Aug. Of Wss Tipper Pokhar Karad, Bagi, Bala Zehra And Shilli Ropa In Anni Block Distt. Kullu Hp S.H Const Of Rcc Intake Chambers 8 Nos , Treatment Units Sedimentation Tank, Filter Units ,Const Of Pump House For Stage 1St And Iind Stage Above 55Hp, Sump
Tender Value
84.16 Lakhs
Estimated cost
Bid Submission
14 Sep 2021
0 days left
EMD
1.33 Lakhs
Bank guarantee accepted
Document Fee
800
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Anni → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Aug. Of Wss Tipper Pokhar Karad, Bagi, Bala Zehra And Shilli Ropa In Anni Block Distt. Kullu Hp S.H Const Of Rcc Intake Chambers 8 Nos , Treatment Units Sedimentation Tank, Filter Units ,Const Of Pump House For Stage 1St And Iind Stage Above 55Hp, Sump Well Cum Storage Tank At Point A 155000, Point B 35000 And Storage Tank At Point C 20000 An
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundation and trenches up to all depths and in all classification of earth work such as pick work, jumper work, situated soil including bailing or pumping out of water, blasting soft or hard rock or chiseling or wedding out of soft/hard rock where blasting is prohibited, in all lifts including trimming and dressing of sides, labeling of beds to correct grade including shoring, strutting, planking, timbering and dewatering wherever required.Stacking usable and unusable material /soil separately and after lying jointing and testing of pipes, returning the usable soil in 15cm layers by ramming and watering and then disposing of all surplus excavated soil/ unusable material as directed with in all leads/ lifts including restoration of un-metalled surfaces to its original conditions and including cost of diversion for traffic, night signal boards, fixing caution boards, crossing over trenches for access to houses, fencing etc. Complete in all respects within all lee\ads and lifts as per direction of the Engineer-in-Charge. |
| 2 | Providing and laying cement concrete 1:3:6(1 cement:3 sand:6 graded stone agg. 40mm nominal size) and curing complete excluding cosot of form work and reinforcement of RCC work in foundation and plinth with in all leads and lifts as per directionand to the entire satisfaction of the Engineer-in-charge. |
| 3 | Providing and laying cement concrete 1:6:12(1cement: 6sand: 12 graded stone agg.40mm nominal size) and curing complete excluding cost of centering and shuttering including with in all leads and lifts as per directionand to the entire satisfaction of the Engineer-in-charge.. a) Foundation and plinth |
| 4 | Providing and laying cement conc 1: 1½ :3 (1cement:1:1½ sand :3 graded stone agg. 20mm nominal size) and curing com-plete excludidng cosot of form work and reinforcement for RCC work in foundation and plinth with in all leads and lifts as per directionand to the entire satisfaction of the Engineer-in-charge in:- |
| 5 | Foundation,footing basis of columns & the likeand mass concrete. |
| 6 | Walls (any thickness) but not less that 0.10 Mtrs. hick including attached pilasters buttresses plinth and string course from top of foundation upto floor two levels. |
| 7 | Suspended floors, roofs, landings, shelves and their supports balconies, beams girders bressumers and cantilevers upto floor two levels |
| 8 | Arches up to floor two level |
| 9 | Providing and laying cement conc 1: 2 :4 (1cement:1:2 sand :4graded stone agg. 20mm nominal size) and curing com-plete excludidng cosot of form work and reinforcement for RCC work inSuspended floors, roofs, landings, shelves and their supports balconies, beams girders bressumers and cantilevers upto floor two levels |
| 10 | Providing form work with steel plate 3.15 m.m thick welded with angle iron 30x 30 x5 m.m so as to give a fair finish including centering ,shuttering, propping etc. height of propping and centering below supporting floor to ceiling upto all heights and removal of the same for in-situ reinforced conc.and plain conc.work inwith in all leads and lifts as per directionand to the entire satisfaction of the Er-in-charge. |
| 11 | Flat surface such as soffits and suspended floors, roofs, landings and the like: Floors etc. up to 200mm in thickness within all leads and lifts |
| 12 | Vertical surfaces such as walls (any thickness)portions and the like including attached pilaster buttresses plinth and string course and the like |
| 13 | Foundation,footing basis of columns & the like and mass concrete. |
| 14 | Beams, cantilever Girders& lintals sides&soffitsof beams, beams,haunching cantilever girdersnot exceeding 1mtr. Depth. |
| 15 | Providing fromwork of ordinary timber planking’s so as to givea fair finish i/c centering, shuttering, strutting and propping etc. with wooden battens & ballies, height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for in-situ reinforced concrete and plain concrete work with in all leads and lifts as perthe direction of the Engineer-in-charge in :- |
| 16 | Arches beyond 6.0 mtrs. Span. |
| 17 | Providing tor steel reinforcement for RCC work including bending, binding and placing in position i /c binding wire complete up to floor two level complete in all respect as per direction & to the entire satisfaction of Engineer-in- Charge upto all lead & lifts. |
| 18 | Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1cement:3 sand) with in all leads and lifts as per the entire satisfaction & direction of the Engineer - in - Charge. |
| 19 | Layingjointing of G.I pipes (L.G) ,tube fitting in trenches I ee/c earth work complete for inlet and scour pipe including all leads and lifts. |
| 20 | G.I Pipe 50 mm (LC) |
| 21 | G.I Pipe 65mm (LC) |
| 22 | G.I Pipe 80 mm (LC) |
| 23 | Providing & fixing CI Sluice valve (with hand wheel) as per IS : 780-1984 class-I upto 300mm dia.(i/c brass spindle & as per 2906-1984class-II for dia.> 300 mm) complete with bolts nuts,rubber insertion etc.,(the tail piece if required shall be measured & paid for separatly with in all leads and lifts as per directionand to the entire satisfaction of the Engineer-in-charge. |
| 24 | 80mm Dia. |
| 25 | 50mm Dia. |
| 26 | Providing , Supplying& fixing of MS Fabricated Protection Panel 750 mm x 600 mm made with MS Angle 40 x 40 x 4 mm for frame, MS Angle 30 x 30 x 3 mm for cover, MS Flat 25 x 5 mm for fixing of sliding door bolt and MS Sheet 3.15 mm thick for protection of manhole covers of storage tanks including the cost of cutting and welding of MS angle, MS Flat & MS Sheet, provision for providing and fixing sliding door bolt 300 x 16 mm, MS Handle 100 mm, Lock and applying a coat of red lead paint & painting two coat with steel paint (Firoza Blue) complete job in all respect in all leads and lifts and to the entire satisfaction of the Engineer - in - Charge. ( Manhole Cover) |
| 27 | Providing and placing in horizontal layers filtering media duly graded, screened cleaned and washed as per specifiedin all respectas per direction & to the entire satisfaction of Engineer-in- Charge upto all lead & lifts. |
| 28 | Top layer : Fine sand( Eff. Size 0.2mm to 0.4mm and uniformity co- effcient 2 to 3mm) |
| 29 | Second layer: Coarse sand, 3mm to 6mm |
| 30 | Third layer: Bajri 6mm to 20mm |
| 31 | Fourth layer: Bajri 20 mm to 25mm |
| 32 | Bottom Layer: Broken stone 50mm to 75mm |
| 33 | Providing laying and placing RCC precast slab size 300mmX400mmX50mm in cement concrete 1:2:4 (1 Cement: 2Sand: 4 Graded stone aggregate 20mm nominal size and curing complete including cost of steel and form work complete in all respect within all lead and lifts as per the direction of Engineer-in-Charge. |
| 34 | Providing and layingcement concrete 1:2:4 (1cement :2sand: 4graded stone aggregate of 20mm nominal size)and curing complete excluding cost of form workRCC work (Cement concrete drain in CC 1:2:4 under the precast the slab , size of drain 0.10x 0.25 x 80 mt.) including all leads and lifts |
| 35 | Steel work welded in built up sections,trusses & framed work i/c cutting, hoisting & fixing in position & applying a priming coat of red paint :-In grating, framed ,guards, bars,ladders, railing,brackets & similar works with in all leads and lifts as per the entire satisfaction & direction of the Engineer Incharge |
| 36 | Constructing chamber for sluice valve, with CI surface box 100 mm top dia.,160 mm bottom dia. & 180 mm deep(inside) with chained lid RCC top 1:2:4 mix (1 cement :2 sand :4 graded stone aggregate 20 mm nominal size) 100 mm thick foundation concrete 1:5:10 mix (1cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) & inside plastering with cement mortor 1 :3 (1 cement : 3 sand) finished with a floating coat of neat cement i/c curing complete.600 x 600 x 750 mm inside size With 150 mm thick walls of RCC 1:2 :4 (1 cement :2 sand :4 graded stone aggregate 20mm nominal size) complete with form work & reinforcement with 6 mm bars at not exceeding 150 mm centres both ways with in all leads and lifts as per the entire satisfaction & direction of the Engineer Incharge . |
| 37 | Providing and fixing GMS Ventilating pipe 100mm dia, 1mtr. Height with C.I Cowl fixed at top complete in all respect within all lead and lifts as per the direction of Engineer-in-Charge. |
| 38 | Random rubble masonary/Polygonal rubble masonary (coursed or brought to courses withhard stones of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 in cement mortar 1:6 ( 1 cement : 6 sand)as per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts. |
| 39 | Brick work using comman burnt clay building bricks in super structure Ist Class above plinth level upto floor two level with C.M 1:6 ( 1 cement :6 Sand ) with in all leads and lifts as per direction & satisfaction of Engineer -in-charge. |
| 40 | Half brick work using common burnt clay building bricks in superstructure above 1stfloor level in cement mortar 1:4( 1Cement, 4 Sand ) of 2nd class bricks complete in all respect with in all leads and lifts. |
| 41 | Providing wood work in frames of doors, windows, clearstory, windows and other frames wrought framed and fixed in position: 2nd class deodar wood with in all leads and lifts as per directionand to the entire satisfaction of the Engineer-in-charge. |
| 42 | Providing and fixing panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c bright 2nd class deodar wood 40mm thick with in all leads and lifts as per directionand to the entire satisfaction of the Engineer-in-charge. |
| 43 | Pointing on brick work with cement mortar 1:3 ( 1 cement, 3 sand ) with in all leads and lifts complete in all respect. Raised and cut |
| 44 | Providing and laying brick tiles over mumty roofs grouted with cement mortar 1:3 ( 1 cement,3 sand ) over a 12 mm layer ofC.M 1:3 ( 1 cement, 3 sand ) and finished neat with in all leads and lifts complete in all respect. |
| 45 | 6 mm thick cement plaster to ceiling in C.M.1:3 (1Cement,3 sand) with in all leads and lifts complete in all respect. |
| 46 | 15 mm thick cement plaster in single coat on rough side of brickstoneconcrete walls for interior plastering up to floor -2 level including arrisses,internal rounded angles,chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with in all leads and lifts in C.M 1:6 ( 1 cement,6 sand ) with in all leads and lifts as per directionand to the entire satisfaction of the Engineer-in-charge. |
| 47 | 20 mm thick cement plaster in single coat on rough side of brickstoneconcrete walls for interior plastering up to floor -2 level including arrisses,internal rounded angles,chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with in all leads and lifts in C.M 1:6 ( 1 cement,6 sand )with in all leads and lifts as per directionand to the entire satisfaction of the Engineer-in-charge. |
| 48 | Providing and fixing MS grills of required pattern in wooden frames of window etc with M.S flat square or round bars with round headed bolts and nuts or by screw within all leads and lifts complete in all respect. |
| 49 | Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of IS gauge specification 8 S.Gwith wire of dia 0.56 mm for doors,windows ic bright finished blackenamelled iron butt hinges with necessary screws 30 mm thick of 2nd class deodar wood with in all leads and lifts complete in all respect. |
| 50 | Boulder filling under floor as per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts. |
| 51 | Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm dia metres bolts, nuts and wooden plug and embedding in cement concrete block 30x10x15cm. 1:3:6( 1cement:3sand:6 graded stone att. 20mm nominal size) within all leads and lifts and as directed by the Engineer-in-charge. |
| 52 | Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement: 3sand: 6graded stone agg. 20mm nominal size) i/c finishing the top surface of concrete smooth within all leads and lifts and as directed by the Engineer-in-charge. |
| 53 | ProvidingProviding under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground. within all leads and lifts and as directed by the Engineer-in-charge. |
| 54 | White washing with lime on undecorated wall surfaces(two coats) to give an even shade I/c thoroughly brooming the surface to remove all dust dirt & other foreign matter as per direction & to the entire satisfaction of Engineer-in- Charge upto all lead & lifts. |
| 55 | Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer ofapprovedbrand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primeras per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts. |
| 56 | Finishing wall with water proofing cement paint of approved brand and manufacture and ofrerquired shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials. |
| 57 | Providing and fixing anodised aluminiumsliding door boltswith bolts and nuts screws etc. complete and as per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts. |
| 58 | Providing and fixing anodised aluminiumtowerbolts ( barrel type)with screws etc. complete and as per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts |
| 59 | Providing ad fixing anodised aluminiumhandleswithnecessary screws etc. complete as per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts. |
| 60 | Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,greese,dirt and other foreign matters,sand papering and knotting.Ready mixed paint brushing wood primer pink. as per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts. |
| 61 | Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping with animal paint other then white andas per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts. |
| 62 | Terrazzo tile flooring with precast terrazzo tiles 20 mm thick with marble chips of specified size laid in floors,treads of steps and landing on a bed of 25 mm average thickness of cemenrt mortar 1 :6 ( 1 cement,6 sand ) jointed with neat cement slurrymixed with pigment to match the shade of tilewhere ever required including rubbing and polishing complete with tiles of following shades medium with in all leads and lifts complete in all respect. |
| 63 | Wiring for light point / fanpoint /exhaust fan /call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable inPVC casing & capping and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge.(Group C) |
| 64 | Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required. complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. |
| 65 | 2x1.5 Sq.mm |
| 66 | 2x4.0 Sq.mm |
| 67 | (a)Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as required. |
| 68 | (b)Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as |
| 69 | (a)Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as required |
| 70 | (b)Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as required. |
| 71 | Supplyingand fixing wooden boxes of following sizes (nominal size) on surface or in recess suitable for fixing phenolic laminated sheet cover in front including painting etc. as required:- complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. |
| 72 | 229mm x102mm x60mm deep. |
| 73 | 203mm x152mm x60mm deep. |
| 74 | Supplying and fixing ceiling rose on the existing junction box / wooden block including connections etc. as required complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. |
| 75 | Supplying and fixing plain pendant with 16/ 20mmtwin twisted, flexible, PVC insulated, cotton braided, copper cable and bakelite pendent holder including connections etc. as required. |
| 76 | Supplying and erection of 6 ampsto 63 amps rating,10 KA breaking capacity, 240 volts. \"C\" curves miniature circuit breaker of following poles in the existing MCB DB complete with connection etc. as required. complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. |
| 77 | Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board240 Volts on surface / recess, complete with tinned copper bus bar wire set netural link earthbar, din-bar detachable gland plate, blanking plate, cable, identification labels inter connection, phosphatized and powder painted, including earthing etc. as required. complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. Single door -8 way. |
| 78 | Supplying and fixing of following rating, double pole (Single phase and netural) 240 volts, isolater inthe existing MCB DB complete with connections testing and commissioning as required. complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. |
| 79 | 63 Amps Cat-A |
| 80 | Providing, installation, testing and commissioning of ceiling fan with ragulator, including wiring the down rods of standard length (up to 30 cm ) with 16/0.20 mtr. Twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required. complete with in all lead & lifts and to the entire satisfaction of the Engineer-in-Charge.(Category - A ) |
| 81 | Providing & fixing ulta slim decorative extruted box fixture with domestic electronic ballast, snap-on installets, suitable for 28 Watt FLT (T5) complete with all accessories (including one No. T-5 Tube) connections, testing & commissiong etc as required. complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. |
| 82 | 1x28 Watt-FLT (T5) (Cat-A) |
| 83 | Providing and fixing following type of surface mounting decorative mirror optics luminaire with powder coated CRCA sheet steel housing, low glare aluminium mirror reflector, prewired with 110 V starter & 36/40 w copper ballast for housing CFL (but excluding the cost of CFL), complete with all accessories, connections, testing and commissioning etc. as required. |
| 84 | Providing and fixing two core service wire 6mm thick. complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. |
AI Tender Summary
Tender Timeline
Sep 01, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedSep 14, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedSep 15, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender