Estimate For Repairing/Renovation Of Sdo Office At Khamanon.
Tender Value
2.98 Lakhs
Estimated cost
Bid Submission
17 Aug 2021
0 days left
EMD
5966
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
KHAMANON → Punjab
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Estimate For Repairing/Renovation Of Sdo Office At Khamanon.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantled conglomerate floor25 mm to 50 mm thick with concrete base |
| 2 | Providing and laying vitrified floor tiles indifferent sizes in light colour shades made using Soluble Salt Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Soluble salt Print Penetration should be up to 1 to 2 mm after the tiles are fired & polished ).a Size 600x600 mm |
| 3 | Scraping of White wash and colour wash |
| 4 | Scraping of Cement Plaster |
| 5 | 12.5 mm thick cement plaster 1:4 |
| 6 | Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish |
| 7 | Colour washing (two or more coats) |
| 8 | Finishing walls with exterior decorative cement based paint such as snowcem, robbiacem etc. two coats to give an even shade. |
| 9 | Regrading terracing of mud plaster covered with tiles or bricks in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud plaster to proper, slope, relaying mud plaster Gobri leaping and tiles or bricks grouted in cement mortar 1:3 (1 cement and 3 fine sand) including replacing unserviceable tiles, or bricks with new over and disposal of unserviceable material to the dumping ground within 50 m lead (The cost of new tiles or bricks excluded). |
| 10 | Applyting bitumen on roofs including heating and carriage of roof. 1.65kg/sqm |
| 11 | Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg. /Sqm top of R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing |
| 12 | Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16. |
| 13 | Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified. |
| 14 | Hollockwood cup board shutter with plywoodpanels or faced on both side fixed in position (excluding the cost of handles bolts hasp withstaple but including the labour for fixing them(A) 30mm thick |
| 15 | Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt)For shutter area above 0.50 sqm |
| 16 | Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :(a) 300mm x 16mm |
| 17 | (b) 250mm x 16mm |
| 18 | Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete |
| 19 | I.S.I Designation No. III (size of door851mm to 1000mm) |
| 20 | Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc. |
| 21 | Painting two or more coats with synthetic enamel paints in all shades on old wood work or metallic or plastered or concrete surface to give an even shade including rubbing down old paint. |
| 22 | Black Granite stone tiles 20mm thick inskirting, risers of steps, dado walls andpillars laid in 12.5mm thick cement mortar1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour forfixing dowel pins and cramps. |
| 23 | Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x 300 mm as approved by Engineer-inCharge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 24 | Providing and fixing in position stainless steel sinks of approved make (to the approval of Engineer-in-charge) 1mm thick,grade-304 (18/8) with waste coupling complete in all respect.(b) Rectangular Sink with Deluxe BorderSingle Bowl Overall Size 555 mm x475mm x 200 mm |
| 25 | PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- |
| 26 | Heavy Gauge PVC Conduit Pipe 25mm dia. (Flushed) |
| 27 | SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB\"s/ RCBO\"s/ RCCB\"s: Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, colorcoded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO\"s/ RCCB\"s in the distribution board (For SP&N distribution board with provision DP MCB\"s/ RCCB\"s/ RCBO\"s as incomer and SP MCB\"s as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB\"s/ RCCB\"s/ RCBO\"s as incomer and SP MCB\"s as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:-(i) SP&N Double Door Distribution Board 4 way each |
| 28 | SUPPLY AND ERECTION OF WIRING ACCESSORIES: |
| 29 | Supply and erection of Modular Cover Frame (Complete set) on the existing metal box including fixing and connection of existing switches and sockets and other petty material etc:-(d) Modular Cover Frame Six Module |
| 30 | (c) Modular Cover Frame Four Module |
| 31 | Supply and erection of Concealed Metal Boxes of various sizes (1/2M, 3M, 4M, 6M, 8M, 12M, 16/18M) with brass lugs recessed in wall for mounting modular accessories including fixing and other petty material etc., including the cost of cutting and filling up of chases (with finishing the surface):- |
| 32 | (d) Powder Coated Concealed Metal Box with Brass Lugs Six Module |
| 33 | (c) Powder Coated Concealed Metal Box with Brass Lugs four Module |
| 34 | RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: |
| 35 | Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½\" deep for walls and CI 3\" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- |
| 36 | Wiring light point |
| 37 | (i) a Wiring fan point (Without fan box) |
| 38 | Wiring call-bell point |
| 39 | Wiring 6Amp. wall socket point |
| 40 | Wiring 6Amp. Plug control comprising wall socket point |
| 41 | SUPPLY AND ERECTION OF WIRING ACCESSORIES: |
| 42 | Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.,:- |
| 43 | (xviii) Step type Modular Electronic Fan Regulator 100watts (One Module) |
| 44 | 6/10amp. One Way Modular Switch (One Module) |
| 45 | 6amp. 2/3 Universal Modular Shuttered Socket (two Module) |
| 46 | Call Bell 220/230 volts AC Ding Dong |
| 47 | MINIATURE CIRCUIT BREAKERS/ RCBO\"s/ RCCB\"s: |
| 48 | MINIATURE CIRCUIT BREAKERS:Supply and erection of Miniature Circuit Breaker MCB\"s for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- |
| 49 | MCB Single Pole 40amp. (10kA, Curve-C) |
| 50 | MCB Triple Pole 40amp. (10kA, Curve-C) |
| 51 | Providing and fixing 110 mm dia . U.P.V.C Rain water pipe of 2.5 kgf./sqm as per IS:4985 including jointing during masonary complete as per specifications and to the entire satisfaction of Engineer-in- charge. (If fixed on wall face clamp to be paid separatly as per respective item) |
| 52 | Providing and fixing 110 mm dia. U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge.A) UPVC 110 mm bend |
| 53 | Excavation in Soil (any type) using Hydraulic ExcavatorCK 90 and Tippers with Disposal up to 450 metres.Excavation for roadwork in soil with hydraulic excavatorof 0.9 cum bucket capacity including cutting andloading in tippers, trimming bottom and side slopes, inaccordance with requirements of lines, grades andcross sections, and transporting to the embankmentlocation within all lifts and lead up to 450m |
AI Tender Summary
Tender Timeline
Aug 11, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedAug 17, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 17, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender