|
| 1 | Cutting in earth work and disposal of excavated earth upto a lead of 20 metres:- P/J Work within all leads and lifts. |
| 2 | Excavation in foundationsin all kinds of soil such as pick work ,jumper work, blasting hard or soft rock chiseling where blasting is prohibited or saturated soil , lift upto 1.50 mtr stacking the excavated soil not more than 3.00 mtr clear from the edge of the excavation and then returning the stacked soil in 15 cm layers when required into plinth sides of foundation consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in-Charge. |
| 3 | Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm nominal size) excluding cost of centring and shuttering in: Foundations and plinth: |
| 4 | Providing & Laying Cement concrete work 1:1.5:3 (1 cement : 1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in : |
| 5 | Foundation footings bases of columns and the like and mass concrete. |
| 6 | Vertical walls (any thickness attached pillesters, buttresses plinth and string courses etc. form top of foundation and plinth. |
| 7 | Suspended floor, roofs, landing shelves and their support balconies beams, griders. bressumers and cantilever within all lead and lifts. |
| 8 | Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: |
| 9 | a) Vertical surfaces such as walls (any thickness) partitions and the like including attached pillaster buttresses, plinth and string courses and the like with in all leads and lifts. |
| 10 | b) Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Lloors etc. upto 200mm. In thickness with in all leads and lifts. |
| 11 | Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3 (1 cement:3 sand) |
| 12 | Providing tor steel reinforcement for RCC work including bending binding and placing in position complete upto floor two level to the entiresatisfaction of the Engineer in charge.Tor steel with in all leads and lifts. |
| 13 | Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint. In gratings framed guard bars, ladders, railling,brackets and similar works. |
| 14 | Providing and fixing Gate Valve, CI Sluice Valve (with hand wheel) as per IS: 780-1984 class-I upto 300mm dia. (i/c brass spindle & as per 2906-1984 class-II for dia> 300mm) complete with bolts nuts, rubber insertion etc., (the tail pipce if required shall be measured & paid for separatly) |
| 15 | 80mm dia |
| 16 | Manufacturing and supplying of MS Wheel Valve Chamber of size 450x450x450mm made of 2.0mm MS Sheet fixed on top & all four sides with ISA 35x35x4mm frame as per drawing. Pieces of MS Flat 20x4mm, 0.10m long be fixed on all sides as hold fast. The operation of manufacturing shall including cutting of MS Sheet, Angle Section & welding of MS Sheets, Angle Section, Hinges, Handles 150mm long, 20x4mm flats, locking arrangement and applying a priming coat of steel primer after pretreatment of surface to the entire satisfaction of the Engineer-in-Charge. |
| 17 | Providing and fixing of 3.15mm MS Sheet Manhole cover 600X600mm fixed on all sides with ISA 40x25x5mm top angle iron frame hinged on ISA 35x35x5mm bottom angle iron frame as per drawing. Pieces of MS Flat 20x4mm, 0.15m long be fixed on all sides as hold fast. The operation of manufacturing shall including cutting of MS Sheet, Angle Section & welding of MS Sheets, Angle Section, Hinges, Handles 150mm long, 20x4mm flats, locking arrangement and applying a priming coat of steel primer after pretreatment of surface to the entire satisfaction of the Engineer-in-Charge. |
| 18 | Providing and laying cement concrete 1:4:8 (1 cement: 4 sand: 8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in. |
| 19 | Providing and laying cement concrete 1:2:4 (1 cement: 2 sand: 4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in foundation and plinth |
| 20 | Random rubble masonry/polygonal rubble masonry (Uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including levelling and plinth including levelling up with cement concrete 1:6:12 (1 cement:6 sand: 12 graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1 cement: 6 sand) in breast walls and retaining walls. Including all lead lifts and carriage of material at site and as per the direction of Engineer in Charge. |
| 21 | Providing and fixingangle Ironposts 2.50m high 50X50X5mm and welding of wire mash of interlink chain with in all leads and lifts as per the direction of Engineer - in - charge |
| 22 | Providing, fixing & welding of MS Flat 40 x 5 mm with in all leads and lifts as per the direction of Engineer - in - charge |
| 23 | Applying priming coat over new steel & other metal surface after & including preparing the surface by thoroughly cleaning oil, grease, dirt & other foreign matter & new paper complete with ready mixed paint brushing red lead/red oxide/zinc oxide chrome. |
| 24 | Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paintbrushin to give an even shade including cleaning the surface of all dirt,dust and other foreginmatters Enamel paint other than white :-- |
| 25 | Providing and fixing MS Grill Gate |
| 26 | Providing and laying cement concrete 1:5;10 (1cement :5sand :10 graded stone aggregate 40mm. nominal size) with 15 % plum and curing complete excluding cost of form work in retaining walls/ Breast walls, the size of plums shall usually be 150mm. to 300mm as per H.P.P.W.D.Specification. |
| 27 | Stone soling under flooring in all leads and lifts. |
| 28 | Laying & Jointing in treanches GMS tube (MG) and tube fitting (earth work in trenches to be measured and paid seprately) as per the direction of the Engineer-in-Charge including all fittings complete. |
| 29 | 20mm dia |
| 30 | 25mm dia |
| 31 | 32mm dia |
| 32 | 40mm dia |
| 33 | 50mm dia |
| 34 | 65mm dia |
| 35 | 80mm dia |
| 36 | Providing and Fixing Gun Metal peet valve with hand wheel (Superior Quality) complete. |
| 37 | 20mm dia |
| 38 | 25mm dia |
| 39 | 32mm dia |
| 40 | 40mm dia |
| 41 | 50mm dia |
| 42 | 65mm dia |
