Construction Of G Plus 3 16 L.S. Quarter ( Block- 8 ) At Cts, Musabani In The District Of East Singhbhum. Construction Of G Plus 3 16 L.S. Quarter ( Block- 8 ) At Cts, Musabani In The District Of East Singhbhum.
Tender Value
3.35 Crore
Estimated cost
Bid Submission
15 Sep 2021
0 days left
EMD
3.36 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Musabani → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of G Plus 3 16 L.S. Quarter ( Block- 8 ) At Cts, Musabani In The District Of East Singhbhum. Construction Of G Plus 3 16 L.S. Quarter ( Block- 8 ) At Cts, Musabani In The District Of East Singhbhum.
BOQ
| Sl. No. | Item Description |
| 1 | Building work |
| 2 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 3 | Extra for earthwork in hard soil as per specification and direction of E/I. ( Vide classificationofsoil iten _B) |
| 4 | Filling infoundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earthobtainedfrom excavation offoundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. |
| 5 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 6 | Providing designation 75A brick work in CM (1:6) in Foundation and plinth with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 7 | Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 8 | Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. |
| 9 | Supplying, fitting & fixing 30mm thick solid core type decorative Single leaf flush shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes allcomplete as per building specification and direction of E/I. |
| 10 | Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold ofmild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, includingM.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steelprimer after pre-treatment of the surface as directed by Engineerin-charge Fixing with adjustable lugs with split end tail to each jamb |
| 11 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 12 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Polyester powder coated aluminium(minimum thickness of polyester powdercoating 50 micron) |
| 13 | Extra for Brick work for each consecutive floor above first floor including watering and scaffolding all complete as per direction of E/I |
| 14 | For 10\" th. B/W. |
| 15 | A. Second Floor |
| 16 | B. ThirdFloor |
| 17 | For 5\" th B/W. |
| 18 | A. Second Floor |
| 19 | B. ThirdFloor |
| 20 | Providing P.C.C.M100 in normal mix of(1:3:6) in foundation with approved quality of stone metal grade III (50mm to 25mm size) clean coarse sand to F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I |
| 21 | Providing R.C.C.M 200 with nominal mix of(1:1.5: 3) in foundation and plinth with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing( but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and directionof E/I |
| 22 | Centering and shuttering including strutting, propping etc. and removal of form forCentering and shuttering including strutting, propping etc. and removal of form for |
| 23 | Providing R.C.C.M - 200 in band at plinth level with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l. |
| 24 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 25 | Providing R.C.C.M 200 with nominal mix of (1: 1.5: 3) in lintelwith approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and directionof E/I |
| 26 | Centering and shuttering including strutting, propping etc. and removal of form forSmall lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 27 | Providing R.C.C.M 200 with nominal mix of (1: 1.5: 3) in roof slab with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, (but excluding the cosat of reinforcement) taxes and royalty all complete as per building specification and directionof E/I |
| 28 | Centering and shuttering including strutting, propping etc. and removal of form forSuspended floors, roofs, landings, balconies and access platform |
| 29 | Providing R.C.C.M 200with nominal mix of (1:1.5: 3) in beam of all types with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing,( but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and directionof E/I |
| 30 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 31 | Providing R.C.C.M 200with nominal mix of (1:1.5: 3) in columns with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing,( but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and directionof E/I |
| 32 | Centering and shuttering including strutting, propping etc. and removal of form forColumns, Pillars, Piers, Abutments, Posts and Struts |
| 33 | Providing Av. 63 MM thk M200 With nominal mix in Chajja..(1:1.5:3) Chajja with apporoved quality ofstone chips 20 mm to 6 mm size graded and cleane coarse sand of FM. 2.5 to 3 including making drips course in concrete , sereening centering shuttring and mixing cement concrete in mixer and placing in posotion vibrating striking 6 mm cemet plaster 1:4 in ceiling and side of chajja with sand of FM. 1.5 curing (but excluding the cost of reinforcement ) taxes and royalty sll complere as per building specefication and direction of E/I |
| 34 | Centering and shuttering including strutting, propping etc. and removal of form forWeather shade, Chajjas, corbels etc., including edges |
| 35 | Providing 35mm thick precast R.C.C M-200 with with nominal mix of (1:1.5:3) shelves with apporoved quality of stone chips 12 mm to 6 mm size graded and cleane coarce sand of FM 2.5 to 3 with 1.5 mm cement punning at top and side and 6 mm cement plaster (1:4) at bottom including screening curing and placing the slab in in position taxes and royalty all complete as per building specefication and direction of E/I |
| 36 | Centering and shuttering including strutting, propping etc. and removal of form for4Shelves (Cast in situ) |
| 37 | Providing R.C.C.M 200 with normal mix of (1:1.5: 3) in stair case with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and directionof E/I |
| 38 | Centering and shuttering including strutting, propping etc. and removal of form forStairs, (excluding landings) except spiral-staircases |
| 39 | Providing reinforcement (Round bars confirming to I.S. 432 dia In mm (I.S. 2062 Gr A) of 6 &8 mm. dia rods as per approved design and drawing excluding carriage of bars to work site, cutting, bending, and binding with annealed wire with cost of wire, removal of rust, placing the rods on position all complete as per building specification and direction of E/I.(i) 6 mm dia Gr. A(Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 40 | Providing Tor steel reinforcement of 8 mm dia rods as perapproved design and drawing excluding carriage of bars to work site cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per builing specification and direction of E/I. (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 41 | Providing Tor Steelreinforcementof 10mm , 12 mm & 16 mm dia bars as perapproved design and drawing excluding carriage ofbars to work site, cutting bending and bindingwith annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specificationand direction of E/I |
| 42 | (a) 10 mm (TMT coil Fe 500)(Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 43 | (b) 12 mm (TMT coil Fe 500) (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 44 | (c) 16 mm (TMT coil Fe 500) (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 45 | Providing Tor Steelreinforcementof 20mm, 25 mm, 28mm, 32mm dia bars as per approved design and drawingexcluding carriage ofM.S. bars of work site, cutting, bending and bindingwith annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specificationand direction of E/I |
| 46 | (a) 20 mm ,25mm, 28mm& 32 mm TMT bar FE 500 (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 47 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement:3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. |
| 48 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). |
| 49 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 50 | Providing and fixing 1mm thick PVC rigid foam sheet over w.c.\"s door shutter using synthetic rubber based adhesive (Fevicol SR 998 or equivalent). |
| 51 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 52 | Over Internal & External Surface |
| 53 | ProvidingP.C.C.M200 in normal mix of(1:1.5:3) in foundation with approved quality of stonechips 20mm to 6 mm size graded and clean coarse sand to F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 54 | Providing& supplyingCico liquid / impermo water proofing compound in cement concrete or cement mortar @2% of cement quqntity by weight ( as specified)for water proofing, including all carraige and taxes . |
| 55 | Providing & laying water proofing treatmentin sunken portion of WCs, abathrooms etc. by applying cement slurru mixed with Armourcrete of M/S The Structural Water Proofing Company PVT. Ltd.or Tapecrete of M/s CICO Engg. Servce consisting of applying : |
| 56 | (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with Armourcrete or Tapecrete @0.125 kg/ sq.m. This layer will be allowed to air cure for 4 hours |
| 57 | (b)second layer of slurry of cement @ 0.242 kg/sqm mixed with Armourcrete or Tapecrete @0.126 kg/ sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. |
| 58 | The rate includes preperation of surface, treatment& sealing of all joints, corners, junctions of pipes & masonary with polymer mixed slurry. |
| 59 | Providing 150 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 125 mm apron including cost of earthwork involved with 75m cement concrete (1:4:3) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I. |
| 60 | Providing 250 mm wide brick drain in cement mortar (1: 6) with av. 150 mm. clean depth and 250 mm apron including cost of earthwork involved with 75 mm, cement concrete (1: 4: 3) over one brick designation 75A, flat soling in proper grade and slope at the base, the drain duly plastered in C.M (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 61 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 62 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. |
| 63 | Shoe 110 mm |
| 64 | Coupler 110 mm |
| 65 | Bend 110 mm |
| 66 | Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flats as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, hoisting carriage of grill to work site, hoisting as per building specification and direction of E/I. |
| 67 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50 x 20 mm |
| 68 | Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 69 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). |
| 70 | Light shade pigment using white cement |
| 71 | Providing 12mm thickcement plaster (1:6) with clean coarse sand of F.M 1.5 on inside wallincluding screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I |
| 72 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scafolding taxes and royalty all complete as per buildings specification and direction of E/I. |
| 73 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm |
| 74 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 75 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : |
| 76 | Udaipur green marble |
| 77 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 78 | Extra for plaster work over exteriour surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/I |
| 79 | A. Second Floor |
| 80 | B. ThirdFloor |
| 81 | Making 6x6 mm Groove in plaster surface over walls trullyhorizantal andvertical as specified as regularinterval , at all heights including claening finishingscaffoolding and curing with all leads and lifts ofwater all complete as per buildingspecification and direction of E/I. |
| 82 | Extra for FLOORINGwork for each consecutive floor above first floorincluding wateringand scaffolding, all complete as per direction of E/I. |
| 83 | A. Second Floor |
| 84 | B. ThirdFloor |
| 85 | Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm overand including priming coat of exterior primer applied @ 2.20kg/ 10 sqm) |
| 86 | Providing two coats of oil bound distemper of approvedmake & shadeover a coat of cement primerovernewsurface including preparing the plastered surface by rubbing, smooth with pumic stone or fine sand paper, aplying putty wherever required,scaffolding , washing of flores and taxes etc. all complete as per building specification direction of E/I. |
| 87 | Providing two coats of synthetic enamel paint of approved shad and make over new wooden surface including cleaning the surface after removing dirt sccales smokes grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 88 | Providing two coats of synthetic enamel paint of approved shade and made over steel surface including cleaning the surface thoroughly including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I |
| 89 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 90 | (a) Bricks |
| 91 | (b) Local Sand |
| 92 | (c) Coarse Sand |
| 93 | (d) Stone Chips |
| 94 | (e) Cement |
| 95 | (f) Steel |
| 96 | Section - II Water supply and sanitary installation works |
| 97 | Supplying, Fitting and Fixing vitreous white Glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. apporoved make with 100mm H.C.I \"p\" trape 15 liters C.I pull and let go flushing cisternof names or other I.S.S. equivalent make complete with all fittings, C.I. or C. C. brackets 32 mm alkathene/P.V.C. telescopic flush pipe anout 2 M long with one bragg couping and clamps G.I chain and pull including supplying and fixing a pair of vitreous whotr glazed earthenware ware footrest to be fixed in floor 15mm C.I body brass spindle stope cock weight not less then 50 grms, 15mm P.V.C. conection pipe 150 mm long and exposed pipe and cistern with two coates of apporoved paint over a coat of red oxide etc. all complete as per specification and direction of E/I. (A)580 mm long (C) with12.5 lit. low level PVC cistern. |
| 98 | Supplying fitting and fixing 40mm high vitreous white glazed earthen E.W.C with ‘p’ trap of parry Hindustan or any other approved I.S.S. Make including supplying and fixing 15 liters C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S or bracket with telescopic flush pipe with brass couping and plumbers joints spindle stop cock of apporoved quality weight not less then 150 grams 15mm P.V.C. alkathene pipe 15 cm long wiyh brass couping at both ends and white plastic solid state seal and lead of commander / cucroo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of apporoved paint over a coat of red oxide primiing all complete as per specification and direction of E/I. (i) with \"P\" trap (b) 12.50 lit low level PVCcistern. |
| 99 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore |
| 100 | Providing and fixing C.P.brass long nose bib cock of approved quality conforming to standard and weight not less thain 810gms. 15mm nominal bore approved brand C.P. fittings |
| 101 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 15 mm nominal bore |
| 102 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 103 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931(a) 15mm nominal bore |
| 104 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour 15 mm nominal bore, weighing not less than 32 gms |
| 105 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end ) |
| 106 | 25MM nominal bore |
| 107 | 32MM nominal bore. |
| 108 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape : Rectangular shape -453 X357 mm |
| 109 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:Falt back wash basin size550x400mm with single 15mm pillar tap |
| 110 | Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole |
| 111 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.15 mm nominal bore with 45 cm length |
| 112 | Providing And fixing 32 mm waste pipe for sink or wash basin including P.V.C. waste fittings complete.32 mm dia |
| 113 | Providing and fixing on wall face unplasticised Rigidpipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 114 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVCpipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 115 | PVC Door Tee 110mm diaSINGLE JUNCTION ( Supreme ) |
| 116 | PVC Plain Bend 110mm dia ( Supreme ) |
| 117 | PVC Door Bend 110mm dia( Supreme ) |
| 118 | 110mm diaPVC cowel( Supreme ) |
| 119 | Plain trap110mm dia( Supreme ) |
| 120 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 121 | 15 mm nominal outer dia Pipes |
| 122 | 20 mm nominal outer dia Pipes |
| 123 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge.External work |
| 124 | 25 mm nominal outer dia Pipes |
| 125 | 32 mm nominal outer dia Pipes |
| 126 | 40 mm nominal outer dia Pipes |
| 127 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 128 | Supllying and matarials with lobour for construction inspection chamber of designation class 75b brick deep 600x450 internal diamention having 250mm wall thickness in cementmorter(1:6)including 12mm cement plaster (1:4)with punning on inside and cement plaster (1:6)with 600x450mm G.I. cover with frame (weight not less than 36k.g)in foundation and refilling all complete as per specification and direction of E/I. |
| 129 | Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete. 150 MM dia R.C.C. pipe |
| 130 | Providing and fixing stainless steel A ISI 304(18/8) kitchen sink as per I.S.13983 with C.I. Brackets stainless steel plug 40mm including painting of fittings and brackets cutting and making goods the walls wherever required:600x450x200mm |
| 131 | Providing and fixing PTMT/ C.P. swivelling shower,15mm nominal size, 95mm long, 65mm dia. of approved quality, color & make weighing not less than 40 gms with approximate 80 holes of 1.2 mm dia. |
| 132 | SectionIII 200x150xmm dia Deep bore Well With Pump set & electrification etc works. |
| 133 | Suppling all materisls labour and tools and cost of drilling 200mm x 165mm bore well in all kinds of soil and rock in rural area for installation of pump set with hydrolic DTH rig machine, all complete including suplying all materials tools, drilling rig, Air compressor and equipments, as well as fuel, lubricants and cost of transprtation of Rig machine and other vehicles up to the site. |
| 134 | a) From 0.0M to 50.0 M belew G.L |
| 135 | b) From 51.0 M to200.00 M belew G.L |
| 136 | supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe itc including all taxes, VAT, Excise duty, freight charges with inspection charges etc as applicable, etc all complete job. |
| 137 | Cleaning Flushing and devloping of drilled hole for testing the discharge of water development of bore well by continueous flow of water bu using heavy compresser upto satisfaction of E/I. To get uniterrupted flow of water free from sand and soil etc. |
| 138 | Supplying and fitting M.S cap over 200mm dia casing pipe as per direction of E/IFor safety of drilling bore including providing of guard for safety of the same till returned final. |
| 139 | Supplying 100 mm dia submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump. |
| 140 | Submersible Pump 150 mm dia ( with Bronze impeller) up to 8 stages 2.0 HP |
| 141 | Supplying complete panel board with all accessories ( starter 1 no, volt meter 1 no, amp meter 1 no,100 amp kit kat ( male & female) all complete job. |
| 142 | Supplying 3 core flat flexible submersible cable with, copper conductor, PVC insulated and PVC sheathed.3 Core 4mm thick |
| 143 | 2no heavy duty clamp 40mm dia suitable for 200 mm dia pipe with all complete job. |
| 144 | Supplying & lowering 40mm da column G. I. pipe with all complete job. |
| 145 | Section - IV Septic tank & Soak pit ( 2 nos) |
| 146 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 147 | Extra for earthwork in hard soil as per specification and direction of E/I. ( Vide classificationofsoil iten _B) |
| 148 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 149 | Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 150 | Providing P.C.C.M150 in normal mix of(1:2:4) in foundation with approved quality of stone chips 20 mm 6 mm size graded and clean coarse sand ofF.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I |
| 151 | Providing R.C.C.M 200 nominal mix of(1:1.5: 3) in beam of all types with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing,( but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and directionof E/I |
| 152 | Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. |
| 153 | Providing Precast R.C.C.M - 200 with nominal mix of (1:2:4) slab of desired size withapproved quality of stone chips and clean coarse sand of F.M. 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement ) taxes and royalty , all complete as per building specification and direction of E/I. |
| 154 | Providing designation 75A brick work inC.M (1:4) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 155 | Providing 12mm thick cement plaster (1:3) with clean coarse sand ofF.M. 1.5 approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as perbuilding specification and direction of E/I. |
| 156 | Providing 1.5 mm thick cement punning including curing, carriage of water with all leads and lifts of water as perbuilding specification and direction of E/I. |
| 157 | Providing and laying brick bats in soakpit with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. |
| 158 | Supplying, fitting and fixing C.I. cover with frame for mane hole and inspection chamber with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of E/I. (a) Size 600 x 450 mm (Wt. 25 Kg). |
| 159 | Providing Tor steel reinforcement of 8 mm dia rods as perapproved design and drawing excluding carriage of bars to work site cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per builing specification and direction of E/I.(Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 160 | Providing Tor Steelreinforcementof 10mm , 12 mm & 16 mm dia bars as perapproved design and drawing excluding carriage ofbars to work site, cutting bending and bindingwith annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specificationand direction of E/I |
| 161 | 10 mm (TMT coil Fe 500) ((Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 162 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 163 | (a) Bricks |
| 164 | (b) Local Sand |
| 165 | (c) Coarse Sand |
| 166 | (d) Stone Chips |
| 167 | (e) Cement |
| 168 | (f) Steel |
| 169 | Section VI -APPROACH ROAD |
| 170 | ProvidingP.C.C.M200 in normal mix of(1:1.5:3) in foundation with approved quality of stonechips 20mm to 6 mm size graded and clean coarse sand to F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 171 | Embanjkmenr\t construction with material obtained from Borrow Pits (Construction of embanlment with approved material obtained from borrow pits with all lifts and leads transporting to site, spreding , grading to required slope and compacting to meet requirement of table 300-2) |
| 172 | (i) Rolling with vibratory roller |
| 173 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 174 | Providing designation 75A one brick edge soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 175 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 176 | (a) Bricks |
| 177 | (b) Local Sand |
| 178 | (c) Coarse Sand |
| 179 | (d) Stone Chips |
| 180 | (e) Cement |
| 181 | LAND DEVELOPMENT (INCLUDING TOE WALL) |
| 182 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 183 | Extra for earthwork in hard soil as per specification and direction of E/I. ( Vide classificationofsoil iten _B) |
| 184 | Filling in foundation trenches and plinth layers not exceeding 150 mm thick well watered rammed fully compacted and fine dressed withearth obtained after cutting with in a lead of 50M and lift of 1.5M all complete as per building specification and directionof E/I ( Mode of measurement compacted volume) |
| 185 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 186 | Providing designation 75A brick work in CM (1:6) in Foundation and plinth with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 187 | Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 188 | Providing P.C.C.M150 in normal mix of(1:2:4) in foundation with approved quality of stone chips 20 mm 6 mm size graded and clean coarse sand ofF.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I |
| 189 | Providing 12mm thick cement plaster (1:3) with clean coarse sand ofF.M. 1.5 approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as perbuilding specification and direction of E/I. |
| 190 | Providing 1.5 mm thick cement punning including curing, carriage of water with all leads and lifts of water as perbuilding specification and direction of E/I. |
| 191 | Providing 12mm thickcement plaster (1:6) with clean coarse sand of F.M 1.5 on inside wallincluding screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I |
| 192 | Filling infoundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earthobtainedfrom excavation offoundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. |
| 193 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 194 | (a) Bricks |
| 195 | (b) Local Sand |
| 196 | (c) Coarse Sand |
| 197 | (d) Stone Chips |
| 198 | (e) Cement |
| 199 | (f) Earth |
| 200 | Rain Water Harvesting |
| 201 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 202 | Extra for earthwork in hard soil as per specification and direction of E/I. ( Vide classificationofsoil iten _B) |
| 203 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 204 | Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 205 | Providing P.C.C.M150 in normal mix of(1:2:4) in foundation with approved quality of stone chips 20 mm 6 mm size graded and clean coarse sand ofF.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I |
| 206 | Providing designation 75A brick work in CM (1:6) in Foundation and plinth with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 207 | Stone Metal at quarry site .. Traxes and royalty all complete as per building specification and direction of E/I.0.90 m Gravel filling |
| 208 | 0.90 M stone Boulder filling |
| 209 | Providing precast R.C.C.M -200 with nominal mix.of (1:1.5:3) slab of desired size with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering, carrying the slab manually to site and laying in position, (but excluding the cosat of reinforcement) taxes and royalty all complete as per building specification and directionof E/I |
| 210 | Providing 12mm thick cement plaster (1:3) with clean coarse sand ofF.M. 1.5 approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as perbuilding specification and direction of E/I. |
| 211 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scafolding taxes and royalty all complete as per buildings specification and direction of E/I. |
| 212 | Providing Tor steel reinforcement of 8 mm dia rods as perapproved design and drawing excluding carriage of bars to work site cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per builing specification and direction of E/I.(Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 213 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 214 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. |
| 215 | 110 mm bend |
| 216 | Shoe 110 mm |
| 217 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand)and making good the wall etc. complete(110 mm ) |
| 218 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 219 | (a) Bricks |
| 220 | (b) Local Sand |
| 221 | (c) Coarse Sand |
| 222 | (d) Stone Chips |
| 223 | (d) Cement |
| 224 | 115/125 mm dia drilled Tube Well for drilling in all kinda of Soil and rock for installation o hand pump with DI rings all complete including supplyin all materials, labours , tools drilling rigs air compressor and equipments s well as fuel li\ubricant for making115/125 mm dia boring etc and cost of transporting rigmachine and other vechile up to site of work including contrctor profit & OH chares as per specification and directtion of Engineer Incharge fo the year 2015-16. |
| 225 | Drilling upto 30 M depth below G.L in Rulararea |
| 226 | Drillingbeyond 31 mtr upto 55 mtr below GL in Ruralarea |
| 227 | 32 mm UPVC pipe 125 mm dia conforming o IS: latest version: |
| 228 | S/M/L forF/f wire mesh pipe |
| 229 | Electrical Work |
| 230 | Note:- OF MAKE (1)PVC insuleted copper conductor wire of make:-Havell\"s/Polycab/Finolex (2)PVC conduit of thiknss 1.5mm/2mm for wiring:-Polycab/ANCHOR/AKG (3) GI modular box of make -: Anchor/ Havells/Legrand/ABB (4)Switches/soket outlet for modular type:- Anchor (roma)/Havells(cabtree)/Legrand/Schneider (5)MCCB,MCB,SFU,CHANGEOVER,RCCB,MCB-DB:-Havell\"s/L&T/Legrand/Schneider (6)XLPE/PVC aramoured cable:-Havell\"s/Polycab/V-guard (7) LED ITTING FIXTURE -: Havells/Bajaj/Crompton (Model/as per E/I ) (8) CEALING / WALL / EXHAUST FAN -: Havells / Bajaj / Usha / Crompton (Model/as per E/I ) (9)OCTAGONAL POLE-: Bajaj/Philips/Surya (10) CHEMICAL EARTHING OF MAKE - TRUEPOWER EARTHING (11) CENTRALISED AIR CONDITIONING OF MAKE - VOLTAS/MITSHUBISHI/ TOSHIBA/DAIKIN (12)ALL ELECTRICAL WIRING WORK SHOULD BE CONCEALED |
| 231 | Point wiring in PVC conduit, with modular type switch:-Wiring for light point/fan point/exhaust fan point/call bell point with 1.5. sq.mm FR PVC Insuleted copper conductor single core cable in recessed PVC conduit, with modular type switch, pheonlic lamineted sheet,suitable size G.I.box etc. |
| 232 | Group A |
| 233 | Twin control point wiring PVC conduit with modular type switch:-wiring for Twin control point with 1.5 sq mm FR PVCInsuleted copper conductor single core cable in recessed PVC conduit, 2 way modular, switch, pheonlic lamineted sheet,suitable size G.I.box etc.as required. |
| 234 | Power plug wiring in PVC conduit(2x4 sq mm) :- Wiring for light/Power plug with 2x4 sq mm FR PVC insuleted copper conductor single core cable in recess PVC conduit along with 1 Nos. 4 sq mm FR PVC insuleted copper conductor single core cable for loop earthing as required. |
| 235 | Circuit/submain wiring in PVC conduit:-Wiring for circuit/submain wiring along with earth wire with the following size PVC insuleted copper conductor single core cable in recessed PVC conduit as required |
| 236 | 2x1.5 sq mm+1x1.5 sq mm earth wire |
| 237 | 2x2.5 sq mm+1x2.5 sq mm earth wire (for LED building outar light) |
| 238 | 2x2.5 sq mm+1x2.5 sq mm earth wire |
| 239 | 2x6 sq mm+1x6 sq mm earth wire |
| 240 | 2x10 sq mm+1x6 sq mm earth wire |
| 241 | TV cable in existing conduit :- Supplying and drawing co-axial TV cable RG-6 grade copper conductor,PE insulated,withPVC sheath in the existing recessed PVC conduit as required. |
| 242 | S/F PVC conduit :-supplying and fixing of following sizes PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case recessed conduit as required . |
| 243 | 20mm |
| 244 | S/F PVC/G.I. boxes :- Supplying and fixing PVC/G.I. box of following sizes on surface or in recess with suitable size of phenolic laminated sheet cover infront including painting etc as required . |
| 245 | 75mm x 75mm x 50mm deep/ (4\" x 4\") |
| 246 | S/F modular type switch /socket :- Supplying and fixing following modular type switch box/cover including connections but excluding modular plate etc as required |
| 247 | 5/6 amps, one way switch |
| 248 | 5/6 amps, socket |
| 249 | 15/16 amps, one way switch |
| 250 | TV socket socket outlet |
| 251 | S/F Modular type electronic fan regulator:-Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connectionons but excluding modular plate etc, as required. |
| 252 | S/F Modular boxes, base & covre plate:-following size/ modular G.I box along with modular base & cover plate for modular switches in recess etc, as required. |
| 253 | 1 or 2 module(78mm x 78mm x 45mm) |
| 254 | 6 module(78mm x 205mm x 50mm) |
| 255 | S/F light plug point with modular type accessories:- Supplying and fixing suitable size G.I.box with modular plate and coverin front on recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switchconection painting etc, as required. |
| 256 | S/F power plug point with modular type accessories:- Supplying and fixing suitable size G.I.box with modular plate and coverin front on recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switchconection painting etc, as required. |
| 257 | S/F ceiling rose:-Supplying and fixing 2 pin 5 amp, ceiling rose on the existing junction box/wooden block including connection etc as required. |
| 258 | S/F Batten holder:-Supplying and fixing batten/angle holder including connection etc, as required. |
| 259 | S/F Dingdong Call bell :-Supplying and fixing dingdong call bell suitable for DC/AC single phase,230 volt, complete as required. |
| 260 | Errection on incandescent light fitting:-Errection of wall bracket/ceiling fitting, complete with all accessories including connection etc as required. |
| 261 | ITC fluorescent fitting directly on surface:-Instaliation, testing and commissioning of prewired, fluorescent fitting of all types, complete with all accessosries and tube etc. directly on ceiling /wall including connection with 1.5 sq mm.FR PVC insulated, copper conductor. |
| 262 | ITC ceiling fan:-Instaliation, testing and commissioning of ceiling fan including wiring the down rod of standard length( uptwo 30 cm) with 1.5 sq mm.FR PVC insulated copper conductor, single core cable etc as required |
| 263 | S/F S.P. MCB DB:-Supplying and fixing following way single pole nutral,sheet,MCB distribution board,240 volt,in recess,complete with tinned copper busbar,earth bar, din bar, detachable gland plate, interconnections, phosphatized and power painted including earthing etc. as required.(But without MCB/RCCB/ISOLATOR) |
| 264 | 8 Way,Double door |
| 265 | S/F \"B\" series. S.P.MCB:-Supplying and fixing 6 amps to 32 amps rating,240 volts, \"B\" series miniature circuit breaker suitable for lighting and others loads of following poles in the exiting MCB DB complite with connections. Testing and commisioning etc as required. |
| 266 | 6/32 amps,single pole, \"B\" SERIES |
| 267 | S/F \"C\" series. S.P.MCB:-Supplying and fixing 6 amps to 32 amps rating,240 volts, \"C\" series miniature circuit breaker suitable for lighting and others loads of following poles in the exiting MCB DB complite with connections. Testing and commisioning etc as required. |
| 268 | 6/32 amps ,DP |
| 269 | 40 amps ,DP |
| 270 | 50/63 amps, DP |
| 271 | P/F M.V. danger notice plate:-Providing and fixing M.V danger notice plate of 200mm x150mm made of mild steel, at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in single red coiour on front side as required. |
| 272 | S/L 8 SWG copper wire ground :-Supplying and laying 8 SWG copper wire 0.50 metre bellow ground level for conductor earth electrode, including soldring etc. as required. |
| 273 | P/F G.I. lightning conductor finial:-Providing and fixing of lighting cnductor finial, made of 25 mm dia 300mm long, copper tube having single prong at top, with 85mm dia 3mm thick G.I. base plate including holes etc. complete as required. |
| 274 | Reverting, sweating and soldering of copper/G.I. tape(with another coppr/G.I. tape, base of the finial or any other metallic object) as required. |
| 275 | P/F G.I. lightning conductor tape in horizontal run:-Providing and fixing copper tape 20mm x 3mmthick on parapet or surface of wall for lightning conductor complete as required(For horizontal run) |
| 276 | P/F G.I lightning conductor tape in vertical run:-Providing and fixing copper tape 20mm x 3mmthick on parapet or surface of wall for lightning conductor complete as required(for vertical run) |
| 277 | P/F Testing joint for G.I. lighting conductor:-Providing and fixing testing joint, made of 20mm x 3mm thick G.I. strip, 125mm long, with 4 nos.of G.I. bolts, nuts, chek nuts and spring washers etc complete as required. |
| 278 | Laying of one number PVC insuleted and PVC sheathed/ XLPE power cable of 11 KV grade of size not exceeding 35 sq.mm.but not exceeding 95 sq.mm. direct in ground including excavetion, sand coushioning, protective covering and refilling the trench etc as required. |
| 279 | Supplying and fixing of light class G.I. pipe of 50 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required |
| 280 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 281 | 3½ X 50 sq. mm (35mm) |
| 282 | 3½ X 70 sq. mm (38mm) |
| 283 | S/L PVC XLPE insuletd PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts,(conforms to IS:1554, part-1) |
| 284 | 50 sq.mm. 3.5 core |
| 285 | 70 sq.mm. 3.5 core |
| 286 | Providing of 12\"\" (300 mm)exhaust fan of make bajaj/havells/usha/crompton |
| 287 | SITC of 48\"\" (1200 mm) ceiling fan of make bajaj/havells/usha/crompton |
| 288 | SITC of Reces/surfaces mounted LED rounddown light (15/16 watt) of make bajaj/havells/crompton |
| 289 | SITC of LED street light (90/100 watt) of make bajaj/havells/crompton |
| 290 | SITC of LED TUBE LIGHT (20/22 watt)of make bajaj/havells/crompton |
| 291 | Supplying and fixing of LED 15/16 W of make bajaj/havells/crompton |
| 292 | Earthing with copper earth plate 600x600x3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc (with charcoal or coke and salt) as required….. |
| 293 | Mian Panel(LS)Power Distribution Board (PDB at GL) - Supplying, designing, manufacturing, installation, testing, fitting, fixing and commissioning in correct alignment position, effecting proper connection of all incomers and outgoing of PDB panel of 16 SWG CRCA Sheet steel IP-54 floor mounting cubical type LT Panel suitable for operation on 415V, 50Hz, 3Ph, AC supply and fault level 35kA. Apporexmate size (Shall be given at the time of work order ) with front operated construction including seperate fabrication arrangement for fixing of switchgears and meters. The sheet steel under go minimum seven tanks treatement followed by finishing poder coating of minimum 60 microns thickness duly compart mentalized with locking arrangement duly fixed on base channel size 100mm X 75mm X 6mm having accessories mounted inside cubicale panel, earthing with 2 Nos. of earth studs.All opening shall be covered by soft rubber gaskit,enclosure shall be galvanished. Panel shall have suitable cable entry from top and bottom and suitable arrangement for multiruns aluminium cables for MCCB. |
| 294 | The panel includes 415V, 200A, 3Ph, 36KA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082 of suitable length andinsulated by heat shrinkable sleeves Red, yellow, Blue and Black asR Y B & N.The current density of bus bar shall be minimum 0.8 A / sq mm.All inter connections from main Bus Bar to MCCB up to 100A shall be with suitable size of Bus Bar and below 100A MCCB the interconnection shall be made with 4, 6 & 10Sq mm PVC Cu. wire. |
| 295 | The panel includes 415V, 200A, 3Ph, 36KA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082 of suitable length andinsulated by heat shrinkable sleeves Red, yellow, Blue and Black asR Y B & N.The current density of bus bar shall be minimum 0.8 A / sq mm.All inter connections from main Bus Bar to MCCB up to 100A shall be with suitable size of Bus Bar and below 100A MCCB the interconnection shall be made with 4, 6 & 10Sq mm PVC Cu. wire. |
| 296 | Incomers:- 160A, 35 kA FP MCCB adjestable thermal seting - 1 no, with front rotary handle with thermo magnetic releas160 AMPFP CHANGEOVER SWITCH 1 No.Outgoings:- 16nos-32Amps DPMCB ,SP MCB 10KA-16 Nos,3amp Auto chengeover 16 No.s, DP MCB Isoletor 4 nos,Digital Am-meter, three phase, and Digital Volt-meter, three phase 3 nos-Phase indicating light with 2 A SP MCB\"s for protection 3 nos .Make- AE / Vaishno/C&S/ CHINT 3 nos-CT 1500/5VA -5 classEpoxy resin cast CT(3 Nos.)=2 Set. Make:-Kappa / Matrix . Provisioning ofSpace for 16 nosElectronic meter in Panel+ cost of 16 gauge iron sheet to be fabricated for panel mountred switch disconnector, including bus bar chamber, insulation painting etc as required( but without bus bar copper strip)(ALL SWITCHGEARS SHOULD BELEGARAND, SCHINEDER ,SIEMENS MAKE) PANEL BUILDER MAKE- STECH POWER INDUSTRIES /,MEDITRON/TRANZITE/JMD ELECTROTECH |
| 297 | Add 12% GST |
| 298 | Add 1% Lebour Cess |
AI Tender Summary
Tender Timeline
Sep 02, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedSep 15, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedSep 20, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender