Construction Of 01 No. Sbdtw Dia By Manual Means Including Providing And Installation Pump Motor Set, Electrical Panel Board, Laying Distribution System Etc. Within The Jurisdiction Of Dws Sub-Division, Santirbazar During 2021-22 (Deposit Work). Construct
Tender Value
2.80 Lakhs
Estimated cost
Bid Submission
18 Oct 2021
0 days left
EMD
2807
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Belonia → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of 01 No. Sbdtw Dia By Manual Means Including Providing And Installation Pump Motor Set, Electrical Panel Board, Laying Distribution System Etc. Within The Jurisdiction Of Dws Sub-Division, Santirbazar During 2021-22 (Deposit Work). Construction Of 01 No. Sbdtw Dia By Manual Means Including Providing And Installation Pump Motor Set, Electrical Panel Board, Laying Distribution System Etc. Within The Jurisdiction Of Dws Sub-Division, Santirbazar During 2021-22 (Deposit Work).
BOQ
| Sl. No. | Item Description |
| 1 | Drilling and boring pilot hole in any soil strata by manual means, collection of soil samples of different strata met with during drilling at various suitable levels, preservation ofsamples in polythene bags / sample boxes and disposal of excess soil or mud, including the cost for water etc. as required to maintain the pilot hole properly as per specification and direction of the Engineer - in - charge.i) 100 mm dia |
| 2 | Reaming of pilot hole to an enlarged bore hole in any soil strata by manual means, disposal of excess soil or mud, including the cost for water etc. as required to maintain the bore hole properly as per specification and direction of the Engineer - in - charge.i) From 100 mm dia pilot hole to 250 mm bore hole |
| 3 | Providing and fixing of UPVC end capsuitable for UPVC \"CM\" casingor\"CS\"casingor\"RS\"pipesasperspecificationand direction of the Engineer - in - charge. |
| 4 | i. 100 mm dia |
| 5 | iii) 150 mm dia |
| 6 | Providing & lowering of UPVC pipe as per IS:12818 after washing of the bore hole by manual means as per specification and direction of the Engineer - in - charge. |
| 7 | A.\"CM\" Casing pipei) 150 mm |
| 8 | A.\"CM\" Casing pipeii) 100 mm |
| 9 | B.\"RS\" pipei) 100 mm dia |
| 10 | Providing andfixingofUPVCreducersuitable forUPVC\"CM\" casingor\"CS\"casingor\"RS\"pipesasperspecificationand direction of the Engineer - in - charge.i) 150 x 100 mm dia |
| 11 | Providing and Shrouding of the deep tube well assembly with washed pea gravels ( 2.0 - 4.75 mm effective size ) as per specification ( IS : 4097) and direction of the Engineer - in - charge.i) Pea gravels obtained from Durgapur, West Bengal. |
| 12 | Washing and development of tube well by using hand pump or by any suitable method and testing of the well as per specification and direction of the Engineer - in - charge. |
| 13 | Supplying and fitting fixing of submersible pump of 2000 GPH capacity, 45 mtr head with motor of 3 HP/ required capacity, single phase including 40 mm dia 30.00 mtr heavy duty GI pump assembly and reducing socket, delivery band 90 degree non-return valve and fitting etc. as per directionof the Engineer-in-charge.a) 2000 GPH capacity submersible pump with 3 HP submersible Motor |
| 14 | Providing and fixing of housing clamp ( made with 12 mm thick MS sheet ) along with well cap (made with 10 mm thick MS sheet ) with necessary arrangements for SBDTW as per specification and direction of the Engineer - in - charge.i) 150 mm dia. |
| 15 | Supplying & fitting fixing of single phase motor starter unit (with 2 pole contactor, overload relay, volt meter & amps meter) 32 amps main switch (220 volt) of Havels/BCH/L&T make in KIOSK in/c necessary electric wiring and G.I pipe earthing etc complete as per direction of the Engineer-in-charge.i) For 3 HP Submersible motor |
| 16 | Providing and fitting fixing of Moulded Case Circuit Breaker (MCCB) of different Thermal release range , 415 + V, 50Hz (L & T, BCH, ABB make) as per specification and direction of the Engineer-in-charge.i) 25-32 Amps |
| 17 | Supplying & fitting fixing of panel box fabricated from 3/4 mm thich MS sheet of size width 450 mm x length 1200 mm x height 850 mm fitted with 4 nos support of 75mmx75mm ( 6 mm thick ) M.S angle and embedding in 1:2:4 c.c base (size 300mmx 300 mmx 600 mm) with proper locking arrangement and coated with anti corrosive paint(both inside & outside) in/c. necessary provisions for fitting fixing of single phase motor stater,main switch,energy meter etc. inside the box in/c. service connection within 50.00m length from LT line with roog for rain water protection etc. complete in all respect as per direction of the Engineer in charge. |
| 18 | Providingandfitting fixingsteel sheet enclosed switch fuse unit (suitable for DIN fuses) triple pole with neutrial link TPN,415/500 VoltL&T/Havels/BCH make etc. as per chapter 20 of CPWD specification and direction of the Engineer - in - charge.i) 32 Amps |
| 19 | Providing and fixing C.I. non-return valveofapproved quality as perof CPWD specification and direction of the Engineer - in - charge.i) 50 mm nominal bore |
| 20 | Trial run & commissining of the scheme in all respect as per specification and direction of the Engineer - in - charge. |
| 21 | Excavating trenches of required widthfor pipes, cables etc. including exacavation for sockets, dressing of sides where required, ramming of bottoms, depth upto 1500 mm(slope-1 in 200)including getting out the excavated soil and backfilling of soil as required after laying of pipeline, in layers not exceeding 200 mm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil with all required leads as per Chapter - 2 of CPWD specification and direction of the Engineer - in - charge.A. For UPVC pipes in new work a. In all kinds of soili. For pipes not exceeding 90 mm dia |
| 22 | Providing and fixing G.I. pipes medim class as per IS : 1239 with latest amendment complete with G.I. fittingsincluding trenching and refilling, cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge.A. External worki) 40 mmdia. nominalbore |
| 23 | Providing and fixing G.I. Bend /elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge.i) 40mm dia |
| 24 | Providing and fixing G.I. socketas per CPWD specification and direction of the Engineer - in - charge.i) 40mm dia |
AI Tender Summary
Tender Timeline
Sep 28, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedOct 18, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 18, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender