Construction Of Sakhi One Stop Centre Building At Una Distt. Una (Hp). Construction Of Sakhi One Stop Centre Building At Una Distt. Una (Hp).
Tender Value
31.34 Lakhs
Estimated cost
Bid Submission
01 Sep 2021
0 days left
EMD
54500
Bank guarantee accepted
Document Fee
3600
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Una → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Sakhi One Stop Centre Building At Una Distt. Una (Hp). Construction Of Sakhi One Stop Centre Building At Una Distt. Una (Hp).
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any leadfrom the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth asperthe directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . |
| 2 | Providing form work with steel plates (3.15mm) three point fifteen milimetre thick welded with angle iron in frame (30x30x5mm) ( Thirty x thirty x five milimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc., with wooden battens and ballies, for all heights of propping and centring below supportingfloor to cailing up to all heights and removal of same for insitu reinforced concrete and plain concrete workincluding carriage of materials with in all leads, lifts and other incidentalsasperthe directions of Engineer-in-Charge. (a).Foundations, footings & bases of columns etc., and mass concrete. |
| 3 | (B).Column, pillars, posts and struts. (i). Square, rectangular or polygonal in plan. |
| 4 | (C).Beams, cantilevers, girders and lintels. i. Sides and soffits of beams, beam haunching, cantilevers, bressumers and lintels not exceeding 1 mtr. In depth in all heights from floor. |
| 5 | (D).Flat surfaces such as soffits of suspended floors, roofs, landing and the like. ( i).Floors etc., upto 200mm( Two hundred milimetre) in thickness. |
| 6 | E) Vertical Surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like. |
| 7 | (f).Stair cases with slopping or stepped soffits excluding landing |
| 8 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing completeincluding carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. |
| 9 | Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm (fourty millimetre) nominal size and curing complete excluding cost of centring and shuttering in Foundation and plinth including carriage of materials with in all leads, lifts and other incidentalsasperthe directions of Engineer-in-Charge. |
| 10 | Providing and laying cement concrete 1:1.5:3 (One cement : one point five sand :Three graded stone aggregate 20mm nominal size)( Twenty milimetre) and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials within all leads and lifts and as perthe direction of Engineer-in-Charge. (a) Foundations, footings, bases of columns and the like and mass concrete. |
| 11 | (b).Columns, pillars, posts and struts in all floor levels. |
| 12 | (c).Suspended floors, roofs, landings and shelves and their support balconies, beams, girders, bressumers and cantilevers in all floor levels. |
| 13 | (d).Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing in all floor levels. |
| 14 | Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in:Foundation and plinth including carriage of materials within all leads and lifts |
| 15 | Providing mild steel/tor steel reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all floor levels (a). Tor steel. including carriage of materials within all leads and lifts and as perthe direction of Engineer-in-Charge. |
| 16 | Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:6 (1 Cement : 6 Sand) First Class Bricks including carriage of material within all leads and lifts. |
| 17 | Brick work using common burnt clay building bricks in superstructure in Cement Mortar 1:6 (1 Cement : 6 Sand) First Class Bricks including carriage of material within all leads and lifts. |
| 18 | Providing and fixing anodised/ dyed aluminium work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws all complete as per architectural drawings and the directions of Engineer-In-Charge. (a) For doors windows and ventilatiors and glazed partitions frames including carriage of material with in all leads and lifts |
| 19 | For shutters of doors windows & ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings where ever required including the cost of PVC/neoprene gaskets as required (fittings and glazing/panelling shall be paid for separately) |
| 20 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc with PVC/neoprens gasket etc. complete as per the architectural drawings and the directions of Engineer-In_charge (cost of aluminium snap beading shall be paid in basic item.) glazing with glass panes of 4mm thickness (weight not less than 10.00 kg/sqm) including carriage of material with in all leads and lifts. |
| 21 | Providing and fixingParticle board bwp phenol bonded exterior/interior grade in partitions Prelaminated board bwp phenol bonded exterior/interion grade both sides. 12mm thick including carriage of material with in all leads and lifts. |
| 22 | Providing and fixing galvanised M.S. wire gauge of IS gauge designation 140 g with wire of dia0.71 mm to windows and clerestory windows including beading of aluminium including carriage of material with in all leads and lifts. |
| 23 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge including carriage of material with in all leads and lifts. |
| 24 | Providing and fixing 90cm high Stain less Steel 304 No. railing for stair case having Bluster 50mm dia. Jointing in steps with electronic gas welding with 3 rows of 20mm dia and top row with 50mm dia and master piece of 150mm dia. At junction complete in all respectincluding carriage of material with in all lead and lift. |
| 25 | Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc., complete: including carriage of material with in all leads and lifts. and as perthe direction of Engineer-in-Charge. (a) 300X16 mm |
| 26 | Providing and fixing anodized aluminium tower bolt (barrel type) anodized transparent or dyed to required shade and colour with screws etc., complete including carriage of material with in all leads and lifts and as perthe direction of Engineer-in-Charge. ( a).250x10mm |
| 27 | ( b).200x10mm (Two Hundred into Ten milimetre) |
| 28 | Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etc., complete: including carriage of materials upto all leads and lifts and as perthe direction of Engineer-in-Charge. (i) 125mm.( One Hundred Twenty Five milimetre) |
| 29 | (i) 100mm.( One Hundred milimetre) |
| 30 | Half brick work masonry in common burnt clay building bricks in super structure above plinth level upto floor all level using first class building bricks in cement mortar 1:4 (1cement : 4sand) including carriage of materials within all leads and lifts and as per the direction of Engineer in charge. |
| 31 | 6mm (Six milimetre) cement plaster to ceiling in cement mortar 1:3 (One Cement is to three Sand) in all floor level. The rate isincluding carriage of materials within allleads andlifts and as perthe direction of Engineer-in-Charge. |
| 32 | 15mm (fifteen milimetres) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) including carriage of materials within allleads andlifts and as perthe direction of Engineer-in-Charge. |
| 33 | 15mm (fifteen milimetres) thickcement plasters insingle coat on fair side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smoothwith cement mortar 1:6 (one cement: six sand) including carriage of materials within allleads andlifts and as perthe direction of Engineer-in-Charge. |
| 34 | Applying Birla white wall care putty two coats over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials within allleads andlifts |
| 35 | Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials within allleads andlifts |
| 36 | Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equivalent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of materials within allleads andlifts |
| 37 | Painting two coats (excluding priming coat) on new steel and other metalsurfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters:-With white enamel paint.or other than whiteincluding carriage of materials upto all leads and lifts and as perthe direction of Engineer-in-Charge including carriage of materials within allleads andlifts |
| 38 | Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty double charged vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of materials within allleads andlifts |
| 39 | Providing and laying granite stone in flooring 20mm(average) thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm.thick including carriage of materials upto all leads and lifts |
| 40 | Providing and laying Coloured digital tiles6 mm( six millimetre) thick in skirting risers of steps and dado of size 30×60cm nitco or its equivalent of approved make and size 12mm ( Twelve milimetre) thickcement mortar 1:3 (one cement istothree sand) and jointing with neat cement slurry including carriage of material within all leads and lifts. |
| 41 | Providing and laying spartic ceremic tiles 5.5mm.thick in flooring (300 x300mm. size)treads of steps laid on a bed of 12mm. thick cement mortar 1:3(1cement: 3 sand) finished with flush pointing in white cement including carriage of materials upto all leads and lifts |
| 42 | Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size) under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials with all leads and lifts |
| 43 | Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paintIn gratings framed guard bars, ladders, railling, brackets and similar works. including carriage of materials upto all leads and lifts |
| 44 | Finishing with floating coat of neat cement slurry incluidng carriage of material within all leads and lifts. |
| 45 | Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished 40 mm thick.including carriage of materials within all leads and lifts |
| 46 | Providing and fixing on wall face PVC(D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqmincluding filling the joints withapproved adhesive complete. 100mm dia pipes including carriage of materials within all leads and lifts |
| 47 | Providing and Laying of Interlocking Concrete Block Pavements having thickness 60 mm ISI Marked as per drawing and Technical Specification Clause 1504 including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. |
| 48 | Constructing manhole with R.C.C top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing:Inside size 800mm x 800mm and 500mm deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm internal dimensions total weight of cover and frame to be not less than 38kg. (Weight of cover 23 kg and weight of frame 15 kg.) With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3) including carriage of material within all leads and lifts. |
| 49 | Providing and fixing to wall ceilling and floor galvainised mild steeel tubes(medium grade)tube fittings and clamps including making good the wallincluding carriage of material within all leads and lifts. (a) 15 mm nominal bore.( Jindal make) |
| 50 | 20 mm nominal bore. ( Jindal make) |
| 51 | Making connection of galvainised steel distribution branch with galvainised mild steel main 20mm to 40mm nominal bore by providing and fixing Tee including cutting and threading the pipes complete including carriage of material within all leads and lifts. |
| 52 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete. Plain bend 110 mm nominal size including carriage of materials within all leads and lifts |
| 53 | Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete. 110 mm dia including carriage of materials within all leads and lifts |
| 54 | Providing and fixing pvc cowl 110mm dia including carriage of materials within all leads and lifts |
| 55 | Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90 mm including carriage of materials within all leads and lifts |
| 56 | Providing and fixing Vitreous china wash down, water closet ( European type W.C pan)Cream shade with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1(1 Cement :1 Sand ) ( Seat and over to be measured and paid for separately)Ordinary closet. including carriage of materials within all leads and lifts |
| 57 | Providing and fixing PVC Coloured / white high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of material within all leads and lifts. |
| 58 | Providing and fixing GI inlet connection for flush pipe with WC panincluding carriage of material within all leads and lifts. |
| 59 | Providing and fixing vitreous china wash basin Cream Shade with single hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fittings.Flat back630x450mmincluding carriage of material within all leads and lifts. |
| 60 | Providing and fixing CP brass waste for wash basin or sink 32 mm diaincluding carriage of material within all leads and lifts |
| 61 | Providing and fixing 100m sand cast iron grating for gully,foor or Nahani trapincluding carriage of material within all leads and lifts.. |
| 62 | Providing and fixing 600x450mm bevelled edge mirror of superior glass mounted on 6 mm thick AC sheet or plywood sheetand fixed to wooden plugs with CPbrass screw and washersincluding carriage of material within all leads and lifts. |
| 63 | Providing and fixing CP brass towel rail complete with CP brass bracketsfixed to wooden pluges with CP brass screws 600x20mmincluding carriage of material within all leads and lifts. |
| 64 | Providing and fixing CP brass bib tap with capastan head 15 mm dia. weight should not be less than 550gm (Jaquar Make) including carriage of material within all leads and lifts. |
| 65 | Providing and fixing CP brass pillar tap with capstan head 15 mm dia weight should not be less than 550gm (Jaquar Make) including carriage of material within all leads and lifts. |
| 66 | Providing and fixing CP stop cock 15mm diaweight should not be less than 550gm .(Jaquar Make)including carriage of material within all leads and lifts. |
| 67 | Providing and fixing CP connection pipe with brass unions 30 cms length 15mm nominal sizeincluding carriage of material within all leads and lifts. |
| 68 | Providing and fixing brass full way valve with wheelincluding carriage of material within all leads and lifts. (1) 15mm nominal bore with Minimum Weight of 300 Gm. |
| 69 | II) 20mm nominal bore with Minimum Weight of 550Gm |
| 70 | Providing and fixing GI or MI union including carriage of material within all leads and lifts. 1)15mm nominal size |
| 71 | II) 20mm Nominal size |
| 72 | Providing and fixing charomium plated brass soap dish with C.P.brass brackets fixed to wooden cleats with C.P. brass screws including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. |
| 73 | Providing and fixing laboratory sink with C.I. or M.S. brackets painted white including cutting holes in walls and making good the same but excluding fittings Vitreous china 600mm x 450mm x 150mm including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. |
| 74 | Providing and fixing PVC water storage tank double core 1000 ltr net capacity complete in all respect. Sintex make weight not less than 22 kg. including necessary fittings including carriageof material within all leads and lifts. |
| 75 | Providing laying (to level and slopes) and jointing reinforced concretelight duty non pressure pipe IS class NP-2 of followinginternal diameter with collar joints including testing of joints completes.150 mm dia including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. |
| 76 | Providing and fixing Zet connectioncomplete in all respect 15 mm Dia including carriageof material within all leads and lifts. |
| 77 | Providing and fixing plastic seat ( Solid/ Hollow type) and cover for wash down water closet with C.P brass hinges and rubber buffers including carriageof material within all leads and lifts. White plastic seat and cover. |
| 78 | Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. |
| 79 | Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. |
| 80 | Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. |
| 81 | Excavation in earth work and filling in 15 cm. layers in foundation and plinths including ramming, watering and consolidating upto any lead and lift including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. |
| 82 | Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous Chinaincluding carriage of material within all leads and lifts. |
AI Tender Summary
Tender Timeline
Aug 25, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedSep 01, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedSep 02, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender