|
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sum on plan) including disposal ofexcavated earth, lead upto 50m and all lift upto 1.5m, disposed earth to be levelled and neatly dressed:All kinds of soil |
| 3 | Excavating trenches of required width for pipe cables, etc. including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 Mtr. including taking out the excavated soil, and then returning the soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil as directed within a lead of 50 Mtr.:All kinds of soil :-Pipes cables, etc. exceeding 80mm dia but not exceeding 300mm dia. |
| 4 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15cm deep and disposal of rubbish lead up to 50 Mtr. and lift up to 1.5 Mtr.:All kinds of soil |
| 5 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 40mm nominal size). |
| 6 | 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 7 | Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size). |
| 8 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggre -gate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 9 | Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.M20 grade Nominal Mix / Design Mix |
| 10 | Add extra for providing richer mixes respectively at all floor levels :-Providing M-25 grade concrete by using min 410 kg of cement per cum instead ofM-20 grade design mix. |
| 11 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. |
| 12 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. :-Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 13 | Half brick masonry in Superstructure , above plinth level upto floor Vlevelusing bricks of designation 75 : - Cement mortar 1 : 4 (1 cement : 4 coarse sand) |
| 14 | Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 ( 1-Cement : 6-Sand) |
| 15 | Random Rubble stone masonry with hard stone in superstructure aboveplinth level and upto five levelabove 30cm. thick walls in : Cement Mortar 1:6 ( 1-Cement : 6-Sand) |
| 16 | Providing and fixing horizontal chajja of Red/ White sand stone 40 mm thick and upto 80 cm projection in cement mortar 1:4 (1 cement : 4 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. |
| 17 | Providing dab stone over Chajjas duly fixed in cement sand mortar 1:6 complete :80mm thick. |
| 18 | Supplying and fixing in walls machine cut and polished stone shelves, tands andin CM 1:3 with machine cut edges :Kota stone 25 to 30mm thick. |
| 19 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. 15-18 mm thick laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. 25-09-2021-Jhunjhunu / Jalore (Red / Choclate Colour) : |
| 20 | Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite Work |
| 21 | Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete |
| 22 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure \"A\":35 mm Thick :Commercial Veneer both side |
| 23 | Extra for providing external lipping with 2ndclass teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13. |
| 24 | Providing and fixing M.S. sheet 1mm thicksingle leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint |
| 25 | Extra for double leaf shutters. |
| 26 | Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : Windows side hung /Ventilators top or centre hung (openable) |
| 27 | Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. |
| 28 | Providing and fixing Square bars or other flat welded to window, ventilatiors etc. |
| 29 | Grading roof for water proofing treatment withwater proffing compoundCement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 30 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : |
| 31 | Making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1 : 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1 : 3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. |
| 32 | Providing & laying broken glazed titles on roof ( broken glazed tilesnot less than 9 Kg/Sqm) on top of hot bitumen @ 1.7 Kg/Sqm. (1.40 Kg ofVG-40 (30/40 )grade and 0.30 Kg/Sqm. OfVG-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of Engineer-in-charge. |
| 33 | Kota stone slab flooring 25 mm thick over 20 mm (average) thickbase laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing completewith base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :-For area of each slab from 2001 to 5000 Sq.Cm |
| 34 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete : - For area of each slab upto 2001Sqcm |
| 35 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : - 25 mm thick |
| 36 | 20mm thick. |
| 37 | 12mm thick. |
| 38 | 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3-fine sand) |
| 39 | Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete |
| 40 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches by sandla/loi. (only for colour changing ). |
| 41 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:Newwork(twoormorecoats)overandincludingscrappingandprimingcoatwithcement primer. |
| 42 | Removing dry or oil bound distemper by scrapping sand papering and preparing surface smooth including necessary repairs to scratches by sandla/loi and all scaffolding (for colour changing only) |
| 43 | Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). |
| 44 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : Two or more coats on new work |
| 45 | Applying priming coat : - With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. |
| 46 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead :With cement mortar 1 :4 ( 1 cement : 4 coarse sand) |
| 47 | Renewing glass panes and refixing existing wooden fillets : - 4mm thick plain glass panes. |
| 48 | Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc. |
| 49 | Repair to damaged cement plaster of stone chajja with CM 1 : 3 of required thickness on top &bottom as per existing pattern and making patta etc complete up to three floor level as per direction of Engineer in charge including all necessary scoffolding etc |
| 50 | Repairofdoor,windowshuttersincludingcostofmaterialandlabourforchangeofdamaged : - (a) (i) Aldrop of mild Steel : - 12\" long x12mm dia |
| 51 | 8\" long x 10mm dia |
| 52 | Stopper of Aluminium with : - Double Rubber Gutka |
| 53 | Steel Hinges : - For Wooden Chowkhat 4\" size |
| 54 | For Stone Chowkhat ,4\"size |
| 55 | Mild Steel Tower Bolt 6\" long |
| 56 | Steel Handle 6\" size |
| 57 | Demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineer-in-charge. |
| 58 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. : - 1: 3: 6 or richer mix. |
| 59 | Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : - In lime mortar. |
| 60 | Dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead : - Of area 3 square meter and below. |
| 61 | Dismantling GI pipes (external work) including excavation and refilling trenches after taking out the pipes and including stacking of pipes within 50 meter lead : - 15mm to 40mm nominal bore. |
| 62 | Dismantling CI pipes including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into block, including stacking of pipes lead at site within 50 meter, of dia : - Up to 150mm dia. |
| 63 | Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. |
| 64 | Dismantling CC jali including cost of making grooves in plaster and making good and including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.. |
| 65 | Providing and fixing factory made of uPVC Extruded section having an overall dimension as below (tolerance+/-1mm) with wall thickness 2.0mm+/-0.2mm,corners of the door frame to be mitred and welded of plastic ,galvanized brackets and stain less steel screws.The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19x19mm and 1mm+/-0.1mm wall thickness and 3 nos.stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge. : -Extruded section profile size 48x40 mm |
| 66 | Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with 7mm (5mm +2mm) thick x 15mm wide PVC sheet bending on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the ‘C Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacture’s specification & drawing.(For W.C.and bathroom door shutter). |
| 67 | P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor : - Size 580x440mm. |
| 68 | P & F WVC wash basin (1st quality, I.S. : 2556 Mark) of approved make with C.I. brackets duly painted, 1 No. 15 mm C.P. Pillar cock (IS : 8934 Mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall.: - Size 580 mm x 450 mm |
| 69 | P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor : - Fire clay glazed kitchen sink (I.S. Marked) size 600 x 450 x 250mm. |
| 70 | P& F waste Pipe with all fitting : - P.V.C with PVC nut 32 mm |
| 71 | P.V.C. with C.P. nut 40 mm dia |
| 72 | P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make (Atul, Modi Guard, Saint Gobin or equivalent) complete with 6mm thick commercial ply base fixed to wooden screws & washers. : - Size 600 x 450mm x 4 mm thick |
| 73 | P & F Towel Rail or Ring of approved quality/make. : - Synthetic Material(PTMT) of approved quality/make size 525 x90 x 75mm |
| 74 | P & F Grating of approved quality/make : - Synthetic Material(PTMT)of approved quality/make size 125mm dia. |
| 75 | Labour Charges for removing WVC pan : - Indian/Orissa pan |
| 76 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in charge in skiriting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white mixed with pigment of matching shade complete. |
| 77 | Providing and laying Ceramic MAT floor tiles(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown of any size, laid on 20 mm thickbed of cement mortar 1:4 (1 cement : 4 coarse sand)including pointing in white cementmixed with pigment of matching shade complete. |
| 78 | Making connection of G.I. distribution branch with G.I. main including all fitting. : - Upto 25mm dia |
| 79 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make : - Synthetic Material(PTMT) bib cock of approved quality/ make, nominal bore, 15mm, 86 mm long. : - (-do-) Fancy Type, 122 mm long. |
| 80 | (-do-) Long Body, 175 mm long |
| 81 | P & F Stop Cock(IS :8931 Mark), superior quality & ofapproved make : - C.P. Brass 15mm nominal bore. |
| 82 | P & F Ball Cock (IS :1703 Mark) with Rod& P.V.C. Ball complete : - Brass wt.400 gm,15mm. |
| 83 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. : - C.P. Inlet connection 15mm.Brass (IS : 8931 marked) |
| 84 | (-do-) 450mm. |
| 85 | P & F 15 mm. Dia Connection Pipe of approved quality/make : - PVC pipe withC.P. Brass nuts upto length, 300mm : - (-do-) 450mm. |
| 86 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : -Gun-metal 15mm nominal bore. |
| 87 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design : - 500 litres capacity. |
| 88 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) : - 20mm nominal outer dia pipes |
| 89 | 25 mm nominal outer dia pipes |
| 90 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement ,trenching refilling & testing of joints complete as per direction of Engineer in Charge. (External work). : - 20mm nominal outer dia pipes |
| 91 | Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) all around S.W. pipe including 15 Cm. thick bed concrete (Width W= Diameter of pipe in Cm+30 Cm.)( Excluding cost of pipe) : - 100mm dia S.W. pipe |
| 92 | P & F Sand –cast Floor Trap (Nahni) of (IS:1729 mark) of approved quality/make with socket down or hinged grating including cutting and making good the floor. : - Size 100 x 75mm |
| 93 | P & F Sand-cast Iron `P` or `S` Trap (IS:1729 make) of approved make. |
| 94 | Labour charges for making connection of sewer line through main hole. |
| 95 | Making connection with existing G.I. pipe lines of all sizes. |
| 96 | Labour charges for removing C.I./A.C. pipes of all sizes including accessories with care and stacking of useful material. |
| 97 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. : - 75 mm dia |
| 98 | 110 mm dia |
| 99 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: - Door Tee : - 75mm dia |
| 100 | 110mm dia |
| 101 | Bend 87.5 : - 75mm dia |
| 102 | 110mm dia |
| 103 | Door Bend (Top Side) : - 75mm dia |
| 104 | 110mm dia |
| 105 | Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: - Size 300 Cm. dia outside & 300 Cm. depth . |
| 106 | Carriage of Building Rubbish Stone metal (Grit and ballast etc.) with lead of 10 Km. |
| 107 | Carriage of Earth, Sand, Lime, Morrum manure or sludgewith lead of 10 Km. |
| 108 | PART- C :-Internal Electrical work in Residential Police Line Sawai Madhopur |
| 109 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) ofapproved make in surface / recessed ISI marked medium duty PVC conduit & it\"s accessories, round tiles,Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch,Modular plate with grid plate,screws,making connections, testing etc. as required. |
| 110 | Short point (up to 3 mtr.) |
| 111 | Medium point (up to 6 mtr.) |
| 112 | Long point(up to 10 mtr..) |
| 113 | Wiring of 3 pin 5 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) of approved makein surface / recessed ISI marked medium duty PVC conduit & it\"s accessories, Hot Dipped Galvanized M.S Modular box of 20 SWG with earth terminal, 6 A modularswitch, 6 A modular socket, Modular plate with grid plate, screws, making connections, testing etc. as required. |
| 114 | On board |
| 115 | Supplying and fixing of power plug point Modular accessories on hot dipped galvanized modular on surface or in recessed with suitable size of grid plate with cover plate including cost ofmodular 16 amp. Switch and socket outlet, making connection , testing , etc. as required. |
| 116 | S&F following sizes (dia.) of ISI marked medium duty PVC conduit along with accessories in surface / recessed using saddles, clamps, fastener as required includingcutting the wall, covering conduit and making good the same as required. |
| 117 | 20 mm |
| 118 | 25 mm |
| 119 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existingsurface or recessed conduit/casing capping including making connections etc. as required. |
| 120 | 2 x 2.5 sq. mm. + 1x1.5sqmm |
| 121 | 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. |
| 122 | 2 x 6.0 sq. mm. + 1 x 2.5 sq. mm. |
| 123 | P & F IS:371 marked6 amp surface type ceiling rose including making connection testing etc. as required. |
| 124 | P & F ISI marked6 amp bakelite batten/angle holder including making connection testing etc. as required. |
| 125 | P & F following modular accessories made out of unbreakable and fire retardant poly carbonate with silver contacts including making connections testing etc. as required |
| 126 | 5 step fan regulator 2 Module |
| 127 | P & F double ball bearing capacitor start, aluminium body & blade ceilingfanwith down rod up to 30 cm with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. |
| 128 | 1200 mm sweep |
| 129 | P&F of IP 20LED tube light 20W with external batten made from CRCA sheet steel suitable to replace T-8/T-12 tubelights,integral driver, 2000 lumens +/- 5% tolerance,system lumens efficacy of 100 lm/watt minimum, expected life time of 25000 burning hours, CCT 5700K, ANSI, CRI 80, Driver efficiency >85%, Life expectancy of driver min. 30000 hrs. PF 0.95 at full load/ 230 volt AC. |
| 130 | P & Fof IP20 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Downlight with die-cast aluminum housing & Heat Sink for heat dissipation, high purity reflector with external BIS certified 2.5 KV surge protected driver having efficiency > 85% and in compliance to IEC standards. System Lumen efficacy of = 100 lm / watt andlife time of minimum35000 Burning Hours with 70% of intial Lumen maintaned, CCT 3000°K / 4000°K/ 6000°K , maximum power consumption should not more than the specified rating and Fixture shall be of CE complianed. |
| 131 | Surface Mounting |
| 132 | LED Downlight 12 W |
| 133 | P & F ISI marked single tone electronic call bell including making connection testing etc. as required. |
| 134 | P&F Recessed/ Surface mounting heavy duty horizontal type sheet steel Distribution board phophatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link and din bar,masking sheet, conforming to IS13032 & IS8623 including making internal DBterminations with copper lugs , testing etc. as required. |
| 135 | Double door (single phase) |
| 136 | 12 Way |
| 137 | P&F 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic) ISI marked IS 8828(1996)]/ conforming to IEC 60898 in existing board/sheets including making connections, testing etc. as required. |
| 138 | Single pole MCB |
| 139 | 6 A to 32 A rating |
| 140 | Double pole MCB |
| 141 | 40 A to63 A rating |
| 142 | P/Laying P.V.C./ XLPE insulated & P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor of IS:1554 P-I / IS :7098 P - I of Group 1 of approved makein ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,IInd class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. |
| 143 | 10.0 Sq.mm |
| 144 | 2 core |
| 145 | Maintenance free Gel EarthingwithPipe in pipe / Pipein striptechnologyfilled with anti corrosive conductive compound ( CPRI Tested )below the ground in 150 - 200 mm dia. earth pit & surrounding filled with required mineralfillingcompound ( MFC should have hygroscopic property to retain the moisture for long time to create low resistance zone) and C.C.finished chamber covered with hinged type with locking arrangement C.I. Cover,C.I. Frame of size 300mm x 300mm complete testing of earth resistance as required. of following sizes. |
| 146 | With Pipe in Pipe Technology (Inner pipe dia. / Outer pipe dia. ) 80 - 100 micron GI Coating |
| 147 | GI pipe 2000 mm long, 50 / 25mm, Terminal 12 mm GI Strip |
| 148 | S & Laying following size earth wire/stripin horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. as required. |
| 149 | 8 SWG copper Wire |
| 150 | P&F of Double ball bearing, capacitor startsingle phase metallicblade fresh air fan, in existing opening including cost of hardware , flexible copper conductor ,making connections, testing etc. as required. |
| 151 | 300 mm sweep |
| 152 | P & F phenolic laminated sheet 2.0 mm thick of size 75 mm dia. Including screws, cup washer as required. |
| 153 | P&F of RCBO with overload, short-circuit and earth leakage protection ISI marked (IS12640)/ conforming to IEC 61009/1 complete in all respect including making connections, testing etc. as required. |
| 154 | Two pole 100/300mA sensitivity |
| 155 | 40 A rating |
