Tender For Civil, Electrical And Ac Works For Construction Of Ware House And Site Office Building At Kknpp 3 And 4 Sites Kudankulam Tamilnadu- 1 1 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. 2 2.1 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil 3 3.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) 4 3.2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size). 5 3.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size). 6 4 Providing contraction / expansion joints in cement concrete floor by concrete cutting machine (up-to 6mm to 10mm width & 40mm to 50mm depth) etc., complete and as directed by Engineer-in-charge. 7 5.1 Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade A sealing compound. Note: Please read the unit as per cm depth per cm width per m length 8 6 Providing and laying dry rubble soling including filling interstices with morrum etc., complete and as directed by Engineer-in-charge. 9 7.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand) 10 8 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 11 9.1 Supplying, filling and consolidating at site Good earth 12 10.1 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). 13 11 Reinforced cement concrete work in beams, suspended floors, roofs with slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). 14 12.1 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 15 13.1 Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete 16 13.2 Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers 17 13.3 Centering and shuttering including strutting, propping etc. and removal of form for all heights : Weather shade, Chajjas, corbels etc., including edges 18 13.4 Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 19 13.5 Centering and shuttering including strutting, propping etc. and removal of form for all heights : Suspended floors, roofs, landings, balconies and access platform 20 14.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) 21 15.1 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) 22 16 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry 23 17 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge. 24 18.1 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) 25 19.1 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster 26 20.1 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) 27 21 Neat cement punning. 28 22.1 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer 29 23.1 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 30 24.1.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) 31 24.2.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) 32 25 Providing and fixing powder coated aluminium grill (minimum thickness of powder coating 50 micron) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). 33 26.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness 34 26.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness 35 27 Extra for etching on float glass panes etc., complete and as directed by Engineer-in-charge. 36 28.1 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides 37 29 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (with brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. Make: Godrej / Everite / Equivalent. 38 30.1 Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge Powder coated minimum thickness 50 micron aluminium 39 31.1 Providing and fixing powder coated aluminium tower bolts (minimum thickness of powder coating 50 micron) ISI marked, to required colour or shade, with necessary screws etc. complete : 200x10 mm 40 32 Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 41 33.1 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters 80x1.25 mm M.S. laths with 1.25 mm thick top cover 42 34 Providing and fixing ball bearing for rolling shutters. 43 35 Providing and fixing of 1.5 HP motor For operating rolling shutter including gear box, wiring, remote controlled and necessary accessories etc., complete and as directed by Engineer-in-charge. Note: Any missing items not mentioned but required for the completion of the job and are essential to be taken into account without any additional cost to the department. 44 36 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 45 37.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes 46 38.1 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete 47 38.2 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 48 39 Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. 49 40 Providing and fixing bolts including nuts and washers complete. 50 41 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 51 42.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm plus 0.05 percent total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling or self tapping screws complete : Ridges plain 500 to 600mm 52 42.2 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm plus 0.05 percent total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling or self tapping screws complete : Flashings/ Aprons.( Upto 600 mm) 53 42.3 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm plus 0.05 percent total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling or self tapping screws complete : Gutter .(600 mm over all girth) 54 43.1 Supply and application of anti corrosion primer NITOZINC Primer of FOSROC or equivalent product approved by the Engineer-in-charge as per manufacturer s recommendation for structural steel or exposed reinforcement including manpower, brushes, scaffolding arrangements etc., complete and as directed by Engineer-in-charge. Two or more coats on new work 55 44.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work 56 45 Labour charges for VDF vibrator for finishing the cement concrete floor etc., complete and as directed by Engineer-in-charge. 57 46 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 58 47 Providing and fixing 2mm Polycarbonate sheet in roof for ventilation, the sheet shall be fixed using self drilling / self tapping screws of size 5.5x55mm with EPDM seal up-to any pitch in horizontal / verticle or curved surfaces and including cutting to size and shape wherever required etc., complete and as directed by Engineer-in-charge. 59 48 Providing and fixing imported turbine exhaust of 500 mm dia with light weight aluminium construction, Dupont delrin casin with Teflon protective top and bottom bearings and washers and fitted with grade 200 type 316 stainless balls designed for Kudankulam wind speed, including all necessary fixtures, constructive washers etc., soaker flange to required profile with standard bolts, nuts etc., with the manufacturing guarantee and it should be watertight etc., complete and as directed by Engineer-in-charge. 60 49 Providing and fixing of Daiken/Armstrong mineral fibre false ceiling with hot dipped galvanised steel grid work, surface chemically cleaned capping perfectly pre finished in backed polyster paint, main tees of size 33x24x0.5mm thick at every 1.2m center to center perimeter with L-angle 24x24x0.5mm thick to form a grid of size 600x600mm and suspending the grid from RCC roof using 12 guage GI wire and rawl plug at every 1200mm intervals wherever required and laying Daiken/Armstrong mineral fibre acoustic ceiling tiles pattern of size 600x600x14mm over the formed grid etc., complete and as directed by Engineer-in-charge. NOTE: False ceiling tiles not layed at the place of electrical fittings should be handed over to department (ECIL). 61 50.1 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm 62 51.1 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm 63 52 Supply and fixing of vertical venetian blinds 4 width as per user s requirement with necessary accessories and approved colour etc., complete and as directed by Engineer-in-charge. 64 53.1 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm 65 54 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres 66 55 Supply and installation of MS fabricated portable security cabin of size 1.80x1.80x2.40 m with necessary electrical fixtures, windows, door and including transport charges etc., complete and as directed by Engineer-in-charge. Note: Technical specifications are enclosed. You are requested to quote as per the detailed technical specifications. 67 56 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 68 57 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete. 69 58.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes with thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc 25 mm nominal outer dia Pipes 70 58.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, with thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc 15 mm nominal outer dia Pipes 71 59.1.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, with thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal outer dia Pipes 72 59.1.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, with thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal outer dia Pipes 73 60.1 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore 74 60.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore 75 61.1.1 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore Horizontal 76 61.1.2 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 40 mm nominal bore Horizontal 77 62.1 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore 78 63.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 79 64.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid 80 65.1 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Single half stall urinal with 5 litre P.V.C. automatic flushing cistern 81 66 Providing and fixing white vitreous urinal divisions of approved quality and colour etc., complete and as directed by Engineer-in-charge. 82 67.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap 83 68 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. 84 69.1.1 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm 85 70.1.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia 86 71.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore 87 72.1 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15mm nominal bore 88 73 Providing and fixing CP brass two in one tap of 15mm nominal bore etc., complete and as directed by Engineer-in-charge. Make: Hindware / Jaguar / Cera 89 74 Providing and fixing health faucet with 1.0 metre extendable metal tube and holder etc., complete and as directed by Engineer-in-charge. Make: Jaguar / Hindware. 90 75 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 91 76.1 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length 92 77.1 Providing and fixing CP brass, push cock for urinal of approved quality. 15 mm nominal bore 93 78 Providing and fixing PVC nahani traps including CP jali of approved quality etc., complete and as directed by Engineer-in-charge. 94 79.1 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 40 mm diameter 95 79.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter 96 79.3 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter 97 80.1.1 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door 75x75x75 mm 98 80.1.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door 110x110x110 mm 99 80.2.1 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door 75x75x75 mm 100 80.2.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door 110x110x110 mm 101 80.3.1 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5degree 75 mm bend 102 80.3.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5 110 mm bend 103 80.4.1 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 75 mm Shoe 104 80.4.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe (Plain) 110 mm Shoe 105 81.1.1 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 106 82.1 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter 107 83.1 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm diameter S.W. pipe 108 84.1.1 Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design 0.91 m deep with SFRC cover and frame (heavy duty, HD20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 109 85 Providing and fixing WPC (wood plastic composite) work in frame of doors, clerestory windows and other frame of thickness 75mm, door shutter of thickness 25mm including S.S pressed butt hinges of required size etc., complete and as directed by Engineer-in-charge. 110 86 Providing and fixing ventilators made with UPVC (unplasticised polyvinyl chloride) with suitable sections for frames and necessary fixtures, fastners etc., including 5mm thick float glass for louvers with necessary arrangements and filling the gap in between UPVC frame & adjacent RCC/brick work by providing weather silicon sealant etc., complete and as directed by Engineer-in-charge. 111 87.1 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm 112 88.1 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm 113 89.1 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm 114 90 Providing and laying of brick bat concreting 1:5:10 (1 cement:1 coarse sand:10 brick bats) for toilet flooring with water proofing treatment etc., complete and as directed by Engineer-in-charge. 115 91.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 116 92.1 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank 117 93 Providing and fixing vent cowl size of 110mm dia etc., complete and as directed by Engineer-in-charge. 118 94 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, with minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs with 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and with manufacture s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 119 95 Providing and fixing 760x760 mm (outer) 2.5 mm thick GI manhole colver including frame, ensure after fixing of manhole cover including frame opening should be 600mmx600mm etc., complete and as directed by Engineer-in-charge. 120 E1.1 Supply and laying of following 1100V grade XLPE insulated PVC sheathed armoured heavy duty Al. Cables of approved make conforming to IS-7098 (Part-I) specifications inside the building on wall / floor / beam/ in trenches and outside the building in existing trenches from LT panel / DB panel to required loads including supply of all required fasteners and civil works etc., complete. 3.5 Core 150 Sq.mm armoured Al. cable. Make: Finolex / KEI / Universal / L&T 121 E1.2 Supply and laying of following 1100V grade XLPE insulated PVC sheathed armoured heavy duty Al. Cables of approved make conforming to IS-7098 (Part-I) specifications inside the building on wall / floor / beam/ in trenches and outside the building in existing trenches from LT panel / DB panel to required loads including supply of all required fasteners and civil works etc., complete. 3.5 Core 70 Sq.mm armoured Al. cable. Make: Finolex / KEI / Universal / L&T 122 E1.3 Supply and laying of following 1100V grade XLPE insulated PVC sheathed armoured heavy duty Al. Cables of approved make conforming to IS-7098 (Part-I) specifications inside the building on wall / floor / beam/ in trenches and outside the building in existing trenches from LT panel / DB panel to required loads including supply of all required fasteners and civil works etc., complete. 3.5 Core 50 Sq.mm armoured Al. cable. Make: Finolex / KEI / Universal / L&T 123 E1.4 Supply and laying of following 1100V grade XLPE insulated PVC sheathed armoured heavy duty Al. Cables of approved make conforming to IS-7098 (Part-I) specifications inside the building on wall / floor / beam/ in trenches and outside the building in existing trenches from LT panel / DB panel to required loads including supply of all required fasteners and civil works etc., complete. 3.5 Core 25 Sq.mm armoured Al. cable. Make: Finolex / KEI / Universal / L&T 124 E1.5 Supply and laying of following 1100V grade XLPE insulated PVC sheathed armoured heavy duty Al. Cables of approved make conforming to IS-7098 (Part-I) specifications inside the building on wall / floor / beam/ in trenches and outside the building in existing trenches from LT panel / DB panel to required loads including supply of all required fasteners and civil works etc., complete. 4 Core 10 Sq.mm armoured Al. cable. Make: Finolex / KEI / Universal / L&T 125 E2.1 Jointing the above mentioned cable with suitable Terminations including supply of all jointing materials like cable glands, sockets, lugs, necessary fasteners and making provision in DB / LT panel for incoming & outing of cable with earthing of glands etc., complete. 3.5 Core 150 Sq.mm armoured Al. cable. Make: Raychem / Denson / HMI 126 E2.2 Jointing the above mentioned cable with suitable Terminations including supply of all jointing materials like cable glands, sockets, lugs, necessary fasteners and making provision in DB / LT panel for incoming & outing of cable with earthing of glands etc., complete. 3.5 Core 70 Sq.mm armoured Al. cable. Make: Raychem / Denson / HMI 127 E2.3 Jointing the above mentioned cable with suitable Terminations including supply of all jointing materials like cable glands, sockets, lugs, necessary fasteners and making provision in DB / LT panel for incoming & outing of cable with earthing of glands etc., complete. 3.5 Core 50 Sq.mm armoured Al. cable. Make: Raychem / Denson / HMI 128 E2.4 Jointing the above mentioned cable with suitable Terminations including supply of all jointing materials like cable glands, sockets, lugs, necessary fasteners and making provision in DB / LT panel for incoming & outing of cable with earthing of glands etc., complete. 3.5 Core 25 Sq.mm armoured Al. cable. Make: Raychem / Denson / HMI 129 E2.5 Jointing the above mentioned cable with suitable Terminations including supply of all jointing materials like cable glands, sockets, lugs, necessary fasteners and making provision in DB / LT panel for incoming & outing of cable with earthing of glands etc., complete. 4 Core 10 Sq.mm armoured Al. cable. Make: Raychem / Denson / HMI 130 E3 Supply, installation, testing and commissioning of Cubical wall mounted / floor mounted enclosure box for suitable to fixing of following distribution boards as per the SLD, made out of 2 mm CRCA sheet steel, pretreated with 7 tank process and painting with Epoxy powder coated of approved shade. Bottom/Top entry for all cables with suitable gland plates of required sizes, Aluminium bus bars @ 0.8A/Sq.mm rating and neutral shall have the half rating of phase and comprising of following complete as per IS earthing of Panel and switches etc. Incomings: 400A, MCCB with Microprocessor based over current and earth fault relay protection - 01 No. 1) Digital Multifunction Meter with RS485 comm - 1N0. Suitable CTs for above MCCB (Metering) and 3Phase indication lamps. Outgoings: a) 160A, MCCB with Microprocessor based over current relay protection - 02Nos. b)100A, MCCB with Microprocessor based over current relay protection - 04Nos. Make: Schneider / L&T / Siemens / ABB 131 E4.1 Supply and installation of sheet steel flush mounted double door type three phase vertical bus-bar MCCB / VTPN distribution board with phase and neutral to install on wall / column including cable end boxes, MS angular frame work with necessary accessories, internal wiring, earthing, painting, numbering, and minor civil works etc., complete. 160A, 12-way TPN DPX MCCB DB (Cat No: 5077 48) Make: Legrand / L&T / Siemens / Schneider 132 E4.2 Supply and installation of sheet steel flush mounted double door type three phase vertical bus-bar MCCB / VTPN distribution board with phase and neutral to install on wall / column including cable end boxes, MS angular frame work with necessary accessories, internal wiring, earthing, painting, numbering, and minor civil works etc., complete. 8-Way VTPN DB (Cat No: 5077 27) Make: Legrand / L&T / Siemens / Schneider 133 E4.3 Supply and installation of sheet steel flush mounted double door type three phase vertical bus-bar MCCB / VTPN distribution board with phase and neutral to install on wall / column including cable end boxes, MS angular frame work with necessary accessories, internal wiring, earthing, painting, numbering, and minor civil works etc., complete. 12-Way SPN DB (Cat No: 5076 11) Make: Legrand / L&T / Siemens / Schneider 134 E5.1 Supply and Fixing of following MCCB/MCBs in the above mentioned distribution board including required wiring, identification & numbering complete as per the directions of Engineer In-charge. 160A DPXMCCB (Cat No: 4200 97) Make: Legrand / Siemens / Schneider 135 E5.2 Supply and Fixing of following MCCB/MCBs in the above mentioned distribution board including required wiring, identification & numbering complete as per the directions of Engineer In-charge. 160A ELM (Cat No: 4201 17) Make: Legrand / Siemens / Schneider 136 E5.3 Supply and Fixing of following MCCB/MCBs in the above mentioned distribution board including required wiring, identification & numbering complete as per the directions of Engineer In-charge. 63A FPMCB (Cat No: 4087 02) Make: Legrand / Siemens / Schneider 137 E5.4 Supply and Fixing of following MCCB/MCBs in the above mentioned distribution board including required wiring, identification & numbering complete as per the directions of Engineer In-charge. 63A RCCB (Cat No: 4118 88) Make: Legrand / Siemens / Schneider 138 E5.5 Supply and Fixing of following MCCB/MCBs in the above mentioned distribution board including required wiring, identification & numbering complete as per the directions of Engineer In-charge. 63A TPMCB (Cat No: 4086 61) Make: Legrand / Siemens / Schneider 139 E5.6 Supply and Fixing of following MCCB/MCBs in the above mentioned distribution board including required wiring, identification & numbering complete as per the directions of Engineer In-charge. 40A DPMCB (Cat No: 4086 37) Make: Legrand / Siemens / Schneider 140 E5.7 Supply and Fixing of following MCCB/MCBs in the above mentioned distribution board including required wiring, identification & numbering complete as per the directions of Engineer In-charge. 40A DPRCCB (Cat No: 4118 82) Make: Legrand / Siemens / Schneider 141 E5.8 Supply and Fixing of following MCCB/MCBs in the above mentioned distribution board including required wiring, identification & numbering complete as per the directions of Engineer In-charge. 32A TPMCB (Cat No: 4086 58) Make: Legrand / Siemens / Schneider 142 E5.9 Supply and Fixing of following MCCB/MCBs in the above mentioned distribution board including required wiring, identification & numbering complete as per the directions of Engineer In-charge. 32A/20A/10A SPMCB (Cat No: 4085 90/93/95) Make: Legrand / Siemens / Schneider 143 E6 Supply and Installation of 63A TPN 5 pin plug & socket P17 Tempra model (Cat No.5078 64) with 63A, 300mA FPRCCB (Cat No.4118 93) to install on DB with suitable knock out for incoming cables to draw the three phase power supply including MS frame work to fix on wall / column with required fasteners, earthing, painting, numbering and minor civil works etc., complete. Make: Legrand / L&T / Siemens / Schneider 144 E7 Supply and Installation of 32A TPN 5 pin plug & socket P17 Tempra model (Cat No.5078 62) with 40A, 300mA FPRCCB (Cat No.4118 92) to install on DB with suitable knock out for incoming cables to draw the three phase power supply including MS frame work to fix on wall / column with required fasteners, earthing, painting, numbering and minor civil works etc., complete. Make: Legrand / L&T / Siemens / Schneider 145 E8 Supply and Installation of 250 V grade 3-pin metal clad protected weather proof plug socket, housed in Legrand MS box with 20A socket (Cat No.5078 14) with plug top controlled by 20A, 300mA DPRCCB (Cat No.4118 61) including earthing, neutral link internal wiring, painting and numbering etc., complete to fix on suitable MS bracket / frame work to wall / column as detailed. Make: Legrand / L&T / Siemens / Schneider 146 E9.1 Supply and installation of following modular type plug sockets with Modular type switches with Including supply of suitable mounting boxes, Dummies, Inner plates, Cover plates with internal wiring and minor civil works etc., complete. 2-Way 6/16A Modular Power socket controlled by 2 Nos of 16A Modular switch. Make: North West / Legrand / L&T/Schneider 147 E9.2 Supply and installation of following modular type plug sockets with Modular type switches with Including supply of suitable mounting boxes, Dummies, Inner plates, Cover plates with internal wiring and minor civil works etc., complete. 4-Way 6A Modular Power sockets controlled by 4 Nos of 6A Modular switches. Make: North West / Legrand / L&T/Schneider 148 E10 Supply and installation of 600mmX600mm recessed type 34-40W LED false ceiling lighting fixtures with LEDs mounted symmetrically inside the fitting and with equal distribution of light including control circuitry duly wired to operate at 150-290VAC, 50Hz to be fixed to beam / ceiling / on false ceiling including supply of all necessary clamps supports, chains, pipes, fasteners, ball & sockets where needed and earthing etc., complete Make: Philips / Crompton / Havells / Syska LEDs: OSRAM/ Nichia / Cree 149 E11 Supply and Installation, testing and commissioning of 04 feet industrial (Aluminium body) box type LED lighting fixture of 20-22 watts LED lamps with necessary accessories like Electronic driver to be fixed to wall / beam / ceiling / on false ceiling including supply of all necessary accessories like supports, pipes, ball and sockets where needed, fasteners and earthing etc., complete. Make: Philips / Crompton / Havells / Syska/ wipro LEDs: OSRAM/ Nichia / Cree 150 E12 Supply and Installation, testing and commissioning of 02 feet industrial (Aluminium body) box type LED lighting fixture of 10-15 watts LED lamps with necessary accessories like Electronic driver to be fixed to wall / beam / ceiling / on false ceiling including supply of all necessary accessories like supports, pipes, ball and sockets where needed, fasteners and earthing etc., complete. Make: Philips / Crompton / Havells / Syska/wipro/ Bajaj LEDs: OSRAM/ Nichia / Cree 151 E13 Supply and installation of 400mm sweep oscillating type wall mounted fan suitable to operate on single phase 230V 50Hz AC supply to be installed on Wall / Column with required MS frame work, wiring and necessary civil works etc., complete. Make: Orient / Bajaj / Almonard 152 E14 Supply and Installation of high speed 1400mm sweep ceiling fan capacitor type suitable to operate on 230 volts AC supply with blades, down rod, top and bottom canopies to ISS 374/1979 double ball bearing including Northwest make electronic step type speed control 2 module regulator and necessary fan hook to fix to ceiling / beam with required accessories and fasteners etc., complete. Fan make: Orient / Havells / Crompton Regulator make: North West / Legrand 153 E15.1 Supply of following IP66 powder coated Aluminium body with toughned glass visor and efficacy not less than 100 lm/w and 5700 Kelvin temperature including necessary accessories. 100W LED Flood light fixture Make: Philips / Crompton /Havells /Syska/ wipro 154 E16 Supply and installation of 300 mm dia. drift air type exhaust fan suitable to operate on 230V, 50Hz single phase AC supply in existing hole, grouting of suitable nuts and bolts and as per the directions of Engineer In-Charge. Make: Crompton / Havells / Orient 155 E17 Supply and installation of 450 mm dia. 900 rpm industrail type heavy duty Exhaust fan suitable to operate on 230V, 50Hz single phase AC supply, in existing hole with all required accessories including louvers, minor civil works complete etc. Make: Crompton / Havells / Orient 156 E18.1 Supply and drawing of 600V grade PVC insulated copper FRLS wires in existing surface / recessed steel / PVC conduit in different colours preferably black colour for neutral and green colour for shield including interconnections etc., complete. 2 X 4 Sq.mm PVC copper wire Make: Finolex / KEI / Universal / RR Kabel / Lapp / BONTON 157 E18.2 Supply and drawing of 600V grade PVC insulated copper FRLS wires in existing surface / recessed steel / PVC conduit in different colours preferably black colour for neutral and green colour for shield including interconnections etc., complete. 2 X 2.5 Sq.mm PVC copper wire Make: Finolex / KEI / Universal / RR Kabel / Lapp / BONTON 158 E18.3 Supply and drawing of 600V grade PVC insulated copper FRLS wires in existing surface / recessed steel / PVC conduit in different colours preferably black colour for neutral and green colour for shield including interconnections etc., complete. 1 X 2.5 Sq.mm PVC copper wire Make: Finolex / KEI / Universal / RR Kabel / Lapp / BONTON 159 E18.4 Supply and drawing of 600V grade PVC insulated copper FRLS wires in existing surface / recessed steel / PVC conduit in different colours preferably black colour for neutral and green colour for shield including interconnections etc., complete. 1 X 1.5 Sq.mm PVC copper wire Make: Finolex / KEI / Universal / RR Kabel / Lapp / BONTON 160 E18.5 Supply and drawing of 600V grade PVC insulated copper FRLS wires in existing surface / recessed steel / PVC conduit in different colours preferably black colour for neutral and green colour for shield including interconnections etc., complete. 5 X 6 Sq.mm PVC copper wire Make: Finolex / KEI / Universal / RR Kabel / Lapp / BONTON 161 E18.6 Supply and drawing of 600V grade PVC insulated copper FRLS wires in existing surface / recessed steel / PVC conduit in different colours preferably black colour for neutral and green colour for shield including interconnections etc., complete. 1 X 10 Sq.mm PVC copper wire Make: Finolex / KEI / Universal / RR Kabel / Lapp / BONTON 162 E18.7 Supply and drawing of 600V grade PVC insulated copper FRLS wires in existing surface / recessed steel / PVC conduit in different colours preferably black colour for neutral and green colour for shield including interconnections etc., complete. 3 core 2.5 Sqmm flexible cable Make: Finolex / KEI / Universal / RR Kabel / Lapp / BONTON 163 E18.8 Supply and drawing of 600V grade PVC insulated copper FRLS wires in existing surface / recessed steel / PVC conduit in different colours preferably black colour for neutral and green colour for shield including interconnections etc., complete. 3 core 2.5 Sqmm flat cable Make: Finolex / KEI / Universal / RR Kabel / Lapp / BONTON 164 E19.1 Modular Point Wiring With 2 Nos. of multi strand 1.5 Sq.mm PVC insulated FR copper wire preferably black colour for neutral of 1100 volts grade, FRLS PVC conduit pipe from 20mm / 25mm / 32mm to be laid on walls (Surface / recess), columns, furniture (including supply of conduit and its accessories) supported on saddles with number of wires bunched at certain places, controlled by 6A, 250V single pole Modular type switches for light / fan point including 6A socket for wall mounting fan, ceiling rose for tube light fixture / ceiling fan and 15A Modular type switches for Flood light, flush marked mounted on suitable mounting boxes (MS), Inner plates, Cover plates with internal wiring. Supply being tapped from DB with 2 nos. of multi strands 2.5 Sq.mm PVC copper wire for primary Light / Fan. Supply of all necessary accessories like, ceiling rose, BH/AH, 6A, MS junction box earthing the installation with 1.5 Sq.mm PVC copper wire (Green colour) and numbering etc., complete. One switches controlling one light / Fans. Make: Finolex/L&T (wires) & North West / Legrand / L&T Switches. 165 E19.2 Modular Point Wiring With 2 Nos. of multi strand 1.5 Sq.mm PVC insulated FR copper wire preferably black colour for neutral of 1100 volts grade, FRLS PVC conduit pipe from 20mm / 25mm / 32mm to be laid on walls (Surface / recess), columns, furniture (including supply of conduit and its accessories) supported on saddles with number of wires bunched at certain places, controlled by 6A, 250V single pole Modular type switches for light / fan point including 6A socket for wall mounting fan, ceiling rose for tube light fixture / ceiling fan and 15A Modular type switches for Flood light, flush marked mounted on suitable mounting boxes (MS), Inner plates, Cover plates with internal wiring. Supply being tapped from DB with 2 nos. of multi strands 2.5 Sq.mm PVC copper wire for primary Light / Fan. Supply of all necessary accessories like, ceiling rose, BH/AH, 6A, MS junction box earthing the installation with 1.5 Sq.mm PVC copper wire (Green colour) and numbering etc., complete. One switches controlling two lights. Make: Finolex/L&T (wires) & North West / Legrand / L&T Switches. 166 E20.1 Supply and laying of heavy duty medium class FRLS PVC conduit pipe with necessary accessories such as bends, junction boxes, reducers etc., on wall (surface / recess) / column / beam / roof / concealed in wall supported on saddles, clamps, including all minor civil works, welding of strips, painting, earthing etc., complete and as per instructions of Engineer In- charge. 25 mm dia. FRLS PVC conduit pipe. Make: VIP / Sudhakar / Precision 167 E20.2 Supply and laying of heavy duty medium class FRLS PVC conduit pipe with necessary accessories such as bends, junction boxes, reducers etc., on wall (surface / recess) / column / beam / roof / concealed in wall supported on saddles, clamps, including all minor civil works, welding of strips, painting, earthing etc., complete and as per instructions of Engineer In- charge. 20 mm dia. FRLS PVC conduit pipe. Make: VIP / Sudhakar / Precision 168 E21.1 Supply and fixing of following communication outlet sockets to be mounted in a cover plates fixed to wall / columns / departmental supplied modular furnitures. RJ11 telephone Make: Northwest/ Legrand / L&T 169 E21.2 Supply and fixing of following communication outlet sockets to be mounted in a cover plates fixed to wall / columns / departmental supplied modular furnitures. RJ 45 LAN (CAT-6) Make: Northwest/ Legrand / L&T 170 E22.1 Supply and Installation of MS powder coated Telephone Distribution boxes with crones & lock facility and connected fasteners etc., complete 20 Pair DB box of size 8.5 X 8.5 171 E23.1 Supply and laying of 0.5mm dia annealed copper conductor armoured following telephone cables in laid conduits, DWC pipes, modular furnitures raceways etc., and as per the instructions of Engineer In-charge. 20 pair Jelly filled armoured Telephone cable Make: Finolex / Delton 172 E23.2 Supply and laying of 0.5mm dia annealed copper conductor armoured following telephone cables in laid conduits, DWC pipes, modular furnitures raceways etc., and as per the instructions of Engineer In-charge. 04 pair PVC Telephone cables Make: Finolex / Delton 173 E24 Supply & laying Giga speed structured network cable CAT-6 in existing laid conduits, modular furnitures raceways etc., and and as per the instructions of Engineer In-charge. Make: Amp/D-link/Finolex 174 E25.1 Supply and fixing of following Modular convex type cover plate to be fixed on modular furniture / GI Metal box on walls / Columns. 2-Modular cover plate Make: Northwest/ Legrand / L&T 175 E26 Supply and Installation of Two-Module modular metal enclosure boxes including fixing in the wall surface / recess, modular furniture with minor civil works etc, Make: Northwest/ Legrand / L&T 176 E27.1 Supply and Installation of following Perforated MS cable tray, Including fixing of supports joined with suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 375 x 50 x 2mm cable Tray 177 E28 Supply, Installation, Testing & Commissioning of new Earth pits as per IS 3043 with UL Listed 3/4 copper bonded steel rod of 3 Mtrs long, scope of work includes all civil works like excavation of pit (3 Mtrs depth), backfilling the pit with Carbon based chemical Ground Enhancement material of 22.5KG to be supplied by the contractor including construction of chamber for the pit, frame around the pit, supply of pit cover, measurement of earth pit resistance complete as per the instructions of Engineer In-charge. 178 E29.1 Excavation of about 1Mtr deep suitable width trench for accommodating following runs of LT power armoured cable in all types of soils including road cutting, floor cutting with neat cement plastering as encountered on site and provision of sand cushioning on top and bottom of cable, placing of bricks to either sides and top of cable, back filling, tapping, including supply and fixing of LT cable route markers at every 15Mtrs interval as instructed by Engineer in Charge. 3.5 Core 150 Sq.mm armoured Al. cable. 179 E29.2 Excavation of about 1Mtr deep suitable width trench for accommodating following runs of LT power armoured cable in all types of soils including road cutting, floor cutting with neat cement plastering as encountered on site and provision of sand cushioning on top and bottom of cable, placing of bricks to either sides and top of cable, back filling, tapping, including supply and fixing of LT cable route markers at every 15Mtrs interval as instructed by Engineer in Charge. 3.5 core 70 Sqmm Al. armoured cable. 180 E29.3 Excavation of about 1Mtr deep suitable width trench for accommodating following runs of LT power armoured cable in all types of soils including road cutting, floor cutting with neat cement plastering as encountered on site and provision of sand cushioning on top and bottom of cable, placing of bricks to either sides and top of cable, back filling, tapping, including supply and fixing of LT cable route markers at every 15Mtrs interval as instructed by Engineer in Charge. 3.5 Core 25 Sq.mm armoured Al. cable. 181 E29.4 Excavation of about 1Mtr deep suitable width trench for accommodating following runs of LT power armoured cable in all types of soils including road cutting, floor cutting with neat cement plastering as encountered on site and provision of sand cushioning on top and bottom of cable, placing of bricks to either sides and top of cable, back filling, tapping, including supply and fixing of LT cable route markers at every 15Mtrs interval as instructed by Engineer in Charge. 4 Core 10 Sq.mm armoured Al. cable. 182 E30 Excavation of about 0.5 Mtr deep suitable width trench for accommodating DWC pipe for drawing telephone cable in all types of soils including road cutting, floor cutting with neat cement plastering as encountered on site as instructed by Engineer in Charge. 183 E31 Supply and laying of 9 dia RCC pressure hume pipe with required collars for road crossing including road cutting of 1 Mtr deep for laying the 150 sqmm aluminium armoured cable and backfilling of excavated soil and making the surface to original shape including all civil works. 184 E32.1 Supply and laying of hot dip GI /Copper strip / wire as under including interconnections and tapping, wherever necessary on wall / partition / trench / underground by excavation from earth pit to the building, with required civil works like welding, clamping and painting etc., complete. 50 x 6 mm G.I strip 185 E32.2 Supply and laying of hot dip GI /Copper strip / wire as under including interconnections and tapping, wherever necessary on wall / partition / trench / underground by excavation from earth pit to the building, with required civil works like welding, clamping and painting etc., complete. 25 x 6 mm G.I strip 186 E32.3 Supply and laying of hot dip GI /Copper strip / wire as under including interconnections and tapping, wherever necessary on wall / partition / trench / underground by excavation from earth pit to the building, with required civil works like welding, clamping and painting etc., complete. 25 x 3 mm G.I strip 187 E32.4 Supply and laying of hot dip GI /Copper strip / wire as under including interconnections and tapping, wherever necessary on wall / partition / trench / underground by excavation from earth pit to the building, with required civil works like welding, clamping and painting etc., complete. N0.8 SWG G.I wire 188 E33 Supply of 440V insulating mats of class A 2mm Thickness with Antiskid abberations on top side and plain surface on bottom side confirming to IS 15652-2006 (All the details like IS number and manufacture details are to be embossed on the mat) Make: Electromat / Electrosafe 189 E34 Supply and laying of 40x32 mm DWC (Double Walled Corrugated pipe) directly in ground level of existing 0.5 mtr deep outdoor trench and as per the directions of Engineer in-charge. Make: CPE / Telerex / Sudhaker 190 E35 Supply & installation of openwell 0.5 HP submercible pump consisting of cast iron impeller, sauction and delivery as 1 inch along with MCB / starter panel board with dry run protection suitable to operate on 230V, 50Hz AC supply. Make: Crompton/ V-Guard /Kirloskar/ Texmo 191 E36 Crimping/termination of Giga speed structured network cable CAT-6 in existing RJ45 socket /LAN Hub and temination of 20 pair/04 pair telephone cable in existing RJ11 socket or krone box and per the instructions of Engineer In-charge. 192 AC.1 Supply of 2.0 TR high wall mounted split air conditioner indoor unit and condensing units cooper coil only, (3 star rated) including 3.0 rmt. Cooper pipe (suction and discharge) are standard kit, insulation material drain pipe, electrical cord etc., complete and as directed by Engineer-in-charge. Make: Blue Star, Voltas, Daikin, LG Electronic India Ltd. 193 AC.2 Installation, testing and commissioning of the above including closing of holes and as directed by Engineer-in-charge. 194 AC 3 Supply of suitable 2.0 TR condenser stands and as directed by Engineer-in-charge. 195 AC 4 Supply of copper pipe (suction & discharge) for 2.0 TR air conditioners. 196 AC 5 Supply of electrical cable for 4 core x 2.5 sqmm. Make: Finolex, Legrand, KEI, Polycab.
