Public Works Department-PWD has published Tender For Infrastructure Development And Retrofitting Works Under Accessible India Campaign ( Aic ) In The State Of Arunachal Pradesh. Phase-I. Submission Date for this Tender is 22-10-2021. Infrastructure Work Tenders in Itanagar Arunachal Pradesh. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Sub-Work :- (1) Infrastructure Development and Retofitting works under AIC at Civil Secretriate Premises, Itanagar. |
| 2 | WALK WAYS FOR PEDESTRIAN & CAR PARKING RESERVATION: Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil androck), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 3 | Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade |
| 4 | Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (i) for grading- I Material |
| 5 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 6 | Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing ) |
| 7 | Centring and shuttering including strutting proping etc. and removal of form work for: a) Foundations and plinth |
| 8 | Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mmin floors on 25 mm thick bed mortar 1:3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: a) Light shades using white cement |
| 9 | Providing and installation of Tactile Tiles of suitable warning and guiding indicator blocks as per the Standard Factory manufactured Specification conforming to the requisite IS code of manufactuering on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: |
| 10 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories &stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waistslab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 11 | Supply and providing of brailled signage boards for disabled assessibility of standard acrylic vinyle material as per the direction of the Engineer in charge. |
| 12 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorisin g glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.) |
| 13 | Traffic Cone (Provision of red fluorescent with white reflective sleeve traffic cone made of low density polyethylene(LDPE) material with a square base of 390 x 390 x 35 mm and a height of 770 mm, 4 kg in weight, placed at 1.5 m interval, all as per BS 873) |
| 14 | Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/ bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. |
| 15 | Street Lighting (Providing and erecting street light mounted on a steel circular hollow pole of standard specifications for street lighting, 9 m high spaced 40 m apart,1.8 m over hang on both sides if fixed in the median and on one side if fixed on the footpath, fitted with sodium vapour lamp and fixed firmly in concrete foundation.) (ii) For fixing in Footpath |
| 16 | Cable Duct Across the Road (Providing and laying of are inforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cut sand toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997,bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC: 98 - 1997 and approved drawings.) (iii) Triple Row for three utility services |
| 17 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 18 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 19 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and switch, connection etc. as required. |
| 20 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 21 | MCCB, MCB & DB’S: Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incomming and outgoing circuits, duly prewiredwith suitable size FRLS PVC insulatedcopper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate,interconnections , power painted i/c earthing etc. as required.(But without MCB/ RCCB/ Isolator). (2 + 4) way/6way, Double door |
| 22 | Supplying and fixing30A, 440V, TPN industrial type, socket outlet with 4 pole and earth metal enclosed plug top alongwith 30A C series TPMCB, in sheet steel enclosure, on surface or in recessed with chained metal cover for the socket outlet and complete with connections, testing and commisioning etc as required. |
| 23 | Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors outgoing circuits, duly prew interconnections, powder painted including earthing etc. asired with suitable size FRLS PVCfor all incoming and insulated copper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate, required.(But without MCB/ RCCB/ Isolator). 4 way (4 + 12), Double door |
| 24 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole |
| 25 | (b) Single pole and neutral |
| 26 | Supplying and fixing following rating, Double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. : 40 amps |
| 27 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps |
| 28 | CABLE TRAYS: Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness |
| 29 | Providing and fixing M.V. danger notice plate of 200 mm X 150mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 30 | EARTHING: Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 31 | Earthing with G.I. earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charchol/coke and salt as required. |
| 32 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 33 | MV CABLE & LAYING: Supply of Alluminium conductor, PVC/XLPE insulated, armoured, overall PVC sheathed 1100 Volts Grade Power Cables Confirming to IS 1554 / 7098 ( Part - I ) 1988 with latest amendmentswith all accessories of Cable lug, pin etc of following sizes : 4 X 10 sq. Mm |
| 34 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. Mm |
| 35 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (Clamped with 1mm thick saddle) |
| 36 | MV CABLE JOINTING & END TERMINATION: Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 3½ X 240 sq. mm |
| 37 | (b) 3½ X 50 sq. mm |
| 38 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 39 | Supply, Installation, testing and Commissioning of Weather proof Lighting Fixtures and Accessories as per standard vendors specification ( All lighting fixttures provided with required no. of double compression Nickel plated brass cable glands and stopping plug) SITC of WP 60 Watt LED Glass Type Lighting fixture with toughened glass and mesh suitable for LED lamp with integral type control gear box as per the standard available with vendor. |
| 40 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 41 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. 150 mm dia |
| 42 | Printing new letter and figures of any shade (Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade) (i) Hindi ( Matrascommas andthelike notto bemeasuredandpaidforHalf letter shall be counted as half ) |
| 43 | (ii) English and Roman |
| 44 | Carving of Brailles in SS Pipe and other metal sheet for enabling Signs in Handrails and Hand Sign Boards for Divyanjans. |
| 45 | Supply, Installation, testing and Commissioning of Ornamental type out door garden type Bench (3 Seater Capacity) of suitable pattern and approved vendor manufacturer as per the direction of the engineer in charge fordimensional standard as per the accessibiity & space code parameters for Person with Disabilities. |
| 46 | RETROFITTING WORKS IN RAMPS, STAIRCASE, PASSAGE CORRIDORS , COUNTERS ETC.: Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete |
| 47 | Providing and fixing of Reflective Fluorescent anti skid PVC Strips in Steps & Corridors. |
| 48 | (Providing with SS Guiding Studs for affixing in existing flooring tiles/ Stone works as Guiding pattern block signs) Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 49 | (Providing with SS Warning Studs for affixing in existing flooring tiles/ Stone works as Guiding & Warning pattern block signs)Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 50 | Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) conforming to IS: 14587:1998 marked, with (one side decorative and other side balancing lamination and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brandwith necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete. 25 mm thick Providing and fixing 25 mm thick shutters for cup board etc. : Panelled or panelled & glazed shutters : |
| 51 | 9.16.1.2 Second class teak wood including iSi marked nickel plated bright finished M.S. piano hinges with necessary screw |
| 52 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour and shade 8.2.2.1 - Area of slab upto 0.50 sqm |
| 53 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete |
| 54 | Painting two or more coats (excluding priming coat) with superior ready mixedpaintfor woodwork of approved brandand manufacture in allshades on new work to give an even shade |
| 55 | RETROFITTING WORKS IN TOILET BLOCKS: Demolishing brick work in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 56 | Dismantling wood work of sectional area 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead. |
| 57 | Taking out doors, windows and clerestory windows shutters (steel or wood) including stacking within 50 m lead. a) Of area 3 Sq.m. and below |
| 58 | Dismantlingthe tilework infloors androofs laidincement includingstacking of materials within 50 m lead. a) For thickness of tiles 10 mm to 25 mm |
| 59 | Demolishing RCC work including stacking of steel bars and disposal of unserviceable materials within 50 metres lead. |
| 60 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth. |
| 61 | Extra for half brick masonry in super structure above plinth level and up to floor two level. |
| 62 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame |
| 63 | Providing and fixing to existing door frames.: 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge |
| 64 | Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete. a) 125 x 65 x 2.12 mm |
| 65 | Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete. a) 300 x 16 mm |
| 66 | Providing and fixing MS tower bolts (barrel type) with necessary screws etc complete. a) 250 x 10 mm |
| 67 | Providing and fixing MS handles with necessary screws etc complete. a) 125 mm |
| 68 | Providing and fixing MS Hooks and Eyes. a) 300 mm |
| 69 | Providing and fixing MS safety hasp and staple with necessary screws etc complete. a) 150 mm |
| 70 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 71 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 72 | 20 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 73 | Extra for plaster to ceiling above 5 m height from floor lavel for every additional height of one metre or part there-of. |
| 74 | Extra for providing and mixing water proofing materials in proportion recommended by the manufacturers. |
| 75 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 76 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : Two coats |
| 77 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.2-W.C. pan with ISI marked black solid plastic seat and lid |
| 78 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1-Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 79 | Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : 17.6.1- Single squatting plate with 5 litre P.V.C. automatic flushing cistern |
| 80 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a)White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 81 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Semi rigid pipe 17.28.1.1 - 32 mm dia |
| 82 | Providing and fixing 100 mm sand cast Iron grating for gully trap |
| 83 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.4 - Rectangular shape 1500x450 mm |
| 84 | Providing and fixing toilet paper holder : 17.34.1- C.P. brass |
| 85 | Providing and fixing soil, waste and vent pipes : 75 mm diameter : 17.35.2.1- Sand cast iron S&S pipe as per IS: 1729 |
| 86 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 17.36.1 - 75 mm dia pipe |
| 87 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 18.7.1 15 mm nominal outer dia Pipes |
| 88 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 18.50.1- 15 mm nominal bore |
| 89 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms |
| 90 | Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 18.84.1-15 mm nominal bore |
| 91 | Providing and fixing chest support grab for urinalof Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 92 | Providingfixing and installation offoldable grab bar near WC & wash basin etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 93 | Providingfixing and installation ofD"handles of cercular section etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 94 | Supply, Installation, Testing & Commissioning of Drinking Water fountain ( delivery output- 32 Litres per hour) with temperature adjustment system with Flexible bubbler guard having heavy guage Galvanised steel frame meeting the needs and as per the set conforming to IS standard of the Phusically challenged and the able-bodied. |
| 95 | Sub-Work:- (2) Infrastructure Development and Retofitting works under AIC at Arunachal Legislative Assembly Premises, Itanagar |
| 96 | WALK WAYS FOR PEDESTRIAN & CAR PARKING RESERVATION Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil androck), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 97 | Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade |
| 98 | Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) a) (i) for grading- I Material |
| 99 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 100 | Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing ) |
| 101 | Centring and shuttering including strutting proping etc. and removal of form work for: a) Foundations and plinth |
| 102 | Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mmin floors on 25 mm thick bed mortar 1:3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: a) Light shades using white cement |
| 103 | Providing and installation of Tactile Tiles of suitable warning and guiding indicator blocks as per the Standard Factory manufactured Specification conforming to the requisite IS code of manufactuering on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: |
| 104 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories &stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waistslab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 105 | Supply and providing of brailled signage boards for disabled assessibility of standard acrylic vinyle material as per the direction of the Engineer in charge. |
| 106 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorisin g glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.) |
| 107 | Traffic Cone (Provision of red fluorescent with white reflective sleeve traffic cone made of low density polyethylene(LDPE) material with a square base of 390 x 390 x 35 mm and a height of 770 mm, 4 kg in weight, placed at 1.5 m interval, all as per BS 873) |
| 108 | Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/ bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. |
| 109 | Street Lighting (Providing and erecting street light mounted on a steel circular hollow pole of standard specifications for street lighting, 9 m high spaced 40 m apart,1.8 m over hang on both sides if fixed in the median and on one side if fixed on the footpath, fitted with sodium vapour lamp and fixed firmly in concrete foundation.) (ii) For fixing in Footpath |
| 110 | Cable Duct Across the Road (Providing and laying of are inforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cut sand toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997,bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC: 98 - 1997 and approved drawings.) (iii) Triple Row for three utility services |
| 111 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 112 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 113 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and switch, connection etc. as required. |
| 114 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 115 | MCCB, MCB & DB’S Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incomming and outgoing circuits, duly prewiredwith suitable size FRLS PVC insulatedcopper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate,interconnections , power painted i/c earthing etc. as required.(But without MCB/ RCCB/ Isolator) (2 + 4) way/6way, Double door |
| 116 | Supplying and fixing30A, 440V, TPN industrial type, socket outlet with 4 pole and earth metal enclosed plug top alongwith 30A C series TPMCB, in sheet steel enclosure, on surface or in recessed with chained metal cover for the socket outlet and complete with connections, testing and commisioning etc as required. |
| 117 | Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors outgoing circuits, duly prew interconnections, powder painted including earthing etc. asired with suitable size FRLS PVCfor all incoming and insulated copper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate, required.(But without MCB/ RCCB/ Isolator). a) 4 way (4 + 12), Double door |
| 118 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. A) Single pole |
| 119 | b) Single pole and neutral |
| 120 | Supplying and fixing following rating, Double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. a) 40 amps |
| 121 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. a)40 amps |
| 122 | CABLE TRAYS Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. a)300 mm width X 50 mm depth X 1.6 mm thickness |
| 123 | Providing and fixing M.V. danger notice plate of 200 mm X 150mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 124 | EARTHING Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 125 | Earthing with G.I. earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charchol/coke and salt as required. |
| 126 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 127 | MV CABLE & LAYING Supply of Alluminium conductor, PVC/XLPE insulated, armoured, overall PVC sheathed 1100 Volts Grade Power Cables Confirming to IS 1554 / 7098 ( Part - I ) 1988 with latest amendmentswith all accessories of Cable lug, pin etc of following sizes : (a) 4 x 10 sq. Mm |
| 128 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required (a) Upto 35 sq. Mm |
| 129 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. A) Upto 35 sq. mm (Clamped with 1mm thick saddle) |
| 130 | MV CABLE JOINTING & END TERMINATION Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 3½ X 240 sq. mm |
| 131 | (b) 3½ X 50 sq. mm |
| 132 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 133 | Supply, Installation, testing and Commissioning of Weather proof Lighting Fixtures and Accessories as per standard vendors specification ( All lighting fixttures provided with required no. of double compression Nickel plated brass cable glands and stopping plug) a) SITC of WP 60 Watt LED Glass Type Lighting fixture with toughened glass and mesh suitable for LED lamp with integral type control gear box as per the standard available with vendor. |
| 134 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 135 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. A) 150 mm dia |
| 136 | Printing new letter and figures of any shade (Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade) a) (i) Hindi ( Matrascommas andthelike notto bemeasuredandpaidforHalf letter shall be counted as half ) |
| 137 | (ii) English and Roman |
| 138 | Carving of Brailles in SS Pipe and other metal sheet for enabling Signs in Handrails and Hand Sign Boards for Divyanjans. |
| 139 | Supply, Installation, testing and Commissioning of Ornamental type out door garden type Bench (3 Seater Capacity) of suitable pattern and approved vendor manufacturer as per the direction of the engineer in charge fordimensional standard as per the accessibiity & space code parameters for Person with Disabilities. |
| 140 | RETROFITTING WORKS IN RAMPS, STAIRCASE, PASSAGE CORRIDORS , COUNTERS ETC. Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete |
| 141 | Providing and fixing of Reflective Fluorescent anti skid PVC Strips in Steps & Corridors. |
| 142 | (Providing with SS Guiding Studs for affixing in existing flooring tiles/ Stone works as Guiding pattern block signs) Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 143 | (Providing with SS Warning Studs for affixing in existing flooring tiles/ Stone works as Guiding & Warning pattern block signs) Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 144 | Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) conforming to IS: 14587:1998 marked, with (one side decorative and other side balancing lamination and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brandwith necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete. a) 25 mm thick |
| 145 | Providing and fixing 25 mm thick shutters for cup board etc. : a) Panelled or panelled & glazed shutters : 9.16.1.2 Second class teak wood including iSi marked nickel plated bright finished M.S. piano hinges with necessary screw |
| 146 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels a) Granite of any colour and shade 8.2.2.1 - Area of slab upto 0.50 sqm |
| 147 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete |
| 148 | Painting two or more coats (excluding priming coat) with superior ready mixedpaintfor woodwork of approved brandand manufacture in allshades on new work to give an even shade |
| 149 | RETROFITTING WORKS IN TOILET BLOCKS Demolishing brick work in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 150 | Dismantling wood work of sectional area 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead. |
| 151 | Taking out doors, windows and clerestory windows shutters (steel or wood) including stacking within 50 m lead. a) Of area 3 Sq.m. and below |
| 152 | Dismantlingthe tilework infloors androofs laidincement includingstacking of materials within 50 m lead. a) For thickness of tiles 10 mm to 25 mm |
| 153 | Demolishing RCC work including stacking of steel bars and disposal of unserviceable materials within 50 metres lead. |
| 154 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth. |
| 155 | Extra for half brick masonry in super structure above plinth level and up to floor two level. |
| 156 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame |
| 157 | Providing and fixing to existing door frames. A)30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge |
| 158 | Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete. a) 125 x 65 x 2.12 mm |
| 159 | Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete. a) 300 x 16 mm |
| 160 | Providing and fixing MS tower bolts (barrel type) with necessary screws etc complete. a) 250 x 10 mm |
| 161 | Providing and fixing MS handles with necessary screws etc complete. a) 125 mm |
| 162 | Providing and fixing MS Hooks and Eyes. a) 300 mm |
| 163 | Providing and fixing MS safety hasp and staple with necessary screws etc complete. a) 150 mm |
| 164 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 165 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 166 | 20 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 167 | Extra for plaster to ceiling above 5 m height from floor lavel for every additional height of one metre or part there-of. |
| 168 | Extra for providing and mixing water proofing materials in proportion recommended by the manufacturers. |
| 169 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 170 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : a) Two coats |
| 171 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : a) 17.3.2-W.C. pan with ISI marked black solid plastic seat and lid |
| 172 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1-Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 173 | Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : a) 17.6.1- Single squatting plate with 5 litre P.V.C. automatic flushing cistern |
| 174 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a)White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 175 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete a) Semi rigid pipe 17.28.1.1 - 32 mm dia |
| 176 | Providing and fixing 100 mm sand cast Iron grating for gully trap |
| 177 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : a) 17.32.4 - Rectangular shape 1500x450 mm |
| 178 | Providing and fixing toilet paper holder : a) 17.34.1- C.P. brass |
| 179 | Providing and fixing soil, waste and vent pipes : a)75 mm diameter : 17.35.2.1- Sand cast iron S&S pipe as per IS: 1729 |
| 180 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : a) 17.36.1 - 75 mm dia pipe |
| 181 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. a) Internal work - Exposed on wall 18.7.1 15 mm nominal outer dia Pipes |
| 182 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. A)18.50.1- 15 mm nominal bore |
| 183 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms |
| 184 | Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. A) 18.84.1-15 mm nominal bore |
| 185 | Providing and fixing chest support grab for urinalof Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 186 | Providingfixing and installation offoldable grab bar near WC & wash basin etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 187 | Providingfixing and installation ofD"handles of cercular section etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 188 | Supply, Installation, Testing & Commissioning of Drinking Water fountain ( delivery output- 32 Litres per hour) with temperature adjustment system with Flexible bubbler guard having heavy guage Galvanised steel frame meeting the needs and as per the set conforming to IS standard of the Phusically challenged and the able-bodied. |
| 189 | Sub-Work :- (3) Construction & Retrofication works under AIC at Indira Gandhi Park, Itanagar |
| 190 | WALK WAYS FOR PEDESTRIAN & CAR PARKING RESERVATION Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil androck), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 191 | Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade |
| 192 | Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (i) for grading- I Material |
| 193 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 194 | Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing ) |
| 195 | Centring and shuttering including strutting proping etc. and removal of form work for: a) Foundations and plinth |
| 196 | b] Column, pillars, posts and struts etc. |
| 197 | c) Lintels, beams, girders, bressumers and cantilevers etc. |
| 198 | d) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas . |
| 199 | b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 200 | Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mmin floors on 25 mm thick bed mortar 1:3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: c) Dark shade using ordinary cement |
| 201 | Providing and installation of Tactile Tiles of suitable warning and guiding indicator blocks as per the Standard Factory manufactured Specification conforming to the requisite IS code of manufactuering on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: |
| 202 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories &stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waistslab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 203 | Supply and providing of brailled signage boards for disabled assessibility of standard acrylic vinyle material as per the direction of the Engineer in charge. |
| 204 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorisin g glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.) |
| 205 | Traffic Cone (Provision of red fluorescent with white reflective sleeve traffic cone made of low density polyethylene(LDPE) material with a square base of 390 x 390 x 35 mm and a height of 770 mm, 4 kg in weight, placed at 1.5 m interval, all as per BS 873) |
| 206 | Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/ bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. |
| 207 | Street Lighting (Providing and erecting street light mounted on a steel circular hollow pole of standard specifications for street lighting, 9 m high spaced 40 m apart,1.8 m over hang on both sides if fixed in the median and on one side if fixed on the footpath, fitted with sodium vapour lamp and fixed firmly in concrete foundation.) (ii) For fixing in Footpath |
| 208 | Cable Duct Across the Road (Providing and laying of are inforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cut sand toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997,bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC: 98 - 1997 and approved drawings.) (iii) Triple Row for three utility services |
| 209 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 210 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 211 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and switch, connection etc. as required. |
| 212 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 213 | MCCB, MCB & DB’S Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incomming and outgoing circuits, duly prewiredwith suitable size FRLS PVC insulatedcopper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate,interconnections , power painted i/c earthing etc. as required.(But without MCB/ RCCB/ Isolator) (2 + 4) way/6way, Double door |
| 214 | Supplying and fixing30A, 440V, TPN industrial type, socket outlet with 4 pole and earth metal enclosed plug top alongwith 30A C series TPMCB, in sheet steel enclosure, on surface or in recessed with chained metal cover for the socket outlet and complete with connections, testing and commisioning etc as required. |
| 215 | Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors outgoing circuits, duly prew interconnections, powder painted including earthing etc. asired with suitable size FRLS PVCfor all incoming and insulated copper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate, required.(But without MCB/ RCCB/ Isolator) 4 way (4 + 12), Double door |
| 216 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. a) Single pole |
| 217 | b) Single pole and neutral |
| 218 | Supplying and fixing following rating, Double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. A)40 amps |
| 219 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. A) 40 amps |
| 220 | CABLE TRAYS Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. a) 300 mm width X 50 mm depth X 1.6 mm thickness |
| 221 | Providing and fixing M.V. danger notice plate of 200 mm X 150mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 222 | EARTHING Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 223 | Earthing with G.I. earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charchol/coke and salt as required. |
| 224 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 225 | MV CABLE & LAYING Supply of Alluminium conductor, PVC/XLPE insulated, armoured, overall PVC sheathed 1100 Volts Grade Power Cables Confirming to IS 1554 / 7098 ( Part - I ) 1988 with latest amendmentswith all accessories of Cable lug, pin etc of following sizes : a)4 X 10 sq. Mm |
| 226 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. A) Upto 35 sq. Mm |
| 227 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. a)Upto 35 sq. mm (Clamped with 1mm thick saddle) |
| 228 | MV CABLE JOINTING & END TERMINATION Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. A) 3½ X 240 sq. mm |
| 229 | 3½ X 50 sq. mm |
| 230 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 231 | Supply, Installation, testing and Commissioning of Weather proof Lighting Fixtures and Accessories as per standard vendors specification ( All lighting fixttures provided with required no. of double compression Nickel plated brass cable glands and stopping plug) SITC of WP 60 Watt LED Glass Type Lighting fixture with toughened glass and mesh suitable for LED lamp with integral type control gear box as per the standard available with vendor. |
| 232 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 233 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. A) 150 mm dia |
| 234 | Printing new letter and figures of any shade (Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade). (i) Hindi ( Matrascommas andthelike notto bemeasuredandpaidforHalf letter shall be counted as half ) |
| 235 | (ii) English and Roman |
| 236 | Carving of Brailles in SS Pipe and other metal sheet for enabling Signs in Handrails and Hand Sign Boards for Divyanjans. |
| 237 | Supply, Installation, testing and Commissioning of Ornamental type out door garden type Bench (3 Seater Capacity) of suitable pattern and approved vendor manufacturer as per the direction of the engineer in charge fordimensional standard as per the accessibiity & space code parameters for Person with Disabilities. |
| 238 | RETROFITTING WORKS IN RAMPS, STAIRCASE, PASSAGE CORRIDORS , COUNTERS ETC Painting two or more coats (excluding priming coat) with superior ready mixedpaintfor woodwork of approved brandand manufacture in allshades on new work to give an even shade |
| 239 | RETROFITTING WORKS IN TOILET BLOCKS Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth. |
| 240 | Extra for half brick masonry in super structure above plinth level and up to floor two level. |
| 241 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame |
| 242 | Providing and fixing to existing door frames. A) 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge |
| 243 | Providing and fixing chest support grab for urinalof Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 244 | Providingfixing and installation offoldable grab bar near WC & wash basin etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 245 | Providingfixing and installation ofD"handles of cercular section etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 246 | Supply, Installation, Testing & Commissioning of Drinking Water fountain ( delivery output- 32 Litres per hour) with temperature adjustment system with Flexible bubbler guard having heavy guage Galvanised steel frame meeting the needs and as per the set conforming to IS standard of the Phusically challenged and the able-bodied. |
| 247 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 248 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 249 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:a) Foundations and plinth |
| 250 | Reinforced concrete work in foundations, footings, bases of columns etc. And mass concrete excluding cost of centring, shuttering and reinforcement in : a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 251 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement./a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 252 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 253 | Reinforcement of RCC work including bending, binding and placing in position complete. A) Cold Twisted bar |
| 254 | 25 mm thick cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) finished with a floating coat of neat cement |
| 255 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth |
| 256 | Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand). |
| 257 | Extra for brick work with best available local bricks in superstructure above plinth level up to floor two level. |
| 258 | 15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall. |
| 259 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 260 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: a)13.47.1 - New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 261 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. a) 13.83.2 - Two coats |
| 262 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 263 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 264 | Providing and fixing 20mm x20mm (or simillar size) glass mosaic tiles of texture series ofItalia or equivallent of approved colour and texture on wall facia etc. at any height including all materials and labours complete |
| 265 | Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position. |
| 266 | Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws./a) 38mm thick best available local wood class - B I |
| 267 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete |
| 268 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 269 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete .a)250 x 16 mm |
| 270 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. a)200 x 10 mm |
| 271 | 150 x 10 mm |
| 272 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : a)100 mm |
| 273 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparentf hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. |
| 274 | Steel work riveted or bolted in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint. b) In Tees, Angles, Flats and Channels |
| 275 | Providing and fixing in position collapsible steel shutters with vertical channels 20 mm x 10 mm x 2 mm and braced with flat iron diagonals 20 mm x 5 mm size with top and bottom rails of T iron 40 mm x 40 mm x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint. |
| 276 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 277 | Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc. |
| 278 | Applying priming coat consisting of a mixture of red lead, white lead and double boiled linseed oil in the ratio of 0.7 Kg : 0.7 Kg : 1 Litre on wood work complete. |
| 279 | Providing and fixing white vitreous china flat back half stall urinal of size 580X380X350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS: 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required: a)Supply, istallation, testing & Commissioning Range of two half stall urinals with 10 litre P.V.C. automatic flushing cistern suited for Acessibility standard for divyangans. |
| 280 | Supply, istallation, testing & Commissioning of Napkin Disposal and Toilet Tissue Dispenser in complete set suited for Acessibility standard for divyangans. |
| 281 | Providing and fixing white vitreous china wash basin with C.I. brackets, 15 mm C.P. brass piller taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White vitreous China Wash basin size 750X450mm with a pair of 15 mm C.P. brass pillar taps a) Supply, istallation, testing & Commissioning of Counter Top Sink (1.2 X 0.45 m) in complete set suited for Acessibility standard for divyangans. |
| 282 | Supply, istallation, testing & Commissioning of Standard Automatic P.T Soap liquid dispenser in complete set suited for Acessibility standard for divyangans. |
| 283 | Providing and fixing white vitreous china pedestal type water closet (european Type W.C. pan) with seat and lid, 10 litre low level pvc flushing cistern,including flush pipe,with manualy controlled device within brackets handle lever,conforming to IS:7231,with all fittings & fixtures complete, including cutting and making good the walls & floors wherever required. a) W.C. pan with ISI marked white solid plastic seat and lidin complete set suited for Acessibility standard for divyangans. |
| 284 | Supply, istallation, testing & Commissioning of Wall Mounted Lavatory and Soap Dispenser in complete set suited for Acessibility standard for divyangans. |
| 285 | Providing and fixing white vitreous china wash basin with C.I. brackets, 15 mm C.P. brass piller taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : a) Flat back wash basin size 550 x 400 mm with single 15 mm C.P. brass piller taps |
| 286 | Providing and fixing 600 X 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete . |
| 287 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work 15 mm dia nominal bore |
| 288 | Providing and fixing brass bib cock of approved quality/15 mm nominal bore/15 mm nominal bore |
| 289 | Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg). |
| 290 | Providing laying and jointing glazed stone ware pipe grade "A" with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. Complete/150 mm dia SW pipes |
| 291 | Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design /150 mm dia SW pipes |
| 292 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 12.41.1 75 mm diameter |
| 293 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : a) 21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 294 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): a) 21.3.1 - With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm) |
| 295 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. A) 21.8.1-Upto 5mm depth and 5 mm width |
| 296 | Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. A) 21.12.2 Powder coated minimum thickness 50 micron aluminium tubular handle bar |
| 297 | Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 298 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). |
| 299 | 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 300 | Neat cement punning. |
| 301 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 302 | Construction of soak pit 1.2 x 1.1 x 1.2 m filled with brick bats including SW drain pipe 100 mm dia and 1.20 m long complete as per standard design. |
| 303 | DESIGNATED DIVYANGJAN PARK Clearing and Grubbing Road Land .(Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness.) (ii) By Mechanical Means (A) In area of light jungle |
| 304 | Excavation in Soil with Dozer with lead upto 100 metres ( Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead 50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.) |
| 305 | Stripping, storing and re-laying top soil from borrow areas in agriculture fields. (Stripping of top soil from borrow areas located in agriculture fields, storing at a suitable place, spreading and re-laying after taking the borrow earth to maintain fertility of the agricultural field, finishing it to the required levels and satisfaction of the farmer.) |
| 306 | Surface Drains in Soil (Construction of unlined surface drains of average cross sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions to the requirement of clause 301 and 309. Excavated material to be used in embankment within a lead of50 metres (average lead 25 metres)) A Mechanical means |
| 307 | Extra for making chequeres of approved pattern on cement concrete floors, landing and pavements etc |
| 308 | Brick edging 7.50 cm wide and 12.50 cm deep to plinth protection with 2nd class bricks including grouting with cement mortar 1 : 4 (1 cement : 4 fine sand). |
| 309 | Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 :6 (1 cement : 3 sand : 6 hard graded stone chips or aggrigate 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete |
| 310 | Providing laying and jointing glazed stone ware pipe grade "A" with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. c) 200 mm dia SW pipes |
| 311 | HORTICULTURE a) Planting Flowering Plants and Shrubs in Central Verge |
| 312 | a) Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart) |
| 313 | Turfing Lawns with Fine Grassing including Ploughing, Dressing (Turfing lawns with fine grassing including ploughing, dressing including breaking of clods, removal of rubbish, dressing and supplying doobs grass roots at 10 cm apart, including supplying and spreading of farm yard manure at rate of0.6 cum per 100 sqm) |
| 314 | Maintenance of Lawns with Fine Grassing for the First Year |
| 315 | Planting of Trees and their Maintenance for one Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year) |
| 316 | Renovation Lawns including, Weeding, Forking the Ground, Top Dressing with Forked Soil (Renovation lawns including, weeding, forking the ground, top dressing with forked soil, watering and maintenance the lawns, for 30 days or more, till the grass forms a thick lawn, free from weeds, and fit for moving and disposal of rubbish as directed, including supplying good earth, if needed but excluding the cost of well decayed farm yard manure) |
| 317 | Supply at Site Well Decayed Farm Yard Manure (Supply at site of work well decayed farm yard manure, from any available source, approved by the engineer in charge including screening and stacking) |
| 318 | Edging with 2nd class Bricks, laid dry lengthwise (Edging with 2nd class bricks, laid dry lengthwise, including excavation, refilling, consolidation, with a hand packing and spreading nearly surplus earth within a lead of 50 metres) |
| 319 | Tree Guard with MS Iron (Providing and fixing MS iron tree guard 60 cm dia and 2 metre high above ground level formed of 4 Nos (25 x 6 mm) and 8 Nos (25 x 3 mm) vertical MS riveted to 3 Nos (25 x 6 mm) iron rings in two halves, bolted together with 8 mm dia and 30 mm long bolts including painting two coats with paint of approved brand over a coat of priming, complete in all respects.) |
| 320 | RE-CREATIONAL EQUIPMENTS Supply Installation Testing and Commissioning of Outdoor fitness equipment- Air Walker elliptical training equipment with pedals travelling in a smooth and arched path ( Conforming Item Code- MF-001 Make Mega Fitness or equivalent; Dimension- 1100X600X1420 MM). |
| 321 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Air Swing training equipment with pedals and fixed handle (Conforming Item Code- MF-002 Make Mega Fitness or equivalent; Dimension- 1320X850X1250 MM) |
| 322 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Push Chairs of heavy guaged steel, self-weighted machine built to support a vigorous workouts for upto two people. (Conforming Item Code- MF-003 Make Mega Fitness or equivalent; Dimension- 2090X650X1810 MM) |
| 323 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Pull Chairs of heavy guaged steel, self-weighted machine built to support a vigorous workouts for upto two people. (Conforming Item Code- MF-004 Make Mega Fitness or equivalent; Dimension- 2010X990X2010 MM) |
| 324 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Elliptical Cross Trainer of heavy guaged steel. (Conforming Item Code- MF-005 Make Mega Fitness or equivalent; Dimension- 1350X500X1500 MM) |
| 325 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Arm and Paddle Bike. (Conforming Item Code- MF-006 Make Mega Fitness or equivalent; Dimension- 1187X488X1137 MM) |
| 326 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Double Skiing Machine exercise station. (Conforming Item Code- MF-007 Make Mega Fitness or equivalent; Dimension- 1350X665X1660 MM) |
| 327 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Single Rowing Machine exercise station with fixed seat sculling action. (Conforming Item Code- MF-008 Make Mega Fitness or equivalent; Dimension- 1300X970X1350 MM) |
| 328 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Triple Waist Twister equipment station comprising of three rotating pods. (Conforming Item Code- MF-010 Make Mega Fitness or equivalent; Dimension- 1450X1540X1380 MM) |
| 329 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Sit up Board equipment. (Conforming Item Code- MF-012 Make Mega Fitness or equivalent; Dimension- 1400X640X600 MM) |
| 330 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Double Arm Wheel equipment of height adjusted as per the direction of the Engineer-in-charge. (Conforming Item Code- MF-013 Make Mega Fitness or equivalent; Dimension- 900X850X1890 MM) |
| 331 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Push Up and Dip Station equipment of height adjusted as per the direction of the Engineer-in-charge. (Conforming Item Code- MF-014 Make Mega Fitness or equivalent; Dimension- 1600X625X1850 MM) |
| 332 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Parallel Barscum Chin Up bars equipment of height adjusted as per the direction of the Engineer-in-charge. (Conforming Item Code- MF-015 Make Mega Fitness or equivalent; Dimension- 900X1800X900 MM) |
| 333 | Supply Installation Testing and Commissioning of Outdoor fitness equipment- Monkey Bars heavy-duty fitness equipment with height adjusted as per the direction of the Engineer-in-charge. (Conforming Item Code- MF-016 Make Mega Fitness or equivalent; Dimension- 2400X760X2200 MM) |
| 334 | Reinforced cement concrete in walls (any thickness) including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in : a) M20 (1 cement : 1.5 corase sand : 3 stone aggregate 20 mm nominal size) |
| 335 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. a) 11.56.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 336 | Extra for pre finished nosing to treads of steps of marble stone. |
| 337 | Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade. |
| 338 | Providing and fixing T-iron frames for doors, windows and ventilators of MS Tee sections joints mitred and welded with 15 x 3 mm legs, 10 cm long embedded in cement concrete block 15 cm x 10 cm x 10 cm size of 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or bolt and nuts as required, including fixing of necessary butt hinges and screws and applying a priming coat of approved primer. |
| 339 | Providing and laying up to floor two level cement 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size) including centring shuttering in : (d) Mouldings as in cornices, windows sills etc. exceeding 15 cm in girth. |
| 340 | Stone masonry work in cement mortar 1:3 in foundation complete as per drawing and Technical Specification a) S quare Rubble Coursed rubble masonry( first sort ) |
| 341 | Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specifications |
| 342 | Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification A) Granular material |
| 343 | Sub-Work :- (4) Infrastructure Development and Retofitting works under AIC at Science Centre, Itanagar |
| 344 | WALK WAYS FOR PEDESTRIAN & CAR PARKING RESERVATION: Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil androck), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 345 | Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade |
| 346 | Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (i) for grading- I Material |
| 347 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 348 | Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing ) |
| 349 | Centring and shuttering including strutting proping etc. and removal of form work for: a) Foundations and plinth |
| 350 | Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mmin floors on 25 mm thick bed mortar 1:3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: a) Light shades using white cement |
| 351 | Providing and installation of Tactile Tiles of suitable warning and guiding indicator blocks as per the Standard Factory manufactured Specification conforming to the requisite IS code of manufactuering on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: |
| 352 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories &stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waistslab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 353 | Supply and providing of brailled signage boards for disabled assessibility of standard acrylic vinyle material as per the direction of the Engineer in charge. |
| 354 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorisin g glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.) |
| 355 | Traffic Cone (Provision of red fluorescent with white reflective sleeve traffic cone made of low density polyethylene(LDPE) material with a square base of 390 x 390 x 35 mm and a height of 770 mm, 4 kg in weight, placed at 1.5 m interval, all as per BS 873) |
| 356 | Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/ bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. |
| 357 | Street Lighting (Providing and erecting street light mounted on a steel circular hollow pole of standard specifications for street lighting, 9 m high spaced 40 m apart,1.8 m over hang on both sides if fixed in the median and on one side if fixed on the footpath, fitted with sodium vapour lamp and fixed firmly in concrete foundation.) (ii) For fixing in Footpath |
| 358 | Cable Duct Across the Road (Providing and laying of are inforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cut sand toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997,bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC: 98 - 1997 and approved drawings.) (iii) Triple Row for three utility services |
| 359 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 360 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 361 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and switch, connection etc. as required. |
| 362 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 363 | MCCB, MCB & DB’S Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incomming and outgoing circuits, duly prewiredwith suitable size FRLS PVC insulatedcopper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate,interconnections , power painted i/c earthing etc. as required.(But without MCB/ RCCB/ Isolator) (2 + 4) way/6way, Double door |
| 364 | Supplying and fixing30A, 440V, TPN industrial type, socket outlet with 4 pole and earth metal enclosed plug top alongwith 30A C series TPMCB, in sheet steel enclosure, on surface or in recessed with chained metal cover for the socket outlet and complete with connections, testing and commisioning etc as required. |
| 365 | Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors outgoing circuits, duly prew interconnections, powder painted including earthing etc. asired with suitable size FRLS PVCfor all incoming and insulated copper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate, required.(But without MCB/ RCCB/ Isolator). |
| 366 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole |
| 367 | (b) Single pole and neutral |
| 368 | Supplying and fixing following rating, Double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps |
| 369 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps |
| 370 | CABLE TRAYS: Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness |
| 371 | Providing and fixing M.V. danger notice plate of 200 mm X 150mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 372 | EARTHING: Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 373 | Earthing with G.I. earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charchol/coke and salt as required. |
| 374 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 375 | MV CABLE & LAYING: Supply of Alluminium conductor, PVC/XLPE insulated, armoured, overall PVC sheathed 1100 Volts Grade Power Cables Confirming to IS 1554 / 7098 ( Part - I ) 1988 with latest amendmentswith all accessories of Cable lug, pin etc of following sizes : 4 X 10 sq. Mm |
| 376 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. Mm |
| 377 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (Clamped with 1mm thick saddle) MV CABLE JOINTING & END TERMINATION |
| 378 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 3½ X 240 sq. mm |
| 379 | (b) 3½ X 50 sq. mm |
| 380 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 381 | Supply, Installation, testing and Commissioning of Weather proof Lighting Fixtures and Accessories as per standard vendors specification ( All lighting fixttures provided with required no. of double compression Nickel plated brass cable glands and stopping plug) SITC of WP 60 Watt LED Glass Type Lighting fixture with toughened glass and mesh suitable for LED lamp with integral type control gear box as per the standard available with vendor. |
| 382 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 383 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required 150 mm dia |
| 384 | Printing new letter and figures of any shade (Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade) (i) Hindi ( Matrascommas andthelike notto bemeasuredandpaidforHalf letter shall be counted as half ) |
| 385 | (ii) English and Roman |
| 386 | Carving of Brailles in SS Pipe and other metal sheet for enabling Signs in Handrails and Hand Sign Boards for Divyanjans. |
| 387 | Supply, Installation, testing and Commissioning of Ornamental type out door garden type Bench (3 Seater Capacity) of suitable pattern and approved vendor manufacturer as per the direction of the engineer in charge fordimensional standard as per the accessibiity & space code parameters for Person with Disabilities. |
| 388 | RETROFITTING WORKS IN RAMPS, STAIRCASE, PASSAGE CORRIDORS , COUNTERS ETC.: Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete |
| 389 | Providing and fixing of Reflective Fluorescent anti skid PVC Strips in Steps & Corridors. |
| 390 | (Providing with SS Guiding Studs for affixing in existing flooring tiles/ Stone works as Guiding pattern block signs)Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 391 | (Providing with SS Warning Studs for affixing in existing flooring tiles/ Stone works as Guiding & Warning pattern block signs) Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 392 | Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) conforming to IS: 14587:1998 marked, with (one side decorative and other side balancing lamination and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brandwith necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete. 25 mm thick |
| 393 | Providing and fixing 25 mm thick shutters for cup board etc. : Panelled or panelled & glazed shutters : 9.16.1.2 Second class teak wood including iSi marked nickel plated bright finished M.S. piano hinges with necessary screw |
| 394 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour and shade 8.2.2.1 - Area of slab upto 0.50 sqm |
| 395 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete |
| 396 | Painting two or more coats (excluding priming coat) with superior ready mixedpaintfor woodwork of approved brandand manufacture in allshades on new work to give an even shade |
| 397 | RETROFITTING WORKS IN TOILET BLOCKS: Demolishing brick work in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 398 | Dismantling wood work of sectional area 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead. |
| 399 | Taking out doors, windows and clerestory windows shutters (steel or wood) including stacking within 50 m lead. a) Of area 3 Sq.m. and below |
| 400 | Dismantlingthe tilework infloors androofs laidincement includingstacking of materials within 50 m lead. a) For thickness of tiles 10 mm to 25 mm |
| 401 | Demolishing RCC work including stacking of steel bars and disposal of unserviceable materials within 50 metres lead. |
| 402 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth. |
| 403 | Extra for half brick masonry in super structure above plinth level and up to floor two level. |
| 404 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame |
| 405 | Providing and fixing to existing door frames.: 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge |
| 406 | Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete. a) 125 x 65 x 2.12 mm |
| 407 | Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete. a) 300 x 16 mm |
| 408 | Providing and fixing MS tower bolts (barrel type) with necessary screws etc complete. a) 250 x 10 mm |
| 409 | Providing and fixing MS handles with necessary screws etc complete. a) 125 mm |
| 410 | Providing and fixing MS Hooks and Eyes. a) 300 mm |
| 411 | Providing and fixing MS safety hasp and staple with necessary screws etc complete. a) 150 mm |
| 412 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 413 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 414 | 20 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 415 | Extra for plaster to ceiling above 5 m height from floor lavel for every additional height of one metre or part there-of. |
| 416 | Extra for providing and mixing water proofing materials in proportion recommended by the manufacturers. |
| 417 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 418 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : Two coats |
| 419 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.2-W.C. pan with ISI marked black solid plastic seat and lid |
| 420 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1-Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 421 | Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : 17.6.1- Single squatting plate with 5 litre P.V.C. automatic flushing cistern |
| 422 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a)White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 423 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Semi rigid pipe 17.28.1.1 - 32 mm dia |
| 424 | Providing and fixing 100 mm sand cast Iron grating for gully trap |
| 425 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.4 - Rectangular shape 1500x450 mm |
| 426 | Providing and fixing toilet paper holder : 17.34.1- C.P. brass |
| 427 | Providing and fixing soil, waste and vent pipes : 75 mm diameter 17.35.2.1- Sand cast iron S&S pipe as per IS: 1729 |
| 428 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 17.36.1 - 75 mm dia pipe |
| 429 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 18.7.1 15 mm nominal outer dia Pipes |
| 430 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 18.50.1- 15 mm nominal bore |
| 431 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms |
| 432 | Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 18.84.1-15 mm nominal bore |
| 433 | Providing and fixing chest support grab for urinalof Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 434 | Providingfixing and installation offoldable grab bar near WC & wash basin etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 435 | Providingfixing and installation ofD"handles of cercular section etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 436 | Supply, Installation, Testing & Commissioning of Drinking Water fountain ( delivery output- 32 Litres per hour) with temperature adjustment system with Flexible bubbler guard having heavy guage Galvanised steel frame meeting the needs and as per the set conforming to IS standard of the Phusically challenged and the able-bodied. |
| 437 | Sub-Work :- (5) Infrastructure Development and Retofitting works under AIC at Directorate of Tourism, Itanagar |
| 438 | WALK WAYS FOR PEDESTRIAN & CAR PARKING RESERVATION Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil androck), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 439 | Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade |
| 440 | Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (i) for grading- I Material |
| 441 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 442 | Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing ) |
| 443 | Centring and shuttering including strutting proping etc. and removal of form work for: a) Foundations and plinth |
| 444 | Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mmin floors on 25 mm thick bed mortar 1:3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: a) Light shades using white cement |
| 445 | Providing and installation of Tactile Tiles of suitable warning and guiding indicator blocks as per the Standard Factory manufactured Specification conforming to the requisite IS code of manufactuering on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: |
| 446 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories &stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waistslab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 447 | Supply and providing of brailled signage boards for disabled assessibility of standard acrylic vinyle material as per the direction of the Engineer in charge. |
| 448 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorisin g glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.) |
| 449 | Traffic Cone (Provision of red fluorescent with white reflective sleeve traffic cone made of low density polyethylene(LDPE) material with a square base of 390 x 390 x 35 mm and a height of 770 mm, 4 kg in weight, placed at 1.5 m interval, all as per BS 873) |
| 450 | Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/ bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. |
| 451 | Street Lighting (Providing and erecting street light mounted on a steel circular hollow pole of standard specifications for street lighting, 9 m high spaced 40 m apart,1.8 m over hang on both sides if fixed in the median and on one side if fixed on the footpath, fitted with sodium vapour lamp and fixed firmly in concrete foundation.) (ii) For fixing in Footpath |
| 452 | Cable Duct Across the Road (Providing and laying of are inforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cut sand toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997,bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC: 98 - 1997 and approved drawings.) (iii) Triple Row for three utility services |
| 453 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 454 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 455 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and switch, connection etc. as required. |
| 456 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 457 | MCCB, MCB & DB’S29-09-2021 Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incomming and outgoing circuits, duly prewiredwith suitable size FRLS PVC insulatedcopper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate,interconnections , power painted i/c earthing etc. as required.(But without MCB/ RCCB/ Isolator) (2 + 4) way/6way, Double door |
| 458 | Supplying and fixing30A, 440V, TPN industrial type, socket outlet with 4 pole and earth metal enclosed plug top alongwith 30A C series TPMCB, in sheet steel enclosure, on surface or in recessed with chained metal cover for the socket outlet and complete with connections, testing and commisioning etc as required. |
| 459 | Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors outgoing circuits, duly prew interconnections, powder painted including earthing etc. asired with suitable size FRLS PVCfor all incoming and insulated copper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate, required.(But without MCB/ RCCB/ Isolator). 4 way (4 + 12), Double door |
| 460 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 461 | Single pole and neutral |
| 462 | Supplying and fixing following rating, Double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps |
| 463 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps |
| 464 | CABLE TRAYS: Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness |
| 465 | Providing and fixing M.V. danger notice plate of 200 mm X 150mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 466 | EARTHING: Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 467 | Earthing with G.I. earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charchol/coke and salt as required. |
| 468 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 469 | MV CABLE & LAYING: Supply of Alluminium conductor, PVC/XLPE insulated, armoured, overall PVC sheathed 1100 Volts Grade Power Cables Confirming to IS 1554 / 7098 ( Part - I ) 1988 with latest amendmentswith all accessories of Cable lug, pin etc of following sizes : 4 X 10 sq. Mm |
| 470 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. Mm |
| 471 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (Clamped with 1mm thick saddle) |
| 472 | MV CABLE JOINTING & END TERMINATION: Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a)3½ X 240 sq. mm |
| 473 | (b) 3½ X 50 sq. mm |
| 474 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 475 | Supply, Installation, testing and Commissioning of Weather proof Lighting Fixtures and Accessories as per standard vendors specification ( All lighting fixttures provided with required no. of double compression Nickel plated brass cable glands and stopping plug) SITC of WP 60 Watt LED Glass Type Lighting fixture with toughened glass and mesh suitable for LED lamp with integral type control gear box as per the standard available with vendor. |
| 476 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 477 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. 150 mm dia |
| 478 | Printing new letter and figures of any shade (Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade) (i) Hindi ( Matrascommas andthelike notto bemeasuredandpaidforHalf letter shall be counted as half ) |
| 479 | (ii) English and Roman |
| 480 | Carving of Brailles in SS Pipe and other metal sheet for enabling Signs in Handrails and Hand Sign Boards for Divyanjans. |
| 481 | RETROFITTING WORKS IN RAMPS, STAIRCASE, PASSAGE CORRIDORS , COUNTERS ETC.: Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete |
| 482 | Providing and fixing of Reflective Fluorescent anti skid PVC Strips in Steps & Corridors. |
| 483 | (Providing with SS Guiding Studs for affixing in existing flooring tiles/ Stone works as Guiding pattern block signs)Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 484 | (Providing with SS Warning Studs for affixing in existing flooring tiles/ Stone works as Guiding & Warning pattern block signs) Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 485 | Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) conforming to IS: 14587:1998 marked, with (one side decorative and other side balancing lamination and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brandwith necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete. 25 mm thick |
| 486 | Providing and fixing 25 mm thick shutters for cup board etc. : Panelled or panelled & glazed shutters : 9.16.1.2 Second class teak wood including iSi marked nickel plated bright finished M.S. piano hinges with necessary screw |
| 487 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade 8.2.2.1 - Area of slab upto 0.50 sqm |
| 488 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete |
| 489 | Painting two or more coats (excluding priming coat) with superior ready mixedpaintfor woodwork of approved brandand manufacture in allshades on new work to give an even shade |
| 490 | RETROFITTING WORKS IN TOILET BLOCKS: Demolishing brick work in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 491 | Dismantling wood work of sectional area 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead. |
| 492 | Taking out doors, windows and clerestory windows shutters (steel or wood) including stacking within 50 m lead. a) Of area 3 Sq.m. and below |
| 493 | Dismantlingthe tilework infloors androofs laidincement includingstacking of materials within 50 m lead. a) For thickness of tiles 10 mm to 25 mm |
| 494 | Demolishing RCC work including stacking of steel bars and disposal of unserviceable materials within 50 metres lead. |
| 495 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth. |
| 496 | Extra for half brick masonry in super structure above plinth level and up to floor two level. |
| 497 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. Providing and fixing to existing door frames. |
| 498 | 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge |
| 499 | Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete. a) 125 x 65 x 2.12 mm |
| 500 | Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete. a) 300 x 16 mm |
| 501 | Providing and fixing MS tower bolts (barrel type) with necessary screws etc complete. a) 250 x 10 mm |
| 502 | Providing and fixing MS handles with necessary screws etc complete. a) 125 mm |
| 503 | Providing and fixing MS Hooks and Eyes. a) 300 mm |
| 504 | Providing and fixing MS safety hasp and staple with necessary screws etc complete. a) 150 mm |
| 505 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 506 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 507 | 20 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 508 | Extra for plaster to ceiling above 5 m height from floor lavel for every additional height of one metre or part there-of. |
| 509 | Extra for providing and mixing water proofing materials in proportion recommended by the manufacturers. |
| 510 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 511 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : Two coats |
| 512 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.2-W.C. pan with ISI marked black solid plastic seat and lid |
| 513 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1-Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 514 | Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : 17.6.1- Single squatting plate with 5 litre P.V.C. automatic flushing cistern |
| 515 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a)White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 516 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 17.28.1.1 - 32 mm dia |
| 517 | Providing and fixing 100 mm sand cast Iron grating for gully trap |
| 518 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.4 - Rectangular shape 1500x450 mm |
| 519 | Providing and fixing toilet paper holder : 17.34.1- C.P. brass |
| 520 | Providing and fixing soil, waste and vent pipes : 75 mm diameter 17.35.2.1- Sand cast iron S&S pipe as per IS: 1729 |
| 521 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 17.36.1 - 75 mm dia pipe |
| 522 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 18.7.1 15 mm nominal outer dia Pipes |
| 523 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 18.50.1- 15 mm nominal bore |
| 524 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms |
| 525 | Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 18.84.1-15 mm nominal bore |
| 526 | Providing and fixing chest support grab for urinalof Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 527 | Providingfixing and installation offoldable grab bar near WC & wash basin etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 528 | Providingfixing and installation ofD"handles of cercular section etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 529 | Supply, Installation, Testing & Commissioning of Drinking Water fountain ( delivery output- 32 Litres per hour) with temperature adjustment system with Flexible bubbler guard having heavy guage Galvanised steel frame meeting the needs and as per the set conforming to IS standard of the Phusically challenged and the able-bodied. |
| 530 | Provisioning for Design, Supply, Installation, Testing & Commissioning of Disability Hydraulic Platform lift with toughened Glass enclosureof mechanical device inclusive of all control Panel chamber works for Lifting people up and down stairs mounted and powered trail channel as per the Standard Operation Procedure of the manufacturer and GAD/QAP approval from the engineer in charge with features of joystick remote operated hand held in action and swivel seat comfort arrangement, also built in with 6 safety cut out sensors to detect possible obstructions & objects in elevation operation with net total carrying capacity of single unit to the maximum of 300 kgand speed @ 0-100 mm per Sec. Total rail flight till G+3 (4 Stop Opening) building height in total.(As per the direction of the Engineer-in-charge) |
| 531 | Sub-Work :-(6) Infrastructure Development and Retofitting works under AIC at Directorate of Science & Technology, Itanagar. |
| 532 | WALK WAYS FOR PEDESTRIAN & CAR PARKING RESERVATIONEarth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil androck), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 533 | Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade |
| 534 | Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (i) for grading- I Material |
| 535 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 536 | Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing ) |
| 537 | Centring and shuttering including strutting proping etc. and removal of form work for: a) Foundations and plinth |
| 538 | Chequered terrazzo tiles 22 mm thick with marble chips of sizes upto 6mmin floors on 25 mm thick bed mortar 1:3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: a) Light shades using white cement |
| 539 | Providing and installation of Tactile Tiles of suitable warning and guiding indicator blocks as per the Standard Factory manufactured Specification conforming to the requisite IS code of manufactuering on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete: |
| 540 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories &stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waistslab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 541 | Supply and providing of brailled signage boards for disabled assessibility of standard acrylic vinyle material as per the direction of the Engineer in charge. |
| 542 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorisin g glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.) |
| 543 | Traffic Cone (Provision of red fluorescent with white reflective sleeve traffic cone made of low density polyethylene(LDPE) material with a square base of 390 x 390 x 35 mm and a height of 770 mm, 4 kg in weight, placed at 1.5 m interval, all as per BS 873) |
| 544 | Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/ bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. |
| 545 | Street Lighting (Providing and erecting street light mounted on a steel circular hollow pole of standard specifications for street lighting, 9 m high spaced 40 m apart,1.8 m over hang on both sides if fixed in the median and on one side if fixed on the footpath, fitted with sodium vapour lamp and fixed firmly in concrete foundation.) (ii) For fixing in Footpath |
| 546 | Cable Duct Across the Road (Providing and laying of are inforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cut sand toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill of granular material over top and sides of RCC pipe as per IRC:98-1997,bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per IRC: 98 - 1997 and approved drawings.) (iii) Triple Row for three utility services |
| 547 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 548 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 549 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and switch, connection etc. as required. |
| 550 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 551 | MCCB, MCB & DB’S: Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incomming and outgoing circuits, duly prewiredwith suitable size FRLS PVC insulatedcopper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate,interconnections , power painted i/c earthing etc. as required.(But without MCB/ RCCB/ Isolator). (2 + 4) way/6way, Double door |
| 552 | Supplying and fixing30A, 440V, TPN industrial type, socket outlet with 4 pole and earth metal enclosed plug top alongwith 30A C series TPMCB, in sheet steel enclosure, on surface or in recessed with chained metal cover for the socket outlet and complete with connections, testing and commisioning etc as required. |
| 553 | Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors outgoing circuits, duly prew interconnections, powder painted including earthing etc. asired with suitable size FRLS PVCfor all incoming and insulated copper conductor up to terminal blocks, tinned copperbus bar, neutral link, earth bar, din bar, detachable gland plate, required.(But without MCB/ RCCB/ Isolator). 4 way (4 + 12), Double door |
| 554 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a)Single pole |
| 555 | (b) Single pole and neutral |
| 556 | Supplying and fixing following rating, Double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps |
| 557 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps |
| 558 | CABLE TRAYS: Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness |
| 559 | Providing and fixing M.V. danger notice plate of 200 mm X 150mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 560 | EARTHING: Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 561 | Earthing with G.I. earth plate 600 mm x 600 mm x 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charchol/coke and salt as required. |
| 562 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 563 | MV CABLE & LAYING: Supply of Alluminium conductor, PVC/XLPE insulated, armoured, overall PVC sheathed 1100 Volts Grade Power Cables Confirming to IS 1554 / 7098 ( Part - I ) 1988 with latest amendmentswith all accessories of Cable lug, pin etc of following sizes : 4 X 10 sq. Mm |
| 564 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. Mm |
| 565 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (Clamped with 1mm thick saddle) MV CABLE JOINTING & END TERMINATION |
| 566 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 3½ X 240 sq. mm |
| 567 | (b) 3½ X 50 sq. mm |
| 568 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 569 | Supply, Installation, testing and Commissioning of Weather proof Lighting Fixtures and Accessories as per standard vendors specification ( All lighting fixttures provided with required no. of double compression Nickel plated brass cable glands and stopping plug). SITC of WP 60 Watt LED Glass Type Lighting fixture with toughened glass and mesh suitable for LED lamp with integral type control gear box as per the standard available with vendor. |
| 570 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 no. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 571 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. 150 mm dia |
| 572 | Printing new letter and figures of any shade (Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade) (i) Hindi ( Matrascommas andthelike notto bemeasuredandpaidforHalf letter shall be counted as half ) |
| 573 | (ii) English and Roman |
| 574 | Carving of Brailles in SS Pipe and other metal sheet for enabling Signs in Handrails and Hand Sign Boards for Divyanjans. |
| 575 | RETROFITTING WORKS IN RAMPS, STAIRCASE, PASSAGE CORRIDORS , COUNTERS ETC. Providing and fixing 85x42 mm chromium plated brass pull bolt lock with necessary chromium plated brass screws, nuts, bolts and washers etc. complete |
| 576 | Providing and fixing of Reflective Fluorescent anti skid PVC Strips in Steps & Corridors. |
| 577 | (Providing with SS Guiding Studs for affixing in existing flooring tiles/ Stone works as Guiding pattern block signs)Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 578 | (Providing with SS Warning Studs for affixing in existing flooring tiles/ Stone works as Guiding & Warning pattern block signs) Road Markers/ Road Stud with Lense Reflector (Providing and fixing of roadstud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 579 | Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) conforming to IS: 14587:1998 marked, with (one side decorative and other side balancing lamination and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brandwith necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete. 25 mm thick |
| 580 | Providing and fixing 25 mm thick shutters for cup board etc. : Panelled or panelled & glazed shutters : 9.16.1.2 Second class teak wood including iSi marked nickel plated bright finished M.S. piano hinges with necessary screw. |
| 581 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour and shade 8.2.2.1 - Area of slab upto 0.50 sqm |
| 582 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete |
| 583 | Painting two or more coats (excluding priming coat) with superior ready mixedpaintfor woodwork of approved brandand manufacture in allshades on new work to give an even shade |
| 584 | RETROFITTING WORKS IN TOILET BLOCKS29-09-2021 Demolishing brick work in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 585 | Dismantling wood work of sectional area 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead. |
| 586 | Taking out doors, windows and clerestory windows shutters (steel or wood) including stacking within 50 m lead. a) Of area 3 Sq.m. and below |
| 587 | Dismantlingthe tilework infloors androofs laidincement includingstacking of materials within 50 m lead. a) For thickness of tiles 10 mm to 25 mm |
| 588 | Demolishing RCC work including stacking of steel bars and disposal of unserviceable materials within 50 metres lead. |
| 589 | Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth. |
| 590 | Extra for half brick masonry in super structure above plinth level and up to floor two level. |
| 591 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame |
| 592 | Providing and fixing to existing door frames.: 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge |
| 593 | Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete. a) 125 x 65 x 2.12 mm |
| 594 | Providing and fixing MS sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete. a) 300 x 16 mm |
| 595 | Providing and fixing MS tower bolts (barrel type) with necessary screws etc complete. a) 250 x 10 mm |
| 596 | Providing and fixing MS handles with necessary screws etc complete. a) 125 mm |
| 597 | Providing and fixing MS Hooks and Eyes. a) 300 mm |
| 598 | Providing and fixing MS safety hasp and staple with necessary screws etc complete. a) 150 mm |
| 599 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 600 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 601 | 20 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 602 | Extra for plaster to ceiling above 5 m height from floor lavel for every additional height of one metre or part there-of. |
| 603 | Extra for providing and mixing water proofing materials in proportion recommended by the manufacturers. |
| 604 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 605 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : Two coats |
| 606 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.2-W.C. pan with ISI marked black solid plastic seat and lid |
| 607 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1-Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 608 | Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : 17.6.1- Single squatting plate with 5 litre P.V.C. automatic flushing cistern |
| 609 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a)White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 610 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Semi rigid pipe 17.28.1.1 - 32 mm dia |
| 611 | Providing and fixing 100 mm sand cast Iron grating for gully trap |
| 612 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 17.32.4 - Rectangular shape 1500x450 mm |
| 613 | Providing and fixing toilet paper holder : 17.34.1- C.P. brass |
| 614 | Providing and fixing soil, waste and vent pipes : 75 mm diameter : 17.35.2.1- Sand cast iron S&S pipe as per IS: 1729 |
| 615 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 17.36.1 - 75 mm dia pipe |
| 616 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 18.7.1 15 mm nominal outer dia Pipes |
| 617 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 18.50.1- 15 mm nominal bore |
| 618 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms |
| 619 | Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 18.84.1-15 mm nominal bore |
| 620 | Providing and fixing chest support grab for urinalof Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 621 | Providingfixing and installation offoldable grab bar near WC & wash basin etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 622 | Providingfixing and installation ofD"handles of cercular section etc complete of Standard specification suited for Person with Disabilities as per the Direction of the Engineer in charge. |
| 623 | Supply, Installation, Testing & Commissioning of Drinking Water fountain ( delivery output- 32 Litres per hour) with temperature adjustment system with Flexible bubbler guard having heavy guage Galvanised steel frame meeting the needs and as per the set conforming to IS standard of the Phusically challenged and the able-bodied. |
| 624 | Provisioning for Design, Supply, Installation, Testing & Commissioning of Wheel Chair Stair Lift/ Platform lift of mechanical device for Lifting people up and down stairs mounted and powered trail channel as per the Standard Operation Procedure of the manufacturer and GAD/QAP approval from the engineer in charge with features of joystick remote operated hand held in action and swivel seat comfort arrangement, also built in with 6 safety cut out sensors to detect possible obstructions & objects in elevation operation with net total carrying capacity of single unit to the maximum of 130 kg (287 lb) and speed @ 0-100 mm per Sec. Total rail flight till G+2 building height in total. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
