Provision Of Boundary Wall At 311 Mtn Bde Area Alongwith Certain Spl Repairs To Or Otm Bldg No Tw 555 At Mil Stn Tenga Under Ge 859 Ews Provn Of Soak Well And Septic Tank For Bldg No T-101, Te-104 Near Goc House, Provn Of Boundary Wall At 311 Mtn Bde Ar
Tender Value
15.40 Lakhs
Estimated cost
Bid Submission
24 Aug 2021
0 days left
EMD
30800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
TENGA VALLEY → Arunachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Provision Of Boundary Wall At 311 Mtn Bde Area Alongwith Certain Spl Repairs To Or Otm Bldg No Tw 555 At Mil Stn Tenga Under Ge 859 Ews Provn Of Soak Well And Septic Tank For Bldg No T-101, Te-104 Near Goc House, Provn Of Boundary Wall At 311 Mtn Bde Area Alongwith Certain Spl Repairs To Or Otm Bldg No Tw 555 At Mil Stn Tenga Under Ge 859 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un-reinforced) in ground floor and pavings n exc 15 cm thickness (below or above ground level)complete all as specified and directed. |
| 2 | M&L for Non-skid ceramic tiles 7 to 8 mm thick coloured tiles( square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed. |
| 3 | M&L for 15mm thick screed bed in CM 1:4 finished rough for laying tiles complete all as specified and directed. |
| 4 | M&L for 75mm thick PCC 1:2:4 type B-2 using 40mm graded aggregates as in plinth protection, finishing the top surface even and smooth w/o using extra cement. |
| 5 | Dismantling of wall or ceiling boards any thickness, including cover fillets complete all as specified and directed. |
| 6 | Dismantling boarding any description fixed in any position with nails complete all as specified and directed. |
| 7 | Taking down cement plaster on brick, concrete surfaces etc including racking out joints. hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 8 | M & L for 50 mm thick 2nd class Hard wood clean sawn boarding with butt joints fixed with nails in any situation complete all as specified and directed. |
| 9 | M&L for preparation of surfaces of wood and wood basedmaterials new or old of any description and girth, not otherwise described and treated with two coats of creosote oil complete all as specified and directed. |
| 10 | S&F 6mm thick plywood , graded BWR, type BB fixed with nails to timber frame work fixed to wall surface etc complete all as specified and directed. |
| 11 | S&F 6mm thick plywood , graded BWR, type BB fixed with nails to timber frame work fixed to ceiling surface etc complete all as specified and directed. |
| 12 | M&L for 2nd class hardwood plain fillets, square, rectangular or triangular in section, wrought, secured with nails having sectional area exc. 3 sqcm and n.exc 6 sqcm, complete all as specified and directed. |
| 13 | Material and labour for preparation ofnew wooden wood based materialover 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 14 | M&L for preparing old steel surfaces and applying one coat of synthetic enamel roof paint over 10 cm width or girth on steel surface complete all as specified and directed. |
| 15 | Material and labour for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed. |
| 16 | Dismantling plain or corrugated steel sheeting of any gauge, thickness including nainital or similar roof coverings complete all as specified and directed. |
| 17 | Supply and fix 0.63 mm thick galvanised corrugated steel sheeting with two corrugation side lap fixed with L type or J type or cranked hooks, bolts with grade of zinc coatingcomplete all as specified and directed. |
| 18 | M&L for applying two coats of synthetic enamel paint over one coat of red oxide primer including preparing new zinc (or galvanised) surfaces to receive painting by coating with mordant solution including washing and cleaning etc on steel surfaces of any description complete all as specified and directed. |
| 19 | Taking down Chowkhats or frames exc 1.5 Sq.m but n exc 4 Sq.m each (without taking off shutters from the frame) including all fittings complete all as specified and directed. |
| 20 | Taking down Chowkhats or frames n exc 1.5 Sq.m each (without taking off shutters from the frame) including all fittings complete all as specified and directed. |
| 21 | S&F 2nd class hard wood plain solid straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue , pinned at joints complete all as specified and directed. |
| 22 | S&F window frames, window guard bars fixed independently in wooden frames and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 23 | Supply and fix 2nd class hard wood plain framed panelled shutters35 mm thick (any number of panels) with panels of timber flat on both sides, feather edged or of veneered particle board medium density, wood particle board with commercial face veneer 12 mm thickcomplete all as specified and directed. |
| 24 | M&L for 30mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and direted. |
| 25 | Supply and fix 100mm long MS butt hinge medium weight cold rolled complete all as specified and directed. |
| 26 | S&F 150mm longaluminium anodized, barrel tower bolts made of extruded section complete all as specified and directed. |
| 27 | S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised. handle fabricated type complete all as specified and directed. |
| 28 | S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy complete all as specified and directed. |
| 29 | S&F pre coated mild steel floor door stopper tongue anodised 140mm length including vulcanised rubber piece complete all as specified and directed. |
| 30 | S&F PVC coated 25mm dia mild steel curtain rod medium weight and fixing brackets, curtain rings @ 7 Nos per metre and decorative end support etccomplete all as specified and directed. |
| 31 | S&F for sheet glass 3 mm thick figured glass, pin head type glazing with oil putty/ wooden beads in squares n exc. 0.50 sqm in each pane complete all as specified and directed. |
| 32 | S & F GI steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm etc all as specified. |
| 33 | Material and labourfor applying two coats of synthetic enamel paint over a coat of red oxide primer to steel and iron surfaces of any description over 10 cm in width or girth not otherwise described including preparation of new steel surfaces complete all as specified and directed. |
| 34 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 35 | M&L for PCC 1:3:6 type C-1 (20 mm graded stone aggregate) as in roof kerb or mud stops, plinth walls including necessary formwork complete all as specified and directed. |
| 36 | Excavation over areas n exc 1.5m deep and getting out in hard/dense soil complete all as specified and directed. |
| 37 | Returning , filling including spreading levelling watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 38 | Removal of surplus soil of distance not exceeding 50 Metre and depositing where directed at a level not exceeding 1.5 Metre above the starting point complete all as specified and directed. |
| 39 | Excavation in trenches n exc 1.5 m wide and n exc 1.5m in depth for foundation n exc 10 sqm on plan and n exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed. |
| 40 | Material and Labour for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in fdn filling and mass concrete complete all as specified and directed. |
| 41 | S&F Mild steelTMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips. |
| 42 | All as per Srl item No. 41 here-in-before but 6 to 8mm dia TMT bars as in stirrups. |
| 43 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and directed. |
| 44 | Formwork to sides of concrete foundation, footings, bases of columns, rafts and plinth beams and similar vertical or batter complete all as specified and directed. |
| 45 | Formwork to edges of concrete flat , tread, breaks in floors, window cills, concrete railing, openings in concrete walls, floor and roofs n exc 20 cm wide complete all as specified and directed. |
| 46 | M&L for Reinforced cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) for slabs supported on walls , beams and columns, in floors ,hold fast, roofs, landings and in shelves ,chhajja\"s and the like complete as specified and as directed. |
| 47 | M&L for Reinforced cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate)as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, columns etc, basement slabs under mass concrete etc. complete all as specified and as directed. |
| 48 | M&L for 15mm thick rendering in CM 1:4 finished even and smooth w/o using extra cement complete all as specified and directed. |
| 49 | M&L for three coats of whitewash on newly plastered surfaces of walls including preparation complete all as specified and directed. |
| 50 | M&L for construction of 1.20m dia x 3.00 m deep sokage well, excavation in hard/ dense soil, foundation in PCC 1:3:6, wells of honeycombed stone masonary wall, including intercepting chamber, screen chamber, RCC cover slab, filling with brick bats etc complete all as specified and directed. |
| 51 | M&L for providing PCC (1:3:6) type C-2 using 40mm graded aggregates as in concrete bed to drain pipes including packing under and haunching against the sides of pipes of bore 150mm after they are laid and tested complete all as specified and directed. |
| 52 | M&L for SGSW drain pipe 150mm dia, Grade A, laid in trenches and jointed in CM 1:1 complete all as specified and directed. |
| 53 | M&L for PCC 1:3:6 type C-1 (20 mm graded stone aggregate) precast cement concrete block masonary with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete all as specified and directed. |
| 54 | Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, regulators, switch socket outlet, bulk head fittings, tube light fittings etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed. |
| 55 | Material and Labour for Point wiring with 1.50 sq mm (nominal area), two single core PVC insulated unsheathed , 1100 volts grade, multi-stranded copper conductor FRLS Grade, in and including PVC casing capping with accessories with teak wood boxes and 3 mm thick plastic laminated sheet top cover size with all fittings and accessories including MS pressed steel terminal boxes of 1.22 mm thick of suitable size duly painted with red oxide metal primer for housing/mounting brackets switches,sockets etc, including PVC insulatedunsheathed single core multi-stranded copper conductor FRLS Grade cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly for one light/point controlled by one way switch complete all as specified and directed. |
| 56 | All as per item No 55 here-in-before but for one 3 Pin 5 Amp socket outlet controled by one switch on the independent board complete all as specified and directed |
| 57 | All as per item No 55 here-in-before but for one 3 Pin 5 Amp switch outlet controled by one switch on the same board complete all as specified and directed |
| 58 | All as per item No 55 here-in-before but for 3 pin 15 Amps socket outlet independant boarddrawn from DB andincluding PVC insulated multi stranded copper conductor4.0 sqmm 1100 volts FRLS grade and earth continuity wire4.0 sqmm PVCinsulated copper wire (Green) FRLS grade including PVC casing and capping complete all as specified and directed.. |
| 59 | S&F switch piano flush type SP, one way, 5 Amp , 240 Volts complete all as specified and directed. |
| 60 | S&F switch piano flush type SP, one way, 15 Amp , 240 Volts complete all as specified and directed. |
| 61 | S&F socket outlet, 5 A, 2 in 1 , 3 pin, 240 volts complete all as specified and directed. |
| 62 | S&F socket outlet, 15 A, 2 in 1 , 3 pin, 240 volts complete all as specified and directed. |
| 63 | Supply and fix ceiling rose surface bakelite 65 x 50 mm two to three terminals AC 230 volts complete all as specified and directed. |
| 64 | Supply and fixlamp holder, insulated body, with back plate for angular batten fittings complete all as specified and directed. |
| 65 | S&F regel batten for LED Tube universal batten for G 13 T8 lamps including making electric connection from Ceiling Rose to tube light fitting complete all as directed byEngr in Charge including photon ultra Tubelight 18 Watt (single side conncetion) ultra bright LED polycarbonate Tubelight with 10 % THD with very high efficiency suitable for installation in T8 tubelight with G 13 lamp holders to give glare free light and mounting casing box 2 NosCat No REGALBATTEN8UPTO1X22WDSBSWH & PHOTONULTRAE2.01213T8SSTL18W of Make Havells or equivalent model of Make Bajaj/ Phillips/C&G. |
| 66 | S&F environmental friendly, ultra modern, energy saving, surface mounted decorative hexagon LED bulk head 10 W including connecting up to ceiling rose with 0.5 sqmm two core copper flexible conductor cable complete all as specified and directed. Make : HAVELLS Cat Part No. HEXAFT10WLED857SSYMBOPC or equivalent model of make PHILIPS/ BAJAJ/ CG / EVEREADY |
| 67 | S&F LED lamp 15 watt, CDL, B-22 cap, (Pin type), 230 V, PF not less than 0.85 (min) , Make Havells Cat No. LHLDDEEEML8R015 or equivalent model of Make Bajaj Phillips/ Crompton/ Eveready. |
| 68 | Supply and fixsheet metal enclosures for DBs(Double door type) when MCB SPN 8 way with 200 Amps rated bus bar complete all as specified and directed. |
| 69 | Supply and fixMCB SP 6-32 Amp 240 volts,50 HZ , confirm to IS /IEC 60898 breaking capacity of 10 KA, C-curve complete all as specified and directed. |
| 70 | S&F MCB SP&N , 35 to 60 Amps, 240 volts, \"C\" series, complete all as specified and directed. |
| 71 | S&F of 1100 volts grade heavy duty cable PVC insulated aluminium conductor 16 sq mm served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire one twin core cable flat or circular complete all as specified and directed by Engr in Charge. |
| 72 | Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth lead of 4mm dia GI wire by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm C/C with one handle for liftingmade out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer-in-Charge and earth testing on completion complete all as specified and directed. |
AI Tender Summary
Tender Timeline
Aug 03, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedAug 24, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 26, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender