Supplying And Fixing Of Workstation Tables For Main Office Room In P.G Department Of Electronics And Instrumentation Technology At Main Campus. Supplying And Fixing Of Workstation Tables For Main Office Room In P.G Department Of Electronics And Instrument, Main Campus-Jammu And Kashmir

Supplying And Fixing Of Workstation Tables For Main Office Room In P.G Department Of Electronics And Instrumentation Technology At Main Campus. Supplying And Fixing Of Workstation Tables For Main Office Room In P.G Department Of Electronics And Instrumentation Technology At Main Campus. , Table Top: The Workstationtop Shall Be Made Of 25Mm Thick Prelaminated Particle Board ( As Per Is: 12823 ) . Bottom Of The Worktop Shall Have A Backing Laminate Of Minimum 0.6Mm Thickness. All The Edges Of Work Surface Shall Be Provided With Machine Pressed 2 Mm Thick Pvc Edge Band Glued With Hotmelt Eva Glueto Maintain Softness And Flexibility, Clarity And Gloss, Barrier Properties, Low-Temperature Toughness, And Resistance To Uv Radiation. The Worktop Should Be Supported By A Worksurface Bracket Made Up Of 2.0 Mm Thick Crca Grade D Steel As Per Is : 513-19. Table Top Dimension Shall Be 1350X925mm. Partition Systems:- Providing And Fixing Of Panel Based System Of 50-60 Mm Thick Of 1200Mm Height With Front Glass Panel. The Side Panel Should Comprise Of Vertical And Horizontal Extrusions Of Aluminumhaving Material Al96063-T6 And Shouldhave Average Wall Thickness Of 1.2 Mm & Powder Coated With Epoxy-Polyester Powder With Average 50 To 60 Micron Thickness. Bottom Frame For Panel Should Comprise Of L- Channels Made Of 2Mm Thick Crca Steel ( Is:513 ) , Formed Plates Of 3Mm Thick Hr Steel ( Is:2062 ) & Erw Steel Tube Of Size 35X15x1.6Mm In Oval Cross Section ( Is:7138 ) Welded Together. The Same Shall Have Tobe Bolted To The Uprights With Suitable Screws.The Panel Should Be Supported On Legs 120-130Mm High Fabricated Out Of Ms Tube Of Section Of Size Between 30 To 40Mm Of Minimum Thickness Of 1.5Mm ( Is: 7138 Erw Tube ) With The Base Plate Of The Ms Plate As Per Tube Size Over Which A Leveler Shall Be Fitted, Which Allows For Adjustment Of The Height Upto 50Mm. The Top And End Trims Should Be Powder Coated Aluminium Slide Fitted With The Help Of End Trim Connectors. All 2 Way, 3 Way And 4 Ways Junction To Be Covered With Die Cast Aluminum Caps Having Material Al96063-T6 And Shouldhave Average Wall Thickness Of 1.2 Mm. Wire Management : The Cables Shall Come From Ground In A Concealed Conduit / Raceway . System Offered Should Have Provision To Provide The Switch Cut Outs On The Top Tile Above The Worktop Or On The Bottom Tile Of The Panel. Blocks : Theblock For Panel’Sshall Comprise Of 35-40 Mm Thick Paper Honeycomb Or Any Other Filler For Compressed Strength With 3-6Mm Mdf On Each Sides And 0.6Mm Decorative Laminate Or Fabric On Both Sides. Particle Board Framing Shall Be Used On Outer Boundary Of These Blocks As Well As Intermediately At Certain Locations Forming Conduit For Passing Cables. The Blocks Should Be Fixed Into The Supporting Frame Befor Fixing Of The Horizontal And Vertical Trims Which Should Not Be Used As Structural Members.The Top Panels Should Be Offered In Fabric , Fabric Tackable , Metal, White Board . Fabric Shall Be Upholtered With Zero Voc Content Glue As Per Drawing With Fabric Of Approved Quality. White Board Tiles Shall Be Made Of 8.0 Mm Thick Particle Board Conforming To Is: 12823 Laminated With 0.6Mm Thick White Glossy High Pressure Laminate On Outer Side With 0.6Mm Backing Laminate On Inner Surface And Will Behaving All Its Edges With Minimum 0.5 Mm Thick Pvc Edging.The Panel Between 2 Adjacent Seats Shall Be Made Up Of 20-30Mm Thickness. These Intermediate Panels Shall Be Offered In Fabric , Fabric Tackable , Metal Or As Desired By Engineer - In - Charge.The Bottom Panel Shall Be Metal With Provision Of Passing Cables And Cutouts For Switch Boxes At Suitable Locations To The Satisfaction Of The Engineer - In - Charge. Pedestal : The Pedestal Should Be Fixed With Screws To The Worktop Bottom Through Top Stiffners.The Leg Assembly Should Be Fabricated By Co2 Welding Vertical Ms Tubes Of Section 38Mm X 25Mm ( Is 7138 Erw Tube, 38 Mm X 25 Mm X 16 Bg ) Inside Which Leveler Holder Plates Of Size 34 X 21 X 5 Mm ( Is :2062, 5 Mm Hr ) Are Welded With Horizontal Bottom Channel Made Of 2.0 Mm Thick M.S Crca Grade D As Per Is 513. The Height Of The Pedestal Should Be600mm Without Leg Assembly And 720 Mm Including Leg Assembly. Cpu Trolley : Metal Cpu Trolley To Be Provided For Each User Made Of 0.7Mm Crca Sheet Duly Powdercoated With 50Mm Microns Having Adjustable Sides And Nylon Lockable Castors. Key Board Tray : Metal Powder Coated Key Board Tray To Be Provided For Each User Made Of 0.7Mm Crca Sheet Duly Powdercoated With 50Mm Microns With Telescopic Channels.The Product Quoted Should Be Iaq / Greenpro / Bifma Level 3 Certified. Godrej / Wipro / Monarch Or Equivalent

INR 300 /-

Refer document

INR 2.70 Lakhs /-