. including cost of PVC Pipe, cost of Solvent Cement, transportation of Pipe complete including conveyance pipe from village to worksite and testing of pipe line etc. complete as per the direction of the Engineer-incharge. |
14 | Supplying of 160 mm dia unplasticised rigid UPVC pipe ivory grey in colour having specific gravity of 1.40 to 1.46 gms/ cc of straight length of 6 (six) meter for potable water supplies conforming to IS - 4985/ 2000 of BIS - Ammendment - 2 read with Table - 1 of IS - specification bearing ISI marks for working pressure Cl - IUPVC pipe to withstand pressure of2.5 kgf/cm² respectively & the specification and manufacturer"s name should be prominently marked on body of each pipe as per the latest Ammendment of IS - 4985. It includes the cost of sockets in case of plain ended pipe. PDI test are to be conducted and should be marked on body of each pipe and report is to be obtained from CIPET, Bhubanweswar, necessary approval of authority including transportation towork site in complete shape |
15 | Filling the foundation and plinth with excavated material as directed by the Engineer-incharge. A) Hard Soil |
16 | Monoblock pumpset total head of 18 mtr capable to discharge 1700 LPM with 10 HP/9.40 KW squirrel cage induction motor fitted with bronze impeller TB-2 of iS 318/1981, companion flanges & class "F" insulation suitable for operation 415 volt + 6% - 15%, 3 phasde, 50 Hz AC power supply, suction/delivery = 100x100 mm with BEE star rated energy efficiency pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership network for easy availibility of spares |
17 | Control panel with automatic star delta starter sheet steel enclosure vsuitable for operation of squirrel cage induction motor up to 10 HP with 16 Amp.(AC-3) duty contractor at 415 volt+6%-15%, 3 phase, 50 Hz AC supply with over load relay range 8.9 to 13.5 Amp & No volt coil with electronic timer suitable for operation at voltage range of 300 to 440 V. The starter should provide dependable protection against over load and single phasing fitted with Volt meter, Ammeter, MCB in complete shape including indicator lamp |
18 | Motor Hood (size 0.45x0.45x0.60 mtr ) made with 18 SWG cold rolled mS sheet with one coat of red oxide primer and two coats of smoke gray / navy blue enamel paint both side (inside & outside) suitable to cover centrifugal monoblock Pump set from 10 to 15 HP and having provision for attachment with the groves on rear side of the panel board |
19 | Base frame for panel ( size 0.40x0.20 m )and for Motor ( size 0.50x0.27 m ) made with 3" size MS channel having suitable holes for fitting of Panel board and different size & make 3 phase centrifugal monoblock pumpset from 10 to 15 HP, coloured with one coat of red oxide primer and two coats of smoke gray enamel paint |
20 | 3 x 16 mm² Tarpedore cable XLPE ( cross link polyethylin ) confirming to IS: 7098 (Part-II) including laying below 0.90 mtr of the ground and filling the excavated materials including watering and ramming |
21 | 100 mm dia nominal bore GI pipe having wall thickness 4.5 mm electrical resistance welded of medium class confirming to IS - 1239 (pt - 1 of 2004) with socketed at one end and the other end protected with plastic thread protector. The socket confirming to IS - 1239 (pt - II / 1992) with latest amendments in random length of 4 to 7 mtrs. Each pipe should bear ISI certification& manufacturer"s name/ trademark |
22 | 100 mm dia GI Bend IS No. 1239(pt-II/1992) |
23 | 100 mm dia GI flange IS No. 6392 / 1971 |
24 | 100x100x25 mm GI Tee with plug for priming |
25 | 160 mmx100 mm PVC/G.I./M.S. Reducer |
26 | 100mm C.I. Foot Valve should be of swing type friction less with single disc confirming to iS - 4038/1979 of reputed brand |
27 | 100mm C.I. N.R. Valve double flanged swing type PN - 1.0 as per IS:5312 part - I with by-pass arrangement |
28 | 50 mm dia CI AR valve with saddle and riser pipe confirming to IS 14845 with ISI mark |
29 | 160 mm dia PVC end cap ( 10 kgf/cm²) confirming to IS - 4995/1988 with latest ammendment |
30 | 160x160x110 mm PVC/GI Raiser tee set with bend closing and opening arrangement |
31 | 160 mm dia PVC coupler ( 4 kgf/cm²) agricultiral PVC fittings confirming to IS - 4995/1988 with latest ammendment |
32 | Construction of out let for Tee Tank |
33 | Supply of small T & P Kit comprising of hand gloves - 1 pair, tester - 1 no, 8" cutting plier - 1 no, 12" sly wrench - 1 no, 12" screw driver - 1 no, 24/27 & 21/23 DE spanner - 2 nos, 24/27 & 21/23 Ring spanner - 2 nos of Taparia make |
34 | Labour charges for installation of 12.5 HP MB Motorsincluding transportation from village to work site, fitting & fixing of base frame, fitting & fixing suction and delivery pipe to motor, other fitting materials including cutting, welding etc. complete as per the direction of the Engineer-incharge. |
35 | Part-B |
36 | Construction of 3 phase 11 KV Line as per REC standard confirming to RE Rules 1956 with 300Kg. 9 mtrs.long PSC Pole ( cost excluded ) support in 80Mtrs. Span 55 sqm. AAA Conductor, 11 KV "V" cross arm with required nos.of 11KV T &C disc.Insulators and 11KV Pin insulator,carping & padding of poles, danger board at each pole,anticlimbing devices. Stay set at each bending Point and double stay at end point with 18mm G.I. H.T. Stay, concreting of stay with anchor plate,guarding at road crossing etc. including cost of materials,labours, transportation, inspection and commissionng etc. complete. |
37 | Cost of LT line with 35 mm² AB Cable 3 phase 4 wire on 8 mtr x 200 kg PSC pole ( 30 mtr span ) including distribution box and pearsing connector ( excluding pole cost ) |
38 | Construction & erection of 11/0.416 KV, 25 KVA (BIS level-II) D.P.sub-station with out transformer confirming to RE Rules,1956 mounted on 2.8 Mtr. Long structure, supported in 300 Kg. 9 Mtr. Long PSC pole,transformer mounting channel & top channel made 0f 2.8 Mtr. Long 100x50x6 mm M.S. channel, transformer belting on 2.8 Mtr. long 50 x 50 x 5 mm M.S. Angle(all REC.SPN. Std.F-3) with all accessorieslike 3 pole 11 KV HG Fuse (F-5) & A.B.Switches(F-9) both mounted on 2.8M long 75x40x6 mm M.S. Channel and supported by 1.0 mtr. long 50x50x5 mm M.S. Angle with 3 nos. 11 KV lightening Arrestors and Distribution box for 25 KVA S/S, Pipe earthing(F-2), including cost of 50 sqmm 3.5 Core PVC cable carping & padding of Poles, Danger board at each Pole, Anti Climbing Devices & all other necessary fittings i.e. FI Pipe Earthing 40 Dia Medium gage 3 mtrs. Long,fixing of stay set with 0.5 Cum cement concret foundation 1:3:6 of required size , L.T.Distribution box including Kit Kat fuse with MCCB (As per DISTCOM specification) 3 1/2 x 35 sqmm. PVC Cable , , Bolts, Brackets, Cable sockets etc. including cost of all materials, labour, transportation complete with liasioning for testing, inspection and commissioningincluding painting in Navy Blue colour band with inscription of OLIC in each Pole. |
39 | Cost of Transformer 25 KVA Transformer (11/0.4 KV ) |
40 | Materials for 11KV Cut point without pole |
41 | Material for 11 KV Line DP cutpoint without pole |
42 | 9 mtr 300 kg PSC pole |
43 | 8 mtr 200 kg PSC pole |
44 | Barbed wire fencing with metal spreading |
45 | Spike provisin |
46 | Electrical Earthing |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail