Development Of Water Aerodrome At Shaheed Dweep Neil Island In South Andaman Under, Cdi, A.Pwd Port Blair Sw Landside Developmental Works
Tender Value
4.71 Crore
Estimated cost
Bid Submission
27 Aug 2021
0 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Shaheed Dweep → Andaman And Nicobar Islands
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Development Of Water Aerodrome At Shaheed Dweep Neil Island In South Andaman Under, Cdi, A.Pwd Port Blair Sw Landside Developmental Works
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 19-Aug-2021 | corrneil | Technical Bid | 27-Aug-2021 |
| 2 | 19-Aug-2021 | Revised BOQ | BOQ | 27-Aug-2021 |
BOQ
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 3 | All kinds of soil. |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 5 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal / carriage of excavated earth by mechanical transport at an average lead of 3 km and filling in layers of thickness 20 cm i/c watering rolling minmum 8 tonnes road roller etc as directed by the Engineer-in-charge. |
| 6 | Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. |
| 7 | Beyond 30 cm girth upto and including 60 cm girth |
| 8 | Beyond 60 cm girth upto and including 120 cm girth |
| 9 | Beyond 120 cm girth upto and including 240 cm girth |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 11 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 12 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 40 mm nominal size derived from natural sources). |
| 13 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). |
| 14 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level : |
| 15 | 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived fromnatural sources: 3 graded stone aggregate 20 mm nominalsize derived from natural sources). |
| 16 | 1:2:4 (1 cement : 2 coarse sand (zone-III)derived fromnatural sources: 4 graded stone aggregate 20 mm nominalsize derived from natural sources). |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 18 | Foundations, footings, bases of columns, etc. for mass concrete |
| 19 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 20 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 21 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 22 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. |
| 23 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed ofsand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. |
| 24 | 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
| 25 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 26 | Electric resistance or induction butt welded tubes |
| 27 | Providing and Fixing Polycarbonated sheet of 10mm thick and 1200/2050mm wide having tensile strength of 60-65 Mpa and light transmission of 50% to 80% supplyied in tailored length as per the direction of EIC. |
| 28 | Providing and fixing Polycarbonated sheet of 10mm thick (size, shape and pitch of corrugation as approved by Engineer-in-charge) and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 29 | Extra for providing and fixing wind ties of 40x 6 mm flat aluminiumsection. |
| 30 | Painting with aluminium paint of approved brand and manufacture to give an even shade . |
| 31 | Two or more coats on new work |
| 32 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 33 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. |
| 34 | Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade |
| 35 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 36 | Two or more coats on new work |
| 37 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 38 | Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface |
| 39 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 40 | Construction of Sewage treatment Plant (10 KLD), including transportation charges of all materials to work site, cost of all labour charges, tools & plants, local taxes, GST etc. complete. |
| 41 | Procurement and installation of baggage scanning machine of reputed make, including transportation charges of all materials to work site, cost of all labour charges, tools & plants, local taxes, GST etc. complete. |
| 42 | Procurement and installation of Door Frame Metal Detector (DFMD) of reputed make, including transportation charges of all materials to work site, cost of all labour charges, tools & plants, local taxes, GST etc. complete. |
| 43 | Procurement and installation of fancy wooden office tableof size 1.50 x 0.90m &0.80 m ht for keeping boarding pass while frisking of reputed make, including transportation charges of all materials to work site, cost of all labour charges, tools & plants, local taxes, GST etc. complete. |
| 44 | Procurement and installation of check - in counter of reputed make, including transportation charges of all materials to work site, cost of all labour charges, tools & plants, local taxes, GST etc. complete. |
| 45 | Procurement and installation of HP Desktop Computer,intel core i5 8GB Ram, internal memory 500 GB, LED 19 inch , laser printer, Computer table, rotational chairs of reputed make and UPS with latest configurations of reputed make, including transportation charges of all materials to work site, cost of all labour charges, tools & plants, local taxes, GST etc. complete. |
| 46 | Procurement and installation of steel Chairs consist of 03 Nos. Chair in a bunch of reputed make, including transportation charges of all materials to work site, cost of all labour charges, tools & plants, local taxes, GST etc. complete. |
| 47 | Procurement and installation of rotating chairs of reputed make, including transportation charges of all materials to work site, cost of all labour charges, tools & plants, local taxes, GST etc. complete. |
| 48 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 49 | 12.5 mm thick tapered edge gypsum moisture resistant board |
| 50 | Providing and fixing of external wall system on Light gauge steel frame work with Outer face cement boards as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make. A grove of 2 mm to 3mm shall be maintained and groves shall be sealed with silicon based sealant. The board shall be fixed in a staggered pattern.Screws shall be of counter sunk rib head of 1.60 mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm and internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard size fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately). |
| 51 | Outer face: Outer face having 6mm thick Alco Panel sheet (ACP) fixed on 9mm thick fiber cement board, Type A, as per IS:14862:2000 (high pressure steam cured) inner Face :- 6mm thick Alco Panel sheet (ACP) fixed on 8 mm thick fiber cement board confirming to IS:14862:2000 of type B (high pressure steam cured) |
| 52 | Providing and fixing internal wall panels on Light gauge steel frame work with 6mm thick Alco Panel sheet (ACP) fixed on 8mm thick fiber cement board conforming to IS 14862:2000 of category III type B (High pressure steam cured) as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm.Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately) |
| 53 | 6mm thick Alco Panel sheet (ACP) fixed on Cement Fiber Board 8 mm thick as per IS 14862:2000 of type B (High pressure Steam Cured) |
| 54 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. |
| 55 | Size of Tile 600x600 mm |
| 56 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : |
| 57 | W.C. pan with ISI marked white solid plastic seat and lid |
| 58 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 59 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 60 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 61 | Semi rigid pipe |
| 62 | 32 mm dia |
| 63 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 64 | Providing and fixing PVC pipes including fittings all complete as per direction of EIC |
| 65 | 75 mm dia |
| 66 | 110 mm dia |
| 67 | Supplying and fixing Bio Digester Tank for Septic tank use for 25 users including making ready of the surface for placement of tank etc all complete as per direction of EIC. |
| 68 | P/F CP Hand shower [Health faucet) with 1 mtr PVC tube and long with wall hook all in complete of make Jaguar or Equivalent |
| 69 | Providing and fixing Ivory chrome Angular stop cock with wall flange of approved makeJaguar (KUB-35053F), including fittings,cutting and making good the walls wherever require |
| 70 | Providing and fixing Providing and fixing Ivory chorme towel ring circular shape alongwith necessary brackets and fixing with necessary screw etc completed (Cat 7721) of jaguar and equivalent category. |
| 71 | Providing and fixing Ivory chrome2 Way Bib Cock with wall flange with approved quality conforming to IS:8931 of make Jaguar (cat - 5041) and equvalent catogories ofcrabtree and equivelant |
| 72 | Providing and Fixing Ivory chromeSoap Dish of approved make Jaguar make(CAN-1131N)includingfittings,cutting and making good the walls wherever require : |
| 73 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc. complete. |
| 74 | On steel work |
| 75 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. INTERNAL WORK - EXPOSED ON WALL |
| 76 | 15 mm nominal outer dia Pipes |
| 77 | 25 mm nominal outer dia Pipes |
| 78 | 40 mm nominal outer dia Pipes |
| 79 | 50 mm nominal outer dia Pipes |
| 80 | Providing and fixing CPVC gate valve of approved quality including fixing with necessary solvant etc all complete : |
| 81 | 25 mm nominal bore |
| 82 | 50 mm nominal bore |
| 83 | Providing and fixing CPVC union with necessary srew end etc all complete : |
| 84 | 15 mm nominal outer dia Pipes |
| 85 | 25 mm nominal bore |
| 86 | 40 mm nominal bore |
| 87 | 50 mm nominal bore |
| 88 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20mmnominalsize derivedfromnatural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation,levelling&dressing & finishing the top smooth. |
| 89 | Providing cement concrete surface drain in given average size with 100 mm thick bed concrete with 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) 150 mm thick both side walls with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) i/c 12 mm cement plaster 1:4 ( 1 cement : 4 coarse sand) with floating coat of neat cement inside the drain and its top and exposed surface including earthwork in excavation and disposal of surplus earth within a lead of 50 m. |
| 90 | 23 cm x 23 cm |
| 91 | Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer\"s specification and direction of Engineer-in-charge. |
| 92 | Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with1.60 ± 0.2 mm thickgalvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with keyon one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 93 | Two track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing beadof appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) |
| 94 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thickgalvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),appropriate dimension of uPVC extruded glazing beads and uPVCextrudedinterlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rodof required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge.(Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 95 | Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing beadof appropriate dimension. (Area of window above 1.75 sqm). |
| 96 | Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer\"s specification and direction of Engineer -in- charge. |
| 97 | 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer\"s specification and direction of Engineer-in-charge. |
| 98 | Non decorative finish (matt finish) |
| 99 | Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete. |
| 100 | Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete. |
| 101 | Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete. |
AI Tender Summary
Tender Timeline
Aug 19, 2021
11:30 IST
Tender Published
Tender notice published.
Completed
Aug 27, 2021
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Aug 27, 2021
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
CompletedAug 27, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 27, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender