|
| 1 | Charges for Docking / un - docking or beaching / un -beaching of the vessel |
| 2 | Dock hire charges (No extra dock hire charges will be entertained) |
| 3 | Mooring Charges for before and after dry-dock as well as during afloat repair works |
| 4 | Charges for ultrasonic testing of underwater hull and above water plates, onboard deck etc with Authorized agency. The copy of UT Gauge report shall be submitted to the office after completion of UT testing for the vessel immediately. |
| 5 | Dismantling of propellers Port & STBD sides (Make: Madras Marine industries, Dia:700 mm, Pitch:630 mm, P/D:0.9, No of blades:04, Type: Fixed pitch, no: 02), propeller shafts, checking the trueness of the shaft (Make: Madras Marine Industries, Dia:72 mm, Material: Stain less steel, no: 02), propellers, re-metalling, renewal of cut lash bushes 4 nos etc. Suitable NDT (DP/MPI) to be carried out by ASNT Level II Technician for Propeller / Trail shaft. And re-fitting of the same along with propellers after balancing (dynamic balancing of the propeller should be done) properly including labour charges. |
| 6 | Cost of Spare parts wiil be reimbursed on (Actual+10%) basis |
| 7 | Dismantling of rudder (Type: Plate type, Make: Startek shipyard Pvt Ltd, Chennai, Shaft: Dia.70 mm) and rudder stock, inspection of trueness, re-building of the same, making of new bushes, brackets etc. if any Suitable NDT (DP/MPI) to be carried out by ASNT Level II Technician for Rudder Stock and re-fitting of the unit properly including labour charges. |
| 8 | Cost of Spare parts will be reimbursed on (Actual+10%) basis |
| 9 | Overhauling of all sea suction / discharge valvesin engine room, onboard deck properlylabour Cost. |
| 10 | Cost of Spare parts will be reimbursed on (Actual+10%) basis |
| 11 | Servicing the Remote-control system including renewal of cable (gear not engaging properly)labour cost |
| 12 | Cost of Spare parts will be reimbursed on (Actual+10%) basis |
| 13 | Renewal of under and above water level hull and onboard deck steel plates of 5 / 6 mm thick of ship building quality after cropping and removal of the damaged plates by gas cutting without any damages to other fittings & also section under water portion pipe to assed (to be done after getting ultrasonic test report and recommendation of Surveyor, Port Dept, Govt of Kerala including labour and material Cost. |
| 14 | Chipping, scrapping, wire brushing, buffing, etc of external hull plate from keel to water level of the vessel properly (initially clean with fresh water with jet). Painting of the area with 2 coat of marine epoxy, 2 coat of chlorinated rubber antifouling paint including labour and material Cost. |
| 15 | Surface preparation of entire deck (from water level to deck surface) and super structure including out fittings by chipping, scrapping, wire brushing, buffing, shot blasting etc properly such as onboard deck, anchor winch, anchor cables (after dismantling), air vent pipes, hand pumps, bollards, wheel house, top of galley, railings, hatches, wheel house doors, stern gear compartment inside (rear side of vessel) & other fittings etc including labour and material Cost |
| 16 | Painting of entire deck (from water level to deck surface) and super structure including out fittings such as onboard deck, anchor winch, air vent pipes, hand pumps, bollards, wheel house, top of galley, railings, hatches, wheel house doors, engine room inside (total sides, top & ladder and floor portion etc), stern gear compartment inside (rear side of vessel) & other fittings etc with 2 coat of epoxy primer and 2 coats of epoxy marine quality enamel of existing colour properly. The damaged exhaust pipe cladding shall be renewed with new one properly (both engines) including labour and material Cost. |
| 17 | Renewal of damaged fire hand pipe with new one. Including labour and material cost. |
| 18 | Repair of STBD side main engine silencer pipe leakage and Aux engine exhaust manifold outlet pipe leakage renewal with new pipe including labour and material cost including labour and material cost. |
| 19 | servicing of the fire engine water pump (is not working properly) and bilge pump (is not working properly) including labour and material cost. |
| 20 | Cost of Spare parts will be reimbursed on (Actual+10%) basis |
| 21 | Supply and fitting of Bilge and smoke alarm in engine room and audible to the wheel house. Including labour and material cost |
| 22 | Opening & Cleaning of Diesel tanks of capacity 04 KL (Port:02 Ton, STBD:02 Ton), fresh water tanks of capacity 02 KL (Port:01 Ton, STBD:01 Ton) in Engine room properly without any dust particles. After cleaning, the oils shall be stored in safe location and re-filled after the cleaning process. |
| 23 | Repair & strengthening of hatches (Size:600X600, coaming height:300) for Engine room exit (1 no), stern gear compartment door (1 no) & Accommodation (1 no) by renewal of rubber beading of (hardness between 30-40) with new ones & damaged hatches to be strengthened by plate welding at damaged portions including labour and material Cost. |
| 24 | Repair and strengthening of doors – 2 nos, ventilators – 4 nos, Life Buoy holder – 3 nos, by renewal of rubber beadings with new ones & damaged or corroded portions to be strengthened by plate welding at damaged portions including labour and material Cost. |
| 25 | New sewage tank to be fitted with 500ltr capacity along with a pump and connection pipes with toilet outlet to the tank, shore connection flange to be fitted and also supply of hose of required length 30m to pump the waste including labour and material cost. |
| 26 | Fitting of Zinc Anodes (Location: Hull side shell): Zinc anodes, Type: ZHW-043, Net wt.:3.9 kg, Gross wt.:4.3 kg, Dim: 220X115X30, Qty:12, properly including labour and material Cost. |
| 27 | Fitting of zinc Anodes (Location: Rudder, Korte nozzle & sea chest) Zinc anodes, Type: ZHW-055, Net wt.:5.0 kg, Gross wt.:5.5 kg, Dim: 300x90x40, Qty:10 properly including labour and material Cost. |
| 28 | Renewal of damaged air vents 2 no’s, door steps - 3 no’s, bollard top plates properly including labour and material Cost. |
| 29 | The guard rails with pipes fitted onboard Port & STBD sides to be strengthened by proper welding etc. , the damaged pipes to be renewed with new ones including labour & material Cost. |
| 30 | Search light 500 / 200 watts, navigational lights (above wheel house green and red) are not working and making them fully functional by wiring, renewal of holders with new ones etc including labour. |
| 31 | Cost of Spare parts will be reimbursed on (Actual+10%) basis |
| 32 | Re writing of vessel name, logo (IWAI), registration no, Port of registry, GRT on 4 locations of the vessel with size: 200 mm x 200 mm, load line, draft marking etc and on LSA & FFA vessel name, reg no, port of registry to be marked clear visibility including labour and material Cost. |
| 33 | Life buoy as per LSA plan shall be supplied of good quality |
| 34 | The Damaged Plywood laminations of the inside walls of the wheel house cabin shall be renewed with new one’s including labour and material cost |
| 35 | The following Fire extinguishers to serviced, hydraulic testing & refilling with new one. Labour and material cost |
| 36 | Foam portable type - 9 lt |
| 37 | 9 lt water co2 portable extinguisher |
| 38 | Portable DCP extinguisher capacity-10 kg |
| 39 | Damaged bulb holders to be renewed and all electrical lines in Engine room to be made operational with new supply of lights |
| 40 | Chipping, scrapping, wire brushing, buffing etc of engine room bilge / bottom properly painting of the area including labour and material cost. |
