|
| 1 | Pigeon Hole Lockers | Size: 1950x825x450mmShould be made of 0.7 & 0.8mm thick CRC sheets, 8 or 18 holes with all metal surfaces/parts should be given antirust treatment and be powder coated. |
| 2 | Book Racks(Single Sided Wood & Steel Book Rack Base Unit) | Overall Dimensions of Single Sided Wood & Steel Book Rack Base Unit should be 900mm(W)x300mm(D)x1890mm(H). Rigid Knockdown construction. Back panel should be up to the bottom of third rack for additional rigidity. Racks, Back panel & Skirting: CRCA 0.8 mm thickness. Side panels: 25 mm thick pre laminated particle board (PLB) with laminate on both sides. Stackability should have add-on units width wise to form a bank of racks having a common side panel. Bottom plus four fixed racks plus five storage levels. Each rack should be provided with stiffener at bottom for strength. Uniformly distributed load capacity per each full shelf should be 80 Kg minimum. Rack back stiffener should be there at the rear side of the racks. These are to support books on the rear side. Label Holder on each main unit to insert labels for identification. Finish should be Epoxy polyester powder coated to the thickness of 50 microns. The product must be Grrenguard/ IAQ/ GRIHA/ Bifma Level Certified. The certificate must be from an authorised source only. |
| 3 | Book Racks (Single Sided Wood & Steel Book Rack Add on Unit) | Overall Dimensions of Single Sided Wood & Steel Book Rack Add on Unit should be 900mm(W)x300mm(D)x1890mm(H). Rigid Knockdown construction. Back panel should be up to the bottom of third rack for additional rigidity. Racks, Back panel & Skirting: CRCA 0.8 mm thickness. Side panels: 25 mm thick pre laminated particle board (PLB) with laminate on both sides. Stackability should have add-on units width wiseto form a bank of racks having a common side panel. Bottom plus four fixed racks plus five storage levels. Each rack should be provided with stiffener at bottom for strength. Uniformly distributed load capacity per each full shelf should be 80 Kg minimum. Rack back stiffener should be there at the rear side of the racks. These are to support books on the rear side. Label Holder on each main unit to insert labels for identification. Finish should be Epoxy polyester powder coated to the thickness of 50 microns. The product must be Grrenguard/ IAQ/ GRIHA/ Bifma Level Certified. The certificate must be from an authorised source only. |
| 4 | Book Racks (Double Sided Wood & Steel Book Rack Base Unit) | Overall Dimensions of Double Sided Wood & Steel Book Rack Base Unit should be 900mm (W)x590mm(D)x1890mm(H). Rigid Knockdown construction. Back panel should be up to the bottom of third rack for additional rigidity. Racks, Back panel & Skirting: CRCA 0.8 mm thickness. Side panels: 25 mm thick pre laminated particle board (PLB) with laminate on both sides. Stackability should have add-on units width wiseto form a bank of racks having a common side panel. Bottom plus four fixed racks plus 10 storage levels. Each rack should be provided with stiffener at bottom for strength. Uniformly distributed load capacity per each full shelf should be 80 Kg minimum. Rack back stiffener should be there at the rear side of the racks. These are to support books on the rear side. Label Holder on each main unit to insert labels for identification. Finish should be Epoxy polyester powder coated to the thickness of 50 microns. The product must be Grrenguard/ IAQ/ GRIHA/ Bifma Level Certified. The certificate must be from an authorised source only. |
| 5 | Book Racks (Double Sided Wood & Steel Book Rack Add on Unit) | Overall Dimensions of Double Sided Wood & Steel Book Rack Add on Unit should be 900mm (W)x590mm(D)x1890mm(H). Rigid Knockdown construction. Back panel should be up to the bottom of third rack for additional rigidity. Racks, Back panel & Skirting: CRCA 0.8 mm thickness. Side panels: 25 mm thick pre laminated particle board (PLB) with laminate on both sides. Stackability should have add-on units width wiseto form a bank of racks having a common side panel. Bottom plus four fixed racks plus 10 storage levels. Each rack should be provided with stiffener at bottom for strength. Uniformly distributed load capacity per each full shelf should be 80 Kg minimum. Rack back stiffener should be there at the rear side of the racks. These are to support books on the rear side. Label Holder on each main unit to insert labels for identification. Finish should be Epoxy polyester powder coated to the thickness of 50 microns. The product must be Grrenguard/ IAQ/ GRIHA/ Bifma Level Certified. The certificate must be from an authorised source only. |
| 6 | Sofa and Tables for For Central Atrium | Sofas with power plug options + tables to be customised4 Sofas (Sofa dimensions: Dimensions H x D (cm): 79 X 70.5, Upholstery Material: fabric, Leg Material: Plywood, Frame Material: Plywood, with power plug option(4 each) |
| 7 | Table A | Convertible into L-shaped table with extra storage W X D X H = 165 cm X 75 cm X 76.5cmPrimary Work Surface- should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Should have 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Secondary Work Surface- Should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel- should be made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Understructure- Should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal- Should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts should be made of 25mm thick MDF one side pre-laminate board confirming toIS-14587:1998 with 0.4mm PVC membrane pressed on to topPedstal construction should be BOX-BOX-FILE type which Uses powder coated 400 MM long metalPanel Drawer Slides. Drawer extension should be 325 MM.Drawers should have a soft closing & anti slam mechanism.Handles should be provided for ease of opening.Pedestal should be provided with lock for security. |
| 8 | Table B | The system shall be a desk-based system with a platform understructure made up of a combination of MS. Tubes and plates. Legs are fabricated by Argo Shield welding MS ERW Tube 40 mm x 40 mm x 1.2mm thk , 50 mm x 25 x 1.2 mm thk, with perforated metal modesty in between are connected to the understructure with the help of PDC Connectors to provide a stable and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Worktop shall be made of 25MM thick Pre-Laminated Board conforming to IS: 12823. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be complete with provisions for screen mounting as well as for wire management on the workstation. Provisions for fixing of the switches shall be on the wire tray/channel. Access flaps with soft closing technology shall be provided on the table tops to access the switch points on the tray. Rectangular worktop of size 1350mm W x 600mm with return desk of 900x450mm. Wire Management shall be a part of the understructure and in the form of enclosed metal tray to provide concealed wire management throughout the cluster formation. Wire riser legs with cover shall be provided as per the layout structure. 19 mm thk fabric screens are provided along main spine & acrylic finished clip-on screens along depth. The screens provided shall be complete with its set of PDC clamps for fixing on the worktop. Metal Front pedestal shall be of free standing & central locking of size 390 mm w x 435 mm d x 646 mm ht, 2drawer = 1box+1file. |
| 9 | Chair B | Strictly as per the Specification Document |
| 10 | Table C | The top should be made from 25 mm thick pre- laminated board. All the edges should be sealed with 2 mm thick PVC edge band all around. Side panels should be made from 25 mm thick pre- laminated paticle board. All the edges should be sealed with 2 mm thick PVC edge band on theuser side and 0.8 mm on the top and bottom side .The side panels should have 2 glide screws each for levelling of the desk. Modesty panel should be made from 18 mm thick pre- laminated particle board. All the edges should be sealed with 0.8 mm thick PVC edge band all around. Freestanding Pedestal should be made from 18 mm pre- laminated particle board with a combination of 2 mm and 0.8 mm PVC edge band on all the exposed surfaces as per requirement. The drawers may be provided with suitable slides for smooth operation. All the pedestal drawers should be centrally locked with a single key. |
| 11 | Table D | Size:\"1800x2100x750Primary Work Surface- should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Should be made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Secondary Work Surface- Should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel- Should be made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Understructure- Should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded should be with matching 2 mm thick PVC lipping.Integrated Pedestal- Should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded should be with matching 2 mm thick PVC lipping. Drawer fronts should be made of 25mm thick MDF one side pre-laminate board confirming toIS-14587:1998 with 0.4mm PVC membrane pressed on to topPedestal construction should be BOX-BOX-FILE type which Uses powder coated 400 MM long metalPanel Drawer Slides. Drawer extension should be 325 MM.Drawers should have a soft closing & anti slam mechanism.Handles should be provided for ease of opening.Pedestal should be provided with lock for security. The product must be either Grrenguard/IAQ/GRIHA/Bifma Level Certified. |
| 12 | Chair D | Strictly as per the Specification Document |
| 13 | Visitor Chairs A | \"seat/back assembly : the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with pure leather and moulded high resilience (hr) polyurethane foam of density 45±2 kg/m3,and hardness load 16 ± 2 kgffor 25% compression. the cushioned back should bemade of pu foam with insitumoldedmse.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with pure leather.seat size : 47.6 cm. (w) x 49.2 cm. (d)back size : 46.5 cm. (w) x 59.5 cm. (d)visitor tubular frame: the tubular frame should becantilever type and made of ø2.54± 0.03 cm x 0.02 ± 0.016cm thick ss 202 tube. the back should beconnected to frame through chrome plated high pressure die case connector piece. Overall Dimensions of Chair-Seat Height -46.2 cm. Height -98.2 cm.Width & Depth of Chair as measured from base - Width-60.9 cm and Depth-64.7 cm. The product must be either Greenguard /IAQ/GRIHA/Bifma Level Certified. |
| 14 | Table E | Primary Work Surface- Should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Should have 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Secondary Work Surface- Should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel- Should be made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Understructure- Should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal- Should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded should be with matching 2 mm thick PVC lipping. Drawer fronts be made of 25mm thick MDF one side pre-laminate board confirming toIS-14587:1998 with 0.4mm PVC membrane pressed on to topPedstal construction should be BOX-BOX-FILE type which Uses powder coated 400 MM long metalPanel Drawer Slides. Drawer extension to be 325 MM.Drawers should have a soft closing & anti slam mechanism.Handles should be provided for ease of opening.Pedestal should be provided with lock for security. The product must be either Grrenguard/IAQ/GRIHA/Bifma Level Certified. |
| 15 | Chair E | Strictly as per the Specification Document |
| 16 | Visitor Chairs B | \"seat/back assembly : the cushioned seat should bemade of injection molded plastic outer & inner. plastic inner should beupholstered with pure leather and moulded high resilience (hr) polyurethane foam of density 45±2 kg/m3,and hardness load 16 ± 2 kgffor 25% compression. the cushioned back should bemade of pu foam with insitumoldedmse.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with pure leather.seat size : 47.6 cm. (w) x 49.2 cm. (d)back size : 46.5 cm. (w) x 59.5 cm. (d)visitor tubular frame: the tubular frame should becantilever type and made of ø2.54± 0.03 cm x 0.02 ± 0.016cm thick ss 202 tube. the back should beconnected to frame through chrome plated high pressure die case connector piece. Overall Dimensions of Chair-Seat Height -46.2 cm. Height -98.2 cm.Width & Depth of Chair as measured from base - Width-60.9 cm and Depth-64.7 cm. The product must be either Greenguard /IAQ/GRIHA/Bifma Level Certified. |
| 17 | Sofa A | \"Seat & Body: Understructure: Understructure is made of combination of plywood & pinewood members. Plywood is 12±1mm thk. [moisture resistance &termile proof as per IS:303] & pinewood are cross section [22x25, 22x40, 25x75 & 25x100mm] are without major knots & defects on the surface. 3mm MDF is stapled on the seat front bottom vertical surface to get the surface to stick the foam. Dia. 3.8mm zigzag spring asly. is mounted on the seat structure with spring mounting plastic bracket for support & additional cushioning purpose. Elastic belt of 2\"\" width are used above the spring asly. to give good sagging effect. Non-woven fabric is stapled on the seat structure frame above the spring asly. to avoid the tearing of seat foam with the surface contact of metal spring. Back vertical surface is stapled with non-woven cloth to get surface to stick the foam. Complete understructure is made by gluing & stapling.Foam: Seat is made of PU foam with density 28 kg/m3 having an additional top layer of supersoft PU foam with density 18 kg/m3. Recron sheet of 230GSM is used above this foam. Seat front bottom vertical surface & back vertical surface is glued with the PU foam with density 22 kg/m3. Side vertical surface, body front taper vertical & top horizontal surface is glued with PU foam with density 16 kg/m3.Upholstry: Seat & body upholstry is made in the dual tone colour with fabric / fabric option & fabric / leatherite option.Back Top Cushion: Understructure: Understructure is made of combination 12±1mm & 6±1mm thk.Foam: It is made with supersoft PU foam with density 18 kg/m3.Upholstry: It is upholstred with fabric.These back top cushions are fitted with the seat & body structure with the chipboard screws. Qty. of back top cushion fitted with each. Packet: One packet per Qty. 1No. of each SKU. Each SKU is packed in the seperate packet.Power beam of 1200mm length to be provided.\" |
| 18 | Sofa B | Seat & Body: Understructure: Should be made of combination of plywood & pinewood members. Plywood should be 12±1mm thk. [moisture resistance &termile proof as per IS:303] &pinewoods to be cross section [22x25, 22x40, 25x75 & 25x100mm] and to be without major knots & defects on the surface. 3mm MDF to be stapled on the seat front bottom vertical surface to get the surface to stick the foam. Dia. should be 3.8mm zigzag spring asly. andbe mounted on the seat structure with spring mounting plastic bracket for support & additional cushioning purpose. Elastic belt of 2\" width should be used above the spring asly. to give good sagging effect. Non woven fabric should be stapled on the seat structure frame above the spring asly. to avoid the tearing of seat foam with the surface contact of metal spring. Back vertical surface should be stapled with non-woven cloth to get surface to stick the foam. Complete understructureshould be made by gluing & stapling.• Foam: Seat should be made of PU foam with density 28 kg/m3 having an additional top layer of supersoft PU foam with density 18 kg/m3. Recron sheet of 230GSM should be used above this foam. Seat front bottom vertical surface &back vertical surface should be glued with the PU foam with density 22 kg/m3. Side vertical surface, body front taper vertical & top horizontal surface should be glued with PU foam with density 16 kg/m3.• Upholstry: Seat & body upholstryshould be made in the dual tone colour with fabric / fabric option & fabric / leatherite option.Back Top Cushion:•Understructure: should be made of combination 12±1mm & 6±1mm thk.Foam: It should be made with supersoft PU foam with density 18 kg/m3.Upholstry: It should beupholstred with fabric.These back top cushions to be fitted with the seat & body structure with the chipboard screws. Each SKU should be packed in the seperate packet.Power beam of 1200mm length to be provided. |
| 19 | Workpod | \"BASE :The base-top should be made using 18mm Plywood (As per IS:303), and Natural Veneer pasted onto 4mm backing Plywood. The base-top should have a bidding of FSC-certified seasoned Teak-Wood finished with a clear matt coat of PUlacquer around the periphery. The base Under-structure should consists of Legs and Cross-members to be made with FSC-certified seasoned Teak-Wood. They should be connected using Epoxy Resin Based Adhesive and finished with a Clear Matt Coat of PU lacquer. The Under-structure and top should be assembled using alloy steel hardware (blackened & coated with rust preventive oil).BACK-FRAME:The Back-frame should have an Under-structure made of 18mm Plywood (As perIS:303). It should be covered with 06mm Plywood (As per IS:303) from the inside\". |
| 20 | Coffee Table A | Should be a centre table glass: it should be 12 ±0.3 mm thick black tinted toughened glassuv glued with bushes made in ss 202 grade for fixing with understructure. understructure: it should bea welded assembly made in ss202 grade having dia. 12±0.04 |
| 21 | Coffee Table B | Coffee Table of W X D X H = 120cm X 60cm X 40 cm |
| 22 | Tetris Modular Seating | \" SEAT :The seat should be made up of synthetic leather upholstered on PU slabstock foam of 6.5 cm (±0.5 cm It should be fitted to the upholstered wooden batten box by bolting from the inside.Holding plate should be made of HR Steel of 0.3 cm (±0,02 cm) thickness as per IS:2062 which should be bolted to the upholstered seat assembly.* SEAT SIZE : 42.0 cm. (W) x 42.0 cm. (D) CASING OF TETRIS:Casing of the flip type of Tetris should be made up of 01 cm (±0.02 cm) M.S. rod as per IS:9550. Casing should be powder coated (DFT 40-60 microns). Also casing should be coated with nano coat to improve the abrasion resistance of the surface.* CASING SIZE: 44.0 cm. (W) x 44.0 cm. (D) x 37.5 (H)WOODEN BATTEN BOX ASSEMBLY :Side panels of batten box should be made up of 0.9 cm (±0.05 cm) plywood as per IS:303. The four corners of batten box should be made up of solid wood which forms the radius. Bottom portion of batten box to be covered by 1.2 cm (±0.05cm) rubber wood panel which should be finished with a clear mall coat of PU lacquer.Sides of wooden batten box to be upholstered with synthetic leather with backing of PU slabstock foam of 0.6 cm.Upholstered wooden box should have option of flip in the reverse way to use it as desk surface by keeping it on the casing. |
| 23 | Reading Chair 1 | Seat / back: the seat sub-assembly should be made up of 1.2±0.1cm thk plywood upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The seat should be with option to tip-up when not in use. the back sub-assembly should bemade up of injection-moulded polypropylene inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The contoured back with width extension at the bottom should be designed to give comfort to lower back. The back flexing features allows the back to tilt by 9c±2\" to aid the user in adopting a comfortable reclining posture. Both these sub-assemblies should be fixed to the tubular structure. The product must be either Grrenguard/IAQ/GRIHA/Bifma Level Certified. |
| 24 | Reading Table | Table Top: Pre-Laminated Particle Board Frame: Mild Steel W X D = 320-350 cm X 100 - 150 cm |
| 25 | Reading Chair 2 | seat / back: the seat sub-assembly should bemade up of 1.2±0.1cm thk plywood upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The seat should be with option to tip-up when not in use.The back sub-assembly should be made up of injection-moulded polypropylene inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The contoured back should be with width extension at the bottom and should be designed to give comfort to lower back. The back flexing features should allow the back to tilt by 9c±2\" to aid the user in adopting a comfortable reclining posture. both these sub-assemblies should be fixed to the tubular structure,back size: 45.2cm (w) x 44.6cm (i-i) seat size: 47.0cm (w) x 50.0cm (d)tubular frame structure: the powder-coated 4 leg structure should be made of 2.2 ±0.03cm dia x 0.25 ±0.02cm thkm.s.e.r.w. tube front and rear leg welded along with connecting tube made of 1.9 ±-0.02cm dia x 0.2 ±0.016cm thkm.s.e.r.w. tube to form the tubular frame assembly. the legs should beprovided with injection-moulded adopter bush in black nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use_ the chairs can be stacked horizontally when not in use_Polyurethane foam: the polyurethane foam should be moulded with density = 70.0 ±8.0 kg/m3 and hardness = 20 ±2 for seat & 16 ±2 for back at 25% compression.armrests: the armrest structure should bemade up of 2.2 ±0.03crn dia x 0.25 ±0.02cm thkm.s. e r.w. tube welded to the tubular frame structure and having a scratch-resistant tant abs arm top |
| 26 | Reading Table Round A | \"WORKTOP (PU) Worktop should be made of 25mm MDF OSR with pu matt finish on top side. Hardness on top surface to be 2H.Worktop should be made of 25mm MDF OSR with 0.4mm membrane foil on top surface. UNDER-STRUCTURE: The under-structure should consist of an InnerTube Assembly with Top Plate, for Worktop Mounting, & an Outer Tube Assembly with Round Plate. The Inner & Outer Tube Assemblies should be telescopically connected. The Top Plate should be made of 5mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062) & the bottom plate to be made of 8mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062). The Inner Tube Assembly should be made of 082.5 x 2thk ROUND ELECTRIC RESISTANCE WELDED Tubes (ERW) (As per IS:7138) and 8mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062) welded together using TUNGSTEN INERT GAS Welding. The Outer Tube Assembly should be madeof 089 x 2.5 thk and ROUND ELECTRIC RESISTANCE WELDED Tubes (ERW)(As per IS:7138) and 8mm thk HOT ROLLED Steel Plates (HR) (As per IS:2062) welded together using TUNGSTEN INERT GAS Welding. The whole structure to be EPDXY POLYESTER Powder Coated (DFT 40-60 microns). The product should have a knock-down construction. It should be assembled using alloy steel hardware (blackened & coated with rust preventive oil).\" |
| 27 | Reading Chair 3 | \" SHELL : The seat-back should be made of 15mm Plywood (As per IS:303) panels connected using Brackets made from 3mm Hot Rolled Steel Plates (HR) (As per IS:2062). The Steel Brackets should be Epoxy Polyester Powder Coated (DFT 40-60 microns). 25mm PU slab-stock foam to be pasted onto both sides of the shell and should be picnhed together to achieve the radius along the periphery. It should be upholstered in Leatherette.SEAT CUSHION : The seat-cushion should be made using 50mm PU slab-stock foam and should be upholstered in Leatherette. It should be held in place with hook and loop tape stitched to it\"s bottom side.UNDERSTRUCTURE : The understructureshould be made of FSC-certified seasoned Teak-Wood finished with a clear matt coat of PU Lacquer. Understructure members to be glued together using Epoxy Resin Based Adhesive. The shell should be fixed to the understructure using alloy steel hardware (blackened & coated with rust preventive oil).\" |
| 28 | Reading Table Round B | Height should be 750mm.Table should have metal chrome plated understructure for strudiness. Glass top should have thickness of 12mm and should be tempered glass. |
| 29 | Magazine Periodical Display | Overall Dimensions of All Steel Periodical Display Rack should be900mm(W)x450mm(D)x1830mm(H). Rigid Knockdown construction, Panels should be made from CRCA 0.6 mm thick and front frame should be made from CRCA 0.8 mm thick. CRCA D grade as per IS 513. There should be 5 level racks, Display tray should be suitable for fullscape size magazines, periodicals, aesthetically appealing metal tray at an angle for easy viewing. Receding facility to access the storage behind. Sliding on plastic rollers. Behind storage shelving each of 5 level should have a behind storage shelf. Uniformly Distributed Load capacity per each shelf should be 40 kg. Leveler should be screw type with hex plastic base and finish should be epoxy polyester powder coated to the thickness of 50 microns. The product must be either Grrenguard/IAQ/GRIHA/Bifma Level Certified. |
| 30 | Standing Newspaper Tables | 2 sided as per standard specifications |
| 31 | Newspaper Archive Racks | As per standards |
| 32 | Beanbags | Beanbag XL Size, outer covering to be Leatherette with choice of Colors to be specified with Micro-bead filling with a weight of more than 5 Kgs. |
| 33 | Furniture for browsing center: computer table and revolving chairs 55-60 chairs + 55-60 tables | As per the Standard specifications |
| 34 | Sofa C | seat foam: the seat should bemade of pu foam with density 32 ± 2 kg/cu.mtr having an additional top layer of j pu foam with density 28 ± 2 kg/cu. seat should beupholstered with fabric or leatherette. 2) back foam: the back should bemade of pu foam with density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette Understructure :under structure should bemade up of 1.2±0.1 cm. thick hot pressed plywoodocp-qlta-pl14-18 4. dia 4mm zigzag spring assembly should bemounted in understructure for support and additional cushioning purposeleg assembly: it should bea welded assembly made in stainless steel (grade ss 202) tube & plate. |
| 35 | Conference Table (Folding Tables for Multi-purpose hall) | Worktop: Made of 25mm Thick Pre-laminated twin board interior grade of approved shade conforming toIS:12823, and Edge banded with matching 2 mm thick PVC lipping. Modesty Panel: Made of 25mm Thick Pre-laminated twin board interior grade of approved shade conforming to IS:12823 and Edge banded with matching 2 mm thick PVC lipping 1200mm x 600 mm. Under-structure: Legs are made of 50mm x 30mm x 1.6mm thk M.S. electric resistance welding tube as per IS:7138 and 10 mm thick HR steel as per IS 2062 welded together and powder coated with min 45 micron thickness of epoxy polyester coating. Modesty holding Leg frame is made of made of 50mm x 30mm x 1.6mm thk M.S. electric resistance welding tube as per IS:7138 and 3mm thick HR steel as per IS 2062 welded together and powder coated with min 45 micron thickness of epoxy polyester coating. Cross member assembly for top is made of made of 50mm x 30mm x 1.6mm thk electric resistance welding tube as per IS:7138 and 3 mm thick HR steel as per IS 2062 welded together and are powder coated withmin 45 micron thickness of epoxy polyester coating Pull handle made of Ø16.0 x 1.2mm thk M.S. electric resistance welding tube as per IS:7138, powder coated with min 45 micron thickness of epoxy polyester coating. Housing bracket assembly is made of 3 mm thick HR steel as per IS 2062 welded together and is powder coated with min 45 micron thickness of epoxy polyester coating.Housing bracket carries mechanism for folding table made of 10mm thick HR steel as per IS 2062. Understructure is provided with Ø 65mm lockable Castors for ease of movement and can be locked when required at any position.The product must be either Greenguard or BifmaLeve or IAQ or Griha certified. |
| 36 | Chairs for Conference room (Revolving chair for folding tables) | The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyester fabric. The back size shall be 44cm W x 46cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the back spine structure involved in multi-dimensional recline motion. The adjustable armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled Polyamide. The powder coated tubular frame is cantilever type and made of dida 2.54cm x 0.3cm thik MS ERW tube. Shoes are made of glass filled POly amide and fixed to thw tubular frame. The overall dimensions of the chair shall be 48.5x 58.9cm x93.5cm. The seat height shall be 47.5cm. The product must be either Greenguard or BifmaLeve or IAQ or Griha certified. |
| 37 | Stationery/Fixed Chairs for Conference room | Fixed in floor, Mid Back Chair W X D = 76 cm X 76 cm UAholstery Material: Fabric |
