Works On Air Bottle, Fuel Oil Heaters, Condenser And Lt Cooler On Mv Swaraj Dweep Works On Air Bottle, Fuel Oil Heaters, Condenser And Lt Cooler On Mv Swaraj Dweep
Tender Value
Ref. Documents
Estimated cost
Bid Submission
16 Aug 2021
0 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
HSL Visakhapatnam → Andhra Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Works On Air Bottle, Fuel Oil Heaters, Condenser And Lt Cooler On Mv Swaraj Dweep Works On Air Bottle, Fuel Oil Heaters, Condenser And Lt Cooler On Mv Swaraj Dweep
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 12-Aug-2021 | Due date extension | Date | 16-Aug-2021 |
BOQ
| Sl. No. | Item Description |
| 1 | Auxiliary Air Receiver (Emergency Air Bottle): Auxiliary Air Receiver (01no) to be overhauled, manhole door (no of bolts 20, bolt size 28mm) to be opened up and internal cleaning to be done (pipe line degutting and refitting including) , all mountings (32mm dia valves - 09nos) including relief valve (01no) to be dismantled, cleaned, overhauled and presented for survey, defects to be rectified, relief valve to be rectified as per surveyor recommendations. after survey, relief valve setting to be shown to the surveyor. then all mounting including relief valve to be fitted back in place with new gaskets and fasteners. manhole door to be boxed back with special type gasket. finally, satisfactory trial to be shown to ship staff (air receiver size dia 397mm/length 1700mm, design pressure 32kg/cm2, test pressure 48 kg/cm2. |
| 2 | Consumables / Components / Items / Spares / Material: For executing of the above mentioned jobs, Contractor has to procure, supply all items and fitted in its place. Contractor has to quote lumpsum cost for required Consumables / Components / Items / Spares / Material like valve seat and valve lid, valve spindles, gland packing, MS valve sheels, gland bolts, gland followers, gaskets, O-rings, copper washer, SS bolts & nuts, flange bolt & nuts, relief valve springs, pressure gauge lines and cocks with connectors (copper line) etc., mentioned at S.No. 1 for above scope of work. The taxes will be paid as per actuals. The cost of spares quoted by the contractor will be considered \" on not exceeding basis of total lumpsum cost mentioned in the BOQ for this line item\"\" for satisfactory completion of the specified SoW. Payment will be made at actuals on not exceeding quoted cost of this Serial (1.1) against third party/OEM invoice. |
| 3 | Aux. Engine Fuel Oil Heaters- 02Nos: (Shell & Tube type) both heaters to be removed from place and taken to workshop. High pressure washing and chemical cleaning of heaters to be done. Heaters to be pressure tested to 10 bar. Leaky tube to be plugged. Pressure test shown to ship staff and same to be fitted in place to show satisfactory trial. heater relief valves - 2nos to be overhauled, pressure setting to be done and same to be fitted back in place. (pipe line degutting and refitting including) (Heater length 1700mm dia 220mm) |
| 4 | Consumables / Components / Items / Spares / Material: For executing of the above mentioned jobs, Contractor has to procure, supply all items and fitted in its place. Contractor has to quote lumpsum cost for required Consumables / Components / Items / Spares / Material like chemical, joints, O-rings, copper plugs, SS fasteners, heat resistance paint, drain cock, zinc anodes, end cover etc., mentioned at S.No. 2 for above scope of work. The taxes will be paid as per actuals. The cost of spares quoted by the contractor will be considered \" on not exceeding basis of total lumpsum cost mentioned in the BOQ for this line item\"\" for satisfactory completion of the specified SoW. Payment will be made at actuals on not exceeding quoted cost of this Serial (2.1) against third party/OEM invoice. |
| 5 | Condenser-01No: (Shell & Tube type) Condenser to be removed from place and taken to workshop. Condenser to be cleaned, pressure tested to 5 bar, leaky tubes to be plugged, pressure test shown to ship staff and same to be fitted in place to show satisfactory trial. condenser vent plug stub piece 1nos (3/4 inch dia and 1.5 inches height found holes and leaking same to be renewed. clean condenser to be fitted in place to show satisfactory trial. (pipe line degutting and refitting including) (condenser lenght 910mm, dia 170mm, no fo tube 30Nos approx) |
| 6 | Consumables / Components / Items / Spares / Material: For executing of the above mentioned jobs, Contractor has to procure, supply all items and fitted in its place. Contractor has to quote lumpsum cost for required Consumables / Components / Items / Spares / Material like chemical, joints, O-rings, copper plugs, SS fasteners, heat resistance paint, drain cock, zinc anodes, end cover, vent plug stub pieces etc., mentioned at S.No. 3 for above scope of work. The taxes will be paid as per actuals. The cost of spares quoted by the contractor will be considered \" on not exceeding basis of total lumpsum cost mentioned in the BOQ for this line item\"\" for satisfactory completion of the specified SoW. Payment will be made at actuals on not exceeding quoted cost of this Serial (3.1) against third party/OEM invoice. |
| 7 | Fitment of New LT Cooler: New LT Cooler assembly (plate type cooler - approx weight: 1860kgs) to be shifted to engine room from jetty, while shifting of cooler consider all obstructed items like pipe lines, deck hatches, hatch doors, ladders and railings to be degutted and refitted ( if required new LT Cooler to be dismantled, shifted to position, assembled, pressure tested and fitted in postion). Existing inboard LT Cooler to be removed and new cooler to be fitted in place. necessary pipe lines and foundation modification to be done to fit new cooler in place and satisfactory that to be shown to shipstaff. |
| 8 | Consumables / Components / Items / Spares / Material: For executing of the above mentioned jobs, Contractor has to procure, supply all items and fitted in its place. Contractor has to quote lumpsum cost for required Consumables / Components / Items / Spares / Material like end connection pipe lines, seals, SS fasteners and gaskets (for cooler and degutting items) etc., mentioned at S.No. 4 for above scope of work. The taxes will be paid as per actuals. The cost of spares quoted by the contractor will be considered \" on not exceeding basis of total lumpsum cost mentioned in the BOQ for this line item\"\" for satisfactory completion of the specified SoW. Payment will be made at actuals on not exceeding quoted cost of this Serial 4.1 against third party/OEM invoice. |
AI Tender Summary
Tender Timeline
Aug 12, 2021
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 16, 2021
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
CompletedAug 16, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 16, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender