Renovation Of 06 Nos Type-Ii Qtr Renovation Of 06 Nos Type-Ii Qtr Qtr No-20-21, 25-26, 29-30 For Education Department At Oralkatcha, Baratang Re-Call
Tender Value
32.79 Lakhs
Estimated cost
Bid Submission
02 Oct 2021
0 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Baratang → Andaman And Nicobar Islands
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Renovation Of 06 Nos Type-Ii Qtr Renovation Of 06 Nos Type-Ii Qtr Qtr No-20-21, 25-26, 29-30 For Education Department At Oralkatcha, Baratang Re-Call
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 5 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 6 | Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required Centering complete. |
| 7 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20mm nominal size). |
| 8 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 9 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 10 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : |
| 12 | Foundations, footings, bases of columns, etc. for mass concrete |
| 13 | Suspended floors, roofs, landings, balconies and access platform |
| 14 | Shelves (Cast in situ) |
| 15 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 16 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 17 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 18 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 19 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 20 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer- in-charge |
| 21 | Extruded section profile size 42x50 mm |
| 22 | Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm, painted with primer , all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5 mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100 mm x 8 mm complete as per manufacturer\"s specifications and direction of Engineer-in-charge. |
| 23 | Non decorative finish |
| 24 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 25 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 26 | Electric resistance or induction butt welded tubes |
| 27 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 28 | Providing and fixing bolts including nuts and washers complete. |
| 29 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 30 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 31 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 32 | 6 mm thick Cement fiber board as per IS: 14862 |
| 33 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 34 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 35 | Ridges plain (500 - 600mm) |
| 36 | 12 mm cement plaster of mix : |
| 37 | 1:4 (1 cement: 4 fine sand) |
| 38 | White washing with lime to give an even shade : |
| 39 | New work (three or more coats) |
| 40 | Distempering with 1st quality acrylic distemper (ready mixed) of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. |
| 41 | Two or more coats on new work |
| 42 | Finishing walls with water proofing cement paint of required shade : |
| 43 | New work (Two or more coats applied @ 3.84 kg/10 sqm) |
| 44 | Applying priming coat: |
| 45 | With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 46 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 47 | Two or more coats on new work |
| 48 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 49 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 50 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 51 | Of area 3 sq. metres and below |
| 52 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : |
| 53 | Of sectional area 40 square centimetres and above |
| 54 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: |
| 55 | Asbestos sheet |
| 56 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 57 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 58 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. INTERNAL WORK - EXPOSED ON WALL |
| 59 | 15 mm dia nominal bore |
| 60 | 25 mm dia nominal bore |
| 61 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work |
| 62 | 15 mm dia nominal bore |
| 63 | 25 mm dia nominal bore |
| 64 | 40 mm dia nominal bore |
| 65 | Providing and fixing brass bib cock of approved quality : |
| 66 | 15 mm nominal bore |
| 67 | Providing and fixing brass stop cock of approved quality : |
| 68 | 15 mm nominal bore |
| 69 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 70 | 25 mm nominal bore |
| 71 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 72 | Circular tank |
| 73 | Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge. |
| 74 | Providing and laying hollow cement concrete block walling upto floor five level 100 mm thick consisting of hollow block of size 400x100x200 mmthick of mix 1:3:6 (1 Cement:3 Coarse sand:6 graded stone aggregate 12.5 mm nominal size) laid in cement mortar 1:6 (1 Cement: 6 Coarse sand). |
| 75 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position: |
| 76 | Superior hard wood of cat-II (A). |
| 77 | Providing and fixing in position eaves or facia board with 19 mm thick marine ply wood (BWR) conforming to IS:710 30 cm wide including fixing with nuts and bolts etc. (Make: Century/Green ply or equivalent) complete. |
| 78 | Providing and fixing 35 mm thick glazed shutters for windows with superior hard wood cat-II (A) as per IS: 401 using 7.5 Kg/sqm (4 mm thick) glass panes including oxidised M.S. butt hinges with necessary screws etc., complete as per the directed by Engineer-in-charge. |
| 79 | Providing and fixing 35 mm thick panelled, glazed or panelled and glazed shutters for doors i/c oxidised MS butt hinges with necessary screws with superior hard wood cat-II (A) as per IS: 401 i/c panelled with 12 mm thick marine ply (BWR) conforming to relevant specification with wooden cleats and blocks as per the directed by Engineer-in-charge. |
| 80 | Providing cement concrete surface drainwith 1:3:6 ( 1 cement: 3 sand: 6 graded stone aggregate 40 mm nominal size) finished with 1:4 (1 cement: 4 fine sand) including a floating coat of neatcement inside the drain and its top and exposed surface including earth work in excavation and disposed of surplus earth. |
| 81 | 15 x 15 cm surface drain |
AI Tender Summary
Tender Timeline
Sep 11, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedOct 02, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 04, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender