|
| 1 | Excavation in foundation and trenches in earth work upto all depth in all kinds of soil such as pick work jumper work,blasting work,chiselling of soft /hard rock where blasting is prohibited in all leads and lifts and including trimming of sides levelling of bed to correct grade stacking the excavated soil in 15cm.layers when required into plinth sides of foundation including consolidating each deposited layer by ramming and watering and then disposing oof all surplus excavated soil as directed in all leads and lifts and soring/strutting timbering and dewatering where ever required to the entire satisfaction of the Engineer-in-charge. |
| 2 | Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate 40 mm nominal size ) and curing complete excluding cost of form work in foundation and plinth complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 3 | Filling plinth with sand under floor including watering, ramming, consolidating & dressing complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 4 | Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu- reinforcement concrete and plain concrete work in:- |
| 5 | Foundation footing bases of columns etc and mass concrete complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 6 | Columns, pillars, post and struts. Square, rectangular or polygonal in plan complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 7 | Beam, cantilever, girders and lintelsSides and soffits of beam, beam haunching, cantilever, bressumers and lintels not exceeding 1 mtr. In depth in all heights from floor. |
| 8 | Flat surfaces such as soffits of suspended floors, roofs, landings and the like. |
| 9 | Vertical surfacessuch as wall (any thickness) partitions and the like including attached pillasters, buttresses plinth and string courses and the like complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 10 | Edges of slab and breaks in floors and wallsunder any width complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 11 | Providing & Laying cement concrete work 1 : 1.5 : 3 (1 cement : 1.5 sand : 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:- |
| 12 | Foundation footing bases of columns etc and mass concrete complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 13 | Suspended floors, roofs, landing and shelves and their support, balconies, beams, girders, bressumers and cantilever upto all floor level complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 14 | Walls any thicknessbut not less than 0.1m thickness including attached pillaster buttresses, plinth and string courses from top of foundation upto two level all floor level as per direction and to the entire satisfaction of Engineer-in-Charge. |
| 15 | Colunms pillars posts and strutsSquare, rectangular or polygonal in plan. |
| 16 | Providing and laying no fine cement concrete 1:6 (1 cement : 6 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in cement mortar 1:6 (1 cement : 6 Sand) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 17 | Precast concrete block masonry (including quion block, jamb block, closer etc.) with solid concrete block of approved size made of cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 40mm and down guage) foundation and plinth upto floor two level in cement mortar 1:6 (1 cement : 6 Sand) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 18 | Providing and fixing precast concrete manhole cover and frame, conforming to IS 12592-2002 560mm dia complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 19 | Providing and laying cement concrete flooring 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) laid in one layer finished with a floating coat of neat cement (40mm Thick) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 20 | Providing mild steel / Tor steel reinforcement for RCC work including bending binding and placing in position complete upto all floor level complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 21 | Supplying and fixing rolling shutters of approved make made of 80 mm X 1.25mm M.S laths interlocked together through their entire length and joined together at the end by end locks mounted on specially designed pipe shaft,with brackets side guides and arrangements for inside and outside locking with push pull operation complete but excluding the cost of the top cover and spring shutter having below 3.5 mtrsas per direction and to the entire satisfaction of Engineer-in-Charge. |
| 22 | Providing and laying 20cm thick composit stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6 (1 cement : 6 sand) and concrete backing with cement concrete 1:3:6 ( 1 cement : 3 sand : 6graded stone aggregate 20mm nominal size) on inner face of wall including centring, shuttering and propping complete upto floor tow level complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 23 | Brick work using common burunt clay building bricks in foundation and plinth in cement mortor 1:4 (1 cement : 4 sand) (2nd class brick) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 24 | Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, framed and fixed in position. (2nd class deodar wood) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 25 | Providing and Fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 40 mm thick. (2nd class deodar wood) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 26 | Providing and Fixing wire gauge shutters using galvenised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors, windows & clearstory windows i/c bright finished black iron enamelled hinges with necessary screws 40 mm thick (2nd class deodar wood) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 27 | Providing & Fixing M.S. plain grills of required pattern and design in iron frame of window etc.with M.S. flats, square or round bars with round headedbolts and nuts by screws complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 28 | 6mm cement plaster to ceiling in CM 1:3 ( 1Cement :3 Sand) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 29 | 15 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement: 6 sand) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 30 | Stone soling/boulder filling dry hand packed in under floor complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 31 | Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortor 1:3 (1cement : 3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete. 20 mm thick complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 32 | Providing and laying Action Tessa Vivid 3086-Africa Redwood MT flooringAC-5 of 12mm thickness of size 1214mm (L)x 193mm (W) over superior high density hard wood fibre board complete in all respects within all lead & Lift as directed by Engineer In Charge. |
| 33 | Providing and laying Duro stone vetrified tiles(300x300mmx10mm) in grey/coloured or of approved shade in flooring,treadsofstepsandlanding laid on a bed of 12mm thick cement mortar1:3(1cement:3sand)laid overandjointedwithneatcement slurryfinishedwithflushpointingin whitecementmixedwithpigment of required shade to match the shade of tiles complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 34 | Providing and fixing 10mm thick anti skidwaterproofstainandimpect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mmmanufacturedof approvedshadeandcolourin flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3(1cement :3 sand)jointed with cement slurry mixed with pigment to match the shade oftilesas required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 35 | Providing and Fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints & Fixing with nails & screws etc. complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 36 | Providing and Fixing 19mm thick Commercial Board water proof shutters for cup boards i/c Fixing with nickel plated piano hinges with screws etc. complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 37 | Providing and Fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 38 | Providing 40x3 mm iron hold fast 40 cm long including Fixing to frame with 10 cm da bolts nuts and wooden pluges and embencing in C.C. block 30x10x15 cm 1:3:6 ( 1 cement:3 sand: 6 gradedstoneaggregate 20 mmnominal size) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 39 | Providing and fixing bright finished bras sliding door boltwith bolts and nuts screws etc. complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 40 | 300 x 16 mm |
| 41 | Providing & fixing bright finished brass tower bolts (barrel type) with screws etc. complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 42 | 250 x 10 mm |
| 43 | 200x10 mm |
| 44 | Providing and Fixing bright finished brass handles with necessary screws etc. complete complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 45 | 125 mm |
| 46 | 100mm |
| 47 | Providing and Fixing oxidized M.S. Hooks and Eyes 150 mm complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 48 | Providing and Fixing 100 mm bright finished brass floor door stopper with rubber cushion screw etc. to suit shutter thickness complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 49 | Steel work welded in built up section, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead painting grating, framed guard bars ladders, railing brackedts and similar works as per direction of Engineer-in-Charge upto all lead and lift. |
| 50 | Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive 75mm Nominal bore complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 51 | Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1cement:3sand:6 graded stone aggregate 20 mm nominal size) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 52 | Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 53 | Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 54 | Applying priming coat over new wood and wood based surfaces after and inciuding preparing the suface be thoroughly cleaning oil grease dirt and othr foreign sand papering and knotting Readymixed paint brushing wood primer pink complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 55 | Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paintto give an even shade including cleaningthe surface of dirt, dust and other foreign matters sand papering and stopping with enamel paint other than white complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 56 | Applying priming coat over new steel & other metel surface after and including preparing the surface by throughly cleaing oil, grease, dirt & other foreign matter and scourd with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead, red oxide/zinc oxideas per direction and to the entire satisfaciton ofEngineer-in-charge upto all lead and lift. |
| 57 | Painting two coats (excluding priming coat) over new steel and other metal surfaces,with enamel paintto give an even shade including cleaningthe surface of dirt ,dust and other foreign matters sand papering and stopping with enamel paint other than white complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 58 | Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws :- Plastic container complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 59 | Providing and fixing vitreous China pedestal type water closet (European type) with seat and lid, 10 ltrs low level white vitreous china flushing cistern & C.P. flush bend with fitting & C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the wall and flooring wherever required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 60 | Jaquar Make EWC One Piece LYS-WHT. |
| 61 | Providing and Fixing 12mm thick 150mm wide pelmet with 25mm diametre wooden curtain rods and brackets including fixing 25X3mm M.S. flat 10cm long and plugs etc. complete. 1st class deodar wood complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 62 | Providing and fixing wash basin with C.I. brackets 15mm C.P. pillar tap, 32mm C.P. brass waste of standard pattern, including painting of fitting and brackets, cutting and making good the wall wherever required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 63 | Cera make table top wash basin matt black 630X450mm. |
| 64 | White vitreous china wash basin size 630X450mm with pedestal. |
| 65 | Providing and fixing chromium plated brass pillar cock- Jaquar make Fonte type complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 66 | Providing and Fixing 600 mm x 450 mm bevelled edge mirror of superior glass marked on 6mm thick AC sheet or plywood sheet and fixed to wooden plug with CP brass screws and washer complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 67 | Providing and Fixing CP Brass towel rail complete with CP Brass brackets fixed to wooden plug with CP Brass screws 750 mm x 20 mm complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 68 | Providing and Fixing 600 mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 69 | Providing and Fixing Toilet paper holder C.P. brass complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 70 | Providing and fixing C.P. brass angle valve 15mm without Nuts and pipe complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 71 | Providing & fixing wall mixing faucet for shower and bath woth overhead pipe (1210cm) and bathshower complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 72 | Fixing 15 mm mixer kitchen sink with top/bottom swinging spotas per direction and to the entire satisfaciton ofEngineer-in-charge upto all lead and lift. |
| 73 | Fixing to wall, ceiling & floor, galvanized nild steel tube (Heavy Class), tube fitting & clamps i/c making good the wall, ceiling & floor complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 74 | 20mm dia Nominal Bore |
| 75 | 15mm dia Nominal Bore |
| 76 | Providing and Fixing 100 mm dia cast iron grating for floor, gully or Nahni trap complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 77 | ProvidingandfixingC.P.Brass Soap dish withC.P.Brassbracketsfixedto wooden plugs with C.P. Brass screws complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 78 | Providingandfixingstainlesssteelkitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes andmakinggoodthesamebutexcluding fitting. 610 x 510 mm with bowl depth 200 mm complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 79 | Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outletconnection, 15mm nominal bore ball valve and mosquito proof PVC cover with lockingarrangement including hoisting up to all heights above ground level :-1000 litres net capacity tank complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 80 | Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and Fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18\" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 81 | 25 Liter capacity water heater (Cat-A) |
| 82 | Wiring for light point / fanpoint /exhaust fan /call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 83 | Group A |
| 84 | Group C |
| 85 | Supplying and drawing following sixe PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit as required.PVC insulated HRFR LS Copper conductor 1.5 Sq.mm. complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 86 | 3X1.5 Sq.mm |
| 87 | 3X4.0 Sq.mm |
| 88 | Supplying & Fixing of G.I. modular boxes of (140mmx78mmx50mm) size along with modular base and cover platefor modular switches in recess including providin and fixing 5 pin 5/6 Amp. modular socket outlet and 5/6 Amp modular switch, connection etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 89 | Supplying & Fixing of G.I. modular boxes of (140mmx78mmx50mm) size along with modular base and cover platefor modular switches in recess including providin and fixing 6 pin 15/16 Amp. modular socket outlet and 15/16 Amp modular switch, connections etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 90 | Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 91 | 20 mm dia |
| 92 | 25 mm dia |
| 93 | Supplyingand Fixingoffollowingway, singlepoleandneutral sheetsteel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 94 | Double door-8 way |
| 95 | Double door-6 way |
| 96 | Supplying and Fixing following rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 97 | 25 Amps. Cat-A. |
| 98 | Supplying and errection of 6 Amp to 32 Amp rating, 10 KA breaking capacity 240 Volts, C-curves minituature circuit breaker of following poles in the existing MCB DB complete with connections as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 99 | Single poleCat-A. |
| 100 | Wiring for light/power plug with 2X10 Sq. mm. PVC insulated copper conductor single core cable in surface/recessed steel conduit along with 1 No.10 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 101 | Wiring for circuit / sub-main with 4x6 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 2 No. 6 Sq.mm. (4x6+2x6) HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 102 | Providing and installation of exhaust fan of following sizes in existing opening, including making the hole to suitable size of the above fan, making good the damages, connections, testing and commissioning etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 103 | Exhaust Fan, Light duty (Domastic) 225mm sweep. |
| 104 | Providing, installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc.as required : Ceiling Fan 1400mm sweep, Category-A complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 105 | Supplying and fixing Ding-Dong/Electronic musical bell, suitable for D.C./A.C. single phase, 230 volts conplete as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 106 | Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
| 107 | Supplying and laying 8 SWG copper wire at 0.50 mtrs below ground level for earth electrode conductor including soildering etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge. |
