|
| 1 | Civil Work: |
| 2 | Earhwork in excavation for structures as per drawing and technical Specification Clause 305.1 including setting out construction of shoring and bracing bremoval of stums and other deleterious materials and disposal upto a lead of 50m. dressing of side s and bottom and backfilling in trencher with excavated foundations.suitable material. Mord 300. |
| 3 | P/L of cement concrete 1:5:10 (1 cement :5fine sand : 10 graded brick aggregate 40mm nominal size) and curing complete i/c cost of formwork in foundation and floors as per S.I.No. 274 |
| 4 | Sand filling in plinth under floors including watering and ramming including lead upto 50m and lift upto 1.5m etc S.I.No.255 |
| 5 | P/L of cement concrete 1:4:8 (1 cement :4fine sand : 8 gradedstone ballast 40mm nominal size) and curing complete i/c cost of formwork in foundation and floors as per S.I.No. 281 |
| 6 | P/L of R.C.C. 1:2:4 with cement , coarse sand and 2cm gauge stone ballast. Column T beam slab as per SI No. 288 . |
| 7 | Class M-150 brick work in 1:4 cement and Coarse Sand sand of 2.25 fineness modulous mortar in foundation and plinth including supply of all materials, labour and tools and plants etc.required for proper completion of work. As per SOR S.I. No.305(B) |
| 8 | P/L of R.C.C. 1:2:4 with cement , coarse sand and 2cm gauge stone ballast for lintels, sunshade, plinth bendincement coarse sand and stone aggregate 20 mm nominal size (Sch. P.W.D. 283) |
| 9 | Mild steel or Iron in Plain such as R.C.C. work ( when not R.C.C. included in overall rates) wrought to require shape as necessary Including bending for proper complition of work and including supply of steel its wastage bend hooks and authorized overlapping shall be measured up to floor two level as perSOR SI No. 504 (B) |
| 10 | Mild steel or iron work in heavy sizes sich as trusses; builts up gates, door frames, record racks, roof work, gates etc wrought to required form, including drilling holes, rivetting or welding where necessary and aslo including supply of steel, bolts, nut etc. for gate si no. 503 |
| 11 | Supply and fixing Galvanised Corrugated steel Sheet(22gague) |
| 12 | 12 mm thick plaster 1:6 with cement & fine sand rough side single and half brick wall including internal rounded angles chamfers and or rounded angles not exceeding 80mm in grith and finished even and smooth outer & inner side. S I No.586 |
| 13 | Finshing walls with water proffing cement paint of approved make and quality on new work with two coatsto give an even shead includind supply of mmaterial , lalour and T& P etc..required for proper completion of work. For outer side. SI No. 660+661 |
| 14 | Painting or varnishing on iron work in small or new wood work with one coat of redy mixedpriming paint and one coat of approved superior quality ready mixed paint of clear synthetic varnish including for proper completion of Wlrk. Paint to be used should confirm to th ISI No. 103 1950. SI No.641+642 |
| 15 | Supplying, installation, testing and commissioning of Silent type DG Sets, AMF Panel, Bus Ducting/Cable from DG Sets to Essential Panel, Synchornizing Panel Where required, DG Set enclosure room sound insulation/ ventilation/Smoke exhaust as required Earthing of DG Set System control cabling, Fuel tank/Piping/ DG set Exhaustpiping/exhaust Chimney as per CPCB norms, Civil work.Make Mahindra Powerol Generator-DG Set /Cummins power Generator Generator-DG Set or As Approved by Engineer in-Charge. |
