Public Works Department-PWD has published Balance Work For Construction Of 750 Capacity Auditorium Cum Workshop And Cafeteria Etc. For Tripura Medical College And Dr. Bram Teaching Hospital, Hapania, Tripura ( W ) ( Excluding Internal Electrification And Mechanical Work ) . Balance Work For . Submission Date for this Tender is 25-10-2021. Electrification Work Tenders in TMC, Hapania Tripura. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | SUB-HEAD : SH:- BALANCE WORK EARTH WORK |
| 2 | Cutting of trees (girth to be measured at a height of 1.0 m above the ground level ), includingcutting oftrunks, branches and removal of stumps & roots, refilling, compaction of backfilling and stacking of serviceable material and disposal of unserviceable materials by manual means with all lifts and lead upto 50 m as per clauses of Chapter - 2 of CPWD specification. |
| 3 | (i) Girth above 600 mm and upto 1200 mm |
| 4 | Earthwork in excavation in all kinds of soil over areas (exceeding average depth of 30 cm, 1.5 m in width as well as 10 sqm on plan ) including disposal of excavated earth lead up to 50 m outside the periphery of the area and lift upto 1.5 m, disposed earth to be leveled and neatly dressed as per clauses of Chapter - 2 of CPWD specification. |
| 5 | (i) Without dewatering |
| 6 | Filling in trenches, plinth, under floor, sides of foundations etc. with available excavated suitable soil in regular horizontal layers, each not exceeding 200 mm in depth with all lead and lifts, consolidating each layer by watering and ramming with steel rammers or 1/2 tonne roller as per clauses of Chapter - 2 of CPWD specification. |
| 7 | Filling in trenches, plinth, under floor, sides of foundations etc. with the approved materials obtained from borrow pits within a lead of 1000 m and all lifts, transporting to site, spreading in regular horizontal layers, each not exceeding 200 mm in depth, grading to required slope and compacting each layer by using plate compactor or by any suitable method at OMC as per clauses of Chapter - 2 of CPWD specification. |
| 8 | Extra for additional lead upto 1200 mtr. Including loading, unloading, transporting to disposal place by mechanical means complete.(Over item no-1.20) |
| 9 | Supplying of chemical emulsion ( Chloropyrifos emulsifiable concentrate of 20% as per IS : 8944 ) in sealed containers including delivery as specified as per clauses of Chapter - 2 of CPWD specification. |
| 10 | Charges for diluting and applying chemical emulsion for pre-constructional anti-termite treatment ( excluding the cost of chemical emulsion) as per clauses of Chapter - 2 of CPWD specification. |
| 11 | CEMENT CONCRETE WORK: |
| 12 | Providing and laying in position cement concrete of specified grade including the cost of Form work, all work upto plinth level as per clauses of Chapter - 4 of CPWD specification. |
| 13 | i) 1 : 3 : 6 ( 1 cement : 3 fine sand : 6 graded stone aggregate of 40 mm nominal size) { Top concrete layer for inside of drain / septic tank only} |
| 14 | REINFORCED CEMENT CONCRETE WORK : |
| 15 | Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10 Kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixture to site of laying, including the cost of form work but excluding finishing and reinforcement, including admixtures in recommended proportions ( as per IS : 9103 ) to accelerate or retard setting of concrete, improve workability without impairing strength and durability all works upto floor five level as per direction of Engineer-in-charge and as per clauses of Chapter - 5 of CPWD specification. |
| 16 | (i) All work upto plinth level: - M-25 grade reinforced cement concrete |
| 17 | (ii) All work above plinth level and upto floor five level, - M25 grade reinforced cement concrete. |
| 18 | Reinforcement for RCC works including straightening, cutting, bending, placing in position & binding all complete upto floor five level, as per clauses of Chapter - 5 of CPWD specification. (i) TMT bars |
| 19 | Providing and fixing sheet covering over expansion joints with iron screws as per design to match the colour / shade of wall treatment at all levels as per clauses of Chapter - 5 of CPWD specification. |
| 20 | (i) Aluminium fluted strips 3.15 mm thick:- 150mm wide |
| 21 | BRICK WORK |
| 22 | First class brick work in superstructure above plinth level upto floor five level including cost of all materials required and as per clauses of chapter-6 of CPWD specification. i) In cement mortar 1:5 ( 1 cement : 5 fine sand ) |
| 23 | Half brick masonry with first class bricks in foundation and plinth including cost of all materials required and as per clauses of chapter-6 of CPWD specification i) In cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 24 | Half brick masonry with first class bricks in superstructure above plinth level upto floor five level including cost of all materials required and as per clauses of chapter-6 of CPWD specification. i) In cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 25 | Extra for providing and placing in position 2 Nos. 6 mm dia M.S. Bars at every third course of half brick masonry including the anchorage in joints of 75 mm in each side in superstructure at all levels including cost of all materials required and as per clauses of chapter-6 of CPWD specification. i) In cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 26 | WOOD WORK |
| 27 | Providing wood work in frames of doors, windows, clerestory windows, partitions and other similar works and fixing in positionas per clauses of Chapter - 9 of CPWD specification. (i) Local teakwood |
| 28 | Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory windows including bright finished / black enameled M.S. butt hinges with necessary screws, (excluding paneling and or glazing,which will be paid for separately), but including the wooden beading of 20 x 12 mm for fixing panelling and or glazing as per clauses of Chapter - 9 of CPWD specification. |
| 29 | (i) Single leaf door shutter: - Local teakwood: - 35 mm thick shutters |
| 30 | Providing and fixing paneling / glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured ). Panelling / glazing forpanelledor panelled and glazed shutters 25 mm to 40 mm thick as per clauses of Chapter - 9 of CPWD specification. |
| 31 | i) Local teakwood 16 mm thick (Panneling) |
| 32 | ii) Frosted glass panes 4 mm thick (Glazing) |
| 33 | Providing and fixing factory made door frame ( single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60 mm width & 30 mm thickness and shall be fixed to wall as per instructions of Engineer-in-charge using 100 x 8 mm sheet metal CSK screws complete as per clauses of Chapter - 9 of CPWD specification. |
| 34 | Providing and fixing factory made door shutter 28 mm thick, made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71 mm width & 28 mm thick as styles and rails. Joints are made using solvent adhesive and GI "C" sections ( 39 x 19 x 0.6 mm thick) stiffener frame insert & telescopic polymeric "L" corners. The panel shall be filled with 3 mm thick high pressure compact laminate as per manufacturer"s specifications and direction of Engineer-in-charge, cover moulding shall be provided for covering, fixing screws and elegant look as per clauses of Chapter - 9 of CPWD specification. |
| 35 | Providing and fixing 12 mm thick and 100 mm wide pelmets with 25 mm diameter wooden curtain rods & bracket including fixing with 25 x 3 mm M.S. flat 10 cm long and plugs etc. complete with necessary screwsas per clauses of Chapter - 9 of CPWD specification. i) Local teak wood |
| 36 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flat, solid square or solid round bars etc. all complete as per clauses of Chapter - 9 of CPWD specification. (i) Fixed to openings in walls with rawl plugs, screws etc. |
| 37 | Providing hold fast of 40 x 5 mm flat iron including fixing to frame with 10 mm diameter bolts, nuts & wooden plugs and embedding in C.C. 1:3:6 (1 cement: 3 fine sand: 6 graded well burnt brick aggregate 20 mm nominal size) block of size 30 x 10 x 15 cm as per clauses of Chapter - 9 of CPWD specification. |
| 38 | Providing and fixing ISI marked aluminium sliding door bolts anodised (anodised coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade with necessary screws etc. complete as per clauses of Chapter - 9 of CPWD specification. |
| 39 | (i) 300 x 16 mm |
| 40 | ii) 250 x 16 mm |
| 41 | Providing and fixing ISI marked aluminium tower bolts anodised (anodised coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade with necessary screws etc. complete as per clauses of Chapter - 9 of CPWD specification: |
| 42 | (i) 250 mm x 10 mm |
| 43 | (ii) 200mm x 10 mm |
| 44 | Providing and fixing ISI marked aluminium handles with plate anodised (anodised coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade with necessary screws etc. complete as per clauses of Chapter - 9 of CPWD specification: (i) 150 mm |
| 45 | Providing and fixing ISI marked aluminium hanging floor door stopper anodised (anodised coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade with necessary screws etc. complete as per clauses of Chapter - 9 of CPWD specification. |
| 46 | STEEL WORK |
| 47 | Providing and fixing in position collapsible steel shutters with vertical channels 20 x 10 x 2 mm and braced with flat iron diagonals 20 x 5 mm with top and bottom rail of T - iron 40 x 40 x 6 mm with 40 mm dia steel pulleys complete with riveted bolts, nuts, locking arrangements, stoppers, handles etc. including applying a coat of priming coat of approved steel primer all complete as per clauses of chapter-10 of CPWD specification. |
| 48 | Providing and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and joined together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters including applying a coat of priming coat of approved steel primer all complete as per clauses of chapter-10 of CPWD specification: i) 80 x 1.25 mm MS laths with 1.25 mm thick top cover |
| 49 | Providing and fixing M.S. fan clamp of type I or II of 16 mm M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying of steel including painting exposed portion, all complete as per standard design as per clauses of chapter-10 of CPWD specification. |
| 50 | ALUMINIUM WORK |
| 51 | Providing and fixing aluminium work for doors, sliding doors, windows, ventilators, stair railing with hand rail and partitions with extruded built up standard tubular sections / appropriate Z sectionsand other sections of approved make conforming to IS : 733 and IS : 1285, , fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws all complete as per architectural drawings and the direction of Engineer-in-charge and as per clauses of chapter-24 of CPWD specification. ( Glazing and panelling to be paid for separately) |
| 52 | (i) For fixed portion - Anodised aluminium (anodised transparent or dyed to required shade according to IS : 1868 , minimum anodic coating of grade AC 15 ) |
| 53 | (ii) For shutters of doors, windows & ventilators or for sliding shutters of doors, windows & ventilatorsincluding providing and fixing hinges / pivots / rollers and making provision for fixing fittings wherever required including the cost of PVC / neoprene gasket required ( Fittings shall be paid for separately ). - Anodised aluminium (anodised transparent or dyed to required shade according to IS : 1868 , minimum anodic coating of grade AC 15 ) |
| 54 | Providing and fixing glazing in aluminium aluminium doors,windows, ventilator, shutters and partition frames with PVC / neoprene gasket etc. complete as per architectural drawings and the direction of Engineer-in-charge and as per clauses of chapter-24 of CPWD specification. |
| 55 | (i) With glass panes of 4.0 m thickness ( weight not less than 10.0 kg / sqm ) |
| 56 | (ii) With glass panes of 5.5 m thickness ( weight not less than 13.75 kg / sqm ) |
| 57 | Providing and filling the gap in between aluminium frame and adjacent RCC / brick work by providing weather silicon sealant over backer rod of approved quality as per direction of the Engineer-in charge as per clauses of chapter-24 of CPWD specification. i) Upto 5 mm depth and 5 mm width |
| 58 | Providing and fixing stainless steel ( SS 304 grade ) adjustable friction window stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete and as per clauses of chapter-24 of CPWD specification. i) 255 x 19 mm |
| 59 | Providing, Fixing and errection of 4.0 mm thick Aluminium composite panel (ACP) cladding of Aludecor/Durabuild/Alucobond or Similar approved make, fabricated to flat, smooth curved to required radius, circular ring cladding to shape as per requirement (exterior/interior surface), in metallic colours using prefabricated aluminium extruded profiles of Alloy 6063 T6 in chromatized finish to withstand the design wind pressure of 200 Kg/Sqm. The fastening brackets of Aluminium / Hot dip galvanized with SS 304 screws, fastners and anchor bolts complete with nylon separators to prevent bi-metallic contacts. ACP sheets will be fixed with both ways Norton tape and Dow Coring 995 structured sealant, including necessary scaffolding complete, as per approved architectural drawing and design or as directed by the Engineer-in-charge. |
| 60 | Providing, fixing & erection of semi unitized structural glazing with anodized or powder coated (of approved shade) aluminium section (of a company of reputed)in frame work with Hindalco Section no. 9187 or Similar approved, including fixing of 6.0 mm thick, Pyrolithick on - line coated solar heat reflective toughened glass (Glaverbal or Similar make) of approved colour. Glass fixing arrangement with aluminium structure with sub frame of appropriate sections. Structural silicone (Dow corning or Wakcher SG-18 or Similar make) will be used for fixing glass to subframe, joining line of glasses should be filled up with Polyurethane back up foam and weather sealant (Dow Corning or Wakcher make or Similar make). GI coated MS bracket of suitable design shall be fixed at every slab, beam (structural elements) to hold the main frame work, including necessary fixtures complete, EPDM quality gasket will be used on all necessary points and SS nut bolt, GI fastners will be used for fixing clamps, including necessary scaffolding complete, as per approved architectural drawing and design or as directed by the Engineer-in-charge. |
| 61 | FLOORING WORK |
| 62 | Providing and laying 40 mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 28 mm thick cement concrete 1 : 2 : 4 ( 1 ordinary cement : 2 fine sand : 4 graded stone aggregate 12.5 mm nominal size ) and top layer 12 mm thick with white, black, chocolate, grey, yellow, pink, blue or green marble chips of sizes from 7 mm to 10 mm nominal size laid in cement marble powder mix 3 : 1 ( 3 cement : 1 marble powder ) by weight in proportion of 2 : 3 ( 2 cement marble powder mix : 3 marble chips ) by volume including cement slurry etc. complete as per clauses of Chapter - 11 of CPWD specification: (i) Using white cement in top layer with no pigment |
| 63 | Providing and laying marble chips skirting ( upto 300 mm height ) rubbed and polished to granolithic finish, top layer 6 mm thick with white, black, chocolate, grey, yellow, pink, blue or green marble chips of sizes from 1 mm to 4 mm nominal size laid in cement marble powder mix 3 : 1 ( 3 cement : 1 marble powder ) by weight in proportion of 4 : 7 ( 4 cement marble powder mix : 7 marble chips ) by volume including cement slurry etc. complete as per clauses of Chapter - 11 of CPWD specification: (i) Using white cement in top layer with no pigment |
| 64 | Providing and fixing 18 mm thick Marble stone in floors over 20 mm thick bed ofcement mortar 1 : 3 ( 1 cement : 3 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishingcompleteas per clauses of Chapter - 11 of CPWD specification. |
| 65 | Providing and fixing Marble tiles in skirting, risers of steps, dado etc. ( upto 2 m height ) over 12 mm thick bed ofcement mortar 1 : 3 ( 1 cement : 3 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade completeas per clauses of Chapter - 11 of CPWD specification. |
| 66 | Providing and fixing precast chequered cement concrete tiles 22 mm thick, laid in footpath & courtyard, on 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing completeas per clauses of Chapter - 11 of CPWD specification. |
| 67 | Providing and fixing 18 mm thick Kota stone in floors over 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishingcompleteas per clauses of Chapter - 11 of CPWD specification: (i) Kota stone slab 25 mm thick |
| 68 | Extra for providing and laying marble flooring complete on treads & riser of steps not exceeding 300 mm in width including cost of forming, nosing etc. as per clauses of Chapter - 11 of CPWD specification. |
| 69 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 ( thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1 : 3 ( 1 cement : 3 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade completeas per clauses of Chapter - 11 of CPWD specification. |
| 70 | ROOFING WORK |
| 71 | Providing and fixing on wall face unplasticised rigid PVC (working pressure 4 kgf per sqcm ) rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion as per clauses of Chapter - 12 of CPWD specification. i) Single socketted pipes - 160 mm OD |
| 72 | Providing and fixing on wall face PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion as per clauses of Chapter - 12 of CPWD specification. |
| 73 | (i) Coupler: - 160 mm. |
| 74 | (ii) Single equal tee with door - 160 x 160 x 160 mm |
| 75 | (iii )Bend 87.5 degree - 160mm |
| 76 | Providing and fixing unplasticised PVC moulded pipe clips of approved design to unplasticised rigid PVC rain water pipes by means of 50 x 50 x 50 mm hard wood plugs, screwed with MS screws of required length including cutting brick / CC / RCC work and fixing with cement mortar 1 : 4 ( 1 cement : 4 fine sand ) and making good the wall etc. complete as per clauses of Chapter - 12 of CPWD specification. (i) 160 mm |
| 77 | FINISHING WORK |
| 78 | Extra for plastering on circular work not exceeding 6 m in radius complete including cost of materials required and as per clauses of chapter 13 of CPWD specification: (i) In two layer |
| 79 | 15 mm cement plaster in single layer including cost of materials required and finishing even and smooth and curing complete as per clauses of chapter 13 of CPWD specification: (i) Cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 80 | Neat cement punning including cost of materials required as per clauses of chapter 13 of CPWD specification. |
| 81 | Distempering with oil bound washable distemper of approved brand and manufacture and of required shade on new work ( two or more coats ), over and including a priming coat of cement primer to give an even shade complete including cost of materials required and as per clauses of chapter 13 of CPWD specification. |
| 82 | Finishing walls with premium acrylic smooth exterior paint of required shade of approved brand and manufacture on new work ( two or more coats applied @ 1.43 kg/10 sqm ) over and including base coat water proofing cement paint applied @ 2.20 kg/10 sqm complete including cost of materials required and as per clauses of chapter 13 of CPWD specification. |
| 83 | Painting on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint ( two or more coats ) of required colour of approved brand and manufacture to give an even shade on new work over and including a priming coat of zinc chromate yellow primer complete including cost of materials required and as per clauses of chapter 13 of CPWD specification. i) 100 mm. dia. |
| 84 | Painting with synthetic enamel paint ( two or more coats ) of required colour of approved brand and manufacture on new work to give an even shade including cost of materials required and as per clauses of chapter 13 of CPWD specification. |
| 85 | (B) SH:- ROOFING & SHEET COVERING STEEL WORK |
| 86 | Providing structural steel work in built up sections, trusses and framed work including cutting, welding, hoisting and fixing in position with holding down bolts and applying a priming coat of approved steel primer in steel Hollow Sections (TATA STRUCTURA make) etc. all in complete including all types of necessary scaffoldings etc. approved as per IS- 4923, Grade-yst 310 (material) specification. |
| 87 | ROOFING AND CEILLING WORK |
| 88 | Providingand fixing approved pre-painted Galvalume sheet (Hi-Rib Profile Sheet) made out of Cold Rolled Steel Coated with Zink-Aluminium Alloy (coating of 43.50% Zinc, 55.00% Aluminium & 1.50% Silicon) having Alloy coating AZ150/AZ100, Colour coated with high quality polyster coating with top coat of modified polyster of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both surface, protected with Guard film, yield/tensile strength minimum 550 mpa. etc. (Dyna Roof make) over a built structure including all types of necessary scafolding, installation / fixing inclusive all types of fixing materials nut, self drilling screws & caps, sealants, closures etc. all in complete as decided by the Engineer-in-Charge. (Non schedule / MR item) (i) 0.50 mm thick profile sheets. |
| 89 | Providingand fixing approved pre-painted Galvalume sheet (Ridges / Valley / Gutter / Flashing etc.) made out of Cold Rolled Steel Coated with Zinc-Aluminium, Alloy (coating of 43.50% Zinc, 55.00% Aluminium & 1.50% Silicon) having Alloy coating AZ150/AZ100, Colour coated with high quality polyster coating with top coat of modified polyster of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both surface, protected with Guard film, yield/tensile strength minimum 550 mpa. etc. (Dyna Roof make) over a built structure including all types of necessary scafolding, installation / fixing inclusive all types of fixing materials nut, self drilling screws & caps, sealants, closures etc. all in complete as decided by the Engineer-in-Charge. (Non schedule / MR item) (i) 0.50 mm thick & 610 mm width. |
| 90 | (C) SUB-HEAD : DISMANTLING |
| 91 | Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge. |
| 92 | Demolishing cement concrete manually / by mechanical means including disposal of material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge: (i) Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 93 | Demolishing reinforced cement concrete manually / by mechanical means including stacking of steel bars properly and disposal of unserviceable material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge. |
| 94 | Dismantling steel work in built up section in channels, angles, tees, flats including all gusset plates, bolts, nuts, cutting rivets, welding including dismembering and stacking of serviceable materials and unserviceable materials separately with all lifts and upto a lead of 50 m etc. complete as per direction of the Engineer- in-charge. |
| 95 | Extra for dismantling trusses, rafters, purlins etc. of steel work for every additional span of 1 m or part thereof beyond 10 m etc. complete as per direction of the Engineer- in-charge. |
| 96 | Extra for dismantling trusses, rafters, purlins etc. of steel work for every additional height of 1 m or part thereof beyond 5 m etc. complete as per direction of the Engineer- in-charge. |
| 97 | Carriage of dismantle materials such as trusses, rafters, purlines etc. of steel work from TMC Complex, Hapania to PWD Store, A.D. Nagar, Agartala up to lead of 12.00Km by mechanical transport including loading, unloading & stacking properly as per direction of the Engineer-in-Charge. |
| 98 | (D) SUB-HEAD : STAGE & SEAT |
| 99 | Providing and fixing 25 mm thick Marine plywood of make Greenply / Century ply or equivalent as per IS 710: 2010 over prepared structure as a supporting base in flooring of stage as per specification and as per direction of Engineer-in-Charge. |
| 100 | Providing and fitting and fixing 4 mm thick Marine plywood of make Greenply / Century ply or equivalent as per IS 710 : 2010 over 25 mm thick plywood as a supporting base in flooring of stage as per specification and as per direction of Engineer-in-charge. |
| 101 | Main Curtain motorized with pure velvet cloth,supplying,installation,testing & commissioning of motorized horizontal operated Main,Curtain mechanism with curtain controller unit complete with 1(one) HP 230volt single/three phase AC Motor,with cotton velvet cloth of approved make,shade & colour,in/c backing cloth of approved make,decorative bridle with ball fringes,tassels etc |
| 102 | Back Curtain (Manual) complete with black cotton cloth. |
| 103 | Frill Bar: Providing and fixing manually operation frill bar up & down system 100mm dia bearing fitted with pulley & MS bracket 8mm poly puppling rope 32 OD MS Black pipe & Black cloth complete set |
| 104 | Light Bar Wing System:Providing and fixing light bar mechanism consisting of 100mm dia bearing fitted with pully with MS bracket 6mm thick steel flexible wire adjustable stainer/rope clamp 48mm OD Black pipe & 1000kg capacity manual winch with paint complete set. |
| 105 | Wing Mechanism (Horizontal & Moveable) with linch OD pipe along with jute & black cloth. |
| 106 | Cyclorama frame & cloth (Bombay Dying) with 48 mm OD pipe-cross member 32 OD pipe with moveable mechanism consisting of wheels(150mm dia) |
| 107 | Providing, fitting and fixing curtain box with 40x40x6mm square hollow section and with 900 mm centre to centre horizontal bracing. Cover the frame with 6mm ply both side including painting one coat with red oxide and one coat with black synthetic enamel paint of the Engineer-in-Charge. |
| 108 | Decorative type front frill with double gathered best quality synthetic velvet cloth of approved colour in/c decorative frinches bridle & tassela complete with frame work of 25 mm OD GI black pipe, MS angle 40X40X6 mm with necessary fabrication complete, manually operation frill bar up & down system 100 mm dia bearing fitted with pully & MS bracket 8 mm pully pumping rupe in/c cost of all labourers carriage to work site & necessary taxes etc. complete as per direction of the Eng-in charge. |
| 109 | Supply, fitting & fixing of Auditorium chair of make GODREJ and Model No:-AUDI-II of shade Earth Song (Code No: V-08) as per direction of the Engineer in-Charge. |
| 110 | (E) SUB-HEAD : STEEL WORK, CATWAY ETC. |
| 111 | Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 112 | Providing and fixing in position 3mm thick M.S. sheet as a supporting base of catway and other structures includng cuttng, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete as required, as per specification and as per direction of Engineer-in-charge. |
| 113 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 114 | (F) SUB-HEAD : CEILLING |
| 115 | Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main |
| 116 | ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the Engineer-in-charge.: (i)With 20 mm thick beveled tegular mineral fibre false ceilingtile (NRC 0.7). |
| 117 | (G) SUB-HEAD : WALLING |
| 118 | Providing and Fixing Channeled Hi Density Fiber Board Wall Panel (woodworks) (WC01C28LUMW) perforated panels of width 128mm, thickness of 15mm and length 2440mm with minimum 830 kg/M3 density substrate with a laminated facing as per the approved shade/species & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a “Helmholtz” fluted perforation of 4mm width and 28 mm visible panel each. The panels shall provide a fire reaction of Class of 1 as per Part 7 of BS 476. The edges of the panels shall be “tongue-andgrooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing nonwoven acoustical fleece having NRC of 0.55. The panels shall be mounted on special aluminium splines using clips. Install wooden battens of section 50 mm x 50 mm or approved by the Architect on the solid wall horizontally using screws and plugs at spacing of 600 mm centre-tocentre. Screw the aluminium-extruded |
| 119 | keel for channeled wood works (GTPT001) over the lowest and second wooden batten at an on-centre distance of 600 mm. Install the first set of wooden panels by inserting the clips for border channeled woodworks (GTPT002) and insert the grove of the panel into the projecting flange of the aluminium clip. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing clips for inside channeled woodworks (GTPT003) into the next keel till the actual height is achieved. Use clips for borer channeled woodworks (GTPT002) to finish off the installation. Finish off the edges using wooden moulding of matching colour approved by the Architect, suitably fixed all complete as per drawings and specification and direction of the Engineer-in-Charge. |
| 120 | Providing and fixing in position wall panneling at all heights with 12.5mm thick perforated Gypsum Board panels / tiles made from plasterboard having glass fibre conforming to IS 2095 part 1 of size 595 X 595 mm having perforation of 9.7X 9.7 mm at 19.4mm c/c with centre boarders of 48mm & the site borders of 30mm having NRC (Noise Reduction Coefficient) of 0.65 (minimum) as per IS 8225:1987 Light reflectance of 85% (minimum). Non combustible as per DS:476 (part-4) fire performance as per BS:476 (part 6 & 7) humidity resistance of 100% thermal conductivity < 0.043W/mK as per ASTM 518: 1991 comprising of a frame made from especially fabricated galvanised mild steel size 48X34X36 mm are placed at 600mm center to center in a floor and ceilling channel section of size 50X32m fixed to the floor and soffit at 600mm centers using 12mm dia. 50mm long wage type expanded zink alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horizontal direction at 600mm center to center so as to form a grid of 600mmX600mm. |
| 121 | Resin bonded Glasswool of 24Kg / m3 and 50mm thickness is then to be inserted in the slots and finally Gypsum Board non combustible pannels / tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13X3.2mm on to this grid leaving and even groove of 1mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing compound and fibre joint tap roll 50mm wide (90 metre) roll and two coats of primer suitable for paneling as per manufacturer specification as per direction ofEngineer-in-Charge all complete. |
| 122 | (H) SUB-HEAD : WATER PROFFING |
| 123 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and as per direction of Engineer-In-charge complete in all respect.: (i) SBR Polymer (@10% of cement weight) modified cementitious bond coat @2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer |
| 124 | Extra for providing and laying of Fibre glass cloth over bonding coat of approved adhesive as per item no. 20.10, when the coat is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. |
| 125 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with : |
| 126 | (i) Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 127 | (ii) Cement mortar 1:3 (1 cement : 3 fine sand) |
| 128 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound, as directed by Engineer-in-Charge and consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 129 | (I) SUB-HEAD : SANITARY WORK |
| 130 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (i) White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 131 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (i) W.C. pan with ISI marked white solid plastic seat and lid |
| 132 | Providing and Fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : (i) One urinal basin with 5 litre white P.V.C. automatic flushing cistern. |
| 133 | Providing and Fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. Automatic flushing cistern, with fittings, standard size G.I. flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc. wherever required : (i) Single squatting plate with 5 litre P.V.C. automatic flushing cistern. |
| 134 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : (i) White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar taps |
| 135 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 136 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: (i) Kitchen sink without drain board : - 610x510 mm bowl depth 200 mm. |
| 137 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.: (i) Semi rigid pipe : - 40 mm dia |
| 138 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 139 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete |
| 140 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms. |
| 141 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms. |
| 142 | Providing and fixing on wall face unplasticised Rigid PVC, soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382leaving10mmgapforthermalexpansion: (i) Single socketed pipe - 110 mm OD |
| 143 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC, soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap forthermalexpansion: |
| 144 | (i) Coupler:110 mm |
| 145 | (ii) Single equal tee without door:110x110x110mm |
| 146 | (iii) Single equal tee with door :110x110x110mm |
| 147 | (iv) Bend 87.5:110mm |
| 148 | (v) Plain shoe :110mm |
| 149 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC, soil, waste & vent pipesbymeansof50x50x50mmhard woodplugs,screwedwithM.S.screwsofrequiredlengthincluding cutting brick work andfixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete.: (i) 110mm |
| 150 | (J) SUB-HEAD : WATER SUPPLY WORK |
| 151 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.: Internal work -Exposed on wall : |
| 152 | (i) 15 mm nominal outer dia .Pipes. |
| 153 | (ii) 25mm nominal outer dia .Pipes |
| 154 | (iii )40 mm nominal outer dia .Pipes. |
| 155 | (iv) 50 mm nominal outer dia .Pipes. |
| 156 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge: - Concealed work including cutting chases and making good the walls etc. |
| 157 | (i)15 mm nominal outer dia .Pipes. |
| 158 | (ii) 25 mm nominal outer dia .Pipes. |
| 159 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 160 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: (i) 15 mm nominal bore |
| 161 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.: (i) 15 mm nominal bore. |
| 162 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931: (i) 15 mm nominal bore |
| 163 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge |
| 164 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): |
| 165 | (i) 25 mm nominal bore |
| 166 | (ii) 40 mm nominal bore |
| 167 | (iii)50 mm nominal bore |
| 168 | (K) SUB-HEAD : ALLUMINIUM WORK |
| 169 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embrossed on the body / plate with double spring mechanism and door weight upto 125 kg. for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece MS sheet outer box with slide plate etc. complete as per direction of the Engineer-in-charge: (i) With stainless steel cover plate minimum 1.25 mm thickness |
| 170 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality completeas per direction of Engineer-in-charge: (i) Anodised aluminium of grade AC 15) |
| 171 | Providing and fixing 100 mm brass locks (best make of approved quality) with 6 levers without pair of handles for aluminium doors including necessary cutting and making good etc. complete as per direction of Engineerin-charge. |
| 172 | (L) SUB-HEAD : FINISHING WORK |
| 173 | 12 mm cement plaster of mix : (i) Cement mortar 1:4 (1 cement : 4 fine sand) |
| 174 | 6 mm cement plaster of mix : (i) Cement mortar 1:3 (1 cement : 3 fine sand) |
| 175 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : |
| 176 | (i) With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 177 | (ii) With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 178 | (M) SUB-HEAD : FLOORING |
| 179 | Providing and laying cement concrete 1:2:4 (1 cement: 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips etc. complete: (i) 40mm thick. |
| 180 | Providing and laying ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete. (i) Anti skid tiles : - Ceramic tiles 1st quality 300X300mm in all shades and designs |
| 181 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete: (i) Soluble Salt Stainfree vitrified tiles : - Size of tile 60x60 cm |
| 182 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622 -2017, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. (i) Soluble Salt Stainfree vitrified tiles - Size of tile 60x60 cm |
| 183 | Providing and fixing Vitrified chequered floor tiles 300 x 300 mm or more, (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 4457-2007, of approved brand & manufacturer, laid in footpath & courtyard, over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) including grouting of joints (Payment for grouting of joints to be made separately) |
| 184 | (N) SUB-HEAD : WOOD WORK |
| 185 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (i) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 186 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters: (i) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 187 | Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : (i) 250 x 10 mm |
| 188 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 189 | Providing and fixing bright finished brass handles with screws etc. complete: (i) 125 mm |
| 190 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 191 | Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete |
| 192 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : (i) 100x10 mm |
| 193 | Providing and fixing bright finished 100mm mortice lock with 6 levers without pair of handles for aluminium door with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge. |
| 194 | (O) SUB-HEAD : CLADING WORK |
| 195 | Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc.complete at all levels: |
| 196 | (i) 14 mm thick Rajnagar Plain white marble/ Udaipur green marble/ Zebra black marble or equivalent duly approved: - Area of slab upto 0.50 sqm: |
| 197 | (ii) 14 mm thick Rajnagar Plain white marble/ Udaipur green marble/ Zebra black marble or equivalent duly approved: - Area of slab over 0.50 sqm. |
| 198 | (iii)14 mm thick Granite of any colour and shade duly approved - Area of slab upto 0.50 sqm. |
| 199 | (iv)14 mm thick Granite of any colour and shade duly approved - Area of slab over 0.50 sqm. |
| 200 | (P) SUB-HEAD : BRICK WORK |
| 201 | First class brick work in foundation and plinth including cost of all materials as required complete:In cement mortar 1:4 (1 cement : 4 fine sand ). |
| 202 | (Q) SUB-HEAD : EARTH WORK |
| 203 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. - - All kinds of soil |
| 204 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 205 | (R) SUB-HEAD : CEMENT CONCRETE WORK |
| 206 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level: (i) 1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size |
| 207 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
