Public Works Department-PWD has published Infrastructural Development Of Gnc Sub-Div, Dhalai Infrastructural Development Of Gnc Sub-Div, Dhalai Tripura/Construction Of Revenue Dak Bungalow / Balance Work / Sh-Building Portion In/C. Internal Water Supply And Sanitary Installation And Concealed . Submission Date for this Tender is 27-08-2021. Civil Work Tenders in Gandacherra Tripura. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | SUB-HEAD : EARTH WORK |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. -All kinds of soil |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. -All kinds of soil |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. - All kinds of soil |
| 5 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 6 | Supplying chemical emulsion in sealed containers including delivery as specified. (i) Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 7 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment as per IS: 6313 (Part III)- Latest revision (excluding the cost of chemical emulsion): Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling: (i) With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 8 | SUB HEAD : CEMENT CONCRETE WORK |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level: |
| 10 | (i) 1:2:4 (1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 11 | (ii) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) |
| 12 | (iii) c) 1:4:8 ( 1 Cement: 4 fine sand :8 graded well burnt brick aggregate 40 mm nominal size) |
| 13 | (iv) 1:5:10 (1 Cement: 5 fine sand : 10 graded well burnt brick aggregate 40 mm nominal size) |
| 14 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer"s specification. |
| 15 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 16 | SUB HEAD : REINFORCED CEMENT CONCRETE WORK |
| 17 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement. - All work upto plinth level: |
| 18 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 19 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses,fillets ,columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement |
| 20 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 21 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five levelexcluding the cost of centring, shuttering, finishing and reinforcement |
| 22 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 23 | Centering shuttering including struttings, propping etc. and removal of form work for: |
| 24 | (i) Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 25 | (ii) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply |
| 26 | (iii) Suspended floors, roofs, landings, balconies and access platform with 12mm thick shuttering ply |
| 27 | (iv) Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply |
| 28 | (v) Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 29 | (vi) Stairs (excluding landings) except spiral-staircases with wooden plank |
| 30 | (vii) Weather shade, Chajjas, corbels etc., including edges |
| 31 | Providing precast cement concrete jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits. (i) 50mm. thick |
| 32 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (i) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 33 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. (i) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 34 | SUB HEAD : BRICK WORK |
| 35 | First class brick work in foundation and plinth including cost of all materials as required complete:- |
| 36 | (i) In Cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 37 | (ii) In Cement mortar 1:6 ( 1 cement : 6 fine sand ) |
| 38 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- (i) In cement mortar 1:6 ( 1 cement : 6 fine sand ) |
| 39 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- (i) In Cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 40 | Extra for providing & placing in position 2 nos 6mm dia MS bars at every 6th course of full brick masonry work including anchorage in joints of 75mm in each side in superstructure for all level including cost of all materials as required complete:- (i) In Cement mortar 1:6 ( 1 cement : 6 fine sand ) |
| 41 | Extra for providing & placing in position 2 nos 6mm dia MS bars at every 4th course of half brick masonry work including anchorage in joints of 75mm in each side in superstructure for all level including cost of all materials as required complete:- (i) In Cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 42 | SUB HEAD : MARBLE WORK |
| 43 | Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels:- (i) 18 mm thick Granite of any colour and shade duly approved:- - Area of slab over 0.50 sqm. |
| 44 | Providing edge moulding to approved thickness marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete at all levels as required as per design approved by the Engineer-in-charge:- (i) 18 mm thick Granite work. |
| 45 | SUB HEAD : WOOD & PVC WORK |
| 46 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : (i) Karai Wood |
| 47 | Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20 × 12 mm for fixing panelling and or glazing as per direction of Engineer-In-Charge. (i) Local Teak Wood - 35mm. thick shutters |
| 48 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for paneled or paneled and glazed shutters 25 to 40 mm thick. (i) Local Teak Wood 16mm thick |
| 49 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters. (i) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 50 | Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia (heavy type) curtain rod with nickel plated brackets including fixing with 25 × 3 mm M.S. flat 10 cm long and rawl plugs 50 mm long (designation 10 no.) etc. all complete. |
| 51 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. |
| 52 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 53 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 54 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 55 | (i) 300 x 16 mm |
| 56 | (ii) 250 x 16 mm |
| 57 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 58 | (i) 300 x 10 mm. |
| 59 | (ii) 250 x 10 mm. |
| 60 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 61 | (i) 125 mm. |
| 62 | (ii) 100 mm. |
| 63 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. (i) Single rubber stopper |
| 64 | Providing and fixing bright finished 100mm mortice lock with 6 levers without pair of handles for aluminium door with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge. |
| 65 | Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws . |
| 66 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter). |
| 67 | SUB HEAD : STEEL WORK |
| 68 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required. |
| 69 | Providing and fixing fan clamp type-I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete. |
| 70 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc.,of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 71 | SUB HEAD : FLOORING WORK |
| 72 | Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips etc. complete. 40 mm thick with 20 mm stone aggregate |
| 73 | Providing and laying cement plaster skirting upto 300 mm height with cement mortar 1 : 3 ( 1 cement : 3 fine sand ) finished with a floating coat of neat cement including rounding of junctions etc. complete. |
| 74 | (i) 18mm thick. |
| 75 | (ii) 21mm thick. |
| 76 | Providing and fixing 25 mm thick pre-polished colored concrete designer tiles making by strong vibratory compaction technology using 50% white cement and 50% ordinary cement of size 300mm x 300mm, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete as per direction of the Engineer-in-charge. |
| 77 | Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 fine sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete. (i) 8mm thick Rajnagar marble tiles (polished) |
| 78 | Providing and fixing Marble stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishingcomplete. i) 18 mm thick Marble stone - Raj Nagar Plain Marble |
| 79 | Extra for prefinished nosing to treads of steps of marble stones |
| 80 | Providing and fixing Kota stone in floors over 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishingcomplete. Kota stone slab 25mm thick |
| 81 | Providing and fixing 1st quality ceramic glazed wall tiles (minimum 200 x 300) conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in-charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. |
| 82 | SUB HEAD : ROOFING & CEILING WORK |
| 83 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming toIS:5382leaving10mmgapforthermalexpansion: (i) Single socketed pipe - 110 mm OD |
| 84 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: |
| 85 | (i) Coupler - 110 mm. |
| 86 | (ii) Single equal tee without door - 110 x 110 x 110 mm |
| 87 | (iii) Bend 87.5 - 110mm |
| 88 | (iv) Plain Shoe - 110mm |
| 89 | Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. (i) 110 mm |
| 90 | Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. (i) 100 mm |
| 91 | SUB HEAD : FINISHING WORK |
| 92 | 12 mm cement plaster of mix |
| 93 | (i) Cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 94 | (ii) Cement mortar 1:6 ( 1 cement : 6 fine sand ) |
| 95 | 15 mm cement plaster on the rough side of single or half brick wall of mix: |
| 96 | (i) Cement mortar 1:6 ( 1 cement : 6 fine sand ) |
| 97 | 6 mm cement plaster of mix : |
| 98 | (i) Cement mortar 1:3 ( 1 cement : 3 fine sand ) |
| 99 | Neat cement punning. |
| 100 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i) New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 101 | Finishing walls with water proofing cement paint of required shade of approved brand and manufacture [Payment shall be made afterubmission of Test Certificate issued by the Manufacturer] : (i) New work ( two or more coats applied @ 3.84 kg/10 sqm) |
| 102 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i) With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 103 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: (i) Two or more coats on new work |
| 104 | SUB HEAD : ALUMINIUM WORK |
| 105 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ppropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.luminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :- |
| 106 | (i) For fixed portion of approved quality:- - Anodisedaluminium(anodisedtransparentordyedto requiredshadeaccordingtoIS:1868,Minimumanodic coating of grade AC 15). |
| 107 | (ii) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittingsherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- i) Anodisedluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). - Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 108 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- (i) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 109 | Filling the gap in between aluminium frame and adjacent RCC/brick work by providing weather silicon sealant over backer rod of approved quality etc. complete as per architectural drawing and direction of the Engineer-in charge:- (i) Upto 5 mm depth and 5 mm width. |
| 110 | Providing and fixing stainless steel ( SS 304 grade ) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-in-charge:- (i) 255 x 19 mm. |
| 111 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality completeas per direction of Engineer-in-charge:- (i) Anodised aluminium of grade AC 15. |
| 112 | Providing and fixing 100 mm brass locks ( best make of approved quality ) with 6 levers without pair of handles for aluminium doors including necessary cutting and making good etc. completeas per direction of Engineer-in-charge. |
| 113 | SUB HEAB : WATER PROOFING WORK |
| 114 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with : i) Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 115 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with waterroofing cement compound, as directed by Engineer-in-Charge and consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 116 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound, as directed by Engineer-in- Charge and consisting of applying : (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and fine sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. |
| 117 | SUB HEAD : SANITARY INSTALLATIONS |
| 118 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushingcisternwithmanuallycontrolleddevice(handlelever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (i) White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 119 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (i) W.C. pan with ISI marked white solid plastic seat and lid |
| 120 | Providing and Fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : (i) Range of three urinal basins with10 litre white P.V.C. automatic flushing cistern. |
| 121 | Providing and Fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. Automatic flushing cistern, with fittings, standard size G.I. flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc. wherever required : (i) Single squatting plate with 5 litre P.V.C. automatic flushing cistern. |
| 122 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings: (i) Flat back wash basin of size 550x400mm. |
| 123 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 124 | (i) Semi rigid pipe - 32 mm dia |
| 125 | (ii) Flexible pipe - 32 mm dia |
| 126 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 127 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc. complete. |
| 128 | Providing and fixing soil, waste and vent pipes : (i) 100 mm dia - Sand cast iron S&S pipe as per IS: 1729. |
| 129 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/ cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. (i) For 100 mm dia pipe |
| 130 | Providing and fixing heel rest sanitary bend. (i) 100 mm dia - Sand cast iron S&S pipe as per IS: 1729. |
| 131 | Providing and fixing double equal junction of required degree with access door,insertion rubber washer 3 mm thick, bolts and nuts complete : (i) 100 x 100 x 100 x 100 mm - Sand cast iron S&S pipe as per IS: 1729. |
| 132 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. (i) 100 x 100 x 100 mm - Sand cast iron S&S pipe as per IS: 1729. |
| 133 | Providing and fixing single equal plain junction of required degree (i)100 x 100 x 100 mm - Sand cast iron S&S pipe as per IS: 1729. |
| 134 | Providing and fixing sand cast iron S&S offsets as per IS: 1729 (i) 152 mm off set - With 100 mm dia pipe |
| 135 | Providing and fixing terminal guard. (i) 100 mm - Sand cast iron S&S pipe as per IS: 1729. |
| 136 | Providing and fixingcollar : (i) 100 mm - Sand cast iron S&S pipe as per IS: 1729. |
| 137 | Providing lead caulked joints to sand cast iron/ centrifugally cast (spun) iron pipes and fittings of diameter: (i) 100 mm dia. |
| 138 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: (i) 100 mm inlet and 100 mm outlet - Sand cast iron S&S pipe as per IS: 1729. |
| 139 | Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size ) including necessary plaster and pointing in cement mortar 1:4(1cement: 4 coarse sand): (i) 100 mm dia. |
| 140 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms |
| 141 | Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms |
| 142 | SUB HEAD : WATER SUPPLY |
| 143 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply ncluding all PP - R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. - Concealed work including cutting chases and making good the walls etc. |
| 144 | (i) PN- 16 Pipe, 16 mm OD[SDR 7.4] |
| 145 | (ii) PN- 16 Pipe, 20 mm OD[SDR 7.4] |
| 146 | (iii) PN- 16 Pipe, 25 mm OD[SDR 7.4] |
| 147 | (iv) PN- 16 Pipe, 32 mm OD[SDR 7.4] |
| 148 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP - R plain & brass threaded polypropylene random fittings including trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work (i) PN-16 Pipe, 32 mm OD (SDR-7.4) |
| 149 | Providing and fixing brass bib cock of approved quality: (i) 15 mm dia nominal bore |
| 150 | Providing and fixing brass stop cock of approved quality: (i) 15 mm dia nominal bore |
| 151 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): |
| 152 | (i) 25 mm dia nominal bore |
| 153 | (ii) 32 mm dia nominal bore |
| 154 | Providing and fixing gun metal non-return valve of approved quality (screwed end): |
| 155 | (i) 32 mm nominal bore - Vertical |
| 156 | Constructing masonry Chamber 30x30x50 cm, inside , in brick work in cement mortar 1:4 (1 cement :4 fine sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design : (i) With Second Class bricks |
| 157 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 158 | SUB HEAD : SEWAGE & DRAINAGE WORK |
| 159 | Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete : (i) 150mm diameter |
| 160 | Providing and laying cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) alround S.W. pipes including bed concrete as per standard design: (i) 150 mm diameter S.W. pipe |
| 161 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 162 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 163 | SUB HEAD : CONCEALED CONDUITING FOR INTERNAL ELECTRIFICATION WORK |
| 164 | Supplying and fixing of the following PVC conduit (medium guage) with all accessories on slab/recessed on wall etc as required. |
| 165 | (i) 20 mm dia |
| 166 | (ii) 25 mm dia |
| 167 | (iii) 32 mm dia |
| 168 | Supplying & installation of metallic fan clamp box of standard size with 3 mm thick bakelite/plastic cover as required:- |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
